Cell2 SAS32R Installation & Operation Manual

Brand: Cell2

Model: SAS32R

Type: Installation & Operation Manual

Cell2 SAS32R is a siren and PA system with a range of features to keep you safe and informed on the road. With a powerful 109dB siren, you can alert other drivers and pedestrians to your presence, while the built-in PA system allows you to make clear announcements or give directions. The easy-to-use switch panel lets you control all functions with a single hand, and the included microphone ensures your voice is heard loud and clear. Whether you're a professional driver or just want added peace of mind on the road, Cell2 SAS32R is the perfect solution.

SAS32R SPEAKER SIREN SYSTEM W/

SW300 CONTROL SWITCH & MIC SET

NOTICE TO INSTALLER

Before installation and operation -- read all instructions and warnings.

Deliver this manual to the end user of this equipment.

Installation & Operation Manual

INSTALLATION............................................................................................................ 2

MOUNTING.................................................................................................................. 3

WIRING........................................................................................................................ 5

CONTROLLER FUNCTION......................................................................................... 6

PA BROADCAST......................................................................................................... 7

LOW VOLTAGE PROTECTION MODE....................................................................... 7

TABLE OF CONTENTS

- 1 -

INSTALLATION

Proper installation of the product requires the installer to have a good understanding of

automotive electronics, systems and procedures. It is essential to install the unit

properly to ensure safe and reliable operation.

Please read through all instructions thoroughly and carefully before installing the unit.

Failure to follow these instructions could result in serious damage to the unit or vehicle

and may void warranties.

The correct mounting and wiring is the key to the effectiveness of SAS32R & SW300.

Installers must read and follow installation instructions and warnings in the manual from

the original manufacturer.

The operator should verify the siren system is fastened to the vehicle securely and is

functioning properly. Failure to follow all safety precautions and instructions may cause

property damage, injury, or death.

Ensure that any switch control panel is located in an area that allows both the vehicle

and the control panel to be operated safely in any driving condition.

WARNING Sound Hazard - Sound level from siren speaker (109dB at 2M) may cause hearing damage.

Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity.

(Ref. OSHA 1910.95 for occupational noise exposure guidelines)

CONTENTS: The installer must have good knowledge of electricity, vehicle electrical

systems and emergency equipment. Always seek professional assistance if in doubt.

- 2 -

MOUNTING

Speaker Siren Unit

Secure the mounting bracket to an appropriate and suitable area.

RUBBER PAD

BRACKET

FLAT WASHER

SPRING WASHER

M6 HEX HEAD NACHIRE BOLT

RUBBER

MOUNTING BRACKET

FLAT WASHER

SPRING WASHER

0.590" Maximum

0.511" Minimum

Permanent mounting of this product may require drilling. It is necessary to make

sure that no other vehicle components could be damaged by this process.

Check both sides of the mounting surface before drilling.

Siren Speaker must only be mounted horizontally to the ground. Fail to follow

may cause undesired water to ingress into speaker, damage to the product and

void the warranty.

WARNING

- 3 -

Note: Please only mount the horn facing

out horizontally to the ground.

When installing surface mount, make sure to consider the thickness of the mounting

surface and washer. The installer must use the supplied screws to match the rear

threaded insert of the Switch Panel. Fail to do so may cause damage to the product and

void the warranty.

Surface Mount:

Handlebar Mount:

Suggested Sheet Metal Thickness: 0.059"(1.5mm)

0.83"

(21mm)

Screw (1/4 in)

Spring Washer

Flat Washer

Mounting Surface

- 4 -

Switch Panel

Select a mounting location that will not interfere or impede the operation and/or function

of any existing equipment. Securely mount the switch using the provided handlebar

clamp.

Handlebar Diameter Ø0.87"~Ø1.26" (Ø22mm~Ø32mm)

WIRING

IGN

White

POWER -GND

Black

POWER +VDC

Red

POWER +VDC

Red

Light Outupt #1

Yellow

Light Output #2

Orange

Ground

White-Black

Voice Signal

Purple

PTT

Blue

Ground

White-Black

To SW300 +VDC

Green

Siren Button Output

Pink

MAN Button Output

Brown

Light Button Output

Grey

Cable 1

(Power & Light Output)

- 5 -

Cable 2

(Switch & Mic Signal)

Mic Set

Control

Switch

Car Ignition Key

Power Source

Device #1

Device #2

(Max Output Amperage @ 5A)

(Fuse Rating:

15A @ 13.6VDC)

CONTROLLER FUNCTION

Light Output

Siren Tone

Manual

1. At any moment, short press once to activate or inactivate all

Light output #1 & #2 together.

2. While all light outputs are activated, long press to activate only

Light output #1.

3. While only front output is activated, long press again to activate

only Light output #2.

4. While only rear output is activated, long press again to activate

both Light output #1 & #2 together.

1. Press once to turn the siren on in WAIL tone.

2. While siren is activated, press again once to cycle through all available tones.

3. While siren is activated, long press to disable siren tone.

1. If siren tone is not activated, press and hold for Manual WAIL tone. WAIL tone will ramp

up to peak and hold till button is released (or cut-off before it peaks).

2. If a siren tone is activated, press and hold for “Tone-Change”. The Siren will return back

to the previous tone when button is released.

- 6 -

Siren Tone “ToneChange”

WAIL

YELP

YELP PHASER

PHASER HILO

HILO PHASER

#Standard Tone

1 WAIL

2 YELP

3 PHASER

4 HILO

PA BROADCAST

PA Activation

Press “Push-to-Talk” button on the side of the Mic to activate

PA broadcasting. PA broadcasting will override all current

Siren Tone. Action will resume when PTT is released.

Mic Volume Adjustment Knob

(available on selected mic model only)

The knob located on the top right corner of the controller will

adjust mic volume (high or low). Turn clockwise for high

volume; turn anticlockwise for low volume.

While unit is in operation, whenever power voltage drops under 11.6VDC for over 10

seconds, SW300 controller will blink to notify Low Voltage issue is at presence; all controller

function will be disabled.

LOW VOLTAGE PROTECTION MODE

If Low Voltage issue continued for another 10 seconds, all Siren function will be disabled

automatically and entre Low Voltage Protection Mode.

While unit is in Low Voltage Protection Mode, if power voltage resumes back to 13VDC and

above for over 10 seconds, Siren unit will exit Low Voltage Protection Mode and back to its

default standby.

- 7 -

Mic Volume

Adjustment Knob

PTT

PTT Clip-on Mic

Handheld Mic

Cell2 SAS32R Installation & Operation Manual

Cell2 SAS32R Installation & Operation Manual

Cell2 SAS32R Installation & Operation Manual

Related papers

Other documents