ROBLIN ACTIS PRO 77 Owner's manual

NOTICE D’INSTALLATION ET D’UTILISATION

INSTRUCTIONS FOR INSTALLATION AND DIRECTIONS FOR USE

MONTAGE- UND

GEBRAUCHSANWEIS

UNG

LIBRETTO DI ISTRUZIONI

INST

RUCCIONES DE INSTALACION E UTILIZACION

MONTAGE- EN

GEBRUIKSHANDLEIDING

ACTIS Pro 57/77

F SOMMAIRE

RACCORDEMENT ÉLECTRIQUE

CONSEILS D’INSTALLATIONS

POSE DE L’APPAREIL

FONCTIONNEMENT

CONSEILS D’UTILISATIONS

ENTRETIEN

GARANTIE ET SERVICE APRÈS-VENTE

REMARQUES

D INHALT

NETZANSCHLUSS

MONTAGEHILFEN

MONTAGE DES GERÄTES

BETRIEB DES GERÄTES

NUTZUNG

WARTUNG UND REINIGUNG

GARANTIE UND KUNDENDIENST

WICHTIGE HINVEISE

E SUMARIO

CONEXION ELECTRICA

CONSEJOS DE INSTALACION

INSTALACION DEL APARATO

FUNCIONAMIENTO

CONSEJOS DE UTILIZACION

MANTENIMIENTO

GARANTIA Y ASSISTENCIA TECNICA

NOTA

GB CONTENTS

ELECTRICAL WIRING

INSTALLATION ADVICE

FITTING THE APPLIANCE

OPERATION

USEFUL HINTS

MAINTENANCE

GUARANTEE AND AFTER-SALES-SERVICES

REMARKS

I CONTENUTI

COLLEGAMENTO ELETTRICO

CONSIGLI DI INSTALLAZIONE

POSA DELL’ APPARECCHIO

FUNZIONAMENTO

CONSICLI DI UTILIZZO

MANUTENZIONE

GARANZIA ED ASSISTENZA TECNICA

NOTE

NL INHOUD

ELECTRISCHE BEDRADING

MONTAGE AANWIJZING

AANSLUITEN VAN HET APPARAAT

FUNKTIONEREN

GEBRUIKSADVIES

ONDERHOUD

AFTER SALES SERVICE

OPMERKINGEN

Page is loading ...

4

GB

Thank you for buying a ROBLIN product which has been manufactured to the highest quality standards

to meet your requirements.

We recommend you carefully read this booklet in which you will ﬁnd instructions for installation, hints for

use and maintenance.

The Instructions for Use apply to several versions of this appliance. Accordingly, you may ﬁnd descrip-

tions of individual features that do not apply to your speciﬁc appliance.

1 ELECTRICAL

• This cooker hood is ﬁtted with a 3-core mains cable with a standard 10/16A earthed plug.

•

Alternatively the hood can be connected to the mains supply via a double-pole switch having 3mm

minimum contact gap on each pole.

• Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on

the rating plate inside the cooker hood.

• Technical Speciﬁcation: Voltage 220-240 V, single phase ~ 50 Hz / 220 V - 60Hz.

2 INSTALLATION ADVICE

• Ensure the cooker hood is ﬁtted in compliance with the recommended ﬁxing heights.

•

To ensure the safe operation of this cooker hood, we recommend that the hood should not be ﬁtted

below 65cm (for electric) or (70cm for gas) the measurements taken from the surface of the cooking

appliance to the underside of the cooker hood.

•

It is a possible ﬁre risk if the hood is not sited as recommended.

• To ensure the best results, the cooking fumes should be able to rise naturally towards the inlet grilles

on the underside of the cooker hood and the cooker hood should be positioned away from doors and

windows, which will create turbulence.

•

Ducting

• If the room where the hood is to be used contains a fuel-burning appliance such as a central heating

boiler then its ﬂue must be of the room sealed or balanced ﬂue type.

• If other types of ﬂue or appliances are ﬁtted ensure that there is an adequate supply of fresh air to

the room. Ensure the kitchen is ﬁtted with an airbrick, which should have a cross-sectional measurement

equivalent to the diameter of the ducting being ﬁtted, if not larger.

• The ducting system for this cooker hood must not be connected to any existing ventilation system,

which is being used for any other purposes or to a mechanically controlled ventilation ducting.

•

The ducting used must be made from ﬁre retardant materials and the correct diameter must be used,

as incorrect sized ducting will affect the performance of this cooker hood.

• When the cooker hood is used in conjunction with other appliances supplied with energy other than

electricity, the negative pressure in the room must not exceed 0.04 mbar to prevent the fumes from

combustion being drawn back into the room.

•

The appliance is for domestic use only and should not be operated by children or people who are

inﬁrm without supervision.

• This appliance must be positioned so that the wall socket is accessible.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

3 FITTING

Any permanent electrical installation must comply with the latest regulations concerning this type of instal-

lation

and a qualiﬁed electrician must carry out the work. Non-compliance could cause serious accidents

or injury and would deem the manufacturers guarantee null and void.

IMPORTANT - The wires in this mains lead are coloured in accordance with the following code :

5

GB

green / yellow : earth blue : neutral brown : live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured

markings identifying the terminals in your plug, proceed as follows.

-

The wire which is coloured green and yellow must be connected to the terminal in the plug which is

marked with the letter E or by the earth symbol

or coloured green or green and yellow.

- The wire which is coloured blue must be connected to the terminal which is marked with the letter N

or coloured black.

- The wire which is coloured brown must be connected to the terminal which is marked with the letter

L or coloured red.

ATTENTION: Do not forget to use adequate plugs to the support brackets. Enquire after the manu-

facturers. Do an embedding if necessary. The manufacturer accepts no responsibility in case of a

faulty hanging due to the drilling and the setting up of plugs.

The extractor unit is ﬁtted into the base board of the cooker hood (thickness: 12 to 22 mm). (Fig 1)

Connect the electrical plug and set the extractor tube in place.

Clip the appliance into the cutout; the 4 adjustable fastening clips are made ﬂexible to allow quick

assembly without the need for any complicated prior dismounting. Retighten the screws if necessary.

Ducting:

The hood is more effective when used in the extraction mode (ducted to the outside). When the cooker

hood is ducted to the outside, charcoal ﬁlters are not required.The ducting used must be 150 mm (6 INS),

rigid circular pipe and must be manufactured from ﬁre retardant material, produced to BS.476 or DIN

4102-B1. Wherever possible use rigid circular pipe which has a smooth interior, rather than the expanding

concertina type ducting.

Maximum length of ducting run:

- 4 metres with 1 x 90° bend.

- 3 metres with 2 x 90° bends.

- 2 metres with 3 x 90° bends.

The above assumes our 150 mm (6 INS) ducting is being installed.

Please note ducting components and ducting kits are optional accessories and have to be ordered,

they are not automatically supplied with the chimney hood.

•RECYCLING

The air is recirculated into the kitchen through the opening located on the upper side of the cabinet

or of the hood (Fig. 2).

Install the charcoal ﬁlters inside the canopy (Fig 3).

4 OPERATION

Key

. : Speed 1

Key

.. : Speed 2

Key

... : Speed 3

Key

: High Speed

Key

: Lighting

6

GB

5 USEFUL HINTS

• To obtain the best performance we recommend you to switch ‘ON’ the cooker hood a few minutes (in

the boost setting) before you start cooking and you should leave it running for approximately 15 minutes

after ﬁnishing.

• IMPORTANT: NEVER DO FLAMBÉ COOKING UNDER THIS COOKER HOOD

• Do not leave frying pans unattended during use as over-heated fat and oil might catch ﬁre.

• Do not leave naked ﬂames under this cooker hood.

• Switch ‘OFF’ the electric and gas before removing pots and pans.

• Ensure heating areas on your hotplate are covered with pots and pans when using the hotplate

and cooker hood simultaneously.

6 MAINTENANCE

Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply.

The cooker hood must be kept clean; a build up of fat or grease may cause a ﬁre hazard.

Casing

•

Wipe the cooker hood frequently with a clean cloth, which has been immersed in warm water contain-

ing a mild detergent and wrung out.

• Never use excessive amounts of water when cleaning particularly around the control panel.

• Never use scouring pads or abrasive cleaners.

• Always wear protective gloves when cleaning the cooker hood.

Metal Grease Filters : The metal grease ﬁlters absorb grease and dust during cooking in order to keep

clean the cooker hood inside. The grease ﬁlters should be cleaned once a month or more frequently if

the hood is used for more than 3 hours per day.

To remove and replace the metal grease ﬁlters

• Remove the metal grease ﬁlters one at a time by releasing the catches on the ﬁlters; the ﬁlters can

now be removed.

•

The metal grease ﬁlters should be washed, by hand, in mild soapy water or in a dishwasher.

• Allow to dry before replacing.

Active Charcoal Filter : The charcoal ﬁlter cannot be cleaned. The ﬁlter should be replaced at least

every three months or more frequently if the hood is used for more than three hours per day.

To remove and replace the ﬁlter

• Remove the metal grease ﬁlters.

• Press against the two retaining clips, which hold the charcoal ﬁlter in place and this will allow the ﬁlter

to drop down and be removed.

•

Clean the surrounding area and metal grease ﬁlters as directed above.

• Insert the replacement ﬁlter and ensure the two retaining clips are correctly located.

• Replace the metal grease ﬁlters.

Extraction tube : Check every 6 months that the dirty air is being extracted correctly. Comply with local

rules and regulations with regard to the extraction of ventilated air.

Lighting : If the lamp fails to function check to ensure it is ﬁtted correctly into the holder. If lamp failure

has occurred then it should be replaced with identical replacement.

Do not replace with any other type of lamp and do not ﬁ

t a lamp with a higher rating.

7 GUARANTEE AND AFTER SALES SERVICE

• In the event of any malfunction or anomaly, notify your ﬁtter who will have to check the ap-

pliance and its connection.

7

• In the event of damage to the mains supply cable, this can only be replaced by at approved repair

centre appointed by the manufacturer who will have the required tools and equipment to carry out any

repairs properly. Repairs carried out by other persons will invalidate the guarantee.

• Use only genuine spare parts. Should these warnings fail to be observed it could affect the safety of

your cooker hood.

• When ordering spare parts quote the model number and serial number written on the rating plate,

which is found on the casing behind the grease ﬁlters inside the hood.

• Proof of purchase will be required when requesting service. Therefore, please have your receipt

available when requesting service as this constitutes the date from which your guarantee commenced.

This Guarantee does not cover :

- Damage or calls resulting from transportation, improper use or neglect, the replacement of any light

bulbs or ﬁlters or removable parts of glass or plastic.

These items are considered to be consumable under the terms of this guarantee.

8 REMARKS

This appliance complies with European regulations on low voltages Directive 2006/95/CE on electrical

safety

, and with the following European regulations: Directive 2004/108/CE on electromagnetic compat-

ibility and Directive 93/68 on EC marking.

When this crossed-out wheeled bin symbol

is attached to a product it means the product is cov-

ered by the European directive 2002/96/EC.Your product is designed and manufactured with high quality

materials and components, which can be recycled and reused.Please inform yourself about the local

separate collection system for electrical and electronic product. Please act according to your local rules

and do not dispose of your old products with your normal household waste. The correct disposal of your

old product will help prevent potential negative consequences for the environment and human health.

GB

Page is loading ...

21

1a

525

350

725

ACTIS

PRO 57

ACTIS PRO 77

2

22

1b

1

2

3

4

23

ACTIS Pro 57_77

381

Ø150

22

813

5604

608 - 408

719 - 519

734 - 534

765 - 565

272

97

°02

60

812

331

357

404

COTE ENCASTREMENT PLANCHER : 725 - 525 x 350 mm

24

ACTIS Pro 57_77 SM

404

765 - 565

734 - 534

719 - 519

608 - 408

331

196

357

404

04

56

44

COTE ENCASTREMENT PLANCHER : 725 - 525 x 350 mm

25

3

5403003

ACCESSOIRES

ACCESSORIES

ZUBEHÖRE

ACCESSORI

ACCESORI

ACCESSOIRES

12EC003

Page 1/1

MAJ (UPDATE) : 06/12/06

ACTIS Pro 57 - 77

depuis : Janvier 2007

( From)

3S_Actis_Pro_57_77_V2007-01

AZUR - AZUR - AZUR BLAU

BLACK - NOIR- SCHWARZ

BLUE - BLEU - BLAU

BROWN - BRUN - BRAUN

GREEN YELLOW - VERT JAUNE - GRÜN GELB

GREY - GRIS - GRAU

LIGHT BLUE - BLEU CLAIR - HELL BLAU

PINK - ROSE - ROSA

PURPLE - MAUVE - MALVER FARBIG

WHITE - BLANC - WEISS

YELLOW - JAUNE - GELB

Light-Blue

Braun

Green-Yellow

kca l B

ye rG

e t i hW

nuarB

wo lleY

ruzA

Fµ 01

V 004

M

350 W

50/60 Hz

Fµ 01

V 052

1

2

3

4

56

kca l B

Braun

Blue

White

Grey

Blue

Pink

1

2

3

4

56

1

2

3

4

5

6

kca l B

nua rB

eulB

e t i hW

Grey

ye rG

G-Y

Ballast + Eclairage Fluorescent Compact

Fluorescent compact + ballast

Kompakt Neon-Beleuchtung

2 x 9 W

27

UK ELECTRICAL CONNECTION

ELECTRICAL REQUIREMENTS

Any permanent electrical installation must comply

with the latest I.E.E. Regulations and local Electricity

Boa

rd regulations. For your own safety this should be

unde

rtaken by a qualified electrician e.g. your local

Elec

tricity Board, or a contractor who is on the roll of

the

National Inspection Council for Electrical

Inst

allation Contracting (NICEIC).

ELECTRICAL CONNECTION

Before connecting to the mains supply ensure that

the mains voltage corresponds to the voltage on the

rat

ing plate inside the cooker hood.

This appliance is fitted with a 2 core mains cable and

must be permanently connected to the electricity supply

via

a double-pole switch having 3mm minimum contact

gap

on each pole. A Switched Fuse Connection Unit

to

BS.1363 Part 4, fitted with a 3 Amp fuse, is a

reco

mmended mains supply connection accessory to

ens

ure compliance with the Safety Requirements

appl

icable to fixed wiring instructions.

The wires in this mains

lead are coloured in

acco

rdance with the

following code:

Blue Neutral

Brown Live

As the colours of the wires

in the mains lead of this

appliance may not

corr

espond with the

coloured markings

iden

tifying the terminals in

your connection unit,

pro

ceed as follows:-

The wire which is coloured blue must be connected

to the terminal which is marked with the letter ‘N’ or

coloured black.

The wire which is coloured brown must be connected

to the terminal which is marked with the letter ‘L’ or

coloured red.

CH

Fiche de sécurité class 1, 250 V~ 10A

2 poles + terre.

Stecker der Schutzklasse 1, 250 V~ 10A

Zweipolig mit Schutzkontakt (Erde).

Spira di sicurezza classe 1, 250 V~ 10A

2 poli + terra

SEV 1011, SN416534-2, CH-Typ 12

Green & Yellow Earth

Page is loading ...

29

Lumière

Lighting

Beleuchtung

Illumonazione

Iluminación

Licht

12EC003

30

Numéro de série

Serial number

Seriennummer

Numero di serie

Numero de serie

Serienummer

Modèle

Model

Modell

Modello

Modelo

Model

Plaque Signalétique de la hotte

Rating plate of the cookerhood

Typenschild im Inneren der Dunstesse

Etichetta all'interno della cappa

Etiqueta de la campana

Typeplaatje van de afzuigk

ap

20NO175 - 090529

FRANKE France S.A.S.

25 Rue des Rosiers - Sainte Cécile

B. P. 56

50800 VILLEDIEU-LES-POËLES - France

Tél. 02 33 91 26 50 - Fax 02 33 51 54 79 - e-mail : com.fr[email protected]

For outside France : Tel. +33 (0)2 33 91 26 57 - Fax. : +33 (0)2 33 51 54 79

e-mail : com.expor[email protected]

ROBLIN ACTIS PRO 77 Owner's manual

This manual is also suitable for

ROBLIN ACTIS PRO 77 Owner's manual

in other languages

Related papers

Other documents