Rust-Oleum 239083 User manual

239083
Rust-Oleum
Brand
Rust-Oleum
Model
239083
Type
User manual
TECHNICAL DATA SRT-02
STOPS RUST
ENAMEL BRUSH
Form: CS2155
Rev.: 022613
1
.DESCRIPTION AND USES .
Rust-Oleum
®
Stops Rust
®
Oil-based Enamels provides excellent
rust prevention when applied directly to metal. They also offer
excellent coverage, chip resistance and color retention. For even
longer, lasting protection, use a Stops Rust
®
Primer first. Not for
use of galvanized steel.
.PRODUCTS .
Quarts ½Pints Description
7715502 ---- Metallic Aluminum
7723502 ---- Navy
7724502 ---- Sail Blue
7727502 7727730 Royal Blue
7733502 ---- Dark Hunter Green
7738502 7738730 Hunter Green
7747502 7747730 Sunburst Yellow
7754502 ---- Anodized Bronze
7762502 7762730 Sunrise Red
7763502 ---- Carnival Red
7765502 7765730 Regal Red
7768502 ---- Burgundy
7770502 ---- Almond
7771502 ---- Sand
7775502 7775730 Leather Brown
7776502 7776730 Flat Black
---- 7777730 Satin Black
7779504 7779730 Gloss Black
7784502 ---- Charcoal Gray
7786502 7786730 Smoke Gray
7789502 ---- Canvas White
7790502 7790730 Flat White
---- 7791730 Satin White
7792504 7792730 Gloss White
7794504 ---- Antique White
7797502 ---- Semi-Gloss White
7798502 ---- Semi-Gloss Black
239083 239084 Flat Brown
..PRODUCT APPLICATION .
PAINTING CONDITIONS
Apply only when air and surface temperatures are
between 50-90°F (10-32°C) and humidity is below
85% to ensure proper drying. Do not apply to
surfaces that will exceed 200°F (93°C). Do not use
on galvanized steel.
..PRODUCT APPLICATION .
SURFACE PREPARATION
ALL SURFACES: Remove all dirt, grease, oil, salt and
chemical contaminants by washing the surface with a
commercial detergent or other suitable cleaning method.
Rinse thoroughly with fresh water and allow to fully dry. All
surfaces must be dry at time of application.
STEEL: Scrape and wire brush or power tool clean to
remove loose rust, scale and deteriorated previous
coatings. Use 7769 Rusty Metal Primer for sound rusted
or clean metal before application of a finish coat. 7780
White Clean Primer is best for clean metal but may be
used on sound rusted metal as well.
PREVIOUSLY COATED: Previously coated surfaces must
be sound and in good condition. Smooth, hard, or glossy
finishes should be scarified by sanding to create a surface
profile. The Stops Rust
®
Enamels are compatible with
most coatings, but a test patch is suggested. WARNING! If
you scrape, sand or remove old paint from any surface,
you may release lead paint dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS
ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO
AVOID EXPOSURE. Wear a NIOSH approved respirator
to control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
APPLICATION
Before using, stir thoroughly to ensure any settled pigment
is re-dispersed. If necessary, thin the material with
acetone. For brush or roller, thinning is not normally
required. For air spray, thin up to 15% with Acetone. Do
not thin with gasoline, lacquer thinner, turpentine, etc. For
airless spray, thinning is not normally required. Apply with
a good quality brush, roller or spray gun.
Brush: Use light, even strokes Excessive brushing
reduces film thickness and protection.
Roller: A 3/8” nap roller should be used on rough surfaces.
Cover approximately one square yard at a time. Roll away
from previously coated area and work back to it for a
uniform appearance. Use a brush on crevices and sharp
edges.
Spray Gun: Follow spray gun directions carefully. Always
keep the gun ten to twelve inches from the surface and in
motion while spraying.
CLEAN-UP
Clean brush and tools with Mineral Spirits.
TECHNICAL DATA
STOPS RUST ENAMEL BRUSH
Rust-Oleum Corporation Form: CS2155
11 Hawthorn Parkway Phone: 877•385•8155 Rev.: 022613
Vernon Hills, Illinois 60061 www.rustoleum.com
An RPM Company
PHYSICAL PROPERTIES .
High Gloss
Semi-Gloss
Flat
Metallic
Resin Type
Oil modified Alkyd
Oil modified Alkyd
Oil modified Alkyd
Oil modified Alkyd
Pigment Type
Varies with Color
Varies with Color
Varies with Color
Varies with Color
Solvents
Mineral Spirits
Mineral Spirits
Mineral Spirits
Mineral Spirits
Weight
Per Gallon
7.4-9.9 lbs.
8.3-9.9 lbs.
11.0-11.3 lbs.
7.9 lbs.
Per Liter
0.9-1.2 kg
1.0-1.2 kg
1.3-1.4 kg
0.9 kg
Solids
By Weight
51.0-52.2%
52.5-63.0%
54.7-69.7%
46.0%
By Volume
37.0-42.3%
38.5-43.1%
38.1-47.6%
34.5%
Volatile Organic Compounds
<485 g/l
(4.05 lbs./gal.)
<485 g/l
(4.05 lbs./gal.)
<485 g/l
(4.05 lbs./gal.)
<485 g/l
(4.05 lbs./gal.)
Recommended Dry Film
Thickness (DFT) Per Coat
1.5-2.5 mils
(37.5-62.5µ)
1.5-2.5 mils
(37.5-62.5µ)
1.5-2.5 mils
(37.5-62.5µ)
1.5-2.5 mils
(37.5-62.5µ)
Wet Film to Achieve DFT
4.0-6.0 mils
(100-150µ)
4.0-6.0 mils
(100-150µ)
4.0-6.0 mils
(100-150µ)
3.0-4.5 mils
(75-112.5µ)
Theoretical Coverage at
1 mil DFT (25µ)
148-170 sq.ft./qt.
(14.6-16.7 m
2
/l)
154-173 sq.ft./qt.
(15.2-17.0 m
2
/l)
153-191 sq.ft./qt.
(15.0-18.8 m
2
/l)
90-140 sq.ft./qt.
(8.9-13.8 m
2
/l)
Practical Coverage
at Recommended DFT
50-90 sq.ft./qt.
(4.5-8.2 m
2
)
50-100 sq.ft./qt.
(4.5-9.1 m
2
)
50-110 sq.ft./qt.
(4.5-10.0 m
2
)
80-120 sq.ft./qt.
(7.3-10.9 m
2
)
Dry Times at
70°F (21°C) and
50% Relative
Humidity
Touch
2-4 hours
2-4 hours
2-4 hours
2-4 hours
Handle
5-9 hours
5-9 hours
5-9 hours
5-9 hours
Recoat
After 24 hours
After 24 hours
After 24 hours
After 24 hours
Dry Heat Resistance
200°F (93°C)
Shelf Life
5 years
Flash Point
104°F (40°C)
Safety Information
For additional information, see MSDS
  • Page 1 1
  • Page 2 2

Rust-Oleum 239083 User manual

239083
Rust-Oleum
Brand
Rust-Oleum
Model
239083
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents