2. EAST COAST
  3. Vienna

EAST COAST Vienna Assembly And Care Instructions

  • Hello! I am an AI chatbot trained to assist you with the EAST COAST Vienna Assembly And Care Instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
VIENNA
Swinging Crib
Assembly and care
instructions
T-Nut x 2
Metal Washer x 2
Hexagon Key x 2
Upright (2)
End (2)
Foot (2)
Base (1)
Crossbar (1)
Side (2)
Barrel Nut x 12
Metal Tube x 2
Short Bolt x 4
(30mm)
Wooden Spacer x 2
Lock Mechanism x1
Lock Handle x 1
Medium Bolt x 12
(60mm)
Long Bolt x 2
(65mm)
IMPORTANT. RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY
Please read the instructions and warnings carefully before use to ensure safe and satisfactory operation
of this product.
Thiscribshouldbeassembledbyanadult,preferablywiththehelpofanassistant.
Pleasenotethatacross-headed and a flat bladed screwdriver will be required to complete the assembly
of this product.
Allfittingsshouldalwaysbefullytightened.Takecarethatnofittingsareloose,becauseachildcould
trappartsofthebodyorclothing(e.g.strings,necklaces,ribbonsforsoothersetc),whichwouldposea
riskof strangulation.
Lay out the parts on a soft level surface and compare to the part/fixing checklist below. Do not discard
any packaging until you are sure that you have all the parts.
Keep children clear during assembly as pack contains small parts which may present a choking hazard.
You will need the following tools to complete assembly:
Flat-headed screwdriver. Cross-headed screwdriver.
Hardware
2
Assembly 1
Assembly 3
Assembly 2
Upright
Lock Mechanism
Woodscrew
x 2
Lock Handle
Lock Mechanism
Upright
(NOTE: Lock
position)
Medium Bolt x 2
Crossbar
Foot
Short Bolt x 2
Foot
Upright
Short Bolt x 2
Medium Bolt x 2
Barrel
Nut x 4
3
Side (x2)
Assembly 5
Assembly 4
Barrel nut (x 4
per side)
End
Side
Medium
Bolt x 4
NOTE:
Ensure that the slot in the end of
the Barrel nut is visible and aligned
with the hole in the end of the Side.
Side
Ensure slots are at
lower edge.
4
Assembly 6
Assembly 7
Base
Medium Bolt x 4
End
Wooden Spacer
Metal Tube
NOTE:
Push the metal tube into
the hole in the End from the
outside and slide the
Wooden Spacer over it.
Repeat for other End.
5
Assembly 8
Assembly 9
Metal Washer
Long Bolt
T-Nut
NOTES:
1. Insert metal washer between
Upright and Wooden Spacer.
2. Push Long Bolt through
Upright, Metal Washer, Wooden
Spacer and Metal Tube.
3. Attach T-Nut to the end of the
Long Bolt.
4. Tighten using one hexagon key
in the Long Bolt and the other
in the T-Nut.
5. Repeat on other End.
Upright
Wooden Spacer
End
6
Long Bolt
Upright
Metal Washer
Wooden Spacer
Metal Tube
T-Nut
NOTE:
To unlock the crib body and allow it to rock, pull the lock handle out and give 1/4 turn in either
direction.
To lock the body to the frame, pull back on the Locking handle and give a further 1/4 turn and
release. Ensure that the end of the Lock has engaged in the hole in the End.
If you leave your child in this product unsupervised, you should always make sure that the lock is
engaged to prevent the crib from swinging.
End
Assembly 10
In Use
7
7195_V2
For customer care or enquiries:
Call: 01692 408802
Email: nursery@east-coast.co.uk
East Coast Nursery Ltd. Robertson House, North Walsham,
Norfolk, NR28 0BX
eastcoastnursery.co.uk
Care and maintenance
In use
Regularlycheckforfirmnessofscrewsordamagewhichcouldrenderyourswingingcribunsafeor
cause splinters.
Tocleanuseadampcloth,avoidingtheuseofstrongdetergentsorabrasives.
Anoccasionallightapplicationofawaxpolishwillhelpmaintainagoodappearance.
To operate the locking mechanism on your crib, twist the lock handle a quarter turn in either direction
and release. The lock will engage in the small hole in the bottom of the crib side and prevent it from
swinging. To unlock the crib and allow it to swing, pull the lock handle outward and twist it a quarter turn
in either direction.
If you leave your child in this product unsupervised, you should always make sure that the lock is
engaged to prevent the crib from swinging.
WARNING:YOURCHILDREN’SSAFETYISYOURRESPONSIBILITY
Thiscribshouldonlybeusedonastable,levelhorizontalfloor.
Donotallowyoungchildrentoplayunsupervisedinthevicinityofthecrib.
Donotusethecribifanypartsaremissingorbroken.
Whenachildisabletosit,kneelorpullitselfup,thecribshallnotbeusedanymoreforthischild.
Donotusethebodyofthecribwithouttheframe.
Suitable for a mattress with maximum dimensions of 88.5 x 39.5cm.
Thethicknessofthemattresstobeusedshallnotreducetheinternalverticalheightaboveittolessthan
200mm. This is indicated by a small mark on the side of the crib.
Donotplacethecribinthevicinityofanopenfireorotherstrongsourcesofheatsuchaselectricbar
fires, gasheatersetc.
ThisproducthasbeendesignedandmanufacturedtomeetBS EN 1130:1997.
/