Eaton xComfort MEM F940x Operating instructions

Brand: Eaton

Model: xComfort MEM F940x

Type: Operating instructions

MA-MEM_F940X.qxd/01.2015c

IL019061ZU / 136211172

Eaton Industries (Austria) GmbH, A-3943 Schrems

www.eaton.eu/documentation

xComfort F94XX Control Buttons

T=+5°C - +40°C

T=-25°C - +70°C

IP20

MRF

Min. Version 3.5

Min. Version 2.0

F9400 F9401 F9402 F9404

Surface mounting plate 1 Gang Button 2 Gang Button 4 Gang Button

F9400 Surface

mounting plate

F940x Button module CP902xx Clip on plate

Typical Application

Scope of delivery

Mounting Frame Decorative Plastic Metal Plate

Style List No List Finish List No Finish

Surface Mounting Frame F9400 CP902WH White CP902SS Stainless Steel

CP902BM Black Matt CP902HP Highly Polished

Copa Flush 2 Module C902 CP902GL Gold Metalic CP902SB Satin Bronze

CP902SL Silver Metalic CP902PB Polished Brass

CP902BL Blue Metalic

CP902GY Grey

Style List No List Finish List No Finish

Premera Flush 2 Module P902 White moulded only - no cover White moulded only - no cover

plate needed plate needed

6 7

Click

P9400 Surface

Mounted on

flat surface

P9400 Flush

Mounted on

wall box

P9400 Surface /Flush mount

with clip on cover

Screw caps if

required

4 x Click

Flush mount Premera

Frame e.g.P902

1 2

3V-CR2450N

ca. 60-90% ca. 80-95% ca. 20-60% ca. 0-10% ca. 70-90%

P9400 Surface / Flush mounting frame

Flush mounting frame e.g. P902

Prise off „Clip on“

Cover

Insert screwdriver to release

module from surface plate

Mounting

screws

Screw caps

if fitted

Remover screw cap discs, if fitted,

along with mounting screws to

release flush plate from wall box

and allow access to battery at rear

of module

Note: If Push button modules are either mounted on metal back boxes or used with metal clip on plates then the RF range may be restricted.

Eaton RF System Basic Mode Quick Reference

Symbols: Sensors: Actuators:

Link Device Unlink Device (selectively)

Reset actuator (all settings & connections)

Manual Operation

LED is on LED flashes 5 times LED is on

Lamp (LED) is on Lamp (LED) is on

1. Link devices

Assign a pushbutton to an actuator

1. Press the configuration pushbutton with a screwdriver

for less than 0.5 sec => actuator enters teach-in mode

the LED in the actuator is on

2. Press the selected pushbutton for less than 0.5 sec

3. LED in the actuator flashes twice for confirmation

4. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => actuator leaves teach-in mode

Assign a remote control to an actuator

1. Press the configuration pushbutton with a screwdriver

for less than 0.5 sec => actuator enters teach-in mode,

the LED in the actuator is on

2. Press the selected remote push button for less than 0.5 sec

3. The LED in the actuator flashes twice for confirmation

4. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => actuator leaves teach-in mode

Assign a room thermostat to an actuator

1. Press the configuration pushbutton with a

screwdriver for less than 0.5 sec => actuator

enters teach-in mode, the LED in the actuator is on

2. Turn the control knob to +

3. The LED in the actuator flashes twice for confirmation

4. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => actuator leaves teach-in mode

Assign a channel of the binary input in

switch mode

1. Press the configuration button on the binary

input (the mains supplied version requires a screwdriver) for selecting the mode, switch mode is Mode 2, LED

flashes 2x for Mode 2

2. Open contact of the binary input

3. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => actuator enters teach-in mode, the

LED in the actuator is on

4. Close contact of the binary input

5. The LED in the actuator flashes twice for confirmation

6. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => actuator leaves teach-in mode

Assign a channel of the binary input in push button

mode

1. Press the configuration button on the binary input (the

mains supplied version requires a screwdriver) for

selecting the mode, push button mode is Mode 1, LED

flashes 1x for Mode 1

2. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => actuator enters teach-in mode,

the LED in the actuator is on

3. Press pushbutton on the contacts of the binary input for less than 0.5 sec =>

4. The LED in the actuator flashes twice for confirmation

5. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => actuator leaves teach-in mode

2. Unlink devices

Unlink an assigned pushbutton

1. Press the configuration pushbutton with a screwdriver

for less than 0.5 sec => actuator enters teach-in mode,

the LED in the actuator is on

2. Press the selected pushbutton until the LED has flashes 5 times

3. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => actuator leaves teach-in mode

Unlink an assigned pushbutton on the remote control

1. Press the configuration pushbutton with a screwdriver

for less than 0.5 sec => actuator enters teach-in mode,

the LED in the actuator is on

2. Press the selected remote push button until the LED has flashed 5 times

3. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => actuator leaves teach-in mode

Unlink an assigned room thermostat

1. Press the configuration pushbutton with a

screwdriver for less than 0.5 sec => actuator

enters teach-in mode, the LED in the actuator is on

2. Turn the control knob on the room thermostat to -

3. The LED in the actuator flashes 5 times for confirmation

4. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => actuator leaves teach-in mode

Unlink an assigned channel of the binary input in

switch mode

1. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => actuator enters teach-in mode, the

LED in the actuator is on

2. Open contact of the binary input

3. Wait until the LED in the actuator has flashed 5 times

4. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => actuator leaves teach-in mode

Unlink an assigned channel of the binary input in

push button mode

1. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => actuator enters teach-in mode, the

LED in the actuator is on

2. Press pushbutton on the contact of the binary input until LED has flashed 5 times

3. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => actuator leaves teach-in mode

3. Manual operation:

Manual operation of switching actuator, dimming

actuator

1. Press the configuration pushbutton with a screwdriver

longer than 2 sec => actuator enters manual mode for

10 sec, the LED flashes fast

2. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => Lamp (LED) is on

3. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => Lamp (LED) is off

4. The actuator leaves automatically the manual mode

Manual operation of the Shutter actuator

1. Press the configuration pushbutton with a

Screwdriver for longer than 2 sec => actuator enters

the manual mode for 10 sec the LED flashes fast

2. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => Shutter moves up

3. Press the configuration pushbutton with a screwdriver for less than 0.5 sec => Shutter moves down

4. After 10 sec the actuator leaves automatically the manual mode

4. Reset actuator

1. Press the configuration pushbutton with a screwdriver for less

than 0.5 sec => actuator enters teach-in mode, the LED in the

actuator lights

2. Press and hold the configuration pushbutton with a screwdriver

until LED has flashed 5 times

3. The actuator leaves teach-in mode automatically after a few seconds

5. Configure a router CROU-00/01 in Basic-Mode

1. If there is no RF connection between push button

and an actuator, an additional router can be

configured to extend range.

2. To assign a push button to a router:-

a) Press the router configuration pushbutton with a

screwdriver for less than 0.5 sec => router enters

teach-in mode, the LED in the router is on

b) Press the selected pushbutton for less than 0.5 s

c) LED in the router flashes 20x for confirmation

d) Press the router configuration pushbutton with a

screwdriver for less than 0.5 sec => router leaves

teach-in mode

3. Press the actuator configuration pushbutton with

a screwdriver for less than 0.5 sec => actuator

enters teach-in mode. Note the LED in the router

should be off i.e. not in (teach-in mode)

4. Press the Push button and the command is now sent to the router and from there forwarded to the actuator.The

LED in the actuator flashes twice for confirmation.

5. Finally press the configuration pushbutton with a screwdriver for less than 0.5 sec => actuator leaves teach-in

mode

6. Configure two routers CROU-00/01 in Basic-Mode

1. If the range of a single router is not sufficient, a

second one can be added to extend RF range

further

2. Assign a push button to first router as detailed in

section 5 above.

3. Assign second router to push button in the exact

same manner as the first.

4. Press the actuator configuration pushbutton with a

screwdriver for less than 0.5 sec => actuator enters

teach-in mode. Note the LED in the both routers

should be off i.e. not in (teach-in mode)

5. Press the push button and the command is sent to

the routers and from there forwarded to the

actuator. LED in the actuator flashes twice for

confirmation.

6. Finally press the configuration pushbutton with a

screwdriver for less than 0.5 sec => actuator leaves

teach-in mode

Affixing date of CE mark:

2012

Doc.Id.:

F9401, F9402, F9404

Heinz Ursprunger Friedrich Schröder

Director Product Line

Director Quality

& Marketing Management & EHS

Declaration of Conformity

We, EATON Industries (Austria) GmbH

3943 Schrems, Eugenia 1

Austria

declare that product (family)

Eaton - MEM switch module,

F9401, F9402, F9404

(the declaration of conformity applies to all

listed types within our actual product catalog)

provided that it is installed, maintained and used in the

application intended for, with respect to the relevant manufacturers

instructions, installation standards and “good engineering practices”

complies with the provisions of Council directive(s):

EMC Directive 2004/108/EC

Radio and Telecommunications Terminal Equipment 99/05/EC

based on compliance with European standard(s):

EN301489-3 V1.6.1, EN300220-2 V2.4.1, EN50491-5-1/10,

EN50491-5-2/10, EN60950-1/06 + A11/09 + A1/10 + A12/11 +A2/13,

EN62479/10

01.12.2014

Eaton xComfort MEM F940x Operating instructions

Eaton xComfort MEM F940x Operating instructions

Eaton xComfort MEM F940x Operating instructions

Related papers

Other documents