Gage Bilt GB743SRVT User manual

Brand: Gage Bilt

Model: GB743SRVT

Type: User manual

GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE

E-MAIL US FOR A DISTRIBUTOR NEAR YOU.

GB743SRVT

S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR

ALL OTHER SERIAL NUMBERS.

INSTALLATION TOOL

ORIGINAL INSTRUCTIONS

44766 Centre Court, Clinton Twp., MI. 48038 USA

Ph: +1 (586) 226-1500 Fax: +1 (586) 226-1505

[email protected] / www.gagebilt.com

GAGE BILT

MADE in USA

2 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

TABLE OF CONTENTS

Page

EU Conformity and Warranty ................................................................................................................................................... 3

Description and Technical Specifications ............................................................................................................................... 4

Description of Functions ........................................................................................................................................................... 5

Warnings ..................................................................................................................................................................................... 6

Principle of Operation ............................................................................................................................................................... 7

How to set-up the GB743SRVT ................................................................................................................................................. 8

How to use the GB743SRVT ...................................................................................................................................................... 9

Maintenance and Hydraulic Thread Preparation ................................................................................................................... 10

Filling ....................................................................................................................................................................................... 11

Bleeding ................................................................................................................................................................................... 12

Troubleshooting ...................................................................................................................................................................... 13

Overhaul .............................................................................................................................................................................. 14-16

Parts Lists ............................................................................................................................................................................ 17-18

DEXRON® III Oil Safety Data (SDS) ........................................................................................................................................ 19

How to Assemble Evacuation Tube / Vacuum ....................................................................................................................... 20

Nose Assembly Selection Chart ............................................................................................................................................. 21

Accessories ......................................................................................................................................................................... 22-24

3 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

Seller warrants that all goods covered by this catalog will conform

to applicable specifications and will replace or repair, EXW our plant, any

goods providing defective from faulty workmanship, or material, for 1 year

from date of shipment.

Said warranty to remain in effect if, and only if, such goods are

used in accordance with all instructions as to maintenance, operation and

use, set forth in manuals and instruction sheets furnished by seller.

Sellers obligation under this warranty shall be limited to the repair

or rework of the goods supplied or replacement thereof, at Seller’s option,

and in no case is to exceed the invoice value of said goods. Under no

circumstances will the seller be liable for incidental or consequential

damages or for damages incurred by the buyer or subsequent user in

repairing or replacing defective goods or if the goods covered by this

warranty are reworked or subjected to any type of additional processing.

This warranty is void if Seller is not notified in writing of any

rejections or defects within 1 year after the receipt of the material by the

customer.

THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES

EXPRESSED OR IMPLIED, INCLUDING MERCHANTABILITY.

WARRANTY

DECLARATION OF CONFORMITY

MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct., Clinton Twp., Michigan U.S.A. +1(586-226-1500)

WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS

TO THE FOLLOWING DIRECTIVES AND STANDARDS

Machinery Directive 2006/42/EC

EN12100-1 & 12100-2:2010

EN ISO 11148-1:2011

The Supply of Machinery (Safety) Regulations 2008

EU REPRESENTATIVE: Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany

EQUIPMENT DESCRIPTION: GB743SRVT FASTENER INSTALLATION TOOL

This product specified above conforms to the above dIrectives and standards.

SIGNATURE:

NAME: Tim Simmons

PRODUCT MANAGER

CLINTON TWP., MI. U.S.A.

DEC 2022

+1(586) 226-1500

GAGE BILT

4 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

SPECIFICATIONS

Hand Held Weight - 2.75 lbs. (1.25 kg)

Air pressure req'd - 90 - 100 p.s.i. (6.2 - 6.9 bar)

Air consumption - .30 SCF/cycle (8.50 L/cycle)

Hydraulic Oil - Automatic Transmission Oil,

Dexron® III, or equivalent.

Setting stroke - .900" (22.86 mm)

Rated pull load - 4,000 lbs. (17.80 kN)

Noise level - 81.5 dB(A)

Vibration - Tested – No Hazards Found

The GB743SRVT is a pneumatic-hydraulic split handle installation tool designed specifically for the efficient installation of blind fasteners.

This tool’s unique "split" system provides the operator with a lightweight ergonomic tool. The handle and head assembly when held in hand

weighs 2.75 lbs. (1.25 kg). The entire split handle installation tool weighs 7.25 lbs. (3.29 kg). It has a .900” (22.86 mm) fastener setting stroke.

The GB743SRVT split handle installation tool operates on 90 to 100 psi. (6.2 - 6.9 bar) of air pressure, with 90 psi. (6.2 bar) providing

maximum efficiency. At 90 psi. (6.2 bar) air pressure, the GB743SRVT does not exceed 81.5 dB(A) and consumes .30 SCF/cycle (8.50 L/cycle).

The GB743SRVT comes with 3 feet (.91 m) of hose and a vacuum system, please consult our engineering department for specific applications.

The air inlet has a 1/4 - 18 female pipe thread for accepting the user's air hose fitting.

THE GB743SRVT IS ORDERED FASTENER SPECIFIC. TO CHANGE TOOL OVER TO INSTALL OTHER FASTENERS, SEE CHARTS ON

PAGES 20 & 21 FOR PART NUMBERS.

DESCRIPTION

WARNING: Any other use is forbidden.

ENVIRONMENTAL USE

WARNING: Do not operate in an explosive atmosphere.

The GB743SRVT can be operated between 0ºF - 118ºF (-17.8ºC / 47.8ºC)

5 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

DESCRIPTION OF FUNCTIONS

Image may not reflect actual tool

Evacuation Tube

Air Hose

Hydraulic Hose

Actuator Lever Assembly

Vacuum

Regulator

Actuator Assembly

Air Inlet

Bleeder Screw

Hanger

Head Assembly

Handle Assembly

Grip

6 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

SAFETY WARNINGS

OPERATING HAZARDS:

1. Use of tool can expose the operator’s hands to hazards, including crushing, impacts,

cuts, abrasions and heat. Wear suitable gloves to protect hands.

2. Operators and maintenance personnel shall be physically able to handle the bulk,

weight and power of the tool.

3. Hold the tool correctly; be ready to counteract normal or sudden movements and have

both hands available.

4. Maintain a balanced body position and secure footing.

5. Release the start-and-stop device in the case of interruption of energy supply.

6. Use only lubricants recommended by the manufacturer.

7. Avoid unsuitable postures as it is likely for these positions not to allow counteracting

of normal or unexpected movement of the tool.

8. If the tool is fixed to a suspension device, make sure that fixation is secure.

9. Beware of the risk of crushing or pinching if nose equipment is not fitted.

10. Due to the tool weight, it is recommended safety shoes be worn during operation.

11. It is recommended tool be operated not more than 50 out of every 60 minutes, where

prolonged use is expected.

REPETITIVE MOTIONS HAZARDS:

1. When using the tool, the operator can experience discomfort in the hands, arms,

shoulders, neck or other parts of the body.

2. While using the tool, the operator should adopt a comfortable posture while maintain-

ing a secure footing and avoiding awkward or off balanced postures. The operator

should change posture during extended tasks; this can help avoid discomfort and

fatigue.

3. If the operator experiences symptoms such as persistent or recurring discomfort, pain,

throbbing, aching, tingling, numbness, burning sensations or stiffness, these warning

signs should not be ignored. The operator should tell the employer and consult a

qualified health professional.

ACCESSORY HAZARDS:

1. Disconnect tool from energy supply before changing the nose assembly or accessory.

2. Use only sizes and types of accessories approved by the manufacturer. Do not use

other types or sizes of accessories.

WORKPLACE HAZARDS:

1. Slips, trips and falls are major causes of workplace injury. Be aware of slippery surfac-

es caused by use of tool and also of trip hazards caused by the air line or hydraulic

hose.

2. Proceed with care in unfamiliar surroundings. There could be hidden hazards, such as

electricity or other utility lines.

3. The tool is not intended for use in potentially explosive atmospheres and is not insu-

lated against contact with electrical power.

4. Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if

damaged by the tool.

NOISE HAZARDS:

1. Exposure to high noise levels can cause permanent, disabling hearing loss and other

problems, such as tinnitus (ringing, buzzing, whistling or humming in the ears). There-

fore, risk assessment and the implementation of appropriate controls for these haz-

ards are essential.

2. Appropriate controls to reduce the risk may include actions such as damping materials

to prevent workpieces from “ringing”.

3. Always use hearing protection.

4. Operate and maintain the assembly power tool for non-threaded mechanical fasteners

as recommended in the instruction handbook, to prevent an unnecessary increase in

the noise level.

5. Select, maintain and replace the consumable/inserted tool as recommended in the

instruction handbook, to prevent an unnecessary increase in noise.

6. If the power tool has a silencer, always ensure that it is in place and in good working

order when the power tool is being operated.

VIBRATION HAZARDS:

1. Exposure to vibration can cause disabling damage to the nerves and blood supply of

the hands and arms.

2. Wear warm clothing when working in cold conditions and keep your hands warm and

dry.

3. If you experience numbness, tingling, pain or whitening of the skin in your fingers or

hands, stop using the assembly power tool for non-threaded mechanical fasteners,

tell your employer and consult a physician.

4. Support the weight of the tool in a stand, tensioner or balancer, because a lighter grip

can then be used to support the tool.

GENERAL SAFETY RULES:

1. For multiple hazards, read and understand the safety instructions before installing,

operating, repairing, maintaining, changing accessories on, or working near the

assembly power tool for non-threaded mechanical fasteners.

2. Only qualified and trained operators shall install, adjust or use the assembly power

tool for non threaded mechanical fasteners.

3. Do not modify this assembly power tool for non-threaded mechanical fasteners. Modifications can

reduce effectiveness of safety measures and increase the risks to the operator.

4. Do not discard safety instructions; give them to the operator.

5. Do not use assembly power tool for non-threaded mechanical fasteners if it has been damaged.

6. Tools shall be inspected monthly to verify all ratings and markings required are legible.

The employer/user shall contact the manufacturer to obtain replacement marking

labels when necessary.

ADDITIONAL SAFETY RULES FOR PNEUDRAULIC POWER TOOLS:

1. Air under pressure can cause severe injury.

2. Always shut off air supply, drain hose of air pressure and disconnect tool from air

supply when not in use, before changing accessories or when making repairs.

3. Never direct air at yourself or anyone else.

4. Whipping hoses can cause severe injury. Always check for damage or loose hoses and fittings.

5. Cold air shall be directed away from hands.

6. Whenever universal twist couplings (claw couplings) are used, lock pins shall be

installed and whip check safety cables shall be used to safeguard against possible

hose-to-tool or hose-to-hose connection failure.

7. Do not exceed the maximum air pressure stated on the tool or manual.

8. Never carry an air tool by the hose.

PROJECTILE HAZARDS:

1. Disconnect the tool from the energy source when changing inserted tools/nose as-

semblies or accessories.

2. Be aware that failure of the workpiece, accessories, or the inserted tool/nose assembly

itself can generate high-velocity projectiles.

3. Always wear impact resistant eye protection during operation of the tool.

4. Ensure that the workpiece is securely fixed.

5. Check that the means of protection from ejection of fastener and/or stem is in place

and operative (such as the deflector, pintail collection bottle or catcher bag).

6. Forcible ejection of the mandrel from the front of the nose assembly is possible.

TERMS AND SYMBOLS

- Product complies with requirements

- Hearing protection and eye protection

WARNINGS - Must be understood to avoid severe

personal injury.

CAUTIONS - show conditions that will damage

equipment and/or structure.

Notes - are reminders of required procedures.

- Read manual prior to using equipment

- Wear safety boots

- Product complies with requirements

7 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

PRINCIPLE OF OPERATION

Pressurized Oil

Unpressurized Oil

Pressurized Air

Unpressurized Air

PULL Cycle RETURN Cycle

Images may not reflect actual tool

Air Piston moves up

Air Piston moves down

Air exhaust

Air exhaust when lever

assembly depressed

Air exhaust

When the lever assembly is depressed, the pressurized air inside of the tool is released allowing spring pressure to move the valve

spool assembly causing the air to be redirected. The air is directed to the top of the air piston assembly, moving it in a downward

direction. The air below the air piston assembly is then directed through the valve sleeve and exhausted out of the bottom of the tool.

Simultaneously, the piston rod assembly connected to the air piston assembly is also moving down, forcing hydraulic oil up and into the

front side of the head cylinder assembly, causing the piston to move to the rear of the head cylinder assembly. The internal components of

the attached nose assembly are also moving with the piston to start the fastener installation. When the fastener installation is completed,

the lever assembly is released. Air pressure is then built up inside of the handle assembly causing the valve spool assembly to return

to its original position and reversing the sequence directing air pressure to the rear of the head cylinder assembly, causing the piston

to move to the forward position.

Piston Rod Assembly moves up

Piston Rod Assembly moves down

8 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

HOW TO SET-UP THE GB743SRVT

The tool is shipped with a red plastic plug in the air inlet connector. The connector has a 1/4 - 18 female pipe thread to accept end-

user air hose fitting. The tool comes with oil and is ready to use.

1. Remove red plastic shipping plug from Tee (A-1766) (air inlet) and screw in your quick disconnect (air) fitting.

2. Connect tool to air hose with 90 psi. (6.2 bar) using clean, dry air. 3/8” (9.52 mm) minimum diameter air line is recommended.

Cycle tool five times by depressing and releasing lever assembly (724017).

3. Disconnect air hose from tool.

4. Select proper nose assembly (see nose assembly selection chart on pg. 20 for more information). Apply Vibra-tite® pt. #405125 to

all threads and allow it to set 20 minutes prior to assembly. Screw collet onto piston and slide anvil over collet and secure with

jam nut (70820). (See proper data sheet for further instructions).

5. Connect air supply.

HEAD CYLINDER

Image may not reflect actual tool

FASTENER WORK

ACTUATOR

NOSE ASSEMBLY

RED SHIPPING PLUG

USER QUICK

DISCONNECT FITTING

AIR HOSE

AIR INLET

TEE A-1766

EVACUATION TUBE

WARNING: Only qualified and trained operators shall install, adjust or use the assembly power tool for non-threaded

mechanical fasteners.

WARNING: Operator MUST read and understand all warnings and cautions.

WARNING: It is required that eye protection, hearing protection and safety boots be worn at all times while handling this

equipment.

WARNING: The users or the user’s employer must assess specific risks that could be present as a result after each use

based on their application.

● Ensure there is adequate clearance for tool and operator's hands before proceeding. Keep fingers clear of any

moving parts. Keep fingers clear from fasteners and installed materials. Severe personal injury may result.

● Verify the air lines and/or hydraulic hoses are not a trip hazard.

● Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if damaged by the tool.

WARNING: Do not actuate fastener in the air. Personal injury from fastener ejecting may occur.

WARNING: Air is exhausted from the bottom of the tool. Direct bottom of the tool (exhausted air) away from operator, other

persons working in the vicinity, foreign matter and liquid.

WARNING: Do not carry from hoses or use as a hammer.

WARNING: Do not use in explosive atmosphere.

WARNING: Ensure air hose is securely connected to avoid possible hose whipping.

WARNING: Always disconnect air supply when tool is not in use to prevent accidental start-up.

WARNING: Ensure there is adequate clearance for tool and operator hands.

WARNING: Do not operate this tool without deflector, pintail catcher bag or pintail collection bottle in place.

CAUTION: Do not use beyond the design intent.

9 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

Images may not reflect actual tool or fastener

Blind Fasteners

1. Insert fastener.

2. Insert fastener into nose assembly.

Note: Always hold tool so pulling head is perpendicular to

surface of material in which fastener is being installed.

Exert firm pressure against fastener during installation.

3. Press actuator to start cycle.

4. Release actuator as soon as fastener breaks.

5. Repeat steps 1 - 4.

HOW TO USE THE GB743SRVT

WARNING: Only qualified and trained operators shall install, adjust or use the assembly power tool for non-threaded

mechanical fasteners.

WARNING: Operator MUST read and understand all warnings and cautions.

WARNING: It is required that eye protection, hearing protection and safety boots be worn at all times while handling this

equipment.

WARNING: The users or the user’s employer must assess specific risks that could be present as a result after each use

based on their application.

● Ensure there is adequate clearance for tool and operator's hands before proceeding. Keep fingers clear of any

moving parts. Keep fingers clear from fasteners and installed materials. Severe personal injury may result.

● Verify the air lines and/or hydraulic hoses are not a trip hazard.

● Ensure that there are no electrical cables, gas pipes, etc., which can cause a hazard if damaged by the tool.

WARNING: Do not actuate fastener in the air. Personal injury from fastener ejecting may occur.

WARNING: Air is exhausted from the bottom of the tool. Direct bottom of the tool (exhausted air) away from operator, other

persons working in the vicinity, foreign matter and liquid.

WARNING: Do not carry from hoses or use as a hammer.

WARNING: Do not use in explosive atmosphere.

WARNING: Ensure air hose is securely connected to avoid possible hose whipping.

WARNING: Always disconnect air supply when tool is not in use to prevent accidental start-up.

WARNING: Ensure there is adequate clearance for tool and operator hands.

WARNING: Do not operate this tool without deflector, pintail catcher bag or pintail collection bottle in place.

CAUTION: Do not use beyond the design intent.

10 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

TORQUE SPECIFICATIONS

Socket Head Cap Screws (400061 and 400066) = 40 inch lbs. (4.52 Nm).

Button Head Cap Screws (A-928) = 40 inch lbs. (4.52 Nm).

Packing Plug (744118) = 45 foot lbs. (61 Nm).

Flexlock Nut (400559) = 40 inch lbs. (4.52 Nm).

End Cap (743214) = 45 foot lbs. (61 Nm).

Button Head Cap Screws (402482) = 35 - 40 inch lbs. (3.95 - 4.52 Nm). (Do NOT over-tighten).

DAILY MAINTENANCE

WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or

wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures.

WARNING: Excessive contact with hydraulic oil and lubricants must be avoided.

WARNING: Maintenance personnel MUST read and understand all warnings and cautions.

WARNING: Disconnect tool from its power source before performing maintenance, cleaning or when replacing worn or

damaged components. Severe personal injury may occur if power source is not disconnected.

WARNING: Read safety datasheet documents for all applicable materials.

Note:

• Dispose of hydraulic oil in accordance with manufacture safety datasheet.

• All tool materials are recyclable except rubber o’rings, seals and wipers.

The performance of any tool depends upon good maintenance practices. Following these minimal requirements daily will extend the

life of your tool.

*Check tool and nose assembly for damage. (Replace/Repair if necessary). See Overhaul pgs.14 - 16 for tool repair.

*Inspect hoses and couplings for wear, damage and leaks. (Replace/Repair if necessary). (See hydraulic thread preparation below).

*Verify that hydraulic hose fittings and couplings, air and electrical connections are secure. Tighten, Replace or Repair if necessary

(See hydraulic thread preparation below).

*Cycle the tool several times to assure there are no leaks during use.

*Keep hydraulic system free of dirt.

*Proper care by operators is necessary in maintaining full productivity and reducing downtime.

*Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet surfaces that jaws ride on with light

machine oil on a daily basis.

*All Screwed End Caps, Base Covers, Air Fittings, Air Actuators, Screws and Nose Assemblies are to be examined at the end of each

working shift to check that they are secure.

*For a complete overhaul, service tool kit (GB740SHTK) is recommended. See overhaul pgs. 14 - 16.

WEEKLY MAINTENANCE

• Keep the hydraulic system full (only use Dexron® III or equivalent) and free of air by using the air bleeder assembly (704153) on a weekly

basis or as needed. (See Filling and Bleeding procedures pgs. 11 - 12).

SEE TROUBLESHOOTING (PG. 13) AND OVERHAUL (PGS. 14 - 16) FOR FURTHER GUIDANCE.

CLEANING AND LUBRICATING PROCEDURE

Image may

not reflect

actual tool

Daily cleaning and lubrication of nose assembly will greatly reduce downtime and increase life of components. Using sewing machine

oil, or an equivalent cleaner/lubricant, follow instructions below.

HYDRAULIC THREAD PREPARATION

IMPORTANT: Be sure to use thread sealant on all hydraulic fittings, Loctite® 545 or equivalent or a non-hardening Teflon® thread

compound such as Slic-tite®. Tighten until fitting feels snug and then continue to tighten 1/2 to 1 full turn. CAUTION: Over tightening

can easily distort the threads. DO NOT USE TEFLON® TAPE. CAUTION: Teflon® tape is an excellent thread sealer, however, if it is not

properly applied, pieces of Teflon® may enter the hydraulic system and cause a malfunction or damage.

LUBRICATING

Lubricate nose assembly after each cleaning

and as often as needed.

1. Disconnect tool vacuum line (if equipped).

2. Point nose assembly into oil as shown.

3. Cycle tool 8 - 10 times and wipe dry.

CLEANING

Clean nose assembly daily or as often as needed.

1. Dip into mineral spirits or similar solvent to clean jaws

and wash away metal chips and debris. DO NOT allow

jaws to come in contact with other solvents. DO NOT let

jaws soak. Dry jaws immediately.

2. Disassemble nose assembly and use a sharp “pick”

to remove embedded particles from grooves of jaws.

11 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

IMPORTANT: Be sure to use thread sealant on all hydraulic fittings, Loctite® 545 or equivalent or a non-hardening Teflon® thread

compound such as Slic-tite®. Tighten until fitting feels snug and then continue to tighten 1/2 to 1 full turn. CAUTION: Over tightening

can easily distort the threads. DO NOT USE TEFLON® TAPE. CAUTION: Teflon® tape is an excellent thread sealer, however, if it is not

properly applied, pieces of Teflon® may enter the hydraulic system and cause a malfunction or damage.

1. Put the piston rod wrench assembly (704149) into the top of handle assembly (744129), pushing down firmly until piston rod

assembly (744136) is completely in the down position.

2. Fill oil passage and reservoir with Automatic Transmission Oil, Dexron® III or equivalent. The reservoir is the area surrounding

the power cylinder (743131). When looking at the top of the handle assembly (744129), the oil passage is the hole that has a

counterbore for o’ring (S832). Do not overfill causing oil to go in air passage hole.

3. Install gasket (704129), o’ring (S832), button head cap screws (A-928) and manifold-handle (744303) to handle assembly (744129)

keeping hydraulic hose (A-336) towards plug (704313), located on handle assembly (744129) and torque button head cap screws (A-928)

to 40 inch lbs. (4.52 Nm).

4. Push piston (743407) full forward. Install gasket (704129) and o’ring (S832) on manifold-head assembly (744306). Assemble head

cylinder assembly (743116) to manifold-head assembly (744306) and lever assembly (724017) using socket head cap screws

(400061 & 400066). Apply Loctite 242 to all cap screws and torque to 40 inch lbs. (4.52 Nm).

5. Remove pin and lever from lever assembly (724017). Coil tool hoses up on bench and lay handle assembly (744129) down on side

so that the hole marked #4 on manifold handle (744303) is to the top. Set head cylinder assembly (743116) over a small bucket or can.

Completely fill up fill bottle (745263).

6. Remove button head cap screw (402482) and stat-o-seal (S572) from manifold-handle (744303) hole #4 and manifold-head assembly (744306)

hole #4. Connect fill bottle (745263) to manifold-handle (744303) hole marked #4.

7. In one continuous squeeze force oil into manifold-handle (744303) until oil starts to flow from bleeder hole marked #4 on manifold

-head assembly (744306). While still squeezing the fill bottle (745263) use other hand to replace button head cap screw (402482)

and stat-o-seal (S572) on manifold-head (744306) and torque to 35 - 40 inch lbs. (3.95 - 4.52 Nm). Do not over tighten. This may

require two people.

8. Remove fill bottle (745263) and replace stat-o-seal (S572) and button head cap screw (402482) on manifold-handle (744303) and

torque to 35 - 40 inch lbs. (3.95 - 4.52 Nm). Do not over tighten.

9. Proceed to bleeding instructions on pg. 12 to remove air from hydraulic system.

FILLING PROCEDURE

WARNING: Do not cycle tool without air bleeder assembly (704153), or the screw and stat-o-seal, installed in tool head. Severe

personal injury could result.

WARNING: Use CAUTION when removing screws, air bleeder assembly (704153) and fill bottle (745263). Hydraulic oil may be

under pressure.

CAUTION: Before filling handle assembly (744129), air piston assembly (744121) must be all the way down.

CAUTION: When forcing piston rod assembly (744136) downward, with head cylinder assembly (743116) removed, hydraulic oil will

eject forcibly from handle assembly (744129).

CAUTION: When bleeding tool, ensure tubing is free from kinks or other obstructions.

Note:

• Fill Bottle (745263) (sold separately) is required.

* FILLING & BLEEDING VIDEO AVAILABLE AT: http://www.gagebilt.com/rivet_tools_videos.php

Hole marked #4 on Manifold

Handle (744303)

Oil Passage hole

O’ring (S832)

Handle Assembly and

Power Cylinder hole

***Keep air

hole free

from oil***

Images may not reflect actual tool.

Hole marked #4 on Manifold Head

Assembly (744306) facing upward.

Fill Bottle (745263)

12 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

1. Ensure pin and lever on lever assembly (724017) has been removed. Stand handle assembly (744129) on floor, stretch hose and

head cylinder assembly (743116) upward and lay flat on a table or bench. When bleeding tool always keep the head cylinder

assembly (743116) higher than the handle assembly (744129).

2. Remove button head cap screw (402482) and stat-o-seal (S572) from manifold-handle (744303) hole marked #3. Attach air bleeder

assembly (704153) to manifold-handle (744303) hole marked #3 in an upright position.

3. Connect the tool to air supply and cycle tool ten times holding the actuator assembly-air (704130) down for 2 - 3 seconds between

cycles to remove any air from the tool.

4. Disconnect air supply. Remove air bleeder assembly (704153) from manifold-handle (744303) and replace with button head cap

screw (402482) and stat-o-seal (S572) and torque to 35 - 40 inch lbs. (3.95 - 4.52 Nm). Do not over tighten.

5. Remove button head cap screw (402482) and stat-o-seal (S572) from hole marked #4 manifold-head assembly (744306) and attach

air bleeder assembly (704153) in an upright position.

6. Connect air supply. Cycle tool ten times removing any air bubbles.

7. Disconnect air supply. Remove air bleeder assembly (704153) and replace button head cap screw (402482) and stat-o-seal (S572)

and torque to 35 - 40 inch lbs. (3.95 - 4.52 Nm). Do not over tighten.

8. Connect air supply. Cycle tool ten times and check stroke of .900” (19.8 mm) using instructions a thru c and diagrams below.

We recommend using dial calipers.

a. With the actuator assembly-air (704130) released, check dimension (A).

b. Holding actuator assembly-air (704130) check dimension (B).

c. Subtract dimension (B) from dimension (A). If stroke is not consistent within 1/64" (.396 mm) repeat bleeding procedure until stroke met.

For your consideration, Gage Bilt offers a depth gage (Pt.# A-1935) to help simplify and more accurately check your tool stroke.

Please contact Gage Bilt for more information.

9. Disconnect air supply.

10. Re-attach lever and pin to lever assembly (724017).

BLEEDING PROCEDURE:

* FILLING & BLEEDING VIDEO AVAILABLE AT: http://www.gagebilt.com/rivet_tools_videos.php

Note:

• Air Bleeder Assembly (704153) (sold separately) is required.

Images may not reflect actual tool.

Hole marked #3 on

Manifold Handle (744303) Air Bleeder

Assembly

(704153)

Hole marked #4 on Manifold Head

Assembly (744306) *located on far side*

WARNING: Do not cycle tool without air bleeder assembly (704153), or the screw and stat-o-seal, installed in tool head. Severe

personal injury could result.

WARNING: Use CAUTION when removing screws, air bleeder assembly (704153) and fill bottle (745263). Hydraulic oil may be

under pressure.

CAUTION: Before filling handle assembly (744129), air piston assembly (744121) must be all the way down.

CAUTION: When forcing piston rod assembly (744136) downward, with head cylinder assembly (743116) removed, hydraulic oil will

eject forcibly from handle assembly (744129).

CAUTION: When bleeding tool, ensure tubing is free from kinks or other obstructions.

DIM “A”

1.140 (29 mm)

DIM “B”

.240 (6.1 mm)

13 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

Providing all maintenance conditions have been met, follow this systematic approach to diagnosis.

1. MORE THAN ONE PULL IS REQUIRED TO BREAK FASTENER.

a) Tool needs to be bled. (See filling and bleeding procedures pgs. 11 - 12).

b) Spring has fatigued, replace.

c) Jaws are stripped or packed with chips. Clean or replace.

d) Incorrect nose tip.

2. SLOW OR PARTIAL OPERATION WHEN THE LEVER ASSEMBLY (724017) IS DEPRESSED.

a) Polyseal (A-1135) and O’ring (400792) on piston (743407) could be worn or damaged. Replace.

b) Back-up Rings (S908) and O’ring (A-201) on piston rod assembly (744136) could be worn or damaged. Replace.

c) Muffler (744143) or filter inside valve spool assembly (743142) may be plugged with dirt. Clean thoroughly and back-blow

with compressed air.

d) Hole in metering screw in valve spool assembly (743142) may be blocked or damaged. Hole diameter should be .028" (.71 mm).

Clear and size or replace.

3. NO OPERATION WHEN LEVER ASSEMBLY (724017) IS DEPRESSED.

a) Tool seized due to mechanical failure or damaged parts.

4. OIL LEAKAGE.

a) DO NOT OPERATE WITH OIL LEAKING FROM TOOL. HIGH PRESSURE OIL MAY CAUSE SEVERE PERSONAL INJURY.

b) Any oil leaking externally should be traced to its source. An o'ring or seal that leaks should be replaced.

5. AIR BYPASS FROM VALVE HOUSING.

a) If the spring (744144) breaks or dislodges, air will flow freely through the muffler (744143). Replace or reset.

Valve spring installation tool (744251) is recommended.

b) Check o'rings on valve sleeve (743144), valve spool assembly (743142), and valve plug (744142). If worn or damaged, replace.

Valve sleeve removal tool (744152) is recommended.

6. FASTENER STEM JAMMED IN NOSE ASSEMBLY.

a) Nose assembly components require service. DISCONNECT AIR FROM TOOL, remove the nose from the tool and disassemble.

Replace worn or broken parts. Clean the surface the jaws ride on.

b) Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble.

c) Incorrect follower.

7. PINTAIL IS NOT BEING VACCUMED THROUGH.

a) Check vacuum line is not kinked and that the bend radius is not too small.

b) Check vacuum pressure using vacuum gage 703567 (sold separately).

Note: Offset nose assemblies must be check by removing the vacuum line from the nose assembly.

c) Press gage against the vacuum line or nose assembly to create seal.

Optimum vacuum pressure at nose assembly must be between 15 - 22 inHg. (381 - 558.8 mmHg).

TROUBLESHOOTING

1. Remove vacuum regulator (703515) from hose and fitting.

2. Remove (4) S.H.C.S. from front of regulator and disassemble.

3. Clean both pieces in clean mineral spirits and blow dry.

4. Reassemble and connect hoses.

5. Check vacuum pressure using vacuum gage (703567) (sold separately).

Press gage against the vacuum line or nose assembly to create seal.

Optimum vacuum pressure at nose assembly must

be between 15 - 22 inHg. (381 - 558.8 mmHg).

Note: The vacuum regulator may visually appear clean, but still may be

contaminated with a thin film, therefore, the steps above should be

performed to assure best performance.

HOW TO CLEAN VACUUM REGULATOR

Fitting

(4) S.H.C.S.

Tube

703515 Vacuum Regulator

Image may not reflect actual tool

Deflector

14 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

OVERHAUL

WARNING: Only qualified and trained personnel shall perform overhaul.

WARNING: Personnel must read and understand all warnings and cautions.

WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or

wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures.

WARNING: Disconnect tool from its power source before performing overhaul. Severe personal injury may occur if power

source is not disconnected.

WARNING: Excessive contact with hydraulic oil and lubricants must be avoided. (See safety data sheet documents for all

applicable materials).

WARNING: When operating, repairing or overhauling tool, wear approved eye protection. Do not look in front of tool or

rear of tool when installing fastener.

WARNING: Use only Gage Bilt hydraulic hoses and couplings, or equivalent, rated for 5,000 psi. (344.8 bar) working pressure.

WARNING: Ensure air hose is securely connected to avoid possible hose whipping (Air Actuated Tools only).

WARNING: Depress actuator assembly-air (704130) and disconnect from air, with the piston in the rear position, before overhaul.

Severe personal injury may occur if air hose is not disconnected. USE CAUTION when forcing piston rod assembly

downward with head cylinder removed. Hydraulic oil will eject forcibly from handle assembly.

Perform overhaul in a clean, well lit area using care not to scratch or nick any smooth surface that comes in contact with an o'ring.

Use of Lubriplate® (Gage Bilt part no. 402723) or other lubricant is recommended during reassembly to prevent tearing or distorting of o'rings.

The disassembly and re-assembly procedure can be accomplished by utilizing the following instructions and parts lists on pgs. 14 - 18.

Use extreme care during disassembly and re-assembly not to mar or nick any smooth surface that comes in contact with seals. Before installing

seals, always apply a good lubricant, such as Lubriplate®, to the surfaces. Clean parts in mineral spirits or other o'ring compatible

solvent being sure to clean o'ring grooves. Inspect components for scoring, excessive wear or damage.

Note:

• Dispose of hydraulic oil in accordance with manufacture safety datasheet.

• All tool materials are recyclable except rubber o’rings, seals and wipers.

• It is recommended that service tool kit (GB740SHTK) (see below) be used to facilitate overhaul.

• Use of SERVICE KIT (743017), which contains a complete set of o’rings, back-up rings, screws, washers and gasket,

can achieve a complete overhaul.

TOOL DISPOSAL

1. When tool life is met, drain hydraulic oil from tool and dispose of the hydraulic oil in accordance with the safety datasheet.

2. Disassemble tool and remove all rubber o’rings, seals, wipers and hydraulic hoses. All tool materials are recyclable except rubber

o’rings, seals, wipers and hydraulic hoses. Dispose of rubber materials in accordance with the material safety datasheet.

Part No. Description

704149 Piston Rod Wrench Assembly

704151 Power Cylinder Tool Assembly

704150 Packing Plug Wrench Assembly

704152 Seal Guide

704153 Air Bleeder Assembly

744251 Valve Spring Installation Tool

744152 Valve Sleeve Removal Tool

S1178 Valve Extractor

745263 Fill Bottle (Large)

204330 Seal Guide

GB740SHTK Service Tool Kit Includes:

15 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

ACTUATOR ASSEMBLY-AIR

WARNING: Disconnect tool from its power source before actuator removal or installation. Severe personal injury may occur if

power source is not disconnected.

CAUTION: Actuator assembly-air (704130) can break if not careful.

CAUTION: Do not over tighten actuator assembly-air (704130). Snug tighten only.

OVERHAUL

Image may not

reflect actual tool

REMOVING ACTUATOR ASSEMBLY-AIR (704130)

1. Remove lever assembly (724017) including pin.

2. With lever assembly (724017) removed, insert a 5/8” open end box wrench / adjustable wrench

around actuator assembly-air (704130).

3. Loosen the actuator assembly-air (704130).

4. Remove wrench. Unthread and remove the actuator assembly-air (704130) with fingers from the

manifold head assembly (744306).

INSTALLING ACTUATOR ASSEMBLY-AIR (704130)

1. Apply Teflon® tape onto threads of actuator assembly-air (704130) one to two wraps.

2. Thread the actuator assembly-air (704130) all the way into manifold head assembly (744306) with fingers.

3. Insert and turn 5/8” open end box wrench / adjustable wrench and snug tight approximately 1/4 - 1/2 turn.

4. Re-attach the lever assembly (724017) with pin.

16 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

WARNING: Disconnect tool from its air source before disassembly.

OVERHAUL

1. Remove nose assembly and adapter from tool before attempting disassembly of head cylinder assembly (743116).

2. Remove end cap (743214).

3. Push against threaded end of piston (743407) to slide it out of head cylinder assembly (743116). Be careful not to damage threads

or cause burrs on polished piston rod surface.

The re-assembly sequence is the opposite of disassembly. (See Filling and Bleeding procedures pgs. 11 - 12). Apply Loctite® #242

and torque the socket head cap screws (400061 and 400066) uniformly to 40 inch lbs. (4.52 Nm) to prevent leakage around the gasket (704129).

HEAD

HANDLE

To inspect air cylinder bore, remove base cover (744124). Any further disassembly will require removal of the manifold-handle (744303) first.

For complete disassembly.

1. Remove base cover (744124).

2. Holding tool upright, remove four button head cap screws (A-928) and lift manifold-handle (744303) from handle assembly (744129) and

set aside o'ring (S832) and gasket (704129).

3. Empty all hydraulic oil into an approved container and dispose of in accordance with the material safety data sheet.

4. Place piston rod wrench assembly (704149) down into top of power cylinder (743131) and into the hex of piston rod assembly

(744136). While holding the piston rod wrench assembly (704149), remove flexlock nut (400559) using a 7/16" socket wrench or an

adjustable wrench. Still holding piston rod wrench assembly (704149), remove air piston assembly (744121) using packing plug

wrench assembly (704150), by turning counterclockwise.

5. When air piston assembly (744121) is completely free from piston rod assembly (744136), tap or push on the piston rod wrench

assembly to eject air piston assembly (744121) from bottom of handle assembly (744129).

6. After removal of air piston assembly (744121), slide piston rod assembly (744136) back up to the end of its travel. Using packing

plug wrench assembly (704150) remove packing plug (744118).

7. With packing plug (744118) removed, power cylinder (743131) can be removed by pushing on power cylinder tool assembly (704151)

when inserted into top of power cylinder (743131).

To reassemble the handle assembly (744129).

1. Reverse the above procedure, being certain that all o'rings are properly lubricated before installation. Torque packing plug (744118)

to 45 foot lbs. (61 Nm).

2. Attach the seal guide (704152) to the piston rod assembly (744136) and tap the piston rod assembly (744136) through the packing

plug (744118).

3. Attach air piston assembly (744121) and flexlock nut (400559). Torque flexlock nut to 40 inch lbs. (4.52 Nm).

4. Attach air piston assembly (744121) to piston rod assembly (744136).

5. With the piston rod in the down position, fill oil passage on top of handle assembly (744129) with automatic transmission oil, Dexron® III or

equivalent. When looking at top of handle assembly (744129) the oil passage is the hole that has a counterbore for (S832) o'ring.

6. Replace gasket (704129) and o'ring (S832), just prior to replacing manifold-handle (744303). Torque all screws to manual specifications.

(See Filling & Bleeding procedures pgs. 11 - 12) & (See torque specs. pg. 10).

AIR VALVE

1. Remove pin (744149) and muffler (744143).

2. Insert valve extractor (S1178) into end of valve plug (744142) and pull it out.

3. Using the same procedure, pull out valve spool assembly (743142).

4. It should never be necessary to remove valve sleeve (743144) unless the ports in the valve sleeve (743144) are plugged from

contaminated air. If ports are plugged, use needle nose pliers to grasp end of spring (744144), turning clockwise and pulling to

dislodge from groove in casting. Valve spring installation tool (744251) will facilitate the proper installation of the spring (744144).

5. Valve sleeve (743144) can be pulled out using valve sleeve removal tool (744152).

17 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

PARTS LIST

18 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

PARTS LIST

19 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

DEXRON® III OIL SAFETY DATA

FIRST AID MEASURES

Eye: No specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes with water.

Skin: No specific first aid measures are required. As a precaution, remove clothing and shoes if contaminated. To remove the material

from skin, use soap and water. Discard contaminated clothing and shoes or thoroughly clean before reuse.

Ingestion: No specific first aid measures are required. Do not induce vomiting. As a precaution, get medical advice.

Inhalation: No specific first aid measures are required. If exposed to excessive levels of material in the air, move the exposed person to

fresh air. Get medical attention if coughing or respiratory discomfort occurs.

Note to Physicians: In an accident involving high-pressure equipment, this product may be injected under the skin. Such an accident

may result in a small, sometimes bloodless, puncture wound. However, because of its driving force, material injected into a fingertip can

be deposited into the palm of the hand. Within 24 hours, there is usually a great deal of swelling, discoloration, and intense throbbing

pain. Immediate treatment at a surgical emergency center is recommended.

FIRE

Leaks/ruptures in high pressure system using materials of this type can create a fire hazard when in the vicinity of ignition sources (e.g.

open flame, pilot lights, sparks, or electric arcs).

FLAMMABLE PROPERTIES:

Flashpoint: (Cleveland Open Cup) 178 °C (352 °F) Minimum

EXTINGUISHING MEDIA: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames.

PROTECTION OF FIRE FIGHTERS:

Fire Fighting Instructions: This material will burn although it is not easily ignited. See Section 7 for proper handling and storage. For fires

involving this material, do not enter any enclosed or confined fire space without proper protective equipment, including self-contained breathing

apparatus.

Combustion Products: Highly dependent on combustion conditions. A complex mixture of airborne solids, liquids, and gases including

carbon monoxide, carbon dioxide, and unidentified organic compounds will be evolved when this material undergoes combustion.

ACCIDENTAL RELEASE MEASURES

Protective Measures: Eliminate all sources of ignition in vicinity of spilled material.

Spill Management: Stop the source of the release if you can do it without risk. Contain release to prevent further contamination of soil,

surface water or groundwater. Clean up spill as soon as possible. Use appropriate techniques such as applying non-combustible

absorbent materials or pumping. Where feasible and appropriate, remove contaminated soil. Place contaminated materials in disposable

containers and dispose of in a manner consistent with applicable regulations.

ECOLOGICAL INFORMATION

Waste disposal: In accordance with all environmental regulations applicable to your area.

Spillage: Prevent entry into drains, sewers and water course. Soak up with diatomaceous earth or other inert material. Store in

appropriate container for disposal.

Ecotoxicity: This material is expected to be harmful to aquatic organisms and may cause long-term adverse effects in

the aquatic environment. The ecotoxicity hazard is based on an evaluation of data for the components or a similar material.

HANDLING

Precautionary Measures: DO NOT USE IN HIGH PRESSURE SYSTEMS in the vicinity of flames, sparks and hot surfaces. Use only in

well ventilated areas. Keep container closed. Keep out of the reach of children.

General Handling Information: Avoid contaminating soil or releasing this material into sewage and drainage systems and bodies of

water.

Static Hazard: Electrostatic charge may accumulate and create a hazardous condition when handling this material. To minimize this

hazard, bonding and grounding may be necessary but may not, by themselves, be sufficient. Review all operations which have the

potential of generating and accumulating an electrostatic charge and/or a flammable atmosphere (including tank and container filling, splash

filling, tank cleaning, sampling, gauging, switch loading, filtering, mixing, agitation, and vacuum truck operations) and use appropriate

mitigating procedures.

DISPOSAL CONSIDERATIONS

Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place

contaminated materials in containers and dispose of in a manner consistent with applicable regulations.

20 REV. 4/23

GB743SRVT S/N: 1070 AND ABOVE

PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

SEE TABLE 1 ON PG. #21

See pg. 13 on “how to clean vacuum”

HOW TO ASSEMBLE EVACUATION TUBE / VACUUM

Page is loading ...

Gage Bilt GB743SRVT User manual

Gage Bilt GB743SRVT User manual

Gage Bilt GB743SRVT User manual

Related papers

Other documents