Konica Minolta bizhub PRESS C8000 Safety Information Manual

bizhub PRESS C8000 contents-1

Contents

1 Introduction

1.1 Welcome .......................................................................................................................................... 1-2

1.1.1 Composition of User's Guide............................................................................................................. 1-2

1.2 Legal Restrictions on Copying....................................................................................................... 1-3

2 Precautions for Installation and Use

2.1 Safety Information........................................................................................................................... 2-2

2.1.1 Disassemble and Modification........................................................................................................... 2-3

2.1.2 Power Cord........................................................................................................................................ 2-3

2.1.3 Power Source .................................................................................................................................... 2-3

2.1.4 Power Plug......................................................................................................................................... 2-4

2.1.5 Grounding .......................................................................................................................................... 2-4

2.1.6 Installation.......................................................................................................................................... 2-4

2.1.7 Ventilation .......................................................................................................................................... 2-5

2.1.8 Actions in Response to Troubles ....................................................................................................... 2-5

2.1.9 Consumables ..................................................................................................................................... 2-5

2.1.10 When Moving the Machine ................................................................................................................ 2-6

2.1.11 When using the machine.................................................................................................................... 2-6

2.1.12 Before Successive Holidays .............................................................................................................. 2-6

2.1.13 Paper.................................................................................................................................................. 2-6

2.1.14 Paste Pellet ........................................................................................................................................ 2-6

2.1.15 Perfect Binder .................................................................................................................................... 2-7

2.1.16 Authentication Unit (IC Card Type) AU-201 ....................................................................................... 2-7

2.2 Regulation Notices.......................................................................................................................... 2-8

2.2.1 Laser Safety ....................................................................................................................................... 2-8

2.2.2 Ozone Release................................................................................................................................... 2-9

2.2.3 Electromagnetic Interference............................................................................................................. 2-9

2.3 Warning and Caution Labels........................................................................................................ 2-11

2.3.1 Caution Label on Fixing Unit............................................................................................................ 2-11

2.3.2 Caution Label on Fixing Conveyance Unit....................................................................................... 2-12

2.3.3 Caution Label on Hinges of ADF...................................................................................................... 2-12

2.3.4 Caution Label on Toner Recovery Box ............................................................................................ 2-13

2.3.5 Caution Label on 2nd Fusing Unit EF-101....................................................................................... 2-14

2.3.6 Caution Label on Perfect Binder PB-503......................................................................................... 2-15

2.3.7 Caution Label on Finisher FS-621 ................................................................................................... 2-16

2.3.8 Caution Labels on Multi Punch GP-501 .......................................................................................... 2-17

2.4 Installation Space.......................................................................................................................... 2-18

2.5 Operation Precautions.................................................................................................................. 2-34

contents-2 bizhub PRESS C8000

MEMO

1

Introduction

Welcome

1

1-2 bizhub PRESS C8000

1.1

1 Introduction

1.1 Welcome

Thank you for purchasing this machine.

This User's Guide describes the functions, operating instructions, precautions for correct operation, and sim-

ple troubleshooting guidelines of this machine. In order to obtain maximum performance from this product

and use it effectively, please read this User's Guide as necessary.

1.1.1 Composition of User's Guide

Printed manuals Overview

[Operation Quick Guide] This guide mainly describes how to use frequently

used functions. Please refer to this guide for quick

comprehension of various features available on the

machine.

[Safety Information] This guide provides precautions and requests that

should be followed to ensure safe usage of this ma-

chine.

Please be sure to read this guide before using the ma-

chine.

User's guide CD manuals Overview

[User's Guide - Main Body] This guide describes an outline of the machine and

print operations.

• Configuration and specifications of the main body

and options

• Turning on/off the machine

• Paper information

• Printing operations

• Supplies, disposals, and handling

• Troubleshooting

• Both Sides Adjustment, Curl Adjustment

• Controller Settings

• Adjustment, Utility Menu Screen

• Network Settings, PageScope Web Connection

• Web Utilities

[User's Guide - Copier] This guide describes copy operations available on the

machine with the optional Paper Feeder Unit (with

scanner) PF-705 equipped.

• Making a basic copy and setting procedures

•Quality Adjustment

• Application, Output Setting, and advanced infor-

mation

• Troubleshooting related to copy operations

• Settings on Adjustment and Utility Menu screens

related to copy operations

• Specifications of the main body and ADF config-

ured with the optional Paper Feeder Unit (with

scanner) PF-705

[User's Guide - Printer (IC-601)] This guide describes the settings of the printer drivers

and utility tool of IC-601.

• Adobe PS driver

• PostScript3 Plug-in driver

• XPS driver

• PageScope Web Connection

bizhub PRESS C8000 1-3

1.2 Legal Restrictions on Copying

1

1.2 Legal Restrictions on Copying

Certain types of original must never be copied with the purpose or intent to pass copies of such documents

off as the originals.

The following is not a complete list, but is meant to be used as a guide to responsible copying.

Financial Instruments

- Personal checks

- Traveler’s checks

- Money orders

- Certificates of deposit

- Bonds or other certificates of indebtedness

- Stock certificates

Legal Documents

- Food stamps

- Postage stamps (canceled or uncanceled)

- Checks or drafts drawn by government agencies

- Internal revenue stamps (canceled or uncanceled)

- Passports

- Immigration papers

- Motor vehicle licenses and titles.

- House and property titles and deeds

General

- Identification cards, badges, or insignias

- Copyrighted works without permission of the copyright owner

In addition, it is prohibited under any circumstances

to copy domestic or foreign currencies, or works of art

without permission of the copyright owner.

When in doubt about the nature of a document, consult with legal counsel.

This machine provides the section management function to forbid the user operating the machine without

entering a pre-established password, in order to prevent any misapplication of the machine.

Also, this section management function can limit the machine operation depending on the section, using the

setting to permit/prohibit copying, printing, or scanning.

This machine also provides the forgery prevention function in order to prevent financial instruments from be-

ing copied illegally.

We appreciate your understanding that the copied image may have some noise due to this forgery prevention

function.

[User's Guide - Network Scanner (IC-306)] This guide describes the operation of network scan-

ner functions using IC-306.

•Scan to E-mail

•Scan to HDD

• Scan to FTP

•Scan to SMB

• Scan to Queue

[User's Guide - Network Scanner (IC-601)] This guide describes the operation of network scan-

ner functions using IC-601.

•Scan to E-mail

•Scan to HDD

• Scan to FTP

•Scan to SMB

[User's Guide - Security] This guide describes the security functions.

Please refer to this guide for how to use the Enhanced

Security mode, and for detailed machine operation in

Enhanced Security mode.

[Trademarks/Copyrights] This guide describes trademarks, licenses, and copy-

rights concerning this machine.

Please be sure to read this guide before using the ma-

chine.

User's guide CD manuals Overview

Legal Restrictions on Copying

1

1-4 bizhub PRESS C8000

1.2

MEMO

2

Precautions for

Installation and Use

Safety Information

2

2-2 bizhub PRESS C8000

2.1

2 Precautions for Installation and Use

2.1 Safety Information

This section contains detailed instructions on the operation and maintenance of this machine. To achieve op-

timum utility of this device, all operators should carefully read and follow the instructions in this manual.

Please read the following section before connecting the machine to the supply. It contains important infor-

mation related to user safety and preventing equipment problems.

Please keep this manual in a handy place near the machine.

Make sure you observe all of the precautions appear in each section of this manual.

d Reference

Some parts of the contents of this section may not correspond with the purchased product.

Warning and precaution symbols

The following indicators are used on the warning labels or in this manual to categorize the level of safety warn-

ings.

Meaning of symbols

Ignoring this warning could cause serious injury or even death.

Ignoring this caution could cause injury or damage to property.

A triangle indicates a danger against which you should take precaution.

This symbol warns against cause burns.

A diagonal line indicates a prohibited course of action.

This symbol warns against dismantling the device.

A solid circle indicates an imperative course of action.

This symbol indicates you must unplug the device.

bizhub PRESS C8000 2-3

2.1 Safety Information

2

2.1.1 Disassemble and Modification

2.1.2 Power Cord

2.1.3 Power Source

Do not attempt to remove the covers and panels which have

been fixed to the product. Some products have a high-volt-

age part or a laser beam source inside that could cause an

electrical shock or blindness.

Do not modify this product, as a fire, electrical shock, or

breakdown could result. If the product employs a laser, the

laser beam source could cause blindness.

Do not scratch, abrade, place a heavy object on, heat, twist,

bend, pull on, or damage the power cord. Use of a damaged

power cord (exposed core wire, broken wire, etc.) could re-

sult in a fire or breakdown.

Should any of these conditions be found, immediately turn

OFF the power switch, unplug the power cord from the pow-

er outlet, and then call your authorized service representa-

tive.

Use only the power source voltage specified on the machine.

Failure to do that could result in a fire or electrical shock.

Do not use a multiple outlet adapter to connect any other ap-

pliances or machines. Use of a power outlet for more than the

marked current value could result in a fire or electrical shock.

Do not use an extension cord in principle. Use of an exten-

sion cord could cause a fire or electrical shock. Contact your

authorized service representative if an extension cord is re-

quired.

The outlet must be near the equipment and easily accessible.

Otherwise you can not pull out the power plug when an emer-

gency occurs.

Safety Information

2

2-4 bizhub PRESS C8000

2.1

2.1.4 Power Plug

2.1.5 Grounding

2.1.6 Installation

Do not unplug and plug in the power cord with a wet hand,

as an electrical shock could result.

Plug the power cord all the way into the power outlet. Failure

to do this could result in a fire or electrical shock.

Do not tug the power cord when unplugging. Pulling on the

power cord could damage the cord, resulting in a fire or elec-

trical shock.

Remove the power plug from the outlet more than one time a

year and clean the area between the plug terminals. Dust that

accumulates between the plug terminals may cause a fire.

Do not place any objects around the power plug, as the pow-

er plug may be difficult to pull out when an emergency oc-

curs.

Connect the power cord to an electrical outlet that is

equipped with a grounding terminal.

Do not place a flower vase or other container that contains

water, or metal clips or other small metallic objects on this

product. Spilled water or metallic objects dropped inside the

product could result in a fire, electrical shock, or breakdown.

Should a piece of metal, water, or any other similar foreign

matters get inside the product, immediately turn OFF the

power switch, unplug the power cord from the power outlet,

and then call your authorized service representative.

Do not use flammable sprays, liquids, or gases inside or near

this machine. Do not clean the inside of this machine using a

flammable gas duster. A fire or explosion could result.

After installing this product, mount it on a secure base. If the

unit moves or falls, it may cause personal injury.

Do not place the product in a dusty place, or a site exposed

to soot or steam, near a kitchen table, bath, or a humidifier.

A fire, electrical shock, or breakdown could result.

Do not place this product on an unstable or tilted bench, or

in a location subject to a lot of vibration and shock. It could

drop or fall, causing personal injury or mechanical break-

down.

Do not let any object plug the ventilation holes of this prod-

uct. Heat could accumulate inside the product, resulting in a

fire or malfunction.

bizhub PRESS C8000 2-5

2.1 Safety Information

2

2.1.7 Ventilation

2.1.8 Actions in Response to Troubles

2.1.9 Consumables

Using this product in a poorly ventilated room for a long time

or producing a large volume of copies or prints may cause

the odor of exhaust air from the machine. Ventilate the room

well.

Do not keep using this product, if this product becomes inor-

dinately hot or emits smoke, or unusual odour or noise. Im-

mediately turn OFF the power switch, unplug the power cord

from the power outlet, and then call your authorized service

representative. If you keep on using it as is, a fire or electrical

shock could result.

Do not keep using this product, if this product has been

dropped or its cover damaged. Immediately turn OFF the

power switch, unplug the power cord from the power outlet,

and then call your authorized service representative. If you

keep on using it as is, a fire or electrical shock could result.

The inside of this product has areas subject to high temper-

ature, which may cause burns.

When checking the inside of the unit for malfunctions such as

a paper misfeed, do not touch the locations (around the fus-

ing unit, etc.) which are indicated by a "Caution HOT" caution

label.

Do not throw toner containers (toner bottles) into an open

flame. The hot toner may scatter and cause burns or other

damage.

Do not leave toner-related parts (toner bottles or drum units)

within easy reach of children. Licking any of these parts or in-

gesting toner could damage your health.

Do not store toner-related parts (drum units or developing

units) near devices susceptible to magnetism, such as preci-

sion equipment and data storage devices. They could cause

these products to malfunction.

Safety Information

2

2-6 bizhub PRESS C8000

2.1

2.1.10 When Moving the Machine

2.1.11 When using the machine

2.1.12 Before Successive Holidays

2.1.13 Paper

2.1.14 Paste Pellet

Whenever moving this product, be sure to disconnect the

power cord and other cables. Failure to do this could damage

the cord or cable, resulting in a fire, electrical shock, or

breakdown.

Do not move this product. If it is moved or falls, it may cause

severe personal injury.

When using the machine, do not look at the light of the lamp

for a prolonged time. Eyestrain could result.

Unplug the product when you will not use the product for

long periods of time.

Do not use stapled paper, conductive paper (such as silver

paper or carbon paper) or treated heat-sensitive/inkjet paper,

otherwise a fire may result.

Do not put paste pellets close to fire. Paste pellets are flam-

mable and easy to catch on fire.

Do not swallow paste pellets. Should you swallow any, drink

large amount of water or milk to vomit, and immediately con-

sult a doctor.

Keep out of reach of children in order to avoid unexpected

accidents.

bizhub PRESS C8000 2-7

2.1 Safety Information

2

2.1.15 Perfect Binder

2.1.16 Authentication Unit (IC Card Type) AU-201

Do not use the perfect binder without ventilation for an ex-

tended period of time. Ensure to ventilate the room on a reg-

ular basis. It is recommended that the perfect binder should

be installed in a place with a local exhaust system. Using the

perfect binder in a room without appropriate ventilation could

pose health hazard.

Handle melted hot paste carefully. If it gets in the eye, do not

rub nor tray to open the eye, but cool it with cold water im-

mediately and consult a doctor.

Do not touch melted hot paste as it may cause burn injury. If

it sticks on your skin, cool that part of the skin with cold water

immediately and consult a doctor.

Do not touch the paste tank unit immediately after you turned

off the machine to avoid burn injury. Wait until the unit is no

longer hot when you handle it directly with your hands.

Do not put the paste hopper and the paste tank unit close to

fire. Paste is flammable and easy to catch on fire.

Do not get close to the vapor emitted from melted hot paste.

If you have irritation in or around your eyes, nose or throat,

move to an area where you can get fresh air.

Do not block up the vent for the fan on the back of the perfect

binder. This will prevent the discharge of heat, and may

cause fire or breakdown.

Do not change the temperature setting for the paste tank

unit. This may cause fire or breakdown.

Do not use this product near water, otherwise it may be dam-

aged.

Do not cut, damage, modify or forcefully bend the USB cable.

A malfunction may occur as a result of a damaged or cut UBS

cable.

Do not diassembly this device, otherwise it may be damaged.

Do not store the IC card within 40 mm of the card scanning

area.

Regulation Notices

2

2-8 bizhub PRESS C8000

2.2

2.2 Regulation Notices

2.2.1 Laser Safety

This product employs a Class 3B laser diode having maximum power of 15 mW and wavelength of 775-800

nm.

This product is certified as a Class 1 laser product. Since the laser beam is concealed by protective housings,

the product does not emit hazardous laser radiation as long as the product is operated according to the in-

structions in this manual.

- For Denmark Users

ADVARSEL

Usynlig laserstråling ved åbning, når sikkerhedsafbrydere er ude af funktion.

Undgå udsættelse for sråling.

Klasse 1 laser produkt der opfylder IEC 60825-1 sikkerheds kravene.

Dansk: Dette er en halvlederlaser. Laserdiodens højeste styrke er 15 mW og bølgelængden er 775-800 nm.

- For Norway Users

ADVARSEL

Dersom apparatet brukes på annen måte enn spesifisert I denne bruksanvisning, kan brukeren utsettes for

usynlig laserstråling som overskrider grensen for laser klass 1.

Dette en halvleder laser. Maksimal effekt till laserdiode er 15 mW og bøkgelengde er 775-800 nm.

bizhub PRESS C8000 2-9

2.2 Regulation Notices

2

- For Finland, Sweden Users

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

VAROITUS!

Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisu-

usluokan 1 ylittävälle näkymättömälle lasersäteilylle.

Tämä on puolijohdelaser. Laserdiodin suurin teho on 15 mW ja aallonpituus on 775-800 nm.

VARNING!

Om apparaten används på annat sätt än I denna bruksanvisning specificerats, kan användaren utsättas för

osynlig laserstrålning, som överskrider gränsen för laserklass 1.

Det här är en halvledarlaser. Den maximala effekten för laserdioden är 15 mW och våglängden är 775-800 nm.

2.2.2 Ozone Release

During print operation, a small quantity of ozone is released. This amount is not large enough to harm anyone

adversely. However, be sure the room where the machine is being used has adequate ventilation, especially

if you are printing a high volume of materials, or if the machine is being used continuously over a long period.

2.2.3 Electromagnetic Interference

This product must be used with a shielded network cable and shielded USB interface cable.

The use of non-shield cables is likely to result in interference with radio communications and is prohibited

under CISPR 22 and local rules.

For European Users

This product complies with the following EU directives:

89/336/EEC, 73/23/EEC and 93/68/EEC

This declaration is valid for the areas of the European Union (EU) or EFTA only.

This device must be used with a shielded network cable and shielded USB interface cable. The use of non-

shielded cables is likely to result in interference with radio communications and is prohibited under

89/336/EEC rules.

For German Users

Maschinenlarminformations -Verordnung - 3. GSGV, 18.01.1991:

Der arbeitsplatzbezogene Immisionswert betraegt 70 dB(A) oder weniger nach ISO 7779.

Notification for US only

Contains Mercury in the LCD control panel backlighting lamp, and/or in the scanning unit lamp. Dispose Ac-

cording to Local, State or Federal Laws.

Notification for California Customers

This product uses a CR Lithium Battery which contains perchlorate material.

This perchlorate warning applies to perchlorate-containing lithium batteries sold or distributed in California,

USA.

"Perchlorate Material - Special handling may apply, See www.dtsc.ca.gov/ hazardouswaste/perchlorate

."

Regulation Notices

2

2-10 bizhub PRESS C8000

2.2

CE Marking (Declaration of Conformity) for Users of the European Union (EU)

This product complies with the following EU directives:

89/336/EEC, 73/23/EEC and 93/68/EEC directives.

This declaration is valid for the area of the European Union.

This device must be used with a shielded network (10 Base-T/100 Base-TX) cable and a shielded parallel ca-

ble. The use of non-shielded cables is likely to result in interference with radio communications and is pro-

hibited under CISPR rules and local rules.

USER INSTRUCTIONS FCC PART 15 - RADIO FREQUENCY DEVICES (For U.S.A. Users)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

this device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interfer-

ence to radio communications. Operation of this equipment in a residential area is likely to cause harmful in-

terference in which case the user will be required to correct the interference at his own expense.

WARNING:

The design and production of this unit conform to FCC regulations, and any changes or modifications must

be registered with the FCC and are subject to FCC control. Any changes made by the purchaser or user with-

out first contacting the manufacturer will be subject to penalty under FCC regulations.

This device must be used with a shielded network (10 Base-T/100 Base-TX) cable and a shielded parallel ca-

ble. The use of non-shielded cables is likely to result in interference with radio communications and is pro-

hibited under FCC rules.

INTERFERENCE-CAUSING EQUIPMENT STANDARD (ICES-003 ISSUE 5) (For Canada Users)

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

This device complies with Canadian RSS-Gen.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this

device must accept any interference, including interference that may cause undesired operation of this de-

vice.

Cet appareil est conform à la norme CNR-Gen du Canada.

L’utilisation de ce dispositif est autorisée seulement aux deux conditions suivantes : (1) il ne doit pas produire

de brouillage, et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu,

même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.

For Users in countries not subject to Class B regulations

WARNING:

This is a Class A product. In a domestic environment this product may cause radio interference in which case

the user may be required to take adequate measures.

This device must be used with a shielded network (10 Base-T/100 Base-TX) cable and a shielded parallel ca-

ble. The use of non-shielded cables is likely to result in interference with radio communications and is pro-

hibited under CISPR rules and local rules.

LED radiation safety

This product is a machine which operates by means of a LED (light emitting diodes) exposure system. There

is no possibility of danger from the LED optical radiation, because the LED optical radiation level does not

exceed the accessible radiation limit of class 1 under all conditions of operation, maintenance, service and

failure.

bizhub PRESS C8000 2-11

2.3 Warning and Caution Labels

2

2.3 Warning and Caution Labels

This machine has warning label, caution labels and indicators for safety precaution in the following location.

These labels and indicators advise you to pay special attention to avoid any dangerous situations or serious

injury when you replace the units.

7 CAUTION

Do not remove warning or caution labels!

- Should any warning or caution label be removed, you may fail to check a specific part to be alert for

unexpected trouble or injury. If you find any warning or caution label removed or illegible due to soilage,

please contact your service representative.

2.3.1 Caution Label on Fixing Unit

7 CAUTION

DO NOT touch the fusing part of the fixing unit. Otherwise, you may get burned.

- Please be especially careful in withdrawing the fixing conveyance unit.

Warning and Caution Labels

2

2-12 bizhub PRESS C8000

2.3

2.3.2 Caution Label on Fixing Conveyance Unit

7 CAUTION

DO NOT put your hand or arm between the main body and the fixing conveyance unit.

- Touching connecting terminals of electric parts may damage the machine or cause unexpected trouble.

Please do not try to work yourself, but contact your service representative.

2.3.3 Caution Label on Hinges of ADF

7 CAUTION

DO NOT insert your fingers into the two ADF hinge portions. Otherwise, you may be injured.

- Please be careful when opening or closing the ADF.

Page is loading ...

Konica Minolta bizhub PRESS C8000 Safety Information Manual

Konica Minolta bizhub PRESS C8000 Safety Information Manual

Related papers

Other documents