Mittler Bros. Machine & Tool 50320 Operating instructions

50320
Mittler Bros. Machine & Tool
Brand
Mittler Bros. Machine & Tool
Model
50320
Type
Operating instructions

This manual is also suitable for

Mittler Bros. Machine & Tool Tanner RaceScale 50320 is a wireless race car scale system that allows you to accurately measure the weight distribution of your race car. The system includes four scale pads, a handheld display unit, and a communications cable. The scale pads are placed under each tire of the race car and transmit weight data to the handheld display unit. The display unit shows the weight on each wheel, the total weight of the car, and the percentage of weight on each axle.

Mittler Bros. Machine & Tool Tanner RaceScale 50320 is a wireless race car scale system that allows you to accurately measure the weight distribution of your race car. The system includes four scale pads, a handheld display unit, and a communications cable. The scale pads are placed under each tire of the race car and transmit weight data to the handheld display unit. The display unit shows the weight on each wheel, the total weight of the car, and the percentage of weight on each axle.

RaceScale
Instructions
FOR FURTHER TECHNICAL ASSISTANCE CONTACT:
TANNER RACING PRODUCTS
10 COOPERATIVE WAY
WRIGHT CITY, MO. 63390
800-558-4112 / 636-745-7757
TannerRacing.com
MittlerBros.com
WIRELESS
1. Set all scale pads out individually.
2. Turn on each pad by switching the battery switch to "ON" and press the reset
button on the front of the black box. (Green light will start blinking indicat-
ing power is on, a few seconds later the red light will blink indicating pads
are transmitting)
3. Turn the hand held on by pushing the "ON/OFF" Button. Give the hand held
a few seconds to start communication with the scale pads.
4. When numbers appear on the scaling screen the scales are ready to use.
Zero the system by pushing the "MENU" button and select zero all pads.
If you are not using all pads you may individually zero each pad. After you
highlight your choice on the menu you may select it by pushing the "OK"
button. This will then display zero's on the locations selected. (this may take a
few seconds)
5. Put your racecar on the scales and the weights will register, the %'s and
totals will show on the displays.
6. Turn the hand held off by pushing the "ON/OFF" button for 2 seconds and
the scales will turn off.
7. Turn the scale pads off to conserve battery life.
8. The hand held unit contains rechargeable batterys, simply recharge by
plugging the power adapter in to the unit. Each scale pad contains (4) AA
batterys. Frequency Change /
Pad Location Change
If you discover that there is interference with the scale pads "talking" to the
hand held or you wish to change a pad location (ex. change the RF to the LR etc.)
this can be changed by following these steps.
1. Turn each pad on and press the reset button on the front of the black box.
(Green light will start blinking indicating power is on, a few seconds later
the red light will blink indicating pads are transmitting)
2. Turn the hand held on by pushing the "ON/OFF" Button. Give the hand held
a few seconds to start communication with the scale pads.
3. Press "MENU" on the hand held and select SYSTEM ID. Scroll down to the
word ID and over to where the name is. You can change this ID to whatever
name you wish using the arrows, this will make your system unique so no
one else with a wireless scale system can pick up on your "channel" and
see your weights. Once you are finished select "OK".
4. Press "MENU" on the hand held and select RF Frequency. Give the unit a few
seconds to scan the channels and you will see numbers appear under ACTIV-
ITY. You will want to select the frequency with the lowest number (least
amount of interference).
5. Once you have selected a frequency, plug the communications cable into one
of the scale pads and the hand held.
6. Press MENU and select PAD SET UP. This will allow you to change pad
location if you wish. Whenever you change frequency, you should always
plug the cable into each scale pad and reset each one to its location. (even if
the location is not changed this will download the new frequency informa
tion)
7. Turn the scale pads and hand held off to conserve battery life.
Button Operation
Scaling Instructions
TURNS UNIT ON OR OFF
PICKS SELECTED FUNCTION
DISPLAYS THE MENU
TURNS BACKLIGHT ON SCROLLING ARROWS
If you have any questions or need technical assistance please
call 800-558-4112. Thank you and good luck racing.
  • Page 1 1
  • Page 2 2

Mittler Bros. Machine & Tool 50320 Operating instructions

50320
Mittler Bros. Machine & Tool
Brand
Mittler Bros. Machine & Tool
Model
50320
Type
Operating instructions
This manual is also suitable for

Mittler Bros. Machine & Tool Tanner RaceScale 50320 is a wireless race car scale system that allows you to accurately measure the weight distribution of your race car. The system includes four scale pads, a handheld display unit, and a communications cable. The scale pads are placed under each tire of the race car and transmit weight data to the handheld display unit. The display unit shows the weight on each wheel, the total weight of the car, and the percentage of weight on each axle.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents