Ryobi EBS750 Belt Sander User manual
- Category
- Power tools
- Type
- User manual
Contents
1 INSRDUCTION
1.1 Save all warnings and instructions for future
reference.
2 SANDER SAFETY WARNINGS
3 INTENDED USE
4 MAINTENANCE
4.1 GENERAL
4.2 LUBRICATION
4.3 CLEANING THE SANDING BELT
5 ENVIRONMENTAL PROTECTION
6 SYMBOL
7 INSTALLATION INSTRUCTIONS
8 GUARANTEE
9 EC DECLARATION OF CONFORMITY
10 Documents / Resources
10.1 References
11 Related Posts
INSRDUCTION
Important! It is essential that you read the instructions in this manual before operating this machine.
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electri
c shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SANDER SAFETY WARNINGS
Hold power tool by insulated gripping surfaces, because the belt may contact its own cord. Cuttings “live” wire
may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
Always wear safety goggles and a dust mask when sanding, especially sanding overhead.
A suitable breathing respirator must be worn while sanding lead paint, some woods and metal to avoid
breathing the harmful/toxic dust or air.
The machine is not suitable for wet sanding.
Do not use sanding belt larger than needed.
WARNING
Do not throw sanding dust on an open fire because materials in fine particle form may be explosive.
WARNING
If the replacement of the supply cord is necessary, this has to be done by the manufacturer or his agent in order
to avoid a safety hazard.
INTENDED USE
You may use this product for the purposes listed below:
Sanding on wood surfaces.
Removing rust from and sanding steel surfaces
MAINTENANCE
WARNING
The tool should never be connected to a power supply when you are assembling parts, making adjustments, cle
aning, performing maintenance, or when the tool is not in use. Disconnecting the tool will prevent accidental sta
rting that could cause serious injury.
WARNING
When servicing use only identical Ryobi replacement parts. Use of any other parts may create a hazard or caus
e product damage
GENERAL
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial
solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
WARNING
Do not at any time let brake fluids, gasoline, petroleum based products, penetrating oils, etc. come in contact wi
th plastic parts. They contain chemicals that can damage, weaken or destroy plastic.
Electric tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject to accelerated
wear and possible premature failure because the fiberglass chips and grindings are highly abrasive to bearings,
brushes, commutators, etc. Consequently, we do not recommend using this tool for extended work on these types
of materials. However, if you do work with any of these materials, it is extremely important to clean the tool using
compressed air.
WARNING
Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing du
st. If operation is dusty, also wear a dust mask.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit
under normal operating conditions. Therefore, no further lubrication is required.
CLEANING THE SANDING BELT
The sanding belt that came with your sander is made to be re-used. Therefore, it is important that it be cleaned
periodically to remove sanding residue and foreign material that can accumulate over time. One of the ways to
clean sanding belt is to rub the sheets with a hard rubber block. You can also use the clean rubber sole of a shoe.
WARNING
Always remove the sanding belt from sander before cleaning. Failure to do so could cause serious personal inju
ry
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing of as waste. The machine, accessories and packaging
should be sorted for environmental-friendly recycling.
SYMBOL
Safety Alert
Volts
Hertz
After mating current
Watts
No-load speed
Revolutions or reciprocations per minute
CE Conformity
Conformance to technical regulations
Class II tool, double insulation
Please read the instructions carefully before starting the product.
W ear ear protection
Wear eye protection
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
INSTALLATION INSTRUCTIONS
Product specifications
Rating
Voltage
No-load speed
Sanding area size
Sanding belt size
Weight According to EPTAProcedure 01/2003
Measured sound values determined according to EN 60745:
A-weighted sound pressure level
Uncertainty K
A-weighted sound power level
Uncertainty K
Wear ear protectors.
The vibration total values (triaxial vector sum) determined according to EN 60745:
Vibration emission value
Uncertainty K
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardized
test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary
assessment of exposure. The declared vibration emission level represents the main applications of the tool.
However if the tool is used for different applications, with different accessories or poorly maintained, the vibration
emission may differ. This may significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is
switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level
over the total working period. Identify additional safety measures to protect the operator from the effects of
vibration such as: maintain the tool and the accessories, keep the hands warm, organization of work patterns.
GUARANTEE
In addition to any statutory rights resulting from the purchase, this product is covered by a guarantee as stated
below
1. The guarantee period is 24 months for consumers and commences on the date when the product was
purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed
and dedicated to consumer and private use only. So there is no guarantee provided in case of professional or
commercial use.
2. There is, in some cases (i.e. promotion, range of tools), a possibility to extend the warranty period over the
period described above using the registration on the www.ryobitools.eu website. The eligibility of the tool is
clearly displayed in stores and/or on packaging. The end user needs to register his/her newly-acquired tools
online within 8 days from the date of purchase. The end user may register for the extended warranty in his
country of residence if listed on the online registration form where this option is valid. Furthermore, end users
must give their consent to the storage of the data which are required to enter online and they have to accept
the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original
invoice showing the date of purchase will serve
as proof of the extended warranty. Your statutory rights remain unaffected.
3. The guarantee covers all defects of the product during the warranty period due to defaults in workmanship or
material at the purchase date. The guarantee is limited to repair and/or replacement and does not include any
other obligations including but not limited to incidental or consequential damages. The warranty is not valid if
the product has been misused, used contrary to the instruction manual, or being incorrectly connected. This
guarantee does not apply to:
– any damage to the product that is the result of improper maintenance
– any product that has been altered or modified
– any product where original identification (trade mark, serial number) markings have been defaced, altered or
removed
– any damage caused by non-observance of the instruction manual
– any non CE product
– any product which has been attempted to be repaired by an nonqualified professional or without prior
authorization by Techtronic Industries
– any product connected to improper power supply (amps, voltage, frequency)
– any damage caused by external influences (chemical, physical, shocks) or foreign substances
– normal wear and tear of spare parts
– inappropriate use, overloading of the tool
– use of non-approved accessories or parts
– carburettor after 6 months, carburettor adjustments after 6 months
– power tool accessories provided with tool or purchased separately. Such exclusions include but is not limited
to screw driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide
– components (parts and accessories) subject to natural wear and tear, including but not limited to carbon
brushes, chuck, power cord, auxiliary handle, sanding plate, dust bag, dust exhaust tube
4. For servicing, the product must be sent or presented to a RYOBI authorized service station listed for each
country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes
to send the product to the RYOBI service organization. When sending a product to a RYOBI service station, the
product should be safely packed without any dangerous contents such as petrol, marked with sender’s address
and accompanied by a short description of the fault.
5. A repair/replacement under this guarantee is free of charge. It does not constitute an extension or a new start
of the guarantee period. Exchanged parts or tools become our property. In some countries delivery charges or
postage will have to be paid by the sender.
6. This guarantee is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and
Russia. Outside these areas, please contact your authorized RYOBI dealer to determine if another warranty
applies.
AUTHORISED SERVICE CENTRE
To fi nd an authorised service centre near you, visit http://www.ryobitools.eu/service-support/service-agent
EC DECLARATION OF CONFORMITY
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
Herewith we declare that the product
Belt Sander
Brand: Ryobi
Model number: EBS750
Serial number range: 44426501000001-44426501999999
is in conformity with the following European Directives and harmonised standards
2006/42/EC, 2004/108/EC, 2011/65/EU
EN55014-1:2006+A1:2009+A2:2011, EN55014-2:1997+A2:2008
EN61000-3-2:2006+A1:2009+A2:2009, EN61000-3-3:2008,
EN60745-1:2009+A11:2010, EN60745-2-4:2009+A11:2011, EN62233:2008
Andrew John Eyre (BEng, CEng, MIET)
Vice President, Regulatory & Safety
Winnenden, Nov. 5, 2013
Authorised to compile the technical file:
Alexander Krug, Managing Director
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, German
Documents / Resources
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
Ryobi EBS750 Belt Sander User manual
- Category
- Power tools
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ryobi RPS100-S Delta Grinder User manual
-
-
-
Ryobi R18BS-0 User manual
-
-
-
-
-
-