Astria Fireplaces Envy CD Instruction Sheet

Type
Instruction Sheet
GENERAL INFORMATION
HORIZONTAL TERMINATION
SHROUD KIT
The horizontal Termination Shroud Kit may be used as a decorative cover
for the square termination and to minimize exposure to the hot surface
of the termination.
This kit contains one termination shroud kit and these instructions.
If you encounter any problems, need clarification of these instructions
or are not qualified to properly install this kit, contact you local distribu-
tor or dealer.
Read this instruction sheet in its entirety before beginning the installation.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
OPERATION MANUALS PROVIDED WITH THE APPLIANCE APPLY TO
THESE INSTRUCTIONS.
HEARTH PRODUCTS
KITS AND ACCESSORIES
INSTALLATION INSTRUCTIONS FOR THE HORIZONTAL TERMINATION SHROUD KIT FOR USE
WITH SQUARE TERMINATIONS WHICH MAY BE USED WITH DIRECT VENT GAS FIREPLACES
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
P/N 750246M
REV. D 10/2015
PFS
®
USC
WARNING
THIS KIT MUST BE INSTALLED BY A QUALIFIED SERVICE
TECHNICIAN OR OTHER QUALIFIED AGENCY ACCORDING
TO THE MANUFACTURER’S INSTRUCTIONS, ALL CODES
AND REQUIREMENTS OF THE AUTHORITY HAVING JURIS-
DICTION IN THE USA OR CANADA. THE QUALIFIED AGENCY
PERFORMING THIS WORK ASSUMES RESPONSIBILITY FOR
THIS INSTALLATION.
WARNING
THE TERMINATION SHROUD PROVIDES A BARRIER TO PRE-
VENT DIRECT CONTACT WITH THE HOT TERMINATION EXCEPT
AT THE TOP PORTION OF THE TERMINATION SHROUD. THIS
AREA IS EXTREMELY HOT DUE TO THE DISCHARGING FLUE
GASES.
KIT CONTENTS (See Figure 1)
1 ea. Shroud Top
1 ea. Shroud Body
1 ea. Bottom Screen
8 Ea. Screws,10 X 1/2” Black Phillips
1 ea. Instruction Sheet
Figure 1
Termination Shroud Kit
Cat. No. Model Description
H5820 SV4.5-HTSK Termination Shroud Kit
Printed in U.S.A. © 2007 IHP LLC
P/N 750246M REV. D 10/2015
Figure 2
Termination
Securing Screws
(Five) For Shroud
Body To Shroud Top.
Install From The
Bottom Up.
Screw Flanges
(Five Places)
Bottom Screen
Termination
Shroud - Top
Termination
Shroud - Body
Back Off These Two Screws
(Both Sides) And Slide
Shroud Body Into Place.
Securing Screws
(Three) For Bottom
Screen To Shroud Body.
Install From The Bottom Up.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
IHP reserves the right to make changes at any time, without notice, in design, materials,
specifications, prices and also to discontinue colors, styles and products. Consult your local
distributor for fireplace code information.
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
INSTALLATION INSTRUCTIONS
NOTE: Shroud kit installation does not require the removal of the square
termination.
Step 1. Turn off the fireplace and allow the termination to cool before
proceeding.
Step 2. Loosen the four (4) screws on the existing square termination
(refer to Figure 2).
Step 3. Slide the body of the shroud over the termination screws that
have been loosened, setting it in place (refer to Figure 2).
Step 4. Re-tighten the four (4) screws into place, securing the shroud
body over the termination.
Step 5. Position the shroud top over the shroud body and screw it into
the flanges located on both the shroud top and shroud body,
using five (5) screws (as shown in Figure 2).
NOTE: The five (5) screws are to be attached from the bottom.
Step 6. Attach the bottom screen onto the body of the shroud, using the
three (3) screws into each of the three flanges on the shroud
body (see Figure 2 ).
Step 7. If desired, paint shroud to any color.
  • Page 1 1
  • Page 2 2

Astria Fireplaces Envy CD Instruction Sheet

Type
Instruction Sheet

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI