DIGITAL DOOR VIEWER
User manual
and guarantee card
VDP-01C1 ERIS
DEVICE CHARACTERISTICS
Digital door viewer VDP-01C1 enables to view the visitor at the door, substituting classical, optical
door viewers. LCD 3.2’’ monitor guarantees the comfort of usage. The device can be helpful for
elderly, people of short height and people with weak eyesight.
The main advantage of the device is its simplicity of installation. The user does not need any
special tools during assembly process, no additional wires are needed for proper operation. What
is more, it does not damage the door structure – the user can use the hole of the old door viewer.
The image quality is ensured under the condition that the camera’s surrounding is lightened
properly.
Elements included in the set:
- Monitor with mounting frame,
- Camera module,
- Locking barrel.
INSTALLATION
To install the device properly the user has to:
1. Replace the existing door viewer on the door or drill a 14-28 mm hole in the door at eye level.
2. Insert the camera from the outside door while inserting the washer between the back of
the lens and the door. The user should make sure that the white mark on the camera points
upwards.
3. At the back of the door viewer there is a metal frame that has to be opened (it should be
moved down and then pulled to the user).
4. Fit the back cover of the main frame over the end of the lens. Then screw the locking barrel
onto the threaded part of the camera, turn the mainframe clockwise for one turn to make it
rmly tightened.
Note:
During the installation in the door the user should carefully turn the device while tightening
and avoid moving the camera. Not obeying this advice can result in the mechanical damage
of the wire connecting camera with monitor.
5. Connect the single wire from lens to the white connector in the mainframe.
Note: The wire should be connected in such way that the wire does not turn 180 degrees.
6. Put 3 AAA batteries in.
7. Close the mainframe and hook the screen over the two little brackets in the top of the back
cover. Push downwards to make it rmly secured.
8. Push the button to get the image displayed. Aer 10 second image disappears automatically.
Note:
If it occurs that due to any reason the monitor cannot remain its horizontal orientation (smooth
surface of door, cracking the door that loosens the barrel and so on) it is advised to additionally
apply two thin strips of double-sided tape as shown in the g. 7.
Fig. 1
Fig. 4
Fig. 2
Fig. 5
Fig. 3
Fig. 6 Fig. 7
DEVICE OPERATION
1. Press the power button, the unit will continue working for about 10 seconds. Then it will turn
o automatically.
2. The power is expected to be valid for about 10 minutes. If the image becomes blurred, please
replace the batteries.
TECHNICAL PARAMETERS
Type and size of the screen 3,2” LCD
Viewing angle 110O
Camera sensor CMOS 1,3 mpx
Power supply 4,5V DC (3 x AAA)
Door thickness range 42…72 mm
Hole diameter range 14…28 mm
Material Plastic + brass
Monitor dimensions 115 x 62 x 16 (mm)
Netto weight 0,2 kg
The copy of declaration of conformity is available on : http://www.eura-tech.eu
EURA-TECH Sp. z o.o.
84-200 WEJHEROWO, ul. Przemysłowa 35A
tel. +48 58 678 81 00, service: tel. +48 58 678 81 20, fax +48 58 678 81 01
www.eura-tech.eu
All rights reserved. Pictures, graphs and texts are the property of “Eura-Tech” Sp. z o.o.
Copying, distributing and publication without permission of author is forbidden.
WARRANTy
As the only distributor of the Eura products, Eura-Tech is obliged to ensure ecient warran-
ty and post-warranty service. In the countries where Eura-Tech has neither its own service
network, nor DOOR-TO-DOOR service, the quality claims are dealt with by authorised distri-
butors of the Eura products on the basis of the signed distribution agreements. Within the
framework of such agreements, Eura-Tech will ensure nancing of the possible repairs and
delivery of spare parts.
/
