Hikoki H 45SB2 User manual

English

1

H 45SB2

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE

AVERTISSEMENT

Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de

ce produit. Prière de lire et de comprendre ce mode d’emploi avant d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs avant

qu’ils utilisent l’outil motorisé.

INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS

WARNING

Improper and unsafe use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read

and understand this manual before operating the power tool. Please keep this

manual available for others before they use the power tool.

MANUAL DE INSTRUCCIONES E INSTRUCCIONES DE SEGURIDAD

ADVERTENCIA

¡La utilización inapropiada e insegura de esta herramienta eléctrica puede resultar

en lesiones serias o en la muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y comprenda este manual antes de utilizar la herramienta eléctrica. Guarde

este manual para que puedan leerlo otras personas antes de que utilicen la

herramienta eléctrica.

MODEL DEMOLITION HAMMER

MODELE MARTEAU PIQUEUR

MODELO MARTILLO DEMOLEDOR

English

2

CONTENTS

English

Page

IMPORTANT INFORMATION ............. 3

MEANINGS OF SIGNAL WORDS ...... 3

SAFETY

IMPORTANT SAFETY INSTRUCTIONS

FOR USING ALL POWER TOOLS ..................

4

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE DEMOLITION HAMMER...

8

REPLACEMENT PARTS ...................... 8

POLARIZED PLUGS ............................ 8

USE OF EXTENSION CORD ............... 9

DOUBLE INSULATION FOR SAFER OPERATION

... 10

Page

OPERATION AND MAINTENANCE

NAME OF PARTS.............................. 11

SPECIFICATIONS .............................. 11

ACCESSORIES .................................. 12

STANDARD ACCESSORIES ......... 12

OPTIONAL ACCESSORIES ........... 12

APPLICATIONS ................................. 13

PRIOR TO OPERATION..................... 13

HOW TO USE THE DEMOLITION HAMMER

..... 15

HOW TO REPLACE GREASE............ 15

MAINTENANCE AND INSPECTION

.... 16

SERVICE AND REPAIRS ................... 17

PARTS LIST ....................................... 48

TABLE DES MATIERES

Français

Page

INFORMATIONS IMPORTANTES .... 18

SIGNIFICATION DES MOTS D’AVERTISSEMENT

.. 18

SECURITE

CONSIGNES DE SECURITE IMPORTANTES POUR

L’UTILISATION DE TOUS LES OUTILS ELECTRIQUES

...

19

CONSIGNES DE SECURITE IMPORTANTES

POUR L’UTILISATION DU MARTEAU PIQUEUR

..

23

PIECES DE RECHANGE .................... 23

FICHE POLARISEES .......................... 23

CORDON DE RALLONGE ................. 24

DOUBLE ISOLATION POUR UN

FONCTIONNEMENT PLUS SUR

........ 25

Page

UTILISATION ET ENTRETIEN

NOM DES PIECES............................. 26

FICHE TECHNIQUE ........................... 26

ACCESSOIRES .................................. 27

ACCESSOIRES STANDARD ......... 27

ACCESSOIRES EN OPTION.......... 27

APPLICATIONS ................................. 28

AVANT L’UTILISATION .................... 28

UTILISATION DU MARTEAU PIQUEUR

.... 30

REMPLACEMENT DE LA GRAISSE

....... 30

ENTRETIEN ET INSPECTION ........... 31

SERVICE APRES-VENTE ET REPARATIONS

..... 32

LISTE DES PIECES ............................ 48

ÍNDICE

Español

Página

INFORMACIÓN IMPORTANTE......... 33

SIGNIFICADO DE LAS PALABRAS DE SEÑALIZACIÓN

.. 33

SEGURIDAD

INSTRUCCIONES IMPORTANTES DE SEGURIDAD PARA

UTILIZACIÓN DE TODAS LAS HERRAMIENTAS ELÉCTRICAS

.. 34

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA UTILIZACIÓN DEL MARTILLO DEMOLEDOR

.. 38

PIEZAS DE REEMPLAZO .................. 38

ENCHUFES POLARIZADOS ............. 38

UTILIZACIÓN DE UN CABLE PROLONGADOR

...... 39

AISLAMIENTO DOBLE PARA OFRECER UNA

OPERACIÓN MÁS SEGURA.........................

40

Página

OPERACIÓN Y MANTENIMIENTO

NOMENCLATURA ............................ 41

ESPECIFICACIONES ......................... 41

ACCESORIOS .................................... 42

ACCESORIOS ESTÁNDAR............ 42

ACCESORIOS OPCIONALES ........ 42

APLICACIONES ................................. 43

ANTES DE LA OPERACIÓN.............. 43

FORMA DE UTILIZAR EL MARTILLO DEMOLEDOR

.. 45

FORMA DE REEMPLAZAR LA GRASA

.. 45

MANTENIMIENTO E INSPECCIÓN.. 46

SERVICIO Y REPARACIÓN ............... 47

LISTA DE PIEZAS.............................. 48

English

3

IMPORTANT INFORMATION

Read and understand all of the operating instructions, safety precautions and warn-

ings in the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused

by the failure to observe basic safety rules or precautions. An accident can often be

avoided by recognizing a potentially hazardous situation before it occurs, and by

observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction

Manual and in the sections which contain the operation and maintenance instruc-

tions.

Hazards that must be avoided to prevent bodily injury or machine damage are iden-

tified by WARNINGS on the power tool and in this Instruction Manual.

Never use this power tool in a manner that has not been specifically recommended

by HITACHI, unless you first confirm that the planned use will be safe for you and

others.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could re-

sult in serious personal injury.

CAUTION indicates a hazardous situations which, if ignored, could result in moder-

ate personal injury, or could cause machine damage.

NOTE emphasizes essential information.

English

4

SAFETY

INPORTANT SAFETY INSTRUCTIONS

FOR USING ALL POWER TOOLS

WARNING: Death or serious bodily injury could result from improper or un-

safe use of power tools. To avoid these risks, follow these basic

safety instructions:

READ ALL INSTRUCTIONS

1. NEVER TOUCH MOVING PARTS.

Never place your hands, fingers or other body parts near the tool’s moving parts.

2. NEVER OPERATE WITHOUT ALL GUARDS IN PLACE.

Never operate this tool without all guards or safety features in place and in proper

working order. If maintenance or servicing requires the removal of a guard or

safety feature, be sure to replace the guard or safety feature before resuming

operation of the tool.

3. ALWAYS WEAR EYE AND EAR PROTECTOR.

Protect yourself from flying or expelled wood chips, metal particles or other de-

bris by using protective goggles or equivalent eye protector. Wear ear protector

to protect yourself from excessive noise.

4. PROTECT YOURSELF AGAINST ELECTRIC SHOCK.

Prevent body contact with grounded surfaces such as pipes, radiators, ranges

and refrigeration enclosures. Never operate the tool in damp or wet locations.

5. DISCONNECT TOOLS.

Never leave the tool connected to a power source. Always disconnect the tool

from its power source before servicing, inspecting, maintaining, cleaning and

before changing or checking any parts.

6. AVOID UNINTENTIONAL STARTING.

Don’t carry the tool while it is connected to its power source. Don’t carry the tool

with your finger near the power switch. Be sure the power switch is in the ‘“off”

position before connecting the tool to its power source.

7. STORE TOOL PROPERLY.

When not in use, the tool should be stored in a dry place. Keep out of reach of

children. Lock-out the storage area.

8. KEEP WORK AREA CLEAN.

Cluttered areas and benches invite injuries. Clear all work areas and work benches

of unnecessary tools, debris, furniture, etec.

English

5

9. CONSIDER WORK AREA ENVIRONMENT.

Don’t expose power tools to rain. Don’t use power tools in damp or wet loca-

tions. Keep work area well lit and well ventilated.

Don’t use tool in presence of flammable liquids or gases.

Power tools produce sparks during operation. They also spark when switch-

ing ON/OFF. Never use power tools in sites containing lacquer, paint, ben-

zine, thinner, gasoline, gases, adhesive agents, and other materials which

are combustible or explosive.

10. KEEP CHILDREN AWAY.

Do not let visitors contact tool or extension cord.

All visitors should be kept safely away from work area.

11. DON’T FORCE TOOL.

It will do the job better and safer at the rate for which it was intended.

12. USE RIGHT TOOL.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended—for example—don’t use circular saw

for cutting tree limbs or logs.

13. DRESS PROPERLY.

Do not wear loose clothing or jewelry. They can be caught in moving parts.

Rubber gloves and non-skid footwear are recommended when working out-

doors.

Wear protective hair covering to contain long hair.

14. USE FACE, DUST MASK OR RESPIRATOR IF OPERATION IS DUSTY.

All persons in the area where power tools are being operated should also wear

face, dust mask or respirator.

15. DON’T ABUSE CORD.

Never carry tool by cord or yank it to disconnect from receptacle.

Keep cord from heat, oil and sharp edges.

16. SECURE WORK.

Use clamps or a vise to hold work. It’s safer than using your hand and it frees

both hands to operate tool.

17. DON’T OVERREACH.

Keep proper footing and balance at all times.

18. MAINTAIN TOOLS WITH CARE.

Keep tools sharp and clean for better and safer performance.

Follow instructions for lubricating and changing accessories.

Inspect tool cords periodically and if damaged, have repaired by an authorized

service center. Inspect extension cords periodically and replace if damaged.

Keep handles dry, clean, and free from oil and grease.

English

6

19. REMOVE ADJUSTING KEYS AND WRENCHES.

Keys and adjusting wrenches remove from tool before turning it on.

20. OUTDOOR USE EXTENSION CORD.

When tool is used outdoors, use only extension cord intended for use outdoors

and so marked.

21. STAY ALERT.

Watch what you are doing. Use common sense. Do not operate tool when you

are tired.

Tools should never be used by you if you are under the influence of alcohol,

drugs or medication that makes you drowsy.

22. CHECK DAMAGED PARTS.

Before further use of the tool, a guard or other part that is damaged should be

carefully checked to determine that it will operate properly and perform its

intended function. Check for alignment of moving parts, binding of moving

parts, breakage of parts, mounting, and any other conditions that may affect its

operation.

A guard or other part that is damaged should be properly repaired or replaced

by an authorized service center unless otherwise indicated elsewhere in this

Instruction Manual.

Have defective switches replaced by the authorized service center.

Do not use tool if switch does not turn it on and off.

23. NEVER USE A POWER TOOL FOR APPLICATIONS OTHER THAN THOSE SPECI-

FIED.

Never use a power tool for applications other than those specified in the In-

struction Manual.

24. HANDLE TOOL CORRECTLY.

Operate the tool according to the instructions provided herein. Do not drop or

throw the tool. Never allow the tool to be operated by children, individuals

unfamiliar with its operation or unauthorized personnel.

25. CHECK FOR LIVE WIRES.

Avoid the risk of severe electrical shock by checking for live electrical wires that

may be buried in walls, floors or ceilings. The wires should be de-energized

before work begins.

26. KEEP ALL SCREWS, BOLTS AND COVERS TIGHTLY IN PLACE.

Keep all screws, bolts, and plates tightly mounted. Check their condition peri-

odically.

27. DO NOT USE POWER TOOLS IF THE PLASTIC HOUSING OR HANDLE ARE

CRACKED.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools

should not be used until repaired.

English

7

28. BLADES AND ACCESSORIES MUST BE SECURELY MOUNTED TO THE TOOL.

Prevent potential injuries to yourself or others. Blades, cutting implements and

accessories which have been mounted to the tool should be secure and tight.

29. KEEP MOTOR AIR VENT CLEAN.

The tool’s motor air vent must be kept clean so that air can freely flow at all

times. Check for dust build-up frequently.

30. OPERATE POWER TOOLS AT THE RATED VOLTAGE.

Operate the power tool at voltages specified on their nameplates.

If using the power tool at a higher voltage than the rated voltage, it will result in

abnormally fast motor revolution and may damage the unit and burn out the

motor.

31. NEVER USE A TOOL WHICH IS DEFECTIVE OR OPERATING ABNORMALLY

If the tool appears to be operating unusually, making abnormal noises, or oth-

erwise appears defective, stop using it immediately and arrange for repairs by

a Hitachi authorized service center.

32. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF.

Don’t leave tool until it comes to a complete stop.

33. CAREFULLY HANDLE POWER TOOLS.

Should a power tool be dropped or struck against hard materials inadvertently

it may be deformed, cracked, or damaged.

34. DO NOT WIPE PLASTIC PARTS WITH SOLVENT.

Solvents such as gasoline, thinner, benzine, carbon tetrachloride, and alcohol

may damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

35. USE ONLY GENUINE HITACHI REPLACEMENT PARTS.

Replacement parts not manufactured by Hitachi may void your warranty and

can lead to malfunction and resulting injuries. Genuine Hitachi parts are avail-

able from your dealer.

English

8

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE DEMOLITION HAMMER

WARNING: Death or serious bodily injury could result from improper or un-

safe use of the demolition hammer. To avoid these risks, follow

these basic safety instructions:

1. NEVER touch the tool bit with bare hands after operation.

2. NEVER wear gloves made of stuff liable to roll up such as cotton, wool, cloth

or string, etc.

3. ALWAYS attach the side handle and securely grip the Demolition Hammer.

4. ALWAYS wear eye and ear protectors during operation.

5. ALWAYS be careful with buried object such as an underground wiring.

Touching these active wiring or electric cable with this tool, you may receive

an electric shock.

Comfirm if there are any buried object such as electric cable within the wall,

floor or ceiling where you are going to operate here after.

REPLACEMENT PARTS

When servicing use only identical replacement parts.

Repairs should be conducted only by a Hitachi authorized service center.

POLARIZED PLUGS

To reduce the risk of electrick shock, this equipment has a polarized plug (one blade

is wider than the other).

This plug will fit in a polarized outlet only one way.

If the plug does not fit fully in the outlet, reverse the plug.

If it still does not fit, contact a qualified electrician to install the proper outlet.

Do not change the plug in any way.

English

9

USE OF EXTENSION CORD

Make sure your extension cord is in good condition. When using an extension cord,

be sure to use one heavy enough to carry the current your product will draw.

An undersized cord will cause a drop in line voltage resulting in loss of power and

overheating. Table shows the correct size to use depending on cord length and

nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the

gage number, the heavier the cord.

MINIMUM GAGE FOR CORD SETS

Total Length of Cord in Feet (Meter)

0 – 25 26 – 50 51 – 100 101 – 150

(0 – 7.6) (7.9 – 15.2) (15.5 – 30.5) (30.8 – 45.7)

Ampere Rating AWG

More Not More

Than Than

0 – 618161614

6 – 10 18 16 14 12

10 – 12 16 16 14 12

12 – 16 14 12 Not Recommended

WARNING: Avoid electrical shock hazard. Never use this tool with a dam-

aged or frayed electrical cord or extension cord.

Inspect all electrical cords regularly. Never use in or near water

or in any environment where electric shock is possible.

English

10

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insula-

tion design. “Double insulation” means that two physically separated insulation

systems have been used to insulate the electrically conductive materials connected

to the power supply from the outer frame handled by the operator. Therefore, either

the symbol “ ” or the words and “Double insulation” appear on the power tool or

on the nameplate.

Although this system has no external grounding, you must still follow the normal

electrical safety precautions given in this Instruction Manual, including not using

the power tool in wet environments.

To keep the double insulation system effective, follow these precautions:

䡬 Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble

this power tool, and only genuine HITACHI replacement parts should be in-

stalled.

䡬 Clean the exterior of the power tool only with a soft cloth moistened with soapy

water, and dry thoroughly.

Never use solvents, gasoline or thinners on plastic components; otherwise the

plastic may dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS OF THIS TOOL!

English

11

OPERATION AND MAINTENANCE

NOTE:

The information contained in this Instruction Manual is designed to assist you in

the safe operation and maintenance of the power tool.

Some illustrations in this Instruction Manual may show details or attachments

that differ from those on your own power tool.

NAME OF PARTS

Nameplate

Switch Trigger

Bruch Cap

(Under the Tail Cover)

Tool Holder

Front Cover

Housing

Side Handle

Fig. 1

SPECIFICATIONS

Motor Single-Phase, Series Commutator Motor

Power Source Single-Phase, 115V AC 60Hz

Current 8A

Full-load Impact Rate 3,000/min.

Weight 10.6 lbs (4.8 kg)

English

12

ACCESSORIES

WARNING: Accessories for this power tool are mentioned in this Instruction

Manual.

The use of any other attachment or accessory can be dangerous

and could cause injury or mechanical damage.

STANDARD ACCESSORIES

(1)Case (Code No. 310131) ...........................................................................................1

(2)Side Handle (Code No. 981870)...............................................................................1

(3)Allen Wrench (for 6mm screw) (Code No. 944459) ...............................................1

(4)Allen Wrench (for 5mm screw) (Code No. 944458) ...............................................1

OPTIONAL ACCESSORIES................... sold separately

䡬 Cruching

+

(1) Bull point

Overall length Code No.

12" (300 mm) 985383

䡬 Groove digging and edging

+

(1) Cold chisel

Overall length Code No.

12" (300 mm) 985381

18" (460 mm) 985382

English

13

䡬 Asphalt cutting

+

(1) Cutter

Overall length Width Code No.

1-1/2" (38 mm) 985384

2" (50 mm) 985385

䡬 Hammer grease A

30g (in a tube) (Code No. 981840)

70g( in a tube) (Code No. 308471)

NOTE:

Accessories are subject to change without any obligation on the part of the HITACHI.

APPLICATIONS

䡬 Breaking concrete, chipping off concrete, grooving, bar cutting, and driving piles.

(Application examples)

Installation of piping and wiring, sanitary facility installation, machinery installa-

tion, water supply and drainage work, interior jobs, harbor facilities and other

civil engineering work.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power source re-

quirements specified on the product nameplate.

12"

(300 mm)

䡬 Scooping work

+

(1) Scoop (Code No. 985386)

English

14

2. Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a recep-

tacle while the switch is in the ON position, the power tool will start operating

immediately and can cause serious injury.

3. Extension cord

When the work area is far away from the power source, use an extension cord of

sufficient thickness and rated capacity (refer to page 8). The extension cord should

be kept as short as practicable.

WARNING: Damaged cord must be replaced or repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired.

Consult an authorized electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause overheating, resulting in firing.

5. Confirming condition of the environment:

Confirm that the work site is placed under appropriate conditions conforming to

prescribed precautions.

6. How to install tool

NOTE: For tools such as a bull point

and a cold chisel, use only

Hitachi genuine parts.

(1)Clean, then smear the tool shank with

the grease (optional accessory).

(2)Pull the tool holder in the direction of

arrow 1 and rotate it in the direction

of arrow 2 (counterclockwise). Fully

insert the tool shank into the hexago-

nal hole of the front cover. (Fig. 2)

(3)Return the tool holder to fix the tool.

NOTE: Remove in the reverse order

for installation.

Fig. 2

1

2

䊳

Tool Shank

Front Cover

Tool Holder

English

15

HOW TO USE THE DEMOLITION HAMMER

1. After placing the tip of the tool in the

base hole, switch ON.

2. By utilizing the empty weight of the

machine and firmly hold the hammer

with both hands, you can effectively

control the subsequent recoil motion.

Proceed at a moderate work-rate, ap-

plying too much force will impair effi-

ciency.

CAUTION: After long time of use, the front cover becomes hot.

Therefore, be careful not to burn your hands.

HOW TO REPLACE GREASE

This hammer is full air-tight construction to protect against dust and to prevent

lubricant leakage. Therefore, the hammer can be used without replenishing grease

for long periods. Replace the grease as described below.

1. Grease replacement period

After purchase, replace grease after every 6 months of usage. Ask for grease

replacement at the nearest authorized HITACHI Service Center. Proceed for re-

placement of grease.

2. Grease replacement

CAUTION:

䡬 Before replacing the grease, turn the power off and pull out the power plug.

(1)Remove the crank cover and thor-

oughly remove the old grease inside.

(2)Apply 0.7 oz (20g) of HITACHI Hammer

Grease A (optional accessory, con-

tained in tube) into the crank case.

(3)After replacing the grease, mount the

crank cover securely.

NOTE:

䡬 The Hitachi Hammer Grease A is of the

low viscosity type. When the supplied

grease tube is consumed, purchase

from an Authorized Hitachi Service

Agent.

䡬 Do not excessively supply the desig-

nated amount of grease. Otherwise,

the tool should not operate accurately.

Fig. 3

Crank Cover

Fig. 4

English

16

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug during

maintenance and inspection.

1. Inspecting the tool

Since use of a dull tool will degrade efficiency and cause possible motor mal-

function, sharpen or replace the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that they are properly tight-

ened. Should any of the screws be loose, retighten them immediately.

WARNING: Using this demolition hammer with loosened screws is extremely

dangerous.

3. Inspecting the carbon brushes

(Fig. 5)

The motor employs carbon brushes

which are consumable parts. When

they become worn to or near “wear

limit”, it could result in motor trouble.

When an auto-stop carbon brush is

equipped, the motor will stop auto-

matically. At that time, replace both

carbon brushes with new ones which

have the same carbon brush Nos.

shown in the figure. In addition, always

keep carbon brushes clean and ensure

that they slide freely within the brush

holders.

NOTE: Use HITACHI carbon bruch No. 73 indicated in Fig. 5.

4. Replacing carbon brushes (Refer to figure for name of parts)

Loosen the set screw then remove the tail cover. By loosening the brush cap, the

carbon brushes can be removed. After fitting new carbon brushes, properly re-

tighten the brush cap and mount the tail cover.

0.67" (17 mm)

0.24" (6 mm)

Wear Limit

No. of Carbon

Brush

73

䊳

Fig. 5

English

17

SERVICE AND REPAIRS

All quality power tools will eventually require servicing or replacement of parts

because of wear from normal use. To assure that only genuine replacement parts

will be used, all service and repairs must be performed by a HITACHI AUTHORIZED

SERVICE CENTER, ONLY.

NOTE:

Specifications are subject to change without any obligation on the part of the

HITACHI.

Page is loading ...

49

Español

47 Roll Pin D6✕22

48 Handle Holder (A)

49 Handle Bolt

50 Fan

51 Armature Ass’y

52 Fan Guide

53 Hex. Hd. Tapping Screw D5✕50

54 Stator

55 Brush Terminal

56 Washer (A)

57 Ball Bearing (608VVMC2EPS2L)

58 Housing Ass’y

59

Hex. Socket Hd. Bolt (W/Flange)

M5✕45

60 Brush Cap

61A Carbon Brush

62 Brush Holder

63 Hex. Socket Set Screw M5✕8

64 Bearing Bushing (B)

65A Tail Cover

66 Tapping Screw (W/Flange) D4✕16

67 Internal Wire Holder

68 Handle Packing (B)

69 Tapping Screw (W/Washer) D5✕20

70

Seal Lock Hex. Socket Hd. Bolt

M5✕12

71 Distance Piece (B)

72 Handle (B)

73 Pillar Terminal

74 Switch (A)

75 Handle (A)

76 Tapping Screw (W/Flange) D4✕25

77 Cord Armor

78 Terminal M4.0

79 Tapping Screw (W/Flange) D4✕16

80 Cord Clip

81 Cord

501 Hex. Bar Wrench 4MM

502 Hex. Bar Wrench 5MM

503 Case

Parts are subject to change without any

obligation on the part of the HITACHI due to

improvements.

1 Stop Washer

2 Stopper Sprintg

3 Knob (A)

4 Needle Roller D4✕20

5 Nylock High Tension Bolt M7✕25

6 Front Cover

7 Stop Lever

8 Second Hammer

9 Damper Washer

10 Damper

11 Washer

12 Cylinder Case Ass’y

13 O-Ring

14 Nylock Bolt (W/Flange) M6✕25

15 Cylinder

16 O-Ring (S-48)

17 Striker

18 O-Ring

19 Piston Pin

20 Piston

21 Retaining Ring For D10 Shaft

22 Connecting Rod

23

Seal Lock Hex. Socket Hd. Bolt

M4✕12

24 Crank Cover

25 O-Ring (S-55)

26 Crank Shaft

27 Feather Key 4✕4✕10

28 Retaining Ring For D40 Hole

29 O-Ring (S-40)

30 Ball Bearimg (6203VVCMPS2S)

31 Oil Seal

32 Nameplate

33 Crank Case

34 Handle Damper

35 Transatory Unit

36 Handle Packing (A)

37 First Gear

38 HITACHI Label

39 Needle Bearing (M661)

40 Gear Cover Ass’y

41 Ball Bearing (6201VVCMPS2S)

42 Washer (B)

43 Side Handle

44 Spring

45 Handle Holder Ass’y

46 Handle Holder (B)

Part NamePart Name

Item

No.

Item

No.

Page is loading ...

101

Code No. C99072463 N

Printed in Japan

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construc-

tion activities contains chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm. Some examples of these chemicals are:

● Lead from lead-based paints,

● Crystalline silica from bricks and cement and other masonry products, and

● Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type

of work. To reduce your exposure to these chemicals: work in a well ventilated area,

and work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

AVERTISSEMENT:

La poussière résultant d'un ponçage, d'un sciage, d'un meulage, d'un perçage ou

de toute autre activité de construction renferme des produits chimiques qui sont

connus par l'Etat de Californie pour causer des cancers, des défauts de naissance

et autres anomalies de reproduction. Nous énumérons ci-dessus certains de ces

produits chimiques:

● Plomb des peintres à base de plomb,

● Silice cristalline des briques et du ciment et autres matériaux de maçonnerie, et

● Arsenic et chrome du bois d'oeuvre traité chimiquement.

Le risque d'exposition à ces substances varie en fonction de la fréquence d'exécution

de ce genre de travail. Pour réduire l'exposition à ces produits chimiques, travailler

dans un lieu bien ventilé, et porter un équipement de protection agréé, par exemple

un masque anti-poussière spécialement conçu pour filter les particules microscopiques.

ADVERTENCIA:

Alogunos polvos creados por el lijado mecámico, el aserrado, el esmerilado, el

taladrado y otras actividades de construcción contienen sustancias químicas conocidas

por le Estado de California como agentes cancerígenos, defectos congénitos y otros

daños reproductores. Algunos ejemplos de estas sustancias químicas son:

● El plomo de las pinturas a base de plomo,

● El sílice cristalino de los ladrillos y cemento y otros productos de mampostería, y

● El arsénico y el cromo de la madera tratada químicamente.

El riesgo resultante de la exposición varía según la frecuencia con que se realiza

este tipo de trabajo. Para reducir la exposicíon a esta sustancias químicas: trabaje

en un lugar bien ventilado y realice el trabajo utilizando el equipamiento apropiado,

tal como las máscares para el polvo especialmente diseñados para eliminar las

partículas minúsculas.

Issued by

Sinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo 108-6020, Japan

Distributed by

3950 Steve Reynolds Blvd.

Norcross, GA 30093

itachi Koki Canada Co.

6395 Kestrel Road

Mississauga ON L5T 1Z5

Hikoki H 45SB2 User manual

This manual is also suitable for

Hikoki H 45SB2 User manual

in other languages

Related papers

Other documents