SENSORNET/MANCHESTER DISTRIBUTION PANEL 8200-0712-01, REV. E
INSTALLATION GUIDE
1 of 5
SensorNet/Manchester
Distribution Panel
Installation Guide
Figure 1. SensorNet/Manchester Distribution
Panel
ADACSNETD/ADACSNETDP
About this Guide
This installation guide explains how to install the
SensorNet/Manchester Distribution Panel.
If you need assistance...
Contact your Sales Representative.
Warning and Cautions
WARNING: RISK OF ELECTRIC
SHOCK! Disconnect AC power to
the panel.
CAUTION-Electrostatic Sensitive
Device: Follow proper handling
procedures to prevent component failure.
© 2008 Sensormatic Electronics Corp.
About the Product
The SensorNet/Manchester Distribution Panel
provides signal amplification for the SensorNet and
Manchester multi-point dome control
communications and has 16 secondary device
ports (two connectors per port) to accommodate
home-run dome wiring or multiple daisy-chained
connections to domes, J-boxes, or other
distribution panels.
Each of the ports has an LED that indicates data is
being received. Since Manchester communication
is simplex (one-way) communication, received data
is never present on the 16 secondary device ports;
therefore, the LEDs for ports 1, 2, and 3 will be
constantly ON with ports 4 through 16 OFF to
indicate the unit is in Manchester mode.
Figure 2. Distribution Panel components
Note: The Noise Indicator may signal improper line
termination, line noise, packets cut short, or other
false carrier detection situations whenever a
too-short packet fragment is detected.
Output Data Connectors,
LEDS, and Switches
Power
Connecto
r
12–30V AC/DC
Noise Indicator
Host Connectors,
LEDs, and Switches
SW1 DIP Switches
SENSORNET/MANCHESTER DISTRIBUTION PANEL 8200-0712-01, REV. E
INSTALLATION GUIDE
2 of 5
Installation
Parts
Install kit 0352-0331-01, used with the 0404-0383-01
distribution panel. It includes grounding hardware.
Part
Qty
Part Number
User Guide, Video Sys Comm
Protocols & Cable Networks
1
8000-2573-19
Con,p,Eur,3.5,22-16g,1x3p
34
2109-0510-03
Con,p,Eur,.2c,28-12g,3p,orange
1
2109-0254-02
Cbl,3c,18g,16x30,pvc,cm
16.50
6002-0024-01
Lbl,blnk,pap,therm,3.5x3,wh,rl
1
2450-0008-01
Scr,m,php,st,z,6-32x1/4
1
2804-7106-06
Wsh,int th,#6,st,z
1
2845-6300
Nut,hx,ss,6-32
1
2836-0001-03
Tm,spade,#6,22-16aw
2
2141-0027-01
Required Tools
• Screwdriver
Rack Installation
1. Position the distribution panel in the desired
equipment rack location.
2. Using the appropriate screws, secure the
distribution panel to the equipment rack.
3. For effective surge protection, ground the
enclosure by rack mounting to a grounded rack
or with a conductor from the enclosure to
ground. Ensure metal-to-metal contact.
Configuration Considerations
SW1 Switch Settings
Pos. 0 Setting 1 Setting
1
50µs Turnaround
Time
(1)
> 50µs Turnaround
Time
(1)
2 Manchester SensorNet
3 Not used Not used
4 Not used Not used
5 Not used Not used
6 Not used Not used
7 LED Test Mode
(2)
Normal Operation
8
State Machine Test
Mode
(3)
Normal Operation
Notes:
(1)
Turnaround time: Normally, SW1 position 1 is
set to ‘1.’ Setting SW1 position 1 to ‘0’ might be
beneficial for some legacy domes at a short
distance.
(2)
LED functional operation test mode: To test, set
SW1 position 7 to ‘0.’ All LED indicators should
turn on, except for the noise indicator.
(3)
State machine test mode: For engineering test
only. Set SW1 position 8 to ‘1’.
Termination Switches
There are termination switches on each of the 16
secondary device ports and the two Host ports.
They are recessed so they cannot be accidentally
tripped. Set a termination switch to terminate if it is
located at the end of the line. Set the switch to not
terminate if multiple wires connect to the port. This
practice is similar to video termination rules in
which terminators are only located at the end of a
wire.
SENSORNET/MANCHESTER DISTRIBUTION PANEL 8200-0712-01, REV. E
INSTALLATION GUIDE
3 of 5
Specifications
Model Numbers
ADACSNETD ................ No external power module
ADACSNETDP..... Includes external power module
Electrical
Power Source......................External power module
Transformer:
North American (can power 3 units)..... 27VA
International (can power 5 units).......... 45VA
Input.........................12–30V, DC or AC, (50–60Hz)
Certified Limited Power Source
NEC Class 2
Isolation not required
Power Consumption ..........................................8VA
Indicators:
Power-On/Heartbeat ........................ Green LED
Noise Detect.........................................Red LED
Host A and B Receive Data .............Yellow LED
Channels 1–16 Receive Data ..........Yellow LED
Protection ................... Internal primary current fuse
Inrush limiting
DC Isolation
Cable to transformer............................... 5m (16.5ft)
18 AWG (0.823mm
2
), 3-conductor
Input Connector... Euro-style 3-pin removable plug
5.06mm (0.2in.) terminal block
Surge Protection.............. Transguard rated at 60V,
250A, 1.5 Joules
Gas discharge tube impulse rated at 10kA
Design Tolerance:
Input voltage minimum 11V DC or AC without
drop out
Input voltage >36V DC or AC may damage
equipment
Input frequency..................................... 47–63Hz
Allowable drop out....................................150ms
Power connector pin assignments:
Pin Label Notes
1 and 3
12V – 30V
AC/DC
Connect 12–30V AC or
DC power to these pins
in any polarity
2 Ground
Used for surge
protection and data line
shields
Surge Protection
SensorNet/Manchester Ports
Transient Voltage Suppressors (TVS):
Break Down Voltage.........................7.6–9.3Vdc
Peak Current.................................................40A
Capacitance............................... 2000pf @ 1kHz
Gas discharge tube impulse rated at:
DC Break Down Voltage...........................90Vdc
Insulation Resistance ........................ 10,000MΩ
Capacitance........................................... 2pf Max
8/20µs Impulse Discharge Current.............10kA
Ten 8/20µs Impulses Discharge Current......5kA
Isolation transformer coupled ..................2000Vrms
PTC re-settable fuse protects transformer
Mechanical
Overall dimensions (LxWxD) ........... 481x87x34mm
(18.9 x 3.4 x 1.3in.)
Body length ....................................446mm (17.6in.)
Weight........................................... 0.75kg (1.66 lbs)
Mounting: EIA-310-D 19in. Electronic Racks (2 RU)
IEC 60297-1 482.6mm Electronic Racks (2 RU)
Compatibility
Compatible with all versions of American Dynamics
SpeedDomes, Manchester receiver drivers,
J-Boxes, and control systems using SensorNet or
Manchester protocols
Environmental
Operating Temperature ....................... -10° to 50°C
(14° to 122°F)
Storage Temperature........................... -40° to 70°C
(-40° to 158°F)
Relative Humidity ............0 to 95% non-condensing
SENSORNET/MANCHESTER DISTRIBUTION PANEL 8200-0712-01, REV. E
INSTALLATION GUIDE
4 of 5
Data Communication
Specification SensorNet Manchester
Address Range 1 to 254 1 to 64
Bit Rate 230.4kbps 31kbps
Network Distance
1km (3300ft) per cable segment if
repeaters are used
1.5km (5000ft) per cable segment if
repeaters are not used
1.5km (5000ft)
Maximum Loads 32 per cable segment 3 per run
Cable Segment
Repeaters
SensorNet Junction boxes and
distribution panels
Distribution panels
Topologies Daisy Chain, Backbone, or Star Daisy Chain
Transmission
Medium
Single, non-polarized, unshielded
twisted pair UTP 22AWG (0.326mm
2
)
Single twisted pair 18AWG (0.823mm
2
)
(Belden 8760), polarized, shielded
Connector
Euro-style 3-pin removable plug
3.5mm (0.14in) terminal block, shield
not used
Euro-style 3-pin removable plug
3.5mm (0.14in) terminal block
Connector Pin
Assignments
Pin 1 .......................S+ (Orange wire)
Pin 2 ........................ S– (Yellow wire)
Pin 3 ..........Ground (Shield not used)
Pin 1 ...................................... S+ (Black wire)
Pin 2 ......................................S– (White wire)
Pin 3 ............................ Ground (Shield used)
Terminating Resistor 120Ω, switch selectable 120Ω, switch selectable
Physical Layer RS-485, transformer-isolated, 2-wire RS-485, transformer-isolated, 2-wire
Data Encoding FM-0 Manchester
Link Layer Framing SDLC/HDLC Proprietary
Link Layer Channel Bi-directional, half-duplex Simplex
Collision Avoidance
Polling by primary host controller
device
N/A
Application Protocol Proprietary Proprietary
Host Controller
Devices
ADMPCPU, ADTT16E primary
Touch Tracker
®
, MegaPower
®
48
Plus, MegaPower LT, ADACSNET
SensorNet USB module, and previous
AD SensorNet host/controller
products
ADMPCPU, AD2091, MegaPower 48 Plus,
and previous AD SensorNet host controller
products
Secondary Devices
Domes, Distribution Panels, Junction
Boxes, Secondary Touch Tracker,
and SensorNet I/O Unit
Domes
Notes:
• The host input ports will be used in sequence whenever the previous input port is not receiving data.
• When used in a dual MegaPower CPU system, the HOST A port connects to one CPU, and the HOST B port
connects to the other CPU to support hot-switching capability.
SENSORNET/MANCHESTER DISTRIBUTION PANEL 8200-0712-01, REV. E
INSTALLATION GUIDE
5 of 5
Declarations
Regulatory Compliance
EMC............................................... 47 CFR, Part 15
ICES-003
EN 55022
Immunity................................................ EN50130-4
Safety ....................................................UL 60950-1
CSA C22.2.60950-1
EN 60950-1
IEC 60950-1
REGULATORY PRODUCT NAME:
TYPE: ADVDB
FCC COMPLIANCE: This equipment complies with Part 15
of the FCC rules for Class A digital devices when installed and
used in accordance with the instruction manual. Following
these rules provides reasonable protection against harmful
interference from equipment operated in a commercial area.
This equipment should not be installed in a residential area as
it can radiate radio frequency energy that could interfere with
radio communications, a situation the user would have to fix at
their own expense.
EQUIPMENT MODIFICATION CAUTION: Equipment
changes or modifications not expressly approved by
Sensormatic Electronics Corporation, the party responsible for
FCC compliance, could void the user's authority to operate the
equipment and could create a hazardous condition.
See “
About the Product” on page 1.
Other Declarations
Thank you for using American Dynamics products. We
support our products through an extensive and worldwide
network of dealers. The dealer, through whom you originally
purchased this product, is your point of contact if you have a
need for service or support. Our dealers are fully empowered
to provide the very best in customer service and support.
Dealers should contact American Dynamics at
(800) 507-6268 or (561) 912-6259 or on the web at
www.americandynamics.net.
WARRANTY DISCLAIMER: Sensormatic Electronics
Corporation makes no representation or warranty with respect
to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular
purpose.
NOTICE: The information in this manual was current when
published. The manufacturer reserves the right to revise and
improve its products. All specifications are therefore subject to
change without notice.
LIMITED RIGHTS NOTICE: For units of the Department
of Defense, all documentation and manuals were developed at
private expense and no part of it was developed using
Government Funds. The restrictions governing the use and
disclosure of technical data marked with this legend are set
forth in the definition of “limited rights” in paragraph (a) (15)
of the clause of DFARS 252.227.7013. Unpublished - rights
reserved under the Copyright Laws of the United States.
TRADEMARK NOTICE: American Dynamics and
Sensormatic are trademarks or registered trademarks of
Sensormatic Electronics Corporation. Other product names
mentioned herein may be trademarks or registered trademarks
of Sensormatic or other companies.
COPYRIGHT: Under copyright laws, the contents of this
manual may not be copied, photocopied, reproduced,
translated or reduced to any electronic medium or machine-
readable form, in whole or in part, without prior written
consent of Sensormatic Electronics.
WJM 01/2008
www.americandynamics.net
-
1
-
2
-
3
-
4
-
5
American Dynamics ADACSNETDP Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American Dynamics ADACSNET Installation guide
-
American Dynamics SpeedDome Optima LT Specification
-
American Dynamics SpeedDome Optima LT Installation and Service Manual
-
American Dynamics SpeedDome Ultra VII Specification
-
American Dynamics SpeedDome Optima LT Installation guide
-
American Dynamics SpeedDome Ultra Outdoor Housing ADSDUHOC User manual
-
American Dynamics IP speedDome Ultra 8 Installation and Service Manual
-
American Dynamics ADSDUHOC Installation guide
-
American Dynamics MegaPower 3200 Release 2.0 Installation guide
-
American Dynamics ADSDU822WN Specification
