CUSTOMER SERVICE
GQBrands.com • CustomerService
@
GQBrands.com • 1-866-498-5269 • 4401 Samuell Blvd, Ste 150, Mesquite, TX 75149
FOR AGES:
WEIGHT LIMIT:
TO BUILD: TOOLS NEEDED:
3-7
150
Lbs
68 Kgs
X
1
Manual en
español ubicado
en GQBrands.com
Spanish Manual located
at GQBrands.com
KIDS ROCKER SEESAW
MODEL# 9306RS
PRODUCT MANUAL - VERSION 5.20.01
GQBrands.com CustomerService@GQBrands.com 1-866-498-5269
CUSTOMER SERVICE INFORMATION
Global Quality Brands® warrants this product to be free from defects in
workmanship and materials under normal use and conditions for a period of
90 DAYS FROM THE DATE OF ORIGINAL PURCHASE
. This Limited Warranty is not
transferable and is available only for the original purchaser of the Product. The
Company’s obligation under this warranty is limited to replacing or repairing the
Product, at the discretion of the company.
All warranty coverage extends only to the original retail purchaser from the date
of purchase, GQ Brands obligation under this warranty is limited to replacing or
repairing, at Global Quality Brands® option. All products for which a warranty
claim is made must be received by Global Quality Brands® and accompanied by
sufficient proof of purchase (photocopy of the original store receipt, indicating
the date of purchase). All freight and handling fees are the responsibility of the
consumer to pay, both to and from Global Quality Brands®. All warranty claims
must be preauthorized by Global Quality Brands® pre-authorization can be
obtained by calling 866-498-5269.
This warranty does not cover ordinary wear and tear, weathering, failure to follow
directions, improper installation, improper maintenance, or acts of nature, (such
as damage caused by wind, lightning, snow, water, or ice) weather damage,
damage caused by unauthorized repair work or damage caused by improper use
of the products are not covered by the product warranty. No other warranty beyond
that specifically set forth above is authorized by GQBrands®.
GLOBAL QUALITY BRANDS® IS NOT RESPONSIBLE OR LIABLE FOR INDIRECT,
SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR IN CONNECTION
WITH THE USE OR PERFORMANCE OF THE PRODUCT OR OTHER DAMAGES WITH
RESPECT TO ANY ECONOMIC LOSS, LOSS OF PROPERTY, LOSS OF REVENUE
OR PROFITS, LOSS OF ENJOYMENT OR USE, COST OF REMOVAL, INSTALLATION
OR OTHER CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES.
ACCORDINGLY,
THE ABOVE LIMITATION MAY NOT APPLY TO YOU. THE WARRANTY EXTENDED
HEREUNDER IS IN LIEU OF ALL OTHER WARRANTIES AND GLOBAL QUALITY
BRANDS®, SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED IN
ITS SCOPE AND DURATION TO THE TERMS SET FORTH HEREIN. SOME STATES
DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS.
ACCORDINGLY, THE ABOVE LIMITATION MAY NO APPLY TO YOU. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS,
WHICH VARY FROM STATE TO STATE.
WHILE EVERY ATTEMPT IS MADE TO ENSURE THE HIGHEST DEGREE OF
PROTECTION IN ALL EQUIPMENT, WE CANNOT GUARANTEE FREEDOM
OF INJURY. THE USER ASSUMES ALL RISK OF INJURY DUE TO USE. ALL
MERCHANDISE IS SOLD ON THIS CONDITION, WHICH NO REPRESENTATIVE OF
GQBRANDS® CAN WAIVE OR CHANGE.
Please be sure to include the following information when you contact Customer Service:
YOUR NAME: _________________________________________
YOUR MAILING ADDRESS: _______________________________
YOUR EMAIL ADDRESS: ________________________________
PRODUCT NAME: _____________________________________
PRODUCT MODEL#: ___________________________________
PART NUMBER _______________________________________
LIMITED WARRANTY
2
Thank you for purchasing:
KIDS ROCKER SEESAW
MODEL# 9306RS
Please do not return your item. Please report items that are
damaged or missing parts to the manufacturer GQ Brands within
3days of delivery. Contact customer service at
[email protected] to open a ticket.
At GQBrands®, we want all of our customers to be completely
satisfied with their purchase. Take time to review the contents of the
product you have just received to make sure that all of the parts are
included. If you find that any parts are missing or damaged, we will
provide replacement parts at no charge within 30 days of purchase.
Please keep in mind that for select damaged part replacement
requests, we will require a photo for submission.
To order these parts, or if you have
any other questions or concerns
about this GQBrands product, please contact us at
PureFun.Net
GQBrands®
Phone: 1-866-498-5269
Email: [email protected]
4401 Samuell Blvd, Ste 150, Mesquite, TX 75149
To register you product please visit:
www.globalqualitybrands.com/product-registration
or scan code:
RETAILER WHERE PURCHASED:_________________________
DATE OF PURCHASE: __________________________________
ORDER NUMBER: (If Available) ____________________________
QUANTITY NEEDED: __________________________________
SERIAL NUMBER:
MODEL#9306RS
WARNINGS
ADULT ASSEMBLY REQUIRED
Please read these warnings and the information in this manual in its entirety.
Failure to comply with the following instructions may increase the risk of serious injury and/or death:
CHOKING HAZARD - Small Parts
NOT for children under 3 years of age.
• Please read these warnings and the
information in this manual in its entirety.
Failure to comply with the following
instructions may increase the risk of
serious injury and/or death:
• This unit must be assembled and
disassembled by ADULTS ONLY.
• This Rocker Seesaw is suitable for use by
most children 3 to 7 YEARS OF AGE.
• DO NOT exceed the MAXIMUM WEIGHT limit
per seat of 75lbs (34kgs), regardless of age.
• DO NOT install this equipment over
concrete, asphalt, or any other hard or
rough surface. The Rocker Seesaw should
always be installed over an appropriate,
stable surface (rubber mat, grass, etc).
• ALWAYS locate this equipment on a stable,
level surface AT LEAST 7 feet away from
any structure, obstruction, or possible
hazard(s) such as walls, pools, power lines,
overhangs, other playground equipment,
driveways, hard surfaces and/or roadways.
• Children must be supervised at all times
when using this equipment. DO NOT leave
children unattended at any time.
• DO NOT attach items to the Rocker Seesaw
not specifically designed for this purpose.
Especially in the case of jump ropes, chains,
clotheslines, pet leashes and cables.
• These may cause a strangulation or physical
hazard.
• This Rocker Seesaw is NOT for adult use.
• This Rocker Seesaw is only designed for
family residential use. It is NOT intended for
commercial applications and/or use
in public areas such as schools, parks,
nurseries, day schools, day cares, etc.
• DO NOT allow more than one child per seat
on the Rocker Seesaw and/or Rocker at a
time.
• Instruct children to always be sure that the
ground underneath the seesaw is clear of
any persons, pets or obstructions before
using.
• DO NOT allow children to wear glasses or
helmets when using the Rocker Seesaw.
• Small children must be assisted by an adult
in mounting and dismounting the seesaw
seats.
• DO NOT allow children to wear loose fitting
clothing, clothing with straps/ loops,
backpacks or wear and/or hold accessories
with straps or loops, or any article of
clothing or accessory with sharp edges
which may present a hazard or become
snagged or caught on the Rocker Seesaw
during use. Serious injury and/or accidental
strangulation may occur.
• DO NOT allow people and pets to stand or
sit in or near the Rocker Seesaw play area
when the item is in motion.
• DO NOT allow children to climb or hang
from the steel tubing – this can cause
serious injury.
• This product is not to be used in
conjunction with pools, spas, or other
bodies of water.
• Children must ALWAYS remain securely
seated, firmly grasping the handrails,
and in the forward facing position when
rocking. Do not lay down, rock while
standing, or sit backwards on the seats.
• DO NOT use in adverse weather
conditions, while the seats are wet, or in
poorly lit conditions.
• ALWAYS secure the Rocker Seesaw against
unauthorized and unsupervised use.
• ALWAYS wear the appropriate footwear (i.e.
closed toe shoes) when using the Rocker
Seesaw.
• Before each use of this product, inspect
and replace any worn, defective or missing
parts. Although the Rocker Seesaw is
made to take a lot of wear, over time parts
may need to be replaced. It is important
to check the Rocker Seesaw to ensure the
Frame, Seats and Handrails are steady
and all parts are in good condition. If any
loose, cracked, missing, or otherwise
damaged components are found, cease
use of this item immediately and secure it
from unauthorized used until the issue has
been corrected and/or replacement parts
obtained.
• Please read and refer to other warnings
and use information in the Rocker Seesaw
instructions before use.
• Dispose of all packaging materials safely
and per local ordinance.
3
GQBrands.com CustomerService@GQBrands.com 1-866-498-5269
PARTS LIST
4
1 - Base Rails 2 - Foam Rocker Bar
4 - Backrest3 - Handle Tube
x2
x2
x2
x2
MODEL#9306RS
PARTS LIST
5
5 - Footrest Tube
6 - Seats
x2
x5
7 - M6 45mm Bolt
x16
8 - M6 40mm Bolt
x20
9 - M6 50mm Bolt
x4
10 - Square Nuts
x20
11 - Hex Nut
x20
12 - Washer
x20
13 - Safety Caps
x20
16 - Round Cap
x4
15 - Flat Cap (Small)14 - Flat Cap (Large)
GQBrands.com CustomerService@GQBrands.com 1-866-498-5269
ASSEMBLY INSTRUCTIONS
6
STEP 1
STEP 2
Parts:
Part 1 (x2) - Base Rails
Part 6 (x1) - Seat
Place both Base Rails (Part 1) in a flat
surface free of obstructions. Place
Seat (Part 6) with the flat surface
facing the floor and align the side
openings to the middle openings of
the Base Rails (1).
Parts:
Part 10 (x4) - Square Nuts
Part 8 (x4) - M6 40mm Bolt
Place the Square Nuts (Part 10) at the
end gaps of the Seat openings, and
secure with a M6 40mm Bolt (Part 8)
aligned by the Base Rail and Seat
openings.
NOTE:
Push the Bolt all the way until it
aligns with the opening of the Square
Nut. Tightening clockwise will help
the Square Nut reach the end of the
Seat gap.
1
10
10
8
8
1
6
MODEL#9306RS
ASSEMBLY INSTRUCTIONS
7
STEP 3
Parts:
Part 6 (x4) - Seats
Part 10 (x12) - Square Nuts
Part 8 (x12) - M6 40mm Bolt
Place the remainder of the Seats
at the end of the Base Rails with
the flat surface of the Seats facing
the floor. Place 2x on each side as
shown. Align the side openings to the
corresponding Base Rails opening.
Place the Square Nuts (Part 10) at the
end gaps of the Seat openings, and
secure with a M6 40mm Bolt (Part
8) aligned by the Base Rail and Seat
openings.
NOTE:
When Installing the Seats to the Base
Rails, do not install to the 4 locations
circled as shown. These are reserved
to install the Handle Bars in Step 12.
6
10
8
8
8
10
10
6
6
6
Do not Install
GQBrands.com CustomerService@GQBrands.com 1-866-498-5269
ASSEMBLY INSTRUCTIONS
8
STEP 4
STEP 5
Parts:
Part 2 (x2) - Foam Rocker Bar
Part 7 (x4) - M6 45mm Bolt
Part 11 (x4) - Hex nut
Part 12 (x4) - Washer
NOTE: Round Cap (Part 16) is already
installed on the Foam Rocker Bar
(Part 12). If not, slide to both ends and
make sure the tub ends are covered
Place the Foam Rocker Bars (Part 2)
on the outside of the Base Rails facing
away from the Seats.
Align the opening of the tip of the
Base Rails to the opening under the
Round Cap of the Foam Rocker Bars.
Tighten with a M6 45mm Bolt (Part
7), Hex Nut (Part 11), and Washer
(Part 12).
2
2
11
12
7
Inside the Foam Rocker Bars, there
are 8 indent locations as shown. You
can find them when pressed.
Once you have found the indent, using
a sharp Knife, cut a slit in that location
to reveal the opening on the Bar itself.
WARNING!
Cutting the slits on the Foam Rocker
Bar must be done by an adult
(+18 Years). For more information,
review The Warning and Safety
instructions on Page 5.
MODEL#9306RS
ASSEMBLY INSTRUCTIONS
9
STEP 6
Parts:
Part 3 (x2) - Handle Tube
Part 5 (x2) - Footrest Tube
Part 8 (x4) - M6 40mm Bolt
Part 11 (x4) - Hex Nut
Part 12 (x4) - Washer
Locate the middle openings in the
Handle Tube (Part 3), and align to the
openings at the tips of the Footrest
Tube (Part 5).
Tighten with a M6 40mm Bolt (Part 8),
Hex Nut (Part 11), and Washer (Part
12).
Repeat until you have 2x completed
Handle Tubes with the Footrest Tubes
installed.
3
5
8
12
11
GQBrands.com CustomerService@GQBrands.com 1-866-498-5269
ASSEMBLY INSTRUCTIONS
10
STEP 7
STEP 8
Parts:
Part 9 (x4) - M6 50mm Bolt
Part 11 (x4) - Hex nut
Part 12 (x4) - Washer
Locate the aligned middle openings in
the Handle Bar.
Tighten with a M6 50mm Bolt
(Part 9), Hex Nut (Part 11), and
Washer (Part 12).
NOTE:
Make sure the head of the Bolts are
facing the outside of the Seesaw to
avoid scratches or scrapes when in
use.
Insert the Assembled Handles on the
inside of the Seesaw.
Align the upper openings of the
Handle Tubes to the Base Rails, and
bottom openings to the Foam Rocker
Bars
11
12
9
MODEL#9306RS
ASSEMBLY INSTRUCTIONS
11
STEP 9
Parts:
Part 7 (x4) - M6 45mm Bolt
Part 11 (x4) - Hex nut
Part 12 (x4) - Washer
Locate the aligned bottom openings in
the Handle Bar.
Tighten with a M6 45mm Bolt (Part
7), Hex Nut (Part 11), and Washer
(Part 12).
Hide the head of the Bolt under the
foam of the Foam Rock Bars.
NOTE:
Make sure the head of the Bolts are
facing the outside of the Seesaw to
avoid scratches or scrapes when in
use.
11
12
7
GQBrands.com CustomerService@GQBrands.com 1-866-498-5269
12
ASSEMBLY INSTRUCTIONS
STEP 11
Parts:
Part 7 (x4) - M6 45mm Bolt
Part 11 (x4) - Hex nut
Part 12 (x4) - Washer
Tighten the tips to the foam rocker.
Hide the head of the Bolt under the
foam of the Foam Rock Bars once
installed.
NOTE:
Make sure the head of the Bolts are
facing the outside of the Seesaw to
avoid scratches or scrapes when in
use.
STEP 10
Parts:
Part 4 (x2) - Backrest
Insert the Backrest (Part 4) from the
outside of the Base Rails and slide
the tips on the inside of the Rocker
Seesaw.
Align the openings of the tips to the
Foam Rocker Bars to the Backrest to
install the hardware in Step 11.
4
4
7
12
11
MODEL#9306RS
ASSEMBLY INSTRUCTIONS
13
STEP 12
STEP 13
Parts:
Part 7 (x4) - M6 45mm Bolt
Part 10 (x4) - Square Nuts
Flip the Rocker Seesaw over to install
the Seats into the Base Rail and
Backrests.
Place the Square Nuts (Part 10) at the
end gaps of the Seat openings, and
secure with a M6 38mm Bolt (Part 8A)
aligned by the Base Rail, Backrest,
and Seat openings.
Parts:
Part 13 (x20) - Safety Caps
Use the Safety Caps (Part 13) to hide
any excess from the Bolts.
NOTE:
Failure to use the Safety may cause
scratches, scrapes, or injury while
when product is in use.
10
7
x20
GQBrands.com CustomerService@GQBrands.com 1-866-498-5269
14
FREQUENTLY ASKED QUESTIONS
Question: “How should I clean my
s
eesaw?”
Answer: you should clean the Seesaw with
a solution of warm water and Non-
Corrosive/Abrasive soap. Dampen a rag
with this solution and wipe com
pletely dry
before using.
Question: “A seat seems loose, what
s
hould I do?”
Answer: Make sure the Bolts/Nuts
under the plastic seat are secure.
CARE & MAINTENANCE
• Your Rocker Seesaw is designed to be very low
maintenance.
• If any part of the seesaw requires cleaning, simply wipe
with a damp cloth.
• Regularly check to see if the steel tubes, seats,
backrests and other parts are tightened and completely
secure. Replace worn & damaged parts if found and if
necessary, secure from use until replacement parts can
be obtained.
• If the paint is chipped, we recommend you lightly rub
the damaged area and cover using a non-toxic enamel
paint.
• IMPORTANT: While no regular maintenance is required,
you must inspect the seesaw before each use and
replace any worn, defective, or missing parts. The
following conditions could represent potential hazards:
Missing, improperly positioned, or insecurely attached
frame parts, Missing, improperly secured or damaged
seats, and/or a bent or broken rocker, Cease using
seesaw immediately and secure it against unauthorized
use if any of these conditions are present.
Question: “Something was missing
from the packaging,” “I need to
purchase a replacement part” or “I
discovered a damaged piece. What
should I do?”
Answer: Contact customer service.
You must have proof of purchase
and/or order confirmation available
to be considered for warranty
replacement. You must report
missing pieces within 30 days of
purchase.
Thank You Coupon!
As a way of saying thank you for purchasing one of our products, here is a 10% OFF coupon for
y
our next purchase at
www.PureFun.net
Use Code: GQBRANDS10 at Checkout
/
