Home Decorators Collection YG475-BN Operating instructions

Brand: Home Decorators Collection

Model: YG475-BN

Category: Household fans

Type: Operating instructions

USE AND CARE GUIDE

Questions, problems, missing parts? Before returning to the store,

call Home Decorators Collection Customer Service

8 a.m. - 6 p.m., EST, Monday-Friday

1-800-986-3460

HOMEDEPOT.COM/HOMEDECORATORS

THANK YOU

TRENTINO II 60 IN. CEILING FAN

Item #1000053049

Model #YG475-BN

Table of Contents

Table of Contents ..........................................................

Safety Information .........................................................

Warranty .........................................................................

Pre-Installation ..............................................................

Tools Required .........................................................................

Hardware Included ..................................................................

Package Contents ....................................................................

Dual Mounting Instructions ......................................................

Installation .....................................................................

Assembly ........................................................................

Standard Ceiling Mounting .......................................................

Close-to-Ceiling Mounting .....................................................

Hanging the Fan ....................................................................

Attaching the Fan Blades .......................................................

Installing the Light Kit ............................................................

Operation .....................................................................

Pull Chain Operating Instructions ..........................................

Reverse Switch Operating Instructions ..................................

Care and Cleaning .......................................................

Troubleshooting ..........................................................

Service Parts ...............................................................

Safety Information

3 HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

1. To reduce the risk of electric shock, ensure electricity has

been turned off at the circuit breaker or fuse box before

beginning.

2. All wiring must be in accordance with the National Electrical

Code “ANSI/NFPA 70-1999” and local electrical codes.

Electrical installation should be performed by a qualiﬁed

licensed electrician.

3. The outlet box and support structure must be securely

mounted and capable of reliably supporting a minimum of 50

lbs. Use only UL-listed outlet boxes marked “FOR FAN

SUPPORT.”

4. The fan must be mounted with a minimum of 7 ft. clearance

from the trailing edge of the blades to the ﬂoor.

5. Avoid placing objects in the path of the blades.

6. To avoid personal injury or damage to the fan and other

items, be cautious when working around or cleaning the fan.

7. Do not use water or detergents when cleaning the fan or fan

blades. A dry dust cloth or lightly dampened cloth will be

suitable for most cleaning.

8. After making electrical connections, spliced conductors

should be turned upward and pushed carefully up into the

outlet box. The wires should be spread apart with the

grounded conductor and the equipment-grounding conductor

on one side of the outlet box and ungrounded conductor on

the other side of the outlet box.

9. All setscrews must be checked and retightened where

necessary before installation.

WARNING: To reduce the risk of electrical shock or ﬁre, do

not use this fan with any solid-state fan speed control device.

It will permanently damage the electronic circuitry.

WARNING: Do not insert foreign objects between rotating

fan blades.

WARNING: To reduce the risk of ﬁre, electric shock or

personal injury, mount the fan to the outlet box marked

acceptable for fan support with the screws provided with the

outlet box.

CAUTION: To reduce the risk of personal injury, use only

the screws provided with the outlet box.

SPECIFICATIONS

TOOLS REQUIRED

Phillips

screwdriver

Electrical

tape

Wire

stripper

Flat blade

screwdriver

Step

ladder

Warranty

Pre-InstallationPre-Installation

We warrant the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period

of lifetime after the date of purchase by the original purchaser. We also warrant that all other fan parts, excluding any glass or acrylic

blades, to be free from defects in workmanship and material at the time of shipment from the factory for a period of two years after the

date of purchase by the original purchaser. We agree to correct such defects without charge or at our option replace with a comparable or

superior model if the product is returned. To obtain warranty service, you must present a copy of the receipt as proof of purchase. All

costs of removing and reinstalling the product are your responsibility. Damage to any part such as by accident, misuse, improper installa-

tion or by afﬁxing any accessories, is not covered by this warranty. Because of varying climatic conditions this warranty does not cover

any changes in brass ﬁnish, including rusting, pitting, corroding, tarnishing or peeling. Brass ﬁnishes of this type give their longest useful

life when protected from varying weather conditions. A certain amount of “wobble” is normal and should not be considered a defect.

Servicing performed by unauthorized persons shall render the warranty invalid. There is no other express warranty. We hereby disclaim

any and all warranties, including but not limited to those of merchantability and ﬁtness for a particular purpose to the extent permitted by

law. The duration of any implied warranty which cannot be disclaimed is limited to the time period as speciﬁed in the express warranty.

Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you. The retailer shall

not be liable for incidental, consequential, or special damages arising out of or in connection with product use or performance except as

may otherwise be accorded by law. Some states do not allow the exclusion of incidental or consequential damages, so the above

exclusion or limitation may not apply to you. This warranty gives speciﬁc legal rights, and you may also have other rights which vary from

state to state. This warranty supersedes all prior warranties. Shipping costs for any return of product as part of a claim on the warranty

must be paid by the customer.

Contact the Customer Service Team at 1-800-986-3460 or visit www.HOMEDEPOT.COM/HOMEDECORATORS

60 in.

Low

Medium

High

120

Fan size

Watts

RPM

CFM

Speed

Volts

Amps

2.89 ft.

N.W.

G.W.

C.F.

0.36

0.54

0.81

125

187

4091

6480

10272

16.71 kgs

(36.77 lbs)

18.76 kgs

(41.28 lbs)

Pre-Installation (continued)

HARDWARE INCLUDED

Plastic wire nut (not to scale)

Canopy mounting bracket screw with lock washer (preassembled)

Clevis pin (preassembled)

Cotter pin (preassembled)

Setscrew (preassembled)

Cross pin (preassembled)

Collar setscrew (preassembled)

Collar mounting screw with lock washer (preassembled)

Blade arm screw with lock washer (preassembled)

Switch housing mounting screw (preassembled)

Light kit mounting screw (preassembled)

13 watt compact ﬂuorescent bulb (not to scale)

Pull chain and fob (not to scale)

Switch housing cover (not to scale)

Part

Description

Quantity

NOTE: Hardware shown to actual size unless noted

otherwise in the table below.

5 HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

PACKAGE CONTENTS

Pre-Installation (continued)

Part

Description

Fan motor assembly

Blade

Blade arm

Switch housing

Light kit

Glass shade

Quantity

Part

Quantity

Description

Mounting bracket (preassembled)

Canopy ring (preassembled)

Canopy

Canopy bottom cover (preassembled)

Hanger ball/downrod assembly

Coupling cover

Pre-Installation (continued)

DUAL MOUNTING INSTRUCTIONS

This ceiling fan is supplied with two types of hanging assemblies: the

standard ceiling installation using the downrod with ball and socket

mounting, and the "close-to-ceiling" mounting. The "close-to-ceiling"

mounting is recommended in rooms with less than 8 ft. ceilings or in

areas where additional space is desired from the ﬂoor to the fan blades.

When using the standard downrod installation, the distance from the

ceiling to the bottom of the fan blades will be approximately 12 in. The

"close-to-ceiling" installation reduces the distance from the ceiling to the

bottom of the fan blades to approximately 9 in.

Once you have decided which ceiling installation you will use, refer to the

corresponding sections and procedures during the assembly period.

Where necessary, each section of the instructions will note the different

procedures to follow for the two types of installation.

Standard Ceiling Mounting

Close-to-Ceiling Mounting

7 HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

To hang your fan where there is an existing ﬁxture but no ceiling

joist, you may need an installation hanger bar (PP) (not included)

as shown above.

If your ceiling fan does not have an existing UL-listed mounting

box, then install one using the following instructions:

□ Disconnect the power by removing the fuses or turning off

the circuit breakers.

□ Secure the outlet box (OO) (not included) directly to the

building structure. Use appropriate fasteners and materials

(not included). The outlet box and its bracing must be able

to fully support the weight of the moving fan (at least 50

lbs.). Do not use a plastic outlet box.

The illustrations below show three different ways to mount the

outlet box (OO) (not included).

Installation

MOUNTING OPTIONS

WARNING: To reduce the risk of ﬁre, electric shock, or

personal injury, mount the fan to an outlet box marked

acceptable for fan support using the screws provided with the

outlet box. An outlet box commonly used for the support of

lighting ﬁxtures may not be acceptable for fan support and

may need to be replaced. If in doubt, consult a qualiﬁed

electrician.

NOTE: You may need a longer downrod to maintain proper

blade clearance when installing on a steep, sloped ceiling.

The maximum angle allowable is 18° away from horizontal. If

the canopy (C) touches the hanger ball/downrod assembly (E),

then remove the decorative canopy bottom cover (D) and turn

the canopy (C) 180° before attaching the canopy (C) to the

mounting bracket (A).

1Preparing the canopy 2Preparing the motor

□ Remove the canopy ring (B) from the canopy (C).

□ Remove the two non-slotted mounting bracket screws

(BB) from the canopy (C), and loosen the slotted

mounting bracket screws (BB) on the canopy (C).

□ Remove the canopy (C) from the mounting bracket (A)

by turning the canopy (C) counterclockwise.

3Assembling the fan

Assembly — Standard Ceiling Mounting

9 HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

□ Remove the clevis pin (CC) and cotter pin (DD), and

loosen the two collar setscrews (GG) from the motor

collar.

□ Take out the setscrew (EE) located in the hanger ball

(QQ), lower the hanger ball and remove the cross pin

(FF). Remove the hanger ball (QQ) from the the

hanger ball/downrod assembly (E).

□ Carefully feed the motor wires up through the

downrod (RR). Thread the downrod (RR) into the

collar.

□ Align the holes and replace the cotter pin (DD) and

clevis pin (CC). Tighten the two collar setscrews (GG).

□ Slip the coupling cover (F), canopy ring (B), and

canopy (C) onto the downrod (RR).

□ Carefully reinstall the hanger ball (QQ) onto the

downrod (RR), being sure that the cross pin (FF) is in

the correct position, the setscrew (EE) is tightened

and the wires are not twisted.

WARNING: Failure to properly install the cotter pin (DD)

could result in the fan loosening and possibly falling.

NOTE: If a longer downrod (not included) is needed, take

out the screw located in the hanger ball (QQ), lower the

hanger ball (QQ) and remove the pin (FF). Remove all three

pieces from the downrod and assemble them onto the new

longer downrod before proceeding to the downrod installa-

tion. B

Assembly — Close-to-Ceiling Mounting

3Assembling the fan

Preparing the motorPreparing the canopy

□ Remove three of the six collar mounting screws with

lock washers (HH) (every other one) from the collar

on top of the fan motor assembly (G).

WARNING: Failure to completely tighten the three collar

mounting screws (HH) could result in the fan becoming loose

and possibly falling.

□ Remove the mounting bracket (A) from the canopy (C)

by loosening the four canopy mounting bracket

screws (BB) on the top of the canopy (C). Remove the

two non-slotted canopy mounting bracket screws

(BB) and loosen the slotted canopy mounting bracket

screws (BB).

□ Remove the canopy bottom cover (D) from the

canopy (C).

□ Make sure the slot openings of the canopy ring (B)

are on top, and then proceed to place the canopy ring

(B) and canopy (C) over the collar at the top of the fan

motor assembly (G).

□ Align the mounting holes in the bottom of the canopy

bly (G). Fasten using the three collar mounting screws

with lock washers (HH) previously removed.

□ Tighten the collar mounting screws (HH) securely.

Assembly — Hanging the Fan

4Attaching the fan to the

electrical box

5b5a Hanging instructions for

standard mounting

Hanging instructions for

close-to-ceiling mounting

□ Pass the 120-volt supply wires through the center

hole in the mounting bracket (A).

□ Attach the mounting bracket (A) on the outlet box

(OO) by sliding the mounting bracket (A) over the

screws provided with the outlet box. When using

“close-to-ceiling” mounting, it is important that the

mounting bracket (A) be level. If necessary, use

leveling washers (not included) between the mount-

ing bracket (A) and the outlet box (OO). Note that the

ﬂat side of the mounting bracket (A) is toward the

outlet box (OO).

□ Securely tighten the two mounting screws.

WARNING: To reduce the risk of ﬁre, electric shock or

other personal injury, mount the fan only to an outlet box or

supporting system marked acceptable for fan support and

use the mounting screws provided with the outlet box.

WARNING: The tab in the ring must rest in the groove of

the hanger ball (E). Failure to properly seat the tab in the

groove could cause damage to the wiring.

WARNING: The hook is only to hold the fan while attaching

wiring. Failure to hang as instructed may result in the tab

breaking causing the fan to fall. The hook must pass from the

inside to the outside of the canopy.

□ Carefully lift the fan motor assembly (G) up to the

mounting bracket (A) and seat the hanger ball (E) in

the mounting bracket (A) socket. Make sure the tab

on the mounting bracket (A) socket is properly seated

in the groove in the hanger ball (E). This will help to

balance the ceiling fan.

□ Carefully lift the fan motor assembly (G) up to the

mounting bracket (A) and hang the fan on the hook

provided using one of the holes at the outer rim of the

canopy (C).

11 HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

6Making the electrical

connections

Assembly — Hanging the Fan (continued)

Blue

Black

Green

White

Black

Ground

conductor

White

If you feel you do not have enough electrical wiring

knowledge or experience, have your fan installed by a

licensed electrician.

Follow the steps below to connect the fan to your

household wiring. Use the plastic wire nuts (AA) with your

fan. Secure the plastic wire nuts (AA) with electrical tape.

Make sure there are no loose strands or connections.

□ Connect the ground conductor of the 120V supply

(this may be a bare wire or a wire with green colored

insulation) to the green ground lead(s) of the fan.

When using standard ceiling mounting, there are two

green grounding leads: one from the mounting

bracket (A) and one from the hanger ball/downrod

assembly (E). When using “close-to-ceiling”

mounting, there is only one green ground lead from

the mounting bracket (A) since the hanger

ball/downrod assembly (E) is not used.

□ Connect the fan motor white wire to the supply white

(neutral) wire using a plastic wire nut (AA).

□ Connect the fan motor black wire and the blue wire to

the supply black (hot) wire using a plastic wire nut

(AA).

□ Turn the wire nut connections upward, spreading

them apart so the green (ground) will be on one side

of the outlet box (OO) and the white, black and blue

wire will be on the other side. Carefully tuck the

connections up into the outlet box (OO).

WARNING: Check to see that all connections are tight,

including ground, and that no bare wire is visible at the wire

nuts (except for the ground wire).

WARNING: To reduce the risk of ﬁre or electric shock, do

not use this fan with any solid-state speed control device.

WARNING: To avoid possible electrical shock, be sure

electricity is turned off at the main fuse box before wiring.

Assembly — Hanging the Fan (continued)

7a Standard ceiling mounting 7b Close-to-ceiling mounting

WARNING: The locking slots of the canopy (C) are provided

only as an aid to mounting. Do not leave the fan assembly

unattended until all four canopy mounting bracket screws

(BB) are engaged and ﬁrmly tightened.

WARNING: Make sure the tab on the mounting bracket (A)

properly sits in the groove in the hanger ball (E) before

attaching the canopy (C) to the mounting bracket (A) by

turning the canopy (C) until it drops into place.

WARNING: Locking slots of the canopy (C) are provided

only as an aid to mounting. Do not leave the fan assembly

unattended until all four canopy screws (BB) are engaged and

ﬁrmly tightened.

□ Slide the canopy (C) up to the ceiling. Make sure you

have placed the wires safely into the outlet box (OO).

□ Secure the canopy (C) to the mounting bracket (A)

with the four canopy mounting bracket screws and

lock washers (BB) included with your fan.

□ Remove the fan from the hook on the mounting

bracket (A).

□ Secure the canopy (C) to the mounting bracket (A)

with the four mounting bracket screws with lock

washers (BB) provided.

13 HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

Assembly — Attaching the Fan Blades

8Attaching the blades to

the blade arms

IUU

WARNING: Failure to properly seat the blades (H) on the

blade arms (I) and engage in the spring locking mechanism

(UU) could result in the fan blades (H) loosening and possibly

falling.

□ Hold the blade (H) with hands close to the blade arm

(I), align the key-slot holes (SS) with the blade arm

posts (TT) and press the blade down ﬁrmly. Ensure

the key-slot holes (SS) are properly seated on the

blade arm posts (TT).

□ Firmly slide the blade (H) away from the blade arm (I)

until the blade (H) engages in the spring locking

mechanism (UU). Make sure the spring of the spring

locking mechanism (UU) is upward and the butt of the

spring locking mechanism (UU) is against the edge of

the blade.

To install the blade to the blade arm:

□ Press down the spring locking mechanism (UU) to

release the blade (H) from the blade arm (I). Slide the

blade (H) toward the blade arm (I) until the blade (H)

disengages from the spring locking mechanism (UU),

carefully push the blade (H) up to detach from the

blade arm (I).

To detach the blade from the blade arm:

Assembly — Attaching the Fan Blades

Fastening the blade

assemblies to the motor

WARNING: To reduce the risk of personal injury, do not

bend the blade arms (I) while installing, balancing the blades

(H), or cleaning the fan. Do no insert foreign objects between

rotating fan blades (H).

15 HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

□ Fasten the blade assemblies to the fan motor

assembly (G) by lining up the slots of the motor (WW)

with the tabs (XX) on the blade arms (I).

□ Tighten the two blade arm screws with lock washers

(II) already installed in the blade arms (I).

□ Repeat this procedure for the remaining blade arms

(I).

9Removing the motor

support plate

□ The fan motor assembly (G) is shipped with motor

support plate (VV) to prevent movement during

transportation. Remove the motor support plate (VV)

from the fan motor assembly (G) and discard prior to

attaching the blade arms.

Assembly — Installing the Light Kit

AAA

Attaching the switch housing

to the mounting ring

□ Remove one of the three switch housing mounting

screws (JJ) from the mounting ring (YY) and loosen

the other two screws (JJ). (Do not remove.)

□ While holding the switch housing (J) under the fan

motor assembly (G), snap together the wire connec-

tion plugs (ZZ).

□ Place the key holes in the switch housing (J) over the

two screws (JJ) previously loosened from the

mounting ring (YY). Turn the switch housing (J) until

the switch housing (J) locks in place at the narrow

section of the key holes.

□ Securely tighten the two mounting plate screws (JJ)

previously loosened and the one (JJ) previously

removed.

CAUTION: Before starting installation, disconnect the

power by turning off the circuit breaker or removing the fuse

at the fuse box. Turning power off using the fan switch is not

sufﬁcient to prevent electric shock.

NOTE: If you do not wish to install the light kit, skip steps

11 through 13 and proceed to step 14.

Attaching the light kit to

the switch housing

□ Remove the three light kit mounting screws (KK) from the

light kit (K) and keep these screws.

□ While holding the light kit (K) under your fan motor

assembly (G), locate two single white and blue wires in

the switch housing labeled "FOR LIGHT". Make the

polarized plug connections (AAA):

- White to white

- Blue to black

□ Carefully push all wires back into the switch housing.

Install the light kit (K) onto the switch housing with the

three light kit mounting screws (KK) provided. Be sure to

tighten all screws.

□ Installing the glass shade (L) into the glass holder by

insert the slot (BBB) from the glass shade (L) to the

tab (CCC) in the glass holder and turning glass shade

(L) clockwise until snug. Do not overtighten.

□ Install three 13 watt compact ﬂuorescent bulbs (LL)

(included).

CAUTION: Before starting installation, disconnect the

power by turning off the circuit breaker or removing the fuse

at the fuse box. Turning power off using the fan switch is not

sufﬁcient to prevent electric shock.

Assembly — Installing the Light Kit (continued)

13 Installing the light bulb

and glass shade

17 HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

BBB

CCC

□ Install the switch housing cover (NN) to the light kit

mounting plate (J) with switch housing cover screws

(DDD) provided.

14 Installing the fan without the

light kit (optional)

DDD J

Operation

PULL CHAIN OPERATING INSTRUCTIONS

Install two pull chains and fobs (MM) onto the pull chains located

in the light kit (K). Turn on the power and check the operation of

the fan.

The pull chain controls the fan speed as follows:

1 pull - High, 2 pulls - Medium, 3 pulls - Low, and 4 pulls - Off.

Speed settings for warm or cool weather depend on factors such

as the room size, ceiling height, and number of fans.

The light pull chain controls the light kit: "ON" and "OFF".

NOTE: Wait for the fan to stop before reversing the direction

of the blade rotation.

REVERSE SWITCH OPERATING INSTRUCTIONS

The reverse switch is located on the surface of the switch housing.

Slide the switch to the left for warm weather operation. Slide the

switch to the right for cool weather operation.

Warm weather - (Counterclockwise Direction) A downward air ﬂow

creates a cooling effect. This allows you to set your air conditioner

on a warmer setting without affecting your comfort.

Cool weather - (Clockwise Direction) An upward air ﬂow moves

warm air off the ceiling. This allows you to set your heating unit on

a cooler setting without affecting your comfort.

Care and Cleaning

Troubleshooting

□ Check the support connections, brackets, and blade

attachments twice a year. Make sure they are secure.

Because of the fan’s natural movement, some

connections may become loose over time. It is not

necessary to remove the fan from the ceiling.

□ Clean your fan periodically. Use only a soft brush or

lint-free cloth to avoid scratching the ﬁnish. The plating is

sealed with a lacquer to minimize discoloration or

tarnishing.

□ (Optional) Apply a light coat of furniture polish to the wood

blades.

□ (Optional) Cover small scratches with a light application of

shoe polish.

□ Use water when cleaning. Water could damage the motor,

or the wood, or possibly cause an electrical shock.

□ Apply oil to your fan or motor. The motor has

permanently-lubricated sealed ball bearings.

Do not

WARNING: Make sure the power is off at the electrical

panel box before you attempt any repairs. Refer to the section

“Making the Electrical Connections” on page 12.

19 HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

Problem

Solution

□ Check the main and branch circuit fuses or breakers.

□ Check the line wire connections to the fan and switch wire connections in the switch housing.

□ Make sure all motor housing screws are snug.

□ Make sure the screws that attach the fan blade arm to the motor hub are tight.

□ Make sure wire nut connections are not rattling against each other or the interior wall of the switch

housing.

□ Allow a 24-hour "breaking-in" period. Most noises associated with a new fan disappear during this

time.

□ If using the ceiling light kit, check the light bulb is secure.

□ Make sure there is a short distance from the ceiling to the canopy. It should not touch the ceiling.

□ Make sure your ceiling box is secure and rubber isolator pads are used between the mounting bracket

and outlet box.

The fan will not start.

The fan sounds noisy.

Troubleshooting (continued)

Problem

Solution

The fan wobbles.

□ Verify that all blades and blade bracket screws are secure (most fan wobble problems are caused by

loose parts). Once the fan is properly installed, run the ceiling fan for 10 minutes to let the fan

self-adjust.

If wobble occurs after running the fan for 10 minutes, verify blade level using the following process:

- Select a point on the ceiling above the tip of one of the blades, then select any fan blade and

measure from the center of the selected blade to the point on the ceiling. Rotate the fan until the next

blade is positioned and repeat the measurement using the same point from the ceiling for every blade.

Measurement deviations should be within 1/8 in..

- If all deviations are less than 1/8 in. and the fan continues to wobble, please call Customer Service

(1-800-986-3460) to order a complimentary Blade Balancing Kit.

- If deviation is greater than 1/8 in. , please call Customer Service (1-800-986-3460) to order

complimentary replacements of your brackets.

Page is loading ...

Home Decorators Collection YG475-BN Operating instructions

Brand: Home Decorators Collection

Model: YG475-BN

Category: Household fans

Type: Operating instructions

Download PDF

report

Home Decorators Collection YG475-BN Operating instructions

Home Decorators Collection YG475-BN Operating instructions

Related papers

Other documents