Athena GET SL1 User manual

Type
User manual
ENGLISH
DATA LOGGER
User Manual
2
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
The content of this document, nor parts of it, may be reproduced, transferred, distributed or
stored in any form without the written permission of GET by Athena.
GET reserves the right to make changes to the content of this manual without notice.
3
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
INDEX
1 SL1 KIT 7
2 WHY ACQUIRE...
8
3 GPS SYSTEM
8
3.1 Fix GPS
9
4 NECESSARY REQUIREMENTS...
9
5 SL1: INSTALLATION
10
5.1 Installing the GPS antenna
10
5.2 Precautions
11
6 SL1: FRONT VIEW
11
7 BEFORE STARTING...
12
7.1 Installing the software (LynXLog + WinTAX Junior version)
12
7.1.1 How to activate the WinTAX4 Junior license
17
7.1.2 Software update
17
8 SL1: OPERATING DIAGRAM
19
9 BEHAVIOUR OF THE LEDs
20
10 SL1: POWER SUPPLY MANAGEMENT
21
11 LYNXLOG: SOFTWARE INTERFACE
21
11.1 LynXLog: Navigation bar
22
11.2 LynXLog: Main functions
22
11.3 LynXLog status bar
23
12 HOW TO...
23
12.1 Connecting the SL1 Data Logger to the PC
23
12.1.1 USB connection
23
12.1.2 WiFi connection
24
12.2 Setting the archive folder
26
12.3 Downloading the acquired data (Run)
28
12.4 Deleting the acquired data (Run)
29
12.5 Opening, saving and modifying the setup
30
12.5.1 Downloading the setup from SL1
31
12.5.2 Open the setup file (.set)
32
12.5.3 Sending the setup to SL1
33
12.5.4 Changing the setup
34
12.5.5 Saving the setup to a file (.set)
35
12.6 Using the Channel Real-Time Monitor
36
12.6.1 Adding a channel to the Channel Monitor list
36
12.6.2 Displaying a channel in Real-Time
37
12.6.3 Removing a channel from the Channel Monitor list
38
12.6.4 Calibrating a channel on the Channel Monitor list
39
12.6.5 Calibrating a suspension channel on the Channel Monitor list
40
12.7 Starting acquisition manually
41
12.8 Changing the SL1 Data Logger hardware settings
42
12.8.1 Changing the auto power off time
43
12.8.2 Changing the GPS dynamic
45
12.8.3 Changing the brightness of the SL1 LEDs
47
12.8.4 Turning off the SL1 Data Logger
48
12.9 Changing the Lynxlog settings
49
13 SL1 DATA LOGGER TECHNICAL SPECIFICATIONS
52
ANNEX 1 ACQUISITION SETUP DETAILS
53
1 SET INFO
54
4
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
INDEX
2 SEARCHING FOR A CHANNEL 55
3 SETTING THE TRIGGERS
56
4 AN/FRQ PANEL (PHYSICAL INPUTS: AN1..AN3, IC1)
57
5 CAN Port GET and CAN Port EXP panels
58
5.1 Adding a new CAN channel
58
5.2 Changing a CAN channel
61
6 CALIBRATING A CHANNEL
60
6.1 Calibration None
62
6.2 Linear calibration
63
6.3 Polyline calibration
64
6.4 Suspension calibration
67
7 GPS PANEL
69
8 IMU PANEL
69
9 TRACK MANAGEMENT
70
9.1 Creating your customised track
70
9.2 Sending a track to the SL1 Data Logger
74
ANNEX 2 PINOUTS
78
1 “MAIN” CONNECTOR
78
2 “EXP” CONNECTOR
78
3 “USB” CONNECTOR
79
ANNEX 3 CONNECTING THE SL1 WIRING
80
1 MAIN POWER/IC WIRING code GL-0178-AA
80
2 EXPANSION WIRING code GL-0179-AA
81
3 MULTILINK WIRING code GL-0167-AB
82
ANNEX 4 SL1 CONNECTION DIAGRAM
83
1 RX1/ GP1 ECUs - SL1 (BATTERY LESS CONFIGURATION)
83
2
APPLICATION OFFROAD CAN BUS + EXT. SENSORS: RX1/ GP1 ECUs - SL1 (CONF.
BATTERY LESS)
84
3 APPLICATION ROAD CAN BUS + EXT. SENSORS: SL1 , RX1PRO ECU, D30 DASH
85
4
APPLICATION ROAD CAN BUS + EXT. SENSORS: SL1 , ECULMB ECU (e.g. YZF-R25/
R3), D30 DASH
86
5 ANALOGUE CONNECTION LC1-EVO
87
6 SENSORS SL1 FOR TYPE
88
7 ANALOGUE SENSORS
89
8 IC SENSORS
89
5
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
Dear Customer,
Thank you for selecting a product from the GET by Athena data acquisition line.
We are sure that our passion and experience will be able to successfully reach maximum
performance in all the competitions in which you want to participate. Therefore please read this
manual as we are sur e that it can help you to properly use your new GET by Athena device.
Thanks to GPS technology, the devices in the SL1 Data Logger family are able to acquire not only
signals from the sensors connected to them, but also vehicle trajectories and speed.
The data download and configuration of the SL1 Data Logger is managed using the LynXLog
software.
The acquired data can be analysed using the WinTAX4 Junior* software.
The purpose of this manual is to illustrate the functions of the SL1 Data Logger to the end user.
*WinTAX Junior requires an activation code, to obtain it contact us at tech@athena.eu.
6
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
Nomenclature
CAN – Communication protocol.
DYNO – Test bench.
GPS – Global Positioning System is a satellite positioning and navigation system.
FIX-GPS – The fix-gps is the position that the gps module obtained calculating the distance of the
satellites.
IMU – Inertial platform, system that permits monitoring a moving vehicle using inertial sensors.
LED – Light Emitting Diode, the luminous lights on the SL1 Data Logger.
LOGGER / DATA LOGGER SL1 – Data acquisition system.
LynXLog – Software for managing the SL1 Data Logger.
OTA – Software update system (over the air).
PASSWORD- Access word.
RPM – Revolutions per minute.
RUN – Data acquisition that has a progressive number and a date.
SETUP – SL1 Data Logger configuration file.
SL1 – Commercial name of the Athena data acquisition device.
TPS – Accelerator position sensor.
USB – Communication port with wired communication.
Wifi – Wireless communication technology.
Wintax – Data analysis software (Magneti Marelli).
7
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
1 SL1 KIT
The SL1 kit includes:
SL1 Data Logger
1 GPS Antenna
1 SL1 wiring harness
1 USB flash drive
1 USB data cable (mini - USB) for connection to
the PC
Note: The content of the kit may vary depending on the version.
8
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
2 WHY ACQUIRE...
3 GPS SYSTEM
Data acquisition during test sessions is becoming increasingly important because it permits:
Reducing the vehicle configuration time.
Correcting driving errors.
Controlling vehicle behaviour, statically and dynamically.
Viewing all the acquired parameters.
Controlling engine and chassis performance continuously.
Viewing the lap times of a session once downloaded.
The GPS system (Global Positioning System), on which your GET system is based, uses an algorithm
in order to determine the position of the GPS module that receives the signal transmitted by the
satellites.
By measuring the time a radio signal needs to travel the distance between the satellite and the
receiver and by knowing the precise position of at least 4 satellites, it is possible to identify the 3D
position of the receiver.
24 GPS satellites in orbit, inclined 55 degrees with respect to the equator, are located between
18000 and 20000 km from the earth and rotate around it once every 12 hours.
The satellites transmit a signal between 1.2 and 1.5 GHZ (to prevent errors resulting from
atmospheric refraction) generated by a single oscillator (atomic clock).
The transmitted data contain information about the orbit of the satellites and the time of the
signal, which permit the receiver to define its position on the earth's surface.
The lap times are obtained via GPS: this solution eliminates the need to use
inconvenient beacons on the track and helps provide a time reference during data
analysis.
The GPS uses a stochastic algorithm and is strongly influenced by the quality of the
received signal.
In the case of magnetic or environmental interference, data quality is not
guaranteed.
There must be a minimum number of 5 received satellites to guarantee the quality
of the lap times.
9
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
3.1 FIX GPS
It is necessary to “fix” the satellites to obtain the trajectories and lap times in the acquisitions.
The minimum number of satellites for correct acquisition is 5.
In fixed applications (example Dyno sessions) GPS is not required.
NOTE: The SL1 Data Logger continues to search for satellites during acquisition, which permits
starting acquisition also without GPS data.
In this case, it is probable that the trajectories, which are then displayed by the software, are
compromised.
Evidence of this are quick changes in vehicle position (spikes), also in the order of Km!!!
4 NECESSARY REQUIREMENTS...
The following is required to acquire data:
Analogue signals or digital data (e.g CAN bus) coming from the vehicle
SL1 configured correctly to acquire the desired data
Personal computer
Software LynXLog (required to download data and configure SL1)
Software WinTAX4 (required to analyse the downloaded data)
The SL1 Data Logger can be connected to the vehicle (or the sensors) using the
specific cable (refer to
Annex 3).
SL1 DATA LOGGERVehicle PC
WINTAX
DATA ANALYSIS
SOFTWARE
LYNXLOG
LOGGER
MANAGER
SOFTWARE
SENSOR
SIGNALS
& DATA FROM
CAN BUS
DATA ANALYSIS VIA WINTAX
10
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
5 SL1: INSTALLATION
The SL1 Data Logger is designed to be easily installed in all vehicles.
With the dedicated cables, the Athena Evolution ECU (example RX1PRO) can be directly connected
via CAN bus.
For electrical connections, see
Annex 2 and Annex 3 of this manual.
5.1 INSTALLING THE GPS ANTENNA
Refer to the following instructions to install the GPS antenna properly:
Pay particular attention when moving the GPS antenna: Avoid impacts and check that the
cables are in perfect condition.
Fix the antenna outside the vehicle: obstacles near the antenna could reduce the sensor's
reception ability. An incorrect position could cause an incorrect lap time, incorrect acquisitions
and trajectories.
Do not twist the antenna cable with other cables (especially around high voltage cables): this
could cause inductive interference and therefore problems during operation.
Do not pass the antenna cable around the cable of the spark plug or other electromagnetic
fields. In motorcycles, it is preferable to pass the cable outside the chassis, but always in a
protected area.
Fasten the GPS connector to the antenna input of the SL1 Data Logger without applying
excessive force, do not use tools for tightening.
Some suggestions for fixing the antenna:
Racing motorcycle: fasten the antenna in the rear of the motorcycle, away from heat sources
(exhaust) or in the instrument panel area (above).
Off-road motorcycle: fasten the antenna on the handlebar.
Automobile: fasten the antenna on the roof of the automobile.
Kart: fasten the antenna on the top of the board, if necessary make a support to position the
sensor in the appropriate direction.
11
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
5.2 PRECAUTIONS
6 SL1: FRONT VIEW
Observe the following rules to proceed with the installation of the SL1 Data Logger on the vehicle:
Work in a comfortable environment (example: sufficient work space)
Disconnect the battery
Put all the parts removed from the vehicle in a safe place, making sure not to damage them
Install the system when the engine is cold: during installation, it could come into contact with
hot parts
Carefully handle the connectors and wiring (avoid contact with sharp or hot surfaces)
Keep the washers, nuts and bolts in a safe place during system installation
Install the system so that it does not interfere with moving parts or with the pilot
ATTENTION: INCORRECT INSTALLATION COULD CAUSE PERSONAL
INJURY OR PROPERTY DAMAGE
5: MAIN connector
6: EXP connector
7: USB connector
4: GPS antenna connector
3: DIAGNOSTICS LED - Red
2: GPS LED - Yellow
1: STATUS LED - Green
12
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
7 BEFORE STARTING...
7.1 INSTALLING THE SOFTWARE
(LynXLog + WinTAX Junior version)
The SL1 Data Logger requires LynXLog and WinTAX software.
Follow these instructions:
The SL1 kit includes one Get USB flash drive that contains a file called StartHere, double click
the file and follow the instructions that appear on the screen.
If you want to install the software manually, follow these instructions:
Accept the terms of the license and then press Next>
Proceed as follows to install the LynXLog software:
Double click the software installer icon:
LynXLog_GET_Install_<Version>.exe
LynXLog is available for Microsoft Windows©. The officially supported versions are:
Windows© 7 (32 - 64 bit), Windows© 8 (32 - 64 bit), Windows© 10 (32 - 64 bit).
ATTENTION: Internet Explorer 11 is also required, make sure it is installed.
13
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
Leave all the selected components and press Next>
14
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
Proceed with the installation, following the instructions shown in the following windows:
1- LynXLog
15
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
2- Driver
16
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
3- WinTAX
4- Finish
17
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
7.1.1 HOW TO ACTIVATE THE WINTAX4 JUNIOR LICENSE
WinTAX4 Junior requires a valid user license.
This license must be requested via e-mail to:
The e-mail must contain:
WinTAX Registration ID (shown when WinTAX is executed)
GETW Code (contained in the GETW_code.txt file in the supplied USB flash drive)
In order to always keep the software updated, LynXLog uses an Ota (over the air) update
method
When LynXLog is started, it checks if there are any updates (using the PC internet connection)
If there are updates, LynXLog will download them and will then ask for confirmation to proceed
with the update.
The SL1 kit includes one Get USB flash drive that contains a file called StartHere, double click
the file and follow the instructions that appear on the screen.
7.1.2 SOFTWARE UPDATE
ATTENTION: The update procedure can take some time.
Make sure to start the update when you have time to wait for the process
to be completed.
WinTAX Registration ID
File GETW Code
18
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
If a SL1 Data Logger with outdated firmware that is connected to the PC, LynXLog will ask to
update it
Once the transfer is complete, the software will ask for confirmation to update the SL1 Data
Logger.
If you press Yes SL1 will be updated and when the update process is complete, it will reboot
and will be ready to be used.
If you press No the update will be interrupted and the procedure will restart the next time you
want to update the SL1 Data Logger.
19
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
8 SL1:OPERATING DIAGRAM
First use
Normal use
INSTALLATION
LynXLog & WinTAX4
WinTAX4 JUNIOR
ACTIVATION
ARCHIVE FOLDER
SETTING
(Base Directory)
INSTALLATION OF SL1
DATA LOGGER
IN THE VEHICLE
CONNECT
SL1 DATA LOGGER TO
PC
CONFIGURE THE
ACQUISITION
PARAMETERS
CHANNELS,
TRIGGERS, INFO ETC.
CONNECT SL1 DATA
LOGGER TO THE PC
CONFIGURE THE
ACQUISITION
PARAMETERS
IF NECESSARY
DATA LOGGING DATA DOWNLOAD
WITH
LYNXLOG
DATA ANALYSIS
WITH
WINTAX
20
SL1 DATA LOGGER User Manual Rev. AD
[email protected]www.getdata.it
ENGLISH
9 BEHAVIOUR OF THE LEDs
The SL1 Data Logger LEDs provide information concerning system status.
See the following tables:
AVVIAMENTO
LED TYPE STATUS DESCRIPTION
Green GPS Flashing System control
Yellow SYSTEM ON System control
Red DIAGNOSTICS ON System control
NORMAL CONDITIONS
LED TYPE STATUS DESCRIPTION
Green GPS OFF GPS signal OK
Green GPS Flashing GPS signal search
Yellow SYSTEM ON System ready
Yellow SYSTEM Flashing Acquisition in progress
Red DIAGNOSTICS OFF System OK
Red DIAGNOSTICS Flashing System in alarm
SHUT-OFF
LED TYPE STATUS DESCRIPTION
Green GPS OFF GPS signal OK
Yellow SYSTEM Flashing Acquisition in progress
Red DIAGNOSTICS OFF System OK
SYSTEM UPDATE OTA FUNCTION AND ACQUISITION CONFIGURATION
LED TYPE STATUS DESCRIPTION
Green GPS ON GPS signal OK
Yellow SYSTEM ON Acquisition in progress
Red DIAGNOSTICS Flashing System OK
DROM 5s TO 10s
FROM 20s TO 30s
FROM 3s TO 6s
OTA Update
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92

Athena GET SL1 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers