Elkay LKUMSK36 Installation guide

Type
Installation guide

Elkay LKUMSK36 is an undermount support kit designed for installing sinks in cabinets. It includes rails, mounting brackets, adjusting bolts, nuts, plastic bolt caps, wood screws, and joiner clips. The kit allows for precise positioning and leveling of the sink, ensuring a flush fit with the countertop. It is suitable for various sink shapes and sizes, except for those with left or right dimensions of 36 inches or greater. The kit provides a sturdy and secure support system for undermount sinks, making it a valuable tool for kitchen and bathroom remodeling projects.

Elkay LKUMSK36 is an undermount support kit designed for installing sinks in cabinets. It includes rails, mounting brackets, adjusting bolts, nuts, plastic bolt caps, wood screws, and joiner clips. The kit allows for precise positioning and leveling of the sink, ensuring a flush fit with the countertop. It is suitable for various sink shapes and sizes, except for those with left or right dimensions of 36 inches or greater. The kit provides a sturdy and secure support system for undermount sinks, making it a valuable tool for kitchen and bathroom remodeling projects.

Installation Instructions
Undermount Support Kit
Illustration 1A
Illustration 2
Illustration 3
Illustration 2A
Elkay
2222 Camden Court
Oak Brook, IL 60523
©2009 Elkay
Printed in the U.S.A.
elkayusa.com
(4/09) PART NO. 74180611
4. Determine exact location where rail is to be installed in
cabinet. Make sure rail adjustment bolts come into contact
with the underside of the sink ledge. Determine exact loca-
tion where mounting bracket will be installed. Mark on
cabinet frame where holes in bracket are located. Drill
starter holes where marked using a 3/32” drill bit.
*Note: Depending upon fabrication of countertop, top of
mounting bracket may need to be no
tched into top of
cabinet frame.
5. Screw mounting bracket to sides of cabinet frame.
6. Lower rail into mounting bracket.
7. Slip bolt caps onto end of bolts.
8. Carefully lower the sink onto the bolt caps.
9. Carefully adjust bolts to raise and level the sink flush with
the underside of the countertop.
*Note: Caulk should be used where sink comes into con-
tact with underside of the countertop.
10. This kit is
not recommended on sinks with a left or right
dimension of 36" (914mm) or greater, or sinks with shapes
that do not allow the kit to have sufficient contact.
11. If a rear left to right rail will interfere with faucet installa-
tions, use only a left to right rail in front.
1. Identify parts. This pack includes:
a) 25" (635mm) or 36" (914mm) rails (2 each)
b) Mounting brackets (4 each)
c) 2" (51mm) adjusting bolts (8 e
ach)
d) Nuts (8 each)
e) Plastic bolt caps (8 each)
f) Wood screws (16 each)
g) Joiner clips (2 each)
(See Illustration 1A) Discard if not using.
2. If needed, cut (with hacksaw) the rails 1/8" (3mm) less than
the distance of the inside of the cabinet (front to back
only). For sinks that are: round or oval; 25" (635mm) or
greater left to right; or double bowl sinks, a second set of
rails will be needed. Cut the
second set of rails the neces-
sary distance between the first set.
3. Screw adjust bolts into nuts 2 turns and then slide nuts
onto rail. Slide into position in desired openings of rail
(See Illustration 2). For e-Granite or fine fireclay sink
models assemble as shown in Illustration 2A.
Sink
Rail
Mounting Bracket
Cabinet
Frame
Notch
cabinet
frame if
needed
Countertop
Silicone
Caulk
Rear of
Cabinet
1st Set of Rails
Front of
Cabinet
4 Joiner
Clips in
Channels
(Item g)
Side View
4 Bolts
2nd Set of Rails
Illustration 1
Front of
Cabinet
Rear of
Cabinet
Cabinet
Frame
Cabinet
Frame
a
e
b
  • Page 1 1

Elkay LKUMSK36 Installation guide

Type
Installation guide

Elkay LKUMSK36 is an undermount support kit designed for installing sinks in cabinets. It includes rails, mounting brackets, adjusting bolts, nuts, plastic bolt caps, wood screws, and joiner clips. The kit allows for precise positioning and leveling of the sink, ensuring a flush fit with the countertop. It is suitable for various sink shapes and sizes, except for those with left or right dimensions of 36 inches or greater. The kit provides a sturdy and secure support system for undermount sinks, making it a valuable tool for kitchen and bathroom remodeling projects.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI