ESAB 2RT Transmig Wire Feeder User manual

Brand: ESAB

Model: 2RT Transmig Wire Feeder

Category: Welding System

Type: User manual

300

Operating Manual

Revision: AB Issue Date: June 15, 2012 Manual No.: 0-5196

Operating Features:

TRANSMIG

WIRE FEEDER

2RT

WE APPRECIATE YOUR BUSINESS!

Congratulations on your new Cigweld product. We are proud

to have you as our customer and will strive to provide you with

the best service and reliability in the industry. This product is

backed by our extensive warranty and world-wide service net-

work. To locate your nearest distributor or service agency call

+1300 654 674, or visit us on the web at www.victortechnologies.com

This Operating Manual has been designed to instruct you on the correct

use and operation of your CIGWELD product. Your satisfaction with this

product and its safe operation is our ultimate concern. Therefore please

take the time to read the entire manual, especially the Safety Precau-

tions. They will help you to avoid potential hazards that may exist when

working with this product.

We have made every effort to provide you with accurate instructions,

drawings, and photographs of the product(s) while writing this manual.

However errors do occur and we apologize if there are any contained in

this manual.

Due to our constant effort to bring you the best products, we may make

an improvement that does not get reﬂ ected in the manual. If you are ever

in doubt about what you see or read in this manual with the product you

received, then check for a newer version of the manual on our website

or contact our customer support for assistance.

YOU ARE IN GOOD COMPANY!

The Brand of Choice for Contractors and Fabricators Worldwide.

CIGWELD is the Market Leading Brand of Arc Welding Products for Victor

Technologies, Inc. We are a mainline supplier to major welding industry

sectors in the Asia Paciﬁ c and emerging global markets including; Manu-

facturing, Construction, Mining, Automotive, Engineering, Rural and DIY.

We distinguish ourselves from our competition through market-leading,

dependable products that have stood the test of time. We pride ourselves

on technical innovation, competitive prices, excellent delivery, superior

customer service and technical support, together with excellence in sales

and marketing expertise.

Above all, we are committed to develop technologically advanced prod-

ucts to achieve a safer working environment for industry operators.

WARNINGS

Read and understand this entire Manual and your employer’s safety practices before installing,

operating, or servicing the equipment.

While the information contained in this Manual represents the Manufacturer’s best judgement,

the Manufacturer assumes no liability for its use.

Operating Manual Number 0-5196 for:

Cigweld Transmig 2RT Wirefeeder Part Number W3000500

Published by:

Victor Technologies, Inc.

82 Benning Street

West Lebanon, New Hampshire, USA 03784

(603) 298-5711

www.victortechnologies.com

Victor Technologies, Inc.

Reproduction of this work, in whole or in part, without written permission of the publisher is

prohibited.

The publisher does not assume and hereby disclaims any liability to any party for any loss

or damage caused by any error or omission in this Manual, whether such error results from

negligence, accident, or any other cause.

Publication Date: October 25, 2011

Revision Date: June 15, 2012

Record the following information for Warranty purposes:

Where Purchased: ____________________________________

Purchase Date: ____________________________________

Equipment Serial #: ____________________________________

TABLE OF CONTENTS

SECTION 1: ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS ............................. 1-1

1.01 Arc Welding Hazards ....................................................................................... 1-1

1.02 Principal Safety Standards .............................................................................. 1-5

1.03 Declaration of Conformity ............................................................................... 1-6

SECTION 2: INTRODUCTION ............................................................................. 2-1

2.01 How to Use This Manual ................................................................................. 2-1

2.02 Equipment Identiﬁ cation ................................................................................. 2-1

2.03 Receipt of Equipment ...................................................................................... 2-1

2.04 Symbol Chart .................................................................................................. 2-2

2.05 Description ..................................................................................................... 2-3

2.06 User Responsibility ......................................................................................... 2-3

2.07 Transportation Methods .................................................................................. 2-3

2.08 Packaged Items .............................................................................................. 2-3

2.09 Speciﬁ cations ................................................................................................. 2-4

SECTION 3: INSTALLATION OPERATION AND SETUP ................................................. 3-1

3.01 Environment ................................................................................................... 3-1

3.02 Location .......................................................................................................... 3-1

3.03 Ventilation ....................................................................................................... 3-1

3.04 Mains Supply Voltage Requirements .............................................................. 3-1

3.05 Electromagnetic Compatibility ........................................................................ 3-1

3.06 2RT Wire Feeder Controls, Indicators and Features ........................................ 3-3

3.07 Transmig 250i Power Source Controls, Indicators and Features ..................... 3-5

3.08 Advanced Features Details .............................................................................. 3-7

3.09 Wire Feeder Set Up MIG (GMAW) Welding with Gas Shielded MIG Wire ........ 3-8

3.10 Wire Feeder Set-up for MIG (FCAW) Welding with Gasless MIG Wire ............ 3-9

3.11 Attaching the Tweco Professional MIG Torch (Euro) ..................................... 3-10

3.12 Installing a Handi Spool (200mm diameter) ................................................. 3-11

3.13 Installing a Standard Spool (300mm diameter) ............................................ 3-12

3.14 Inserting Wire into the Feed Mechanism ...................................................... 3-13

3.15 Feed Roller Pressure Adjustment .................................................................. 3-14

3.16 Feed Roller Alignment ................................................................................... 3-14

3.17 Changing the Feed Roll ................................................................................. 3-15

3.18 Input And Output Wire Guide Installation ..................................................... 3-15

3.19 Wire Reel Brake ............................................................................................ 3-16

3.20 Shielding Gas Regulator Operating Instructions ........................................... 3-17

SECTION 4: BASIC WELDING GUIDE .................................................................... 4-1

4.01 MIG (GMAW/FCAW) Basic Welding Technique ............................................... 4-1

4.02 MIG (GMAW/FCAW) Welding Troubleshooting ............................................... 4-4

SECTION 5: ROUTINE SERVICE REQUIREMENTS ...................................................... 5-1

5.01 Cleaning the Welding Power Source ............................................................... 5-1

5.02 Cleaning the Feed Rolls ................................................................................... 5-2

TABLE OF CONTENTS

SECTION 6: KEY SPARE PARTS .......................................................................... 6-1

6.01 2RT Wire Feeder replacement parts ................................................................ 6-1

APPENDIX 1: OPTIONS AND ACCESSORIES ............................................................ A-1

APPENDIX 2: 2RT WIRING SCHEMATIC ................................................................. A-2

CIGWELD LIMITED WARRANTY ........................................................................ RC-2

CIGWELD TERMS OF WARRANTY – APRIL 2012 .................................................... RC-3

WARRANTY SCHEDULE – APRIL 2010 ................................................................ RC-4

GLOBAL CUSTOMER SERVICE CONTACT INFORMATION ........................................... RC-5

TRANSMIG 2RT

Manual 0-5196 1-1 GENERAL INFORMATION

1.01 Arc Welding Hazards

WARNING

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal

shocks or severe burns. The electrode and

work circuit is electrically live whenever the

output is on. The input power circuit and ma-

chine internal circuits are also live when power

is on. In semiautomatic or automatic wire

welding, the wire, wire reel, drive roll housing,

and all metal parts touching the welding wire

are electrically live. Incorrectly installed or

improperly grounded equipment is a hazard.

1. Do not touch live electrical parts.

2. Wear dry, hole-free insulating gloves and body protec-

tion.

3. Insulate yourself from work and ground using dry

insulating mats or covers.

4. Disconnect input power or stop engine before install-

ing or servicing this equipment. Lock input power

disconnect switch open, or remove line fuses so power

cannot be turned on accidentally.

5. Properly install and ground this equipment according

to its Owner’s Manual and national, state, and local

codes.

6. Turn off all equipment when not in use. Disconnect

power to equipment if it will be left unattended or out

of service.

7. Use fully insulated electrode holders. Never dip holder

in water to cool it or lay it down on the ground or the

work surface. Do not touch holders connected to two

welding machines at the same time or touch other

people with the holder or electrode.

8. Do not use worn, damaged, undersized, or poorly

spliced cables.

9. Do not wrap cables around your body.

10. Ground the workpiece to a good electrical (earth)

ground.

11. Do not touch electrode while in contact with the work

(ground) circuit.

12. Use only well-maintained equipment. Repair or replace

damaged parts at once.

13. In conﬁ ned spaces or damp locations, do not use a

welder with AC output unless it is equipped with a

voltage reducer. Use equipment with DC output.

14. Wear a safety harness to prevent falling if working

above ﬂ oor level.

15. Keep all panels and covers securely in place.

SECTION 1: ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS

WARNING

PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY.

PACEMAKER WEARERS KEEP AWAY UNTIL CONSULTING YOUR DOCTOR. DO NOT LOSE THESE INSTRUCTIONS.

READ OPERATING/INSTRUCTION MANUAL BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT.

Welding products and welding processes can cause serious injury or death, or damage to other equipment or property,

if the operator does not strictly observe all safety rules and take precautionary actions.

Safe practices have developed from past experience in the use of welding and cutting. These practices must be learned

through study and training before using this equipment. Some of these practices apply to equipment connected to

power lines; other practices apply to engine driven equipment. Anyone not having extensive training in welding and

cutting practices should not attempt to weld.

Safe practices are outlined in the Australian Standard AS1674.2-2007 entitled: Safety in welding and allied processes

Part 2: Electrical. This publication and other guides to what you should learn before operating this equipment are

listed at the end of these safety precautions. HAVE ALL INSTALLATION, OPERATION, MAINTENANCE, AND REPAIR

WORK PERFORMED ONLY BY QUALIFIED PEOPLE.

TRANSMIG 2RT

GENERAL INFORMATION 1-2 Manual 0-5196

WARNING

ARC RAYS can burn eyes and skin; NOISE can

damage hearing.

Arc rays from the welding process produce

intense heat and strong ultraviolet rays that

can burn eyes and skin. Noise from some

processes can damage hearing.

1. Use a Welding Helmet or Welding Faceshield ﬁ tted

with a proper shade of ﬁ lter (see ANSI Z49.1 and AS

1674 listed in Safety Standards) to protect your face

and eyes when welding or watching.

2. Wear approved safety glasses. Side shields recom-

mended.

3. Use protective screens or barriers to protect others

from ﬂ ash and glare; warn others not to watch the arc.

4. Wear protective clothing made from durable, ﬂ ame-

resistant material (wool and leather) and foot protec-

tion.

5. Use approved ear plugs or ear muffs if noise level is

high.

6. Never wear contact lenses while welding.

Recommended Protective Filters for Electric Welding

Description of Process

Approximate Range of

Welding Current in Amps

Minimum Shade Number of

Filter(s)

Manual Metal Arc Welding - covered

electrodes (MMAW)

Less than or equal to 100 8

100 to 200 10

200 to 300 11

300 to 400 12

Greater than 400 13

Gas Metal Arc Welding (GMAW)

(MIG) other than Aluminium and

Stainless Steel

Less than or equal to 150 10

150 to 250 11

250 to 300 12

300 to 400 13

Greater than 400 14

Gas Metal Arc Welding (GMAW)

(MIG) Aluminium and Stainless Steel

Less than or equal to 250 12

250 to 350 13

Gas Tungsten Arc Welding (GTAW)

(TIG)

Less than or equal to 100 10

100 to 200 11

200 to 250 12

250 to 350 13

Greater than 350 14

Flux-cored Arc Welding (FCAW) -with

or without shielding gas.

Less than or equal to 300 11

300 to 400 12

400 to 500 13

Greater than 500 14

Air - Arc Gouging Less than or equal to 400 12

Plasma - Arc Cutting

50 to 100 10

100 to 400 12

400 to 800 14

Plasma - Arc Spraying

—

Plasma - Arc Welding

Less than or equal to 20 8

20 to 100 10

100 to 400 12

400 to 800 14

Submerged - Arc Welding

—

2(5)

Resistance Welding

—

Safety Spectacles or eye shield

Refer to standard AS/NZS 1338.1:1992 for comprehensive information regarding the above table.

TRANSMIG 2RT

Manual 0-5196 1-3 GENERAL INFORMATION

WARNING

FUMES AND GASES can be hazardous to your

health.

Welding produces fumes and gases. Breathing

these fumes and gases can be hazardous to

your health.

1. Keep your head out of the fumes. Do not breath the

fumes.

2. If inside, ventilate the area and/or use exhaust at the

arc to remove welding fumes and gases.

3. If ventilation is poor, use an approved air-supplied

respirator.

4. Read the Material Safety Data Sheets (MSDSs) and the

manufacturer’s instruction for metals, consumables,

coatings, and cleaners.

5. Work in a conﬁ ned space only if it is well ventilated,

or while wearing an air-supplied respirator. Shielding

gases used for welding can displace air causing injury

or death. Be sure the breathing air is safe.

6. Do not weld in locations near degreasing, cleaning, or

spraying operations. The heat and rays of the arc can

react with vapours to form highly toxic and irritating

gases.

7. Do not weld on coated metals, such as galvanized,

lead, or cadmium plated steel, unless the coating is

removed from the weld area, the area is well ventilated,

and if necessary, while wearing an air-supplied respi-

rator. The coatings and any metals containing these

elements can give off toxic fumes if welded.

WARNING

WELDING can cause ﬁ re or explosion.

Sparks and spatter ﬂ y off from the welding arc.

The ﬂ ying sparks and hot metal, weld spatter,

hot workpiece, and hot equipment can cause

ﬁ res and burns. Accidental contact of electrode

or welding wire to metal objects can cause

sparks, overheating, or ﬁ re.

1. Protect yourself and others from ﬂ ying sparks and hot

metal.

2. Do not weld where ﬂ ying sparks can strike ﬂ ammable

material.

3. Remove all ﬂ ammables within 10M of the welding arc.

If this is not possible, tightly cover them with approved

covers.

4. Be alert that welding sparks and hot materials from

welding can easily go through small cracks and open-

ings to adjacent areas.

5. Watch for ﬁ re, and keep a ﬁ re extinguisher nearby.

6. Be aware that welding on a ceiling, ﬂ oor, bulkhead, or

partition can cause ﬁ re on the hidden side.

7. Do not weld on closed containers such as tanks or

drums.

8. Connect work cable to the work as close to the weld-

ing area as practical to prevent welding current from

travelling long, possibly unknown paths and causing

electric shock and ﬁ re hazards.

9. Do not use welder to thaw frozen pipes.

10. Remove stick electrode from holder or cut off welding

wire at contact tip when not in use.

WARNING

FLYING SPARKS AND HOT METAL can cause

injury.

Chipping and grinding cause ﬂ ying metal. As

welds cool, they can throw off slag.

1. Wear approved face shield or safety goggles. Side

shields recommended.

2. Wear proper body protection to protect skin.

WARNING

CYLINDERS can explode if damaged.

Shielding gas cylinders contain gas under

high pressure. If damaged, a cylinder can

explode. Since gas cylinders are normally

part of the welding process, be sure to treat

them carefully.

1. Protect compressed gas cylinders from excessive

heat, mechanical shocks, and arcs.

2. Install and secure cylinders in an upright position by

chaining them to a stationary support or equipment

cylinder rack to prevent falling or tipping.

TRANSMIG 2RT

GENERAL INFORMATION 1-4 Manual 0-5196

3. Keep cylinders away from any welding or other electri-

cal circuits.

4. Never allow a welding electrode to touch any cylinder.

5. Use only correct shielding gas cylinders, regulators,

hoses, and ﬁ ttings designed for the speciﬁ c application;

maintain them and associated parts in good condition.

6. Turn face away from valve outlet when opening

cylinder valve.

7. Keep protective cap in place over valve except when

cylinder is in use or connected for use.

8. Read and follow instructions on compressed gas

cylinders, associated equipment, and CGA publication

P-1 listed in Safety Standards.

WARNING

MOVING PARTS can cause injury.

Moving parts, such as fans, rotors, and belts can cut

ﬁ ngers and hands and catch loose clothing.

1. Keep all doors, panels, covers, and guards closed and

securely in place.

2. Stop engine before installing or connecting unit.

3. Have only qualiﬁ ed people remove guards or covers

for maintenance and troubleshooting as necessary.

4. To prevent accidental starting during servicing, discon-

nect negative (-) battery cable from battery.

5. Keep hands, hair, loose clothing, and tools away from

moving parts.

6. Reinstall panels or guards and close doors when

servicing is ﬁ nished and before starting engine.

WARNING

This product, when used for welding or cut-

ting, produces fumes or gases which contain

chemicals know to the State of California to

cause birth defects and, in some cases, cancer.

(California Health & Safety code Sec. 25249.5

et seq.)

NOTE

Considerations About Welding And The Effects

of Low Frequency Electric and Magnetic Fields

The following is a quotation from the General Con-

clusions Section of the U.S. Congress, Office of

Technology Assessment, Biological Effects of Power

Frequency Electric & Magnetic Fields - Background Paper,

OTA-BP-E-63 (Washington, DC: U.S. Government Printing

Ofﬁ ce, May 1989): “...there is now a very large volume

of scientiﬁ c ﬁ ndings based on experiments at the cellular

level and from studies with animals and people which

clearly establish that low frequency magnetic ﬁ elds and

interact with, and produce changes in, biological systems.

While most of this work is of very high quality, the results

are complex. Current scientiﬁ c understanding does not

yet allow us to interpret the evidence in a single coherent

framework. Even more frustrating, it does not yet allow us

to draw deﬁ nite conclusions about questions of possible

risk or to offer clear science-based advice on strategies

to minimize or avoid potential risks.”

To reduce magnetic ﬁ elds in the workplace, use the fol-

lowing procedures.

1. Keep cables close together by twisting or taping them.

2. Arrange cables to one side and away from the operator.

3. Do not coil or drape cable around the body.

4. Keep welding power source and cables as far away

from body as practical.

ABOUT PACEMAKERS:

The above procedures are among those

also normally recommended for pacemaker

wearers. Consult your doctor for complete

information.

TRANSMIG 2RT

Manual 0-5196 1-5 GENERAL INFORMATION

1.02 Principal Safety Standards

Safety in Welding and Cutting, ANSI Standard Z49.1, from American Welding Society, 550 N.W. LeJeune Rd., Miami,

FL 33126.

Safety and Health Standards, OSHA 29 CFR 1910, from Superintendent of Documents, U.S. Government Printing

Ofﬁ ce, Washington, D.C. 20402.

Recommended Safe Practices for the Preparation for Welding and Cutting of Containers That Have Held Hazardous

Substances, American Welding Society Standard AWS F4.1, from American Welding Society, 550 N.W. LeJeune Rd.,

Miami, FL 33126.

National Electrical Code, NFPA Standard 70, from National Fire Protection Association, Batterymarch Park, Quincy,

MA 02269.

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1, from Compressed Gas Association, 1235 Jef-

ferson Davis Highway, Suite 501, Arlington, VA 22202.

Code for Safety in Welding and Cutting, CSA Standard W117.2, from Canadian Standards Association, Standards

Sales, 178 Rexdale Boulevard, Rexdale, Ontario, Canada M9W 1R3.

Safe Practices for Occupation and Educational Eye and Face Protection, ANSI Standard Z87.1, from American National

Standards Institute, 1430 Broadway, New York, NY 10018.

Cutting and Welding Processes, NFPA Standard 51B, from National Fire Protection Association, Batterymarch Park,

Quincy, MA 02269.

Safety in welding and allied processes Part 1: Fire Precautions, AS 1674.1-1997 from SAI Global Limited, www.

saiglobal.com.

Safety in welding and allied processes Part 2: Electrical, AS 1674.2-2007 from SAI Global Limited, www.saiglobal.com.

Filters for eye protectors - Filters for protection against radiation generated in welding and allied operations AS/NZS

1338.1:1992 from SAI Global Limited, www.saiglobal.com.

TRANSMIG 2RT

GENERAL INFORMATION 1-6 Manual 0-5196

1.03 Declaration of Conformity

Manufacturer: CIGWELD

Address: 71 Gower St, Preston

Victoria 3072

Australia

Description of equipment: Welding Equipment (GMAW, FCAW, ) including, but not limited to CIGWELD Transmig 2RT

wire feeder and associated accessories.

Serial numbers are unique with each individual piece of equipment and details description, parts used to manufacture

a unit and date of manufacture.

The equipment conforms to all applicable aspects and regulations of the ‘Low Voltage Directive’ (Directive 73/23/EU,

as recently changed in Directive 93/68/EU and to the National legislation for the enforcement of the Directive.

National Standard and Technical Speciﬁ cations

The product is designed and manufactured to a number of standards and technical requirements among them are:

• IEC 60974-10 applicable to Industrial Equipment - generic emissions and regulations.

• AS 1674 Safety in welding and allied processes.

• IEC 60974-5 Arc welding equipment, Wirefeeders.

Extensive product design veriﬁ cation is conducted at the manufacturing facility as part of the routine design and

manufacturing process, to ensure the product is safe and performs as speciﬁ ed. Rigorous testing is incorporated into

the manufacturing process to ensure the manufactured product meets or exceeds all design speciﬁ cations.

CIGWELD has been manufacturing and merchandising an extensive equipment range with superior performance, ultra

safe operation and world class quality for more than 30 years and will continue to achieve excellence.

INTRODUCTION TRANSMIG 2RT

Manual 0-5196 2-1 INTRODUCTION

SECTION 2: INTRODUCTION

2.02 Equipment Identiﬁ cation

The unit’s identiﬁ cation number (speciﬁ cation or part

number), model, and serial number usually appear on

a nameplate attached to the machine. Equipment which

does not have a nameplate attached to the machine is

identiﬁ ed only by the speciﬁ cation or part number printed

on the shipping container. Record these numbers for

future reference.

2.03 Receipt of Equipment

When you receive the equipment, check it against the

invoice to make sure it is complete and inspect the equip-

ment for possible damage due to shipping. If there is any

damage, notify the carrier immediately to ﬁ le a claim.

Furnish complete information concerning damage claims

or shipping errors to the location in your area listed in the

inside back cover of this manual.

Include all equipment identiﬁ cation numbers as described

above along with a full description of the parts in error.

Move the equipment to the installation site before un-

crating the unit. Use care to avoid damaging the equip-

ment when using bars, hammers, etc., to un-crate the unit.

2.01 How to Use This Manual

This Operating Manual usually applies to the part numbers

listed on page i. To ensure safe operation, read the entire

manual, including the chapter on safety instructions and

warnings. Throughout this manual, the word WARNING,

CAUTION and NOTE may appear. Pay particular attention

to the information provided under these headings. These

special annotations are easily recognized as follows:

WARNING

Gives information regarding possible personal

injury. Warnings will be enclosed in a box

such as this.

CAUTION

Refers to possible equipment damage. Cau-

tions will be shown in bold type.

NOTE

Offers helpful information concerning certain

operating procedures. Notes will be shown

in italics

Additional copies of this manual may be purchased by

contacting Cigweld at the address and phone number

for your location listed in the inside back cover of this

manual. Include the Owner’s Manual number and equip-

ment identiﬁ cation numbers.

TRANSMIG 2RT INTRODUCTION

INTRODUCTION 2-2 Manual 0-5196

2.04 Symbol Chart

Note that only some of these symbols will appear on your model.

Gas Tungsten Arc

Welding (GTAW)

Air Carbon Arc

Cutting (CAC-A)

Constant Current

Constant Voltage

Or Constant Potential

High Temperature

Fault Indication

Arc Force

Touch Start (GTAW)

Variable Inductance

Voltage Input

Single Phase

Three Phase

Three Phase Static

Frequency Converter-

Transformer-Rectifier

Dangerous Voltage

Off

Panel/Local

Manual Metal

Arc Welding (MMAW)

Gas Metal Arc

Welding (GMAW)

Increase/Decrease

Circuit Breaker

AC Auxiliary Power

Remote

Duty Cycle

Percentage

Amperage

Voltage

Hertz (cycles/sec)

Frequency

Negative

Positive

Direct Current (DC)

Protective Earth

(Ground)

Line

Line Connection

Auxiliary Power

Receptacle Rating-

Auxiliary Power

Art # A-10344

115V 15A

IPM

MPM

Fuse

Wire Feed Function

Wire Feed Towards

Workpiece With

Output Voltage Off.

Preflow Time

Postflow Time

Spot Time

Spot Weld Mode

Continuous Weld

Mode

Press to initiate wirefeed and

welding, release to stop.

Purging Of Gas

Inches Per Minute

Meters Per Minute

Disturbance In

Ground System

Welding Torch

Burnback Time

Press and hold for preflow, release

to start arc. Press to stop arc, and

hold for preflow.

4 Step Trigger

Operation

2 Step Trigger

Operation

Figure 2-1 Symbol chart

INTRODUCTION TRANSMIG 2RT

Manual 0-5196 2-3 INTRODUCTION

2.05 Description

The Transmig 2RT Wirefeeder is fully compliant to Stand-

ard IEC 60974.5.The Transmig 2RT Wirefeeder when used

in conjunction with the Transmig 250i Multi Process Weld-

er provides excellent MIG welding performance across a

broad range of applications when used with the correct

welding consumables and procedures. The instructions

in the next section detail how to correctly and safely set

up the machine and give guidelines on gaining the best

efﬁ ciency and quality from the Power Source. Please read

these instructions thoroughly before using the unit.

2.06 User Responsibility

This equipment will perform as per the information con-

tained herein when installed, operated, maintained and

repaired in accordance with the instructions provided.

This equipment must be checked periodically. Defective

equipment (including welding leads) should not be used.

Parts that are broken, missing, plainly worn, distorted or

contaminated, should be replaced immediately. Should

such repairs or replacements become necessary, it is

recommended that such repairs be carried out by appro-

priately qualiﬁ ed persons approved by CIGWELD. Advice

in this regard can be obtained by contacting an Accredited

CIGWELD Distributor.

This equipment or any of its parts should not be altered

from standard speciﬁ cation without prior written approval

of CIGWELD. The user of this equipment shall have the

sole responsibility for any malfunction which results from

improper use or unauthorized modiﬁ cation from standard

speciﬁ cation, faulty maintenance, damage or improper re-

pair by anyone other than appropriately qualiﬁ ed persons

approved by CIGWELD.

2.07 Transportation Methods

WARNING

ELECTRIC SHOCK can kill. DO NOT TOUCH

live electrical parts. Disconnect input power

conductors from de-energized supply line

before moving the welding power source.

WARNING

FALLING EQUIPMENT can cause serious per-

sonal injury and equipment damage.

Lift unit with integrated handle at the top of the unit.

Use handcart or similar device of adequate capacity.

If using a fork lift vehicle, place and secure unit on a proper

skid before transporting.

2.08 Packaged Items

Transmig 2RT Wirefeeder

(Part No. W3000500)

• Transmig 2RT Wirefeeder

• 8M Interconnection Lead, Fitted

• Operating Manual

• Drive Roll 0.9-1.2mm, Fitted

• Pressure Roll 0.6-1.2mm Solid Wire, Fitted

• Outlet Guide 0.9-1.2mm, Fitted

TRANSMIG 2RT INTRODUCTION

INTRODUCTION 2-4 Manual 0-5196

2.09 Speciﬁ cations

Description Transmig 2RT Wirefeeder

Wirefeeder Plant Part Number W3000500

Wirefeeder Plant Dimensions H 453mm x W 238mm x D 553mm

Wirefeeder Plant Mass 25kg

Wire Feed Motor Voltage 24 VDC

Gas Solenoid Voltage 24 VDC

MIG (GMAW) Welding Output,

40°C, 10 min

30% @ 350A

60% @ 250A

100% @ 205A

Minimum Wire Speed 1.2 MPM

Maximum Wire Speed 17.8 MPM

Operating Temperature Range 0°C - 40°C

Interconnection Plug 10 Pin

Interconnection Length 8 metre

Table 2-1: Transmig 2RT Speciﬁ cation

NOTE

Due to variations that can occur in manufactured products, claimed performance, voltages, ratings, all

capacities, measurements, dimensions and weights quoted are approximate only. Achievable capacities and

ratings in use and operation will depend upon correct installation, use, applications, maintenance and service.

INSTALLATION/SETUP TRANSMIG 2RT

Manual 0-5196 3-1 INSTALLATION/SETUP

3.01 Environment

These units are designed for use in environments with

increased hazard of electric shock as outlined in IEC

60974.5.

A. Examples of environments with increased hazard of

electric shock are:

1. In locations in which freedom of movement is re-

stricted, so that the operator is forced to perform the

work in a cramped (kneeling, sitting or lying) position

with physical contact with conductive parts.

2. In locations which are fully or partially limited by con-

ductive elements, and in which there is a high risk of

unavoidable or accidental contact by the operator.

3. In wet or damp hot locations where humidity or per-

spiration considerably reduces the skin resistance

of the human body and the insulation properties of

accessories.

B. Environments with increased hazard of electric shock

do not include places where electrically conductive parts in

the near vicinity of the operator, which can cause increased

hazard, have been insulated.

3.02 Location

Be sure to locate the welder according to the following

guidelines:

A. In areas, free from moisture and dust.

B. Ambient temperature between 0° C to 40° C.

C. In areas, free from oil, steam and corrosive gases.

D. In areas, not subjected to abnormal vibration or shock.

E. In areas, not exposed to direct sunlight or rain.

F. The enclosure design of this Wire Feeder meets the

requirements of IP23S as outlined in AS60529. This

provides adequate protection against solid objects

(greater than 12mm), and direct protection from verti-

cal drops. Under no circumstances should the unit be

operated or connected in a micro environment that will

exceed the stated conditions. For further information

please refer to AS 60529.

G. Precautions must be taken against the Wire Feeder

toppling over. The Wire Feeder must be located on

a suitable horizontal surface in the upright position

when in use.

SECTION 3: INSTALLATION OPERATION AND SETUP

WARNING

This equipment should be electrically

connected by a qualiﬁ ed electrician.

3.03 Ventilation

WARNING

Since the inhalation of welding fumes can

be harmful, ensure that the welding area is

effectively ventilated.

3.04 Mains Supply Voltage

Requirements

See Operating Manual for Transmig 250i.

3.05 Electromagnetic Compatibility

WARNING

Extra precautions for Electromagnetic

Compatibility may be required when this

Welding Power Source is used in a domestic

situation.

A. Installation and Use - Users Responsibility

The user is responsible for installing and using the welding

equipment according to the manufacturer’s instructions.

If electromagnetic disturbances are detected then it shall

be the responsibility of the user of the welding equipment

to resolve the situation with the technical assistance of

the manufacturer. In some cases this remedial action

may be as simple as earthing the welding circuit, see

NOTE below. In other cases it could involve constructing

an electromagnetic screen enclosing the Welding Power

Source and the work, complete with associated input

ﬁ lters. In all cases, electromagnetic disturbances shall be

reduced to the point where they are no longer Trouble-

some.

TRANSMIG 2RT INSTALLATION/SETUP

INSTALLATION/SETUP 3-2 Manual 0-5196

NOTE

The welding circuit may or may nor be earthed

for safety reasons. Changing the earthing ar-

rangements should only be authorised by a

person who is competent to assess whether

the changes will increase the risk of injury,

e.g. by allowing parallel welding current return

paths which may damage the earth circuits of

other equipment. Further guidance is given in

IEC 60974-13 Arc Welding Equipment - Instal-

lation and use (under preparation).

B. Assessment of Area

Before installing welding equipment, the user shall make

an assessment of potential electromagnetic problems in

the surrounding area. The following shall be taken into

account.

1. Other supply cables, control cables, signalling and

telephone cables; above, below and adjacent to the

welding equipment.

2. Radio and television transmitters and receivers.

3. Computer and other control equipment.

4. Safety critical equipment, e.g. guarding of industrial

equipment.

5. The health of people around, e.g. the use of pace-

makers and hearing aids.

6. Equipment used for calibration and measurement.

7. The time of day that welding or other activities are to

be carried out.

8. The immunity of other equipment in the environment:

the user shall ensure that other equipment being used

in the environment is compatible: this may require

additional protection measures.

The size of the surrounding area to be considered will

depend on the structure of the building and other activities

that are taking place. The surrounding area may extend

beyond the boundaries of the premises.

C. Methods of Reducing Electromagnetic Emissions

1. Mains Supply

Welding equipment should be connected to the

mains supply according to the manufacturer’s

recommendations. If interference occurs, it may be

necessary to take additional precautions such as

ﬁ ltering of the mains supply. Consideration should

be given to shielding the supply cable of permanently

installed welding equipment in metallic conduit or

equivalent. Shielding should be electrically continuous

throughout its length. The shielding should be

connected to the Welding Power Source so that good

electrical contact is maintained between the conduit

and the Welding Power Source enclosure.

2. Maintenance of Welding Equipment

The welding equipment should be routinely maintained

according to the manufacturer’s recommendations. All

access and service doors and covers should be closed

and properly fastened when the welding equipment

is in operation. The welding equipment should not

be modiﬁ ed in any way except for those changes

and adjustments covered in the manufacturer’s

instructions.

3. Welding Cables

The welding cables should be kept as short as possible

and should be positioned close together but never

coiled and running at or close to the ﬂ oor level.

4. Equipotential Bonding

Bonding of all metallic components in the welding

installation and adjacent to it should be considered.

However, metallic components bonded to the work

piece will increase the risk that the operator could

receive a shock by touching the metallic components

and the electrode at the same time. The operator

should be insulated from all such bonded metallic

components.

5. Earthing/grounding of the Work Piece

Where the work piece is not bonded to earth for electri-

cal safety, nor connected to earth because of its size

and position, e.g. ship’s hull or building steelwork,

a connection bonding the work piece to earth may

reduce emissions in some, but not all instances. Care

should be taken to prevent the earthing of the work

piece increasing the risk of injury to users, or damage

to other electrical equipment. Where necessary, the

connection of the work piece to earth should be made

by direct connection to the work piece, but in some

countries where direct connection is not permitted, the

bonding should be achieved by suitable capacitance,

selected according to national regulations.

6. Screening and Shielding

Selective screening and shielding of other cables

and equipment in the surrounding area may alleviate

problems of interference. Screening the entire welding

installation may be considered for special applications.

INSTALLATION/SETUP TRANSMIG 2RT

Manual 0-5196 3-3 INSTALLATION/SETUP

3.06 2RT Wire Feeder Controls,

Indicators and Features

The 2RT Wirefeeder is designed to be used with the

Transmig 250i. Select MIG Process and REMT in the

Advanced Features menu on the Transmig 250i to enable

the controls on the 2RT wirefeeder. See the 250i Operat-

ing manual for details.

Vol ts

Wirespeed

Left Knob

Right Knob

Art # A-10404

Figure 3-1: 2RT Front Panel Controls

Art # A-10470_AB

REMOTE

LOCAL

Figure 3-2: 2RT Local/Remote Switch

The Tweco professional MIG Torch will connect to the 2RT

just as it does to the 250i power source. The electrode

Polarity setting is done at the power source. See sub

sections 3.09 and 3.10.

1. Left Knob: WFS (Wire Feed Speed) Control

Amperage Control

Wirespeed

Left Knob

The Left Knob controls the Wirespeed in the wirefeeder.

It adjusts the preview wire speed display in the power

source. The amperage control knob adjusts the amount

of welding current delivered by the power source. In MIG

mode, the amperage knob adjusts the speed of the wire

feed motor (which in turn adjusts the output current by

varying the amount of MIG wire delivered to the welding

arc). The optimum wire speed required is dependent on

the type of welding application. The setup chart on the

inside of the wire feed compartment door of the Transmig

250i provides a brief summary of the required output set-

tings for a basic range of MIG welding applications. The

value may also be adjusted while a weld is in progress – if

this occurs, the left display will brieﬂ y switch to show the

adjusted value as the knob on the 2RT is turned, and will

automatically revert back to showing the set weld current

measurements when the knob is not being turned.

2. Right Knob: MIG Voltage Control

Right Knob

MIG Voltage Control

In this mode the control knob is used to adjust the output

voltage of the power source. It adjusts the preview volt-

age display in the power source. The welding voltage is

increased by turning the knob on the 2RT clockwise or

decreased by turning the knob anti-clockwise. The opti-

mum voltage level required is dependent on the type of

welding application. The setup chart on the inside of the

wire feed compartment door of the power supply provides

a brief summary of the required output settings for a basic

range of MIG welding applications. The value may also

be adjusted while a weld is in progress – if this occurs,

the left display on the power supply will brieﬂ y switch to

show the adjusted value as the knob on the 2RT is turned,

and will automatically revert back to showing the set weld

current measurements when the knob is not being turned.

TRANSMIG 2RT INSTALLATION/SETUP

INSTALLATION/SETUP 3-4 Manual 0-5196

3. MIG Torch Adaptor (Euro Style)

The MIG Torch adaptor is the connection point for the MIG welding Torch. Connect the MIG Torch by pushing the

MIG Torch connector into the brass MIG Torch adaptor ﬁ rmly and screwing the plastic MIG Torch nut clockwise

to secure in position. To remove the MIG Torch simply reverse these directions.

4. Remote Control Socket

The 8 pin Remote Control Socket is used to connect remote control devices to the 2RT Wirefeeder. To make con-

nections, align keyway, insert plug, and rotate threaded collar fully clockwise.

Trigger Switch

Remote Wirespeed in GMAW mode

Remote Volts in

GMAW Mode

A-10477

Figure 3-3: Remote Control Socket

Socket Pin

Function

1 Not connected

Trigger Switch Input

Not connected

5k ohm (maximum) connection to 5k ohm remote control potentiometer.

Zero ohm (minimum) connection to 5k ohm remote control potentiometer.

Wiper arm connection to 5k ohm remote control Wirespeed MIG mode potentiometer.

Wiper arm connection to 5k ohm remote control Volts MIG mode potentiometer.

Table 3-1

5. Local/Remote Switch (Located in wire feed compartment)

The remote / local switch(inside the 2RT) is used to switch between using the controls on the wire feeder and

using controls on a remote device attached to the wirefeeder (such as a MIG Gun with remote voltage and wire

feed speed control). To use the controls on the wirefeeder the switch must be in the Local position. When the lo-

cal/remote switch is in the local position, the 2 RT wirefeeder controls will take over and all voltage and wire feed

speed will be made from there. To use a remote control device (such as a MIG Gun with remote voltage and wire

feed speed control) the switch must be in the Remote position. Note that the MIG Gun trigger will operate at all

times regardless of the position of the local remote switch (i.e. in both local and remote modes).

Page is loading ...

ESAB 2RT Transmig Wire Feeder User manual

Brand: ESAB

Model: 2RT Transmig Wire Feeder

Category: Welding System

Type: User manual

Download PDF

report

ESAB 2RT Transmig Wire Feeder User manual

ESAB 2RT Transmig Wire Feeder User manual

Related papers

Other documents