NOYAFA NF-168V User manual

Your excellent helper in measuring instruments.

Your excellent helper in

measuring instruments.

VER: V1

USER MANUALUSER MANUAL

NF-168V

NF-168S

ANTI-INTERFERENCE WIRE TRACKERANTI-INTERFERENCE WIRE TRACKER

ExampleⅠExampleⅡ

Connect launcher and telephone

wire port to be traced in right way

Your excellent helper in measuring instruments. Your excellent helper in measuring instruments.

Trace cable at the other end

with receiver

Connect launcher and LAN cable

port to be traced in right way

Trace cable at the other end

with receiver

Trace cable in

distribution frame

Trace cable in

telephone exc hanger

Find target wire required from numerous

telephone wires and LAN cables

Find target wire required from numerous

telephone wires and LAN cables

Find target wire required from numerous

telephone wires and LAN cables

Find target wire required from numerous

telephone wires and LAN cables

Please read and learn safety instructions

before use or maintain the equipment

•Never expose the equipment directly in the sun.

•Never put the equipment in the place with much dust, humidity and

high temperature (over 40℃)

•Please use battery according to the specification; otherwise, it may

result in damage to equipment.

•Please never dismount the equipment arbitrarily. The maintenance

and care shall be conducted by professional personnel.

•Please take out the battery in launcher and receiver if the equipment

is not used for a long time so as to prevent that the battery liquid

is leaked in future.

•Never use the equipment to detect power cord with electricity (such

as power supply circuit of 220V), other wise, it may result in damage

to equipment and personal injury.

•Never conduct related operation of communication line in

thunderstorm weather so as to prevent lightning stroke and impact

on personal safety.

.............................................................................01

...........................................02

.......................................................................03

..................................................................................08

.....................................................................................09

.......................................................................................10

..............................................................11

................................................................................................03

.................................................................................................03

............................................................................................03

....................................................................................................04

.......................................................................................................05

.....................................................................................................05

....................................................................................................05

................................................................................................05

...........................................................................07

..........................................................................................07

....................................................................................................07

.......................................................................08

.........................................................................................08

...........................................................................08

...............................................................................................08

...................................................................08

Contents

1.Brief Introduction

2.Product interface and keypad functions

3.Operation Instruction

4. Other function

5. Specification

6. Packing list

7. Diagram of series products

(1) Cable tracing

PoE switch

(2)

Fast mode

Slow mode

Manual mode

(3) Visual Fault Detector(VFL)

(1) Emitter Low voltage indicator

(2) Earphone function

(3) Volume adjustable function

(4) Light function

(5) Wire sorting directly with switch

Basic tracing

AC filter tracing

Cable mapping

Continuous mode

Pulse mode

NF-168V

(Details of VFL function, pls refer Page 05)

NF-168S

1. Brief introduction

Emitter Receiver Receiver

Emitter

Your excellent helper in measuring instruments. Your excellent helper in measuring instruments.

NF-168V/NF-168S is an updated item with multifunction of cable tracing,

mapping and Visual fault locator (this function is only for NF-168V) according

to sales requirements. It follows the shells of NF-168 emitter and receiver.

But compared to series products, it’s highlights is three tracing modes, three

Ordinary tracing, mapping mods, and Visual fault locator. Tracing modes---

Anti-interference, PoE switch; Cable mapping--Fast mode Slow mode, ,

fault locator-Continuous mode, Pulse mode.Manual mode; Visual

VERIFY

OFF

TEST

SCAN/VFL

STATUS

PWR/Signal

NF -168 V

NF -168V

Scan/VFL indicator

DIP switch

Wire sorting

indicator

Toggle button

LED indicator

Probe

Signal indicator

LED indicator

Function switch

Sensitivity knob

Earphone

Receiver

Emitter

Spotlight switch

AC filter

Basic

2.Product Interface and Keypad Introduction 3.Operation methods

02 03

Your excellent helper in measuring instruments. Your excellent helper in measuring instruments.

Cable tracing

1)Basic tracing

Emitter

Push the key to SCAN” to enter the basic tracing mode, then blue indication flashes “ ,

which means the emitter works well. Connect one end of network cable/telephone

cable(BNC cable only for NF-168S) to the RJ45/RJ11 (BNC cable only for NF-168S)

port of launcher.

Receiver

Push the key to “Basic” the brightness of indicator and the sound of the speaker is ,

dynamically changed according to the the signal strength. (note that in this mode, even

if there is no signal, the indicator and the speaker will have a weak changed) which ,

means the receiver works well then hold the receiver to find the target line.,

2) AC filter tracing

Emitter:

In the basic mode, short press the “SET” button to enter the AC filter mode, then the

blue indicator flashes, which means the emitter works well.

Connect one end of network cable/telephone cable (BNC cable only for NF-168S) to

the RJ45/RJ11(BNC cable only for NF-168S)port of launcher.

Receiver:

Push the key to “AC Filter”, the brightness of indicator and the sound of the speaker is

dynamically changed according to the signal strength, which means the receiver works

well, then hold the receiver to find the target line.

04 05

When the battery of the emitter is low, the red light below will flash ,

otherwise it will not light. When the battery of the receiver is low, the

red light above flashes, otherwise it is always on; the user can adjust

the sensitivity on the right to achieve the best scanning effect

according to the usage scenario.

NOTICE

Power on Short press

SET

Short press

SET

Short press SET

Your excellent helper in measuring instruments. Your excellent helper in measuring instruments.

Basic

tracing

AC filter

tracing PoE switch

Cable tracing mode switching graphic

3)PoE switch

Emitter:

In AC filter mode, short press “SET” key to enter POE scan mode, then the indicator

flashes red and blue, which means the emitter works well.

Connect one end of network cable to the RJ45 port of launcher.

Receiver:

Push the key to “AC Filter” to enter PoE switch mode, the brightness of indicator and

the sound of the speaker is dynamically changed according to the signal strength, which

means the receiver works well, then hold the receiver to find the target line.

2. Tracing mapping ( RJ45 as an example)

1. Connect two ends of network calbe to the RJ45 port of launcher and receiver separately.

2. And push the key to “test”, the wire sort indicators will flash, which means the

transmitter works well.

3. If the wire is normal, and the GND is not connected, then the 8 indicators will flash

one by one. And if GND is connected, then the 1 to 8 and G indicators will flash one

by one.

4. If there is miswires as below. If line“2” is open, then the 2 indicator of emitter and

receiver will not flash. If there is several lines are open, the corresponding indicators

will not flash. And if less than 2 lines are connected, none of the lights is on.

When the line are cross, for example, line“2” and line“3” disorder, the indicators

flash as follows,

Transmitter : 1-2-3-4-5-6-7-8-G

Receiver: 1-3-2-4-5-6-7-8-G

When there is short circuit of line“2” and “3”, the 2 and 3 indicators of receiver will

not flash while the other lights still do.

The wire tracker has three mapping modes as below:

1) Fast mode(0.5 second)

Emitter: Push the key to “test” to enter Fast mode, the wire sort indicator flashes, then

the LED indicator will flash by one bye one per 0.5 second.

2) Slow mode(1 second)

second

Emitter: In the fast mode, short press the “SET” button to enter the slow mode, the wire

sort indicator flashes, then the LED indicator will flash by one bye one per 1 .

NOTICE

When the battery of emitter is low, the red light above will flash,

otherwise it will not light. When mapping,Only connect the cable

to be tested to the Rj45 port of emitter and receiver, at this time the

LED light status will show the cable continuity.

06 07

Power

on Fast mode Slow mode Manual

mode

Short press

SET

Short press

SET

Long press

SET

Mapping mode switching graphic

Long press SET

Short press

SET

Long press SET

3. Visual fault loactor (this function is only for NF-168V)

NOTICE

When they battery of emitter is low,the indicator below will flash,

otherwise it will not light.

Long press

SET Short press SET

Short press SET

Long press SET

Tracing

mode

Continuous

mode

Pulse

mode

VFL mode

VFL mode switching graphic

Your excellent helper in measuring instruments. Your excellent helper in measuring instruments.

3) Manual mode

Emitter: In fast/slow mode, long press “SET” button to enter manual mode, user need

to short press “SET” button, the wire sort indicator flashes, then the LED indicator will

flash stage by stage.

This function can inspect fiber failure when they connect with optical interface. It’s

light has two mode as below.

1)Continuous mode

In any cable tracing mode, long press the “SET” button enter the continuous mode, this

mode is defaulted. You will see the red laser emitting from the optical interface. At this

time, the upper red light also will flash. (Please don't stare at the beam, for fear of

damaging your eyes).

2)Pulse mode

In the continuous mode, short press the “SET” button enter the pulse mode, the LED

synchronize with light-emitting (pulse frequency will be controlled at 1-2 Hz). At this

time the upper red light also will flash.

08 09

4. Other functions

3) Sensitivity adjustment function

Turn the sensitivity adjustment knob on the receiver when tracing cable to

adjust the value to be the appropriate degree.

(1) Low-voltage hint function

When the battery is low (≤6V), push the function button to “scan” or “test” ,

at this time, both the scan indicator and wire sorting indicator will flash, which

means the battery should be replaced.

(2) Earphone function

The earphone can be worn in noisy environment for operation so as to avoid

external interference.

(4) Floodlight function

The side floodlight can be started at night or in dark. The floodlight turns

on so as to facilitate your normal operation.

(5) Wire sorting directly with switch

Connect the line to be tested with transmitter and switch,then get the result

from flashlights.

Your excellent helper in measuring instruments. Your excellent helper in measuring instruments.

5. Specification

Emitter

Tracing

VFL

(NF-168V)

Compatible cable

Max. signal voltage

Max valume

Tone frequency

Tone mode

Ordinary tracing

Anti-interference

Distance of transmission

Wave length

Power

Mode

Mapping

Battery Type

Battery low indicate

Voltage protection

Max. working current

Dimension(LxWxD)

Anti interference reception

Sensitivity adjust

Ordinary Huting

Earjack

LED lighting

Battery Type

Power indicate

Battery low indicate

Max. working current

Dimension(LxWxD)

RJ45, RJ11, BNC cable

8±1.0Vp-p

105dB

455Hz

1 Tone

YES

RJ45 300M non-load/load

650nm

5mW

Constant ight mode, Blinking mode

Fast, slow, manual

DC9.0V(6F22 DC9V x 1pcs)

6.0V±0.5V

DC 60V

Less than 100mA

146*57*30mm

YES

DC9.0V(6F22 DC9V x 1pcs)

LED Power indicator

6.0V±0.5V

≤150mA

187*46*27mm

Receiver

YES

10 11

Your excellent helper in measuring instruments. Your excellent helper in measuring instruments.

Emitter 1PC

Receiver 1PC

Testing line 1PC

Earphone 1PC

User manual 1PC

Battery 2PCS

Kit 1PC

Color box 1PC

6. Packing list 7.Diagram of series products

NF-8601S NF-300 NF-8209

NF-816L NF-268 NF-820

NF-826 NF-488 NF-272L

NF-515 NF-5120 NF-521

NOYAFA NF-168V, NF-168S User manual

Related papers

Other documents