Toshiba RD-X2U User guide

HDD/DVD VIDEO RECORDER

RD-X2U

OWNER’S MANUAL

DIGITAL VIDEO

INSTALLATION

GUIDE

Read this booklet first.

Introduction

Connections

Basic Setup

RD-X2U.Prep.(E)p01 9/3/02, 9:47 AM1

2

SAFETY PRECAUTIONS

Introduction

The lightning flash with arrowhead symbol, within an equilat-

eral triangle, is intended to alert the user to the presence of

uninsulated “dangerous voltage” within the product’s enclo-

sure that may be of sufficient magnitude to constitute a risk

of electric shock to persons.

The exclamation point within an equilateral triangle is in-

tended to alert the user to the presence of important operat-

ing and maintenance (servicing) instructions in the literature

accompanying the appliance.

The symbol for CLASS II (Double Insulation)

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE

ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL

ONLY.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA

FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

CAUTION: This HDD/DVD video recorder employs a Laser System.

To ensure proper use of this product, please read this owner’s manual carefully and retain for

future reference. Should the unit require maintenance, contact an authorized service location -

see service procedure.

Use of controls or adjustments or performance of procedures other than those specified herein

may result in hazardous radiation exposure.

To prevent direct exposure to laser beam, do not try to open the enclosure.

Visible and invisible laser radiation when open and interlocks defeated.

DO NOT STARE INTO BEAM.

FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rule. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications made to this equipment, not expressly approved by Toshiba, or parties

authorized by Toshiba, could void the user’s authority to operate the equipment.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

RISQUE DE CHOC ELECTRIQUE NE

PAS OUVRIR

WARNING : TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USERSERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RD-X2U.Prep.(E)p02-12 9/3/02, 9:47 AM2

3

Introduction

Connections

Basic Setup

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected

to the grounding system of the building , as close to the point of cable entry as practical.

Copyright

It is permissible to record television programs, film, video tapes and other material only in the event

that third party copyrights and other rights are not violated.

The instructions shall state that an ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in

each pole shall be incorporated in the electrical installation of the building.

CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk

of electric shock do not perform any servicing other than that contained in the operating

instructions unless you are qualified to do so.

In the spaces provided below, record the Model and Serial No. located on the rear panel of your recorder.

Model No. Serial No.

Retain this information for future reference.

Location of the required label

PRODUCT IS CERTIFIED BY THE MANUFACTURER TO

COMPLY WITH DHHS RULE 21 CFR SUBCHAPTER J

APPLICABLE AT THE DATE OF MANUFACTURE.

1-1,SHIBAURA 1-CHOME,MINATO-KU.

MANUFACTURED

TOKYO 105-8001,JAPAN

RD-X2U.Prep.(E)p02-12 9/3/02, 9:47 AM3

4

S3125A

CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS

OWNER’S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR

FUTURE REFERENCE.

This set has been designed and manufactured to assure personal safety. Improper use can result in electric

shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following

procedures for installation, use and servicing. This unit is fully transistorized and does not contain any parts that

can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce

heat.

9. Do not defeat the safety purpose of the

polarized or grounding-type plug. A polarized

plug has two blades with one wider than the

other. A grounding type plug has two blades

and a third grounding prong. The wide blade or

the third prong are provided for your safety. If

the provided plug does not fit into your outlet,

consult an electrician for replacement of the

obsolete outlet.

10.Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from

the apparatus.

11.Only use attachments/accessories specified by

the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to

avoid injury from tip-over.

RD-X2U.Prep.(E)p02-12 9/3/02, 9:47 AM4

5

Introduction

Connections

Basic Setup

Introduction

13.Unplug this apparatus during lightning storms

or when unused for long periods of time.

But if there is thunder or lightning, do not touch

the aerial cable and power cord. This will for

you not to receive the electric shock by the

serge of thunder.

14.Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or

has been dropped.

ADDITIONAL SAFETY INSTRUCTIONS

15.When you use headphones, keep the volume at

a moderate level. If you use the headphones

continuously with high volume sound, it may

cause hearing damage.

16.Do not overload wall outlets; extension cords, or

integral convenience receptacles as this can

result in a risk of fire or electric shock.

17.Apparatus should not be exposed to dripping or

splashing and no objects filled with liquids, such

as vases, should be placed on the apparatus.

18.Keep your fingers well clear of the disc tray as it

is closing. Neglecting to do so may cause

serious personal injury.

19.Do not place a heavy object on or step on the

apparatus. The object may fall, causing serious

personal injury and serious damage to the

apparatus.

20.Do not place the apparatus on amplifiers or

equipment that may produce heat.

21.Do not cover the ventilating holes for the inside

cooling fan.

22.Do not use a cracked, deformed, or repaired

disc. These discs are easily broken and may

cause serious personal injury and apparatus

malfunction.

RD-X2U.Prep.(E)p02-12 9/3/02, 9:47 AM5

6

Precautions

Introduction

Notes on handling

Never disconnect the power cord from a wall outlet

while the recorder is not in standby mode, unless it is

in an emergency. Doing so may cause malfunction.

When shipping the recorder, the original shipping

carton and packing materials come in handy. For

maximum protection, repack the unit as it was

originally packed at the factory.

Do not use volatile liquids, such as insect spray, near

the recorder. Do not leave rubber or plastic products in

contact with the recorder for a long time. They will

leave marks on the finish.

The top and rear panels of the recorder may become

warm after a long period of use. This is not a

malfunction.

When not in use

For usual absence

Be sure to remove the disc from the recorder and turn

off the power.

Prolonged absence

Unplug the recorder from a wall outlet.

Notes on locating

Place the recorder on a level surface. Do not use it on

a shaky or unstable surface such as a wobbly table or

inclined stand. The loaded disc may dislodge from its

proper position and cause damage to the recorder.

Before placing the recorder, make sure that the

surface can stand the weight of the recorder. For

safety, avoid placing the recorder in a high location, as

an accidental fall of the recorder may cause personal

injury.

When you place this recorder near a TV, radio, or

VCR, the playback picture may become poor and the

sound may be distorted depending on the condition

and location of said equipment. In such an event,

place the recorder away as much as possible from the

TV, radio, or VCR.

Notes on cleaning

Use a soft, dry cloth for cleaning.

For stubborn dirt, use a damp cloth (containing a mild

detergent) to wipe the unit. Ensure the unit is

unplugged before you do this. Use a dry cloth to wipe

it dry.

Do not use any type of solvent, such as thinner or

benzine, as they may damage the surface of the

recorder.

If you use a chemical saturated cloth to clean the unit,

follow that product’s instructions.

To obtain a clear picture

The recorder is a high technology, precision device. If the

optical pick-up lens and disc drive parts are dirty or worn

down, the picture quality deteriorates. To obtain a clear

picture, we recommend regular inspection and

maintenance (cleaning or parts replacement) every

1,000 hours of use depending on the operating

environment. For details, contact your nearest dealer.

Notes on antennas

Image and sound quality depend very much on signal

reception.

Reception may be poor in weak signal areas. In this

event, consult your dealer, or purchase a commercially

available antenna booster. Refer to the booster’s

instruction manual for installation details.

RD-X2U.Prep.(E)p02-12 9/3/02, 9:47 AM6

7

Introduction

Connections

Basic Setup

Notes on recording and editing

When you record/edit important content, make trial

operations beforehand to confirm the recorder can

function properly.

Toshiba does not compensate for content which was

not recorded/edited because of some malfunction of

this product or discs during operation, and is not liable

for incidental damages (such as profit loss or

interruption of business, etc.) produced in such

conditions.

When the power cord is disconnected or when a

power failure occurs during any operation of this

product, all contents recorded in this recorder may be

erased.

Depending on the channel or program, an excessive

sound input level may cause noise or cut of recorded

sound. Adjust the initial setting of the recording level

when necessary.

A regular backup of precious recordings is

recommended.

Data in a disc will not be damaged through storage,

however deterioration of a disc may cause error or

erasure of them.

For contents copy-once permitted to protect copyright,

backup is not possible.

Exemptions

Toshiba is not liable for any damage caused by fire,

earthquake, uses by a third person, accidents, owner’s

intentional or unintentional misuse, or uses in other

improper conditions.

Toshiba is not liable for incidental damages (such as

profit loss or interruption in business, modification or

erasure of recorded data, etc.) caused by use or

misuse of this product.

Toshiba is not liable for any damage caused by

neglect of the instructions described in the owner’s

manual.

Toshiba is not liable for any damage caused by misuse

or malfunction through simultaneous use of this

product and the connected equipment or software that

Toshiba is not concerned.

Toshiba does not compensate for contents which was

not recorded/edited because of some malfunctions of

this product or discs during operation, and is not liable

for incidental damages (such as profit loss or

interruption in business, etc.) produced by such

conditions.

Notes on power failure

If the power fails while the recorder is in operation,

content stored in the recorder may be erased. In such as

back up it is recommended that you copy important

content from the recorder to DVD-RAM discs to store

them.

On the unit

Do not give a shock or shake (especially during

operation).

Do not use in a shaky or unstable location.

Hold the unit horizontally.

Do not cover the ventilation holes for the cooling fan of

the unit.

Do not use in a place where the temperature rises or

changes rapidly.

Do not disconnect the power plug from a wall outlet

while the unit is turned on.

Do not disconnect the power plug from the wall outlet

or break the power supply to the unit during recording

or playing. Before disconnecting the power plug, be

sure to press the power button and make sure the unit

ends the finishing process and power turns off

completely. If the power plug is disconnected or power

supply is disrupted while the unit is recording, all

recorded content will be erased.

Toshiba is not liable for any damage or loss of

recorded data caused by shock, shakes, misoperation

or malfunction.

RD-X2U.Prep.(E)p02-12 9/3/02, 9:47 AM7

8

Precautions (Continued)

Notes on HDD

This unit contains a hard disc drive (HDD). An HDD is

subject to shock, shakes, and environmental changes

such as temperature, which can damage data stored on

the disc. Observe the following instructions.

Do not shock or shake the unit (especially during

operation).

Do not use the unit on a shaky or unstable surface.

Do not place the unit on a location where is not

horizontal.

Do not cover the ventilation holes for the cooling fan.

Do not use in a location where the temperature rises

or changes rapidly.

Do not disconnect the power plug from a wall outlet

while the unit is turned on.

Do not disconnect the power plug from a wall outlet or

break power supply to the unit. Before disconnecting

the power plug, be sure to press the power button and

make sure the unit ends the finishing process and the

power turns off completely. If the power plug is

disconnected or power supply is disrupted while the

unit is recording, all recorded content will be erased.

Toshiba is not liable for any damage or loss of

recorded data caused by shock, shakes, misoperation

or malfunction.

Notes on moisture condensation

Moisture condensation damages the unit. Please

read the following carefully.

Moisture condensation occurs, for example, when you

pour a cold drink into a glass on a warm day. Drops of

water form on the outside of the glass. In the same way,

moisture may condense on the optical pick-up lens inside

this unit, one of the most crucial internal parts of the unit.

Moisture condensation occurs during the

following cases.

When you bring the unit directly from a cold place to a

warm place.

When you use the unit in a room where you just

turned on the heater, or a place where the cold wind

from the air conditioner directly hits the unit.

In summer, when you use the unit in a hot and humid

place just after you move the unit from an air

conditioned room.

When you use the unit in a humid place.

Do not use the unit when moisture condensation

occurs.

If you use the unit in such a situation, it may damage

discs and internal parts. Remove the disc, connect the

power cord of the unit to the wall outlet, turn on the

unit, and leave it for two or three hours. After two or

three hours, the unit will have warmed up and

evaporated any moisture. Keep the unit connected to

the wall outlet and moisture condensation will seldom

occur.

Introduction

E

x

a

m

p

l

e

o

f

m

o

i

s

t

u

r

e

c

o

n

d

e

n

s

a

t

i

o

n

!

Optical pick-up

lens

It’s too

warm!

Wait!

Wall outlet

RD-X2U.Prep.(E)p02-12 9/3/02, 9:47 AM8

9

Introduction

Connections

Basic Setup

Notes on copyright

It is prohibited by law to copy, broadcast, show,

broadcast on cable, play in public, and rent

copyrighted material without permission.

Some DVD video discs are copy protected, and any

recordings made from these discs will be distorted.

This unit incorporates copyright protection technology

under method claims of certain U.S. patents and other

intellectual property rights owned by Macrovision

Corporation and other rights owners. Use of this

copyright protection technology must be authorized by

Macrovision Corporation, and is intended for home

and other limited viewing uses only unless otherwise

authorized by Macrovision Corporation. Reverse

engineering or disassembly is prohibited.

This unit incorporates CPRM (Content Protection for

Recording Media) technology for copyright protection

in recording devices, authorized by DVD forum.

Recording and copying on this recorder depend on the

contents as described below:

VCR Plus+ and PlusCode are registered trademarks of

Gemstar Development Corporation. The VCR Plus+

system is manufactured under license from Gemstar

Development Corporation.

Copy free

Can be

recorded

Can be

copied

DVD-RAM

disc

Cannot be

copied

Cannot be

copied

DVD-RAM

disc

DVD-RAM

disc

Can be

copied

DVD-RAM

disc

DVD-RAM

disc

Copy free

Can be

recorded

Can be

recorded

Recording once

permitted

Can be

recorded

Recording prohibited

Cannot be

recorded

Cannot be

recorded

HDD:Hard Disc Drive

Program Recording Copy

HDD

Recording once

permitted

Recording once

permitted

Moving (Deleting the original one after dubbing) of

record once permitted content is only possible in the

direction from the HDD to the DVD-RAM drive.

Copy prohibited or copy restricted content cannot be

recorded onto a DVD-RAM disc.

RD-X2U.Prep.(E)p02-12 9/3/02, 9:47 AM9

10

Installation procedure

Introduction

Load the batteries in the remote control.

( page 12)

Connect antenna to the recorder.

( page 14)

Connect a cable box or satellite system to the recorder.

(

pages 16 to 18)

Connect the recorder to a TV.

( pages 14 to 15, 19)

Connect optional equipment to the recorder.

( pages 20 to 23)

Make the initial settings.

( page 26)

Your recorder is ready. Read the separate

volume “OPERATIONS”.

Accessories

Remote control

Batteries (AAA) x 2

Power Cord

Coaxial cable

Video cable

• Registration card

• Diagnostic list

Audio cable

Read carefully “SAFETY PRECAUTIONS” and

“Precautions”.

( pages 2 to 9)

Check the supplied accessories.

(See right)

RD-X2U.Prep.(E)p02-12 9/3/02, 9:47 AM10

11

Introduction

Connections

Basic Setup

Introduction

SAFETY PRECAUTIONS ...................................................................................................... 2

IMPORTANT SAFETY INSTRUCTIONS ............................................................................... 4

Precautions........................................................................................................................... 6

Installation procedure........................................................................................................ 10

Preparation of the remote control .................................................................................... 12

Connections

Connecting an antenna and TV......................................................................................... 14

Connecting to a cable box ................................................................................................ 16

Connecting to a satellite system ...................................................................................... 18

Connecting to a TV equipped with component video inputs ......................................... 19

Connecting to an audio system........................................................................................ 20

Connecting to an amplifier equipped with a Dolby Digital decoder ....................... 21

Connecting to an amplifier equipped with Dolby Surround Pro Logic ................... 21

Connecting to an amplifier equipped with a DTS decoder .................................... 22

Connecting to an amplifier equipped with an MPEG2 audio decoder ................... 22

Connecting to an amplifier equipped with a digital audio input ............................. 23

Basic Setup

Starting up the recorder .................................................................................................... 26

A: Initial Settings ................................................................................................................ 28

1: Time and Date Setting ....................................................................................... 30

2: Channel Setting ................................................................................................. 33

3: Guide Channel Setting ...................................................................................... 36

4: Cable Box/DSS

®

Setting .................................................................................... 38

B: Output sound setting .................................................................................................... 40

C: TV shape setting ............................................................................................................ 42

D: Remote control settings ............................................................................................... 44

Operating a TV with the remote control of this recorder........................................ 44

Operating 2 HDD&DVD recorders with the remote control of this recorder .......... 46

LIMITED WARRANTY HDD/DVD VIDEO RECORDER ...................................................... 48

Introduction

Table of Contents

RD-X2U.Prep.(E)p02-12 9/3/02, 9:47 AM11

12

Introduction

Preparation of the remote control

Operating with the remote control

Point the remote control at the remote sensor and

press the buttons.

Distance:About 7 m (23 ft) from the front of the

remote sensor

Angle :About 30° in each direction of the front of

the remote sensor

* Do not expose the remote sensor of the recorder to a

strong light source such as direct sunlight or other

illumination. If you do so, you may not be able to

operate the recorder via the remote control.

Notes

• Direct the remote control at the remote sensor of the

recorder.

• Do not drop or give the remote control a shock.

• Do not leave the remote control near an extremely hot or

humid place.

• Do not spill water or put anything wet on the remote control.

• Do not open the remote control.

1

Open the cover.

2

Insert batteries (AAA size).

Make sure to match the + and – on the

batteries to the marks inside the battery

compartment.

3

Close the cover.

Notes on batteries

Improper use of batteries may cause battery leakage and

corrosion. To operate the remote control correctly, follow the

instructions below.

• Do not insert batteries into the remote control in the wrong

direction.

• Do not charge, heat, open, or short-circuit the batteries. Do

not throw batteries into a fire.

• Do not leave dead or exhausted batteries in the remote

control.

• Do not use different types of batteries together, or mix old

and new batteries.

• If you do not use the remote control for a long period of

time, remove the batteries to avoid possible damage from

battery corrosion.

• If the remote control does not function correctly or if the

operating range is reduced, replace all batteries with new

ones.

• If battery leakage occurs, wipe the battery liquid from the

battery compartment, then insert new batteries.

30°

Within about 7 m (23 ft)

RD-X2U.Prep.(E)p02-12 9/3/02, 9:47 AM12

1

2

3

4

ON/STANDBY

HDD TIMESLIP DVD

Connections

Connect your recorder to your TV or stereo system.

Connecting an antenna and TV

Connecting to a cable box

Connecting to a satellite system

Connecting to a TV equipped

with component video inputs

Connecting to an audio system

Connection procedure

When you connect a TV equipped with audio/

video inputs

Perform steps 1, 2 and 3.

When you connect an audio system

Perform steps 1, 2, 3 and 4.

“Connecting an antenna

and TV” ( page 14)

“Connecting an antenna

and TV” ( page 14)

“Connecting to a TV

equipped with

audio/video inputs”

( page 15)

“Connecting to an audio

system” ( page 20)

AV amplifier

RD-X2U.Prep.(E)p13-24 9/3/02, 9:47 AM13

14

Connecting an antenna and TV

Connect your TV and the antenna to this recorder for recording and to view broadcast signals on the TV.

Connections

1

Disconnect the antenna cable from your TV, and connect it to the RF IN

(FROM ANT.) terminal on the recorder.

2

Using the supplied coaxial cable of this recorder, connect the RF OUT (TO

TV) terminal to the TV.

Connector types of an antenna cable varies depending on the TV.

Check the type on your TV, and connect properly using one of the following methods.

VHF/UHF

Coaxial cable

Antenna splitter

TV antenna input

VHF/UHF antenna

Antenna cable

To RF IN (FROM ANT.)

TV

To RF OUT (TO TV)

Coaxial cable

To antenna input

e.g. e.g.

For connecting to a cable box or a satellite system, see

page 16 to 18.

Notes

• This connection insures accessibility of broadcast signals to your TV only. Unlike a VCR, you can not assign channel 3 or 4

for playback of this recorder. You must connect this recorder to a video input of your television to enjoy playback picture from

this recorder.

RD-X2U.Prep.(E)p13-24 9/3/02, 9:47 AM14

15

Connections

Basic Setup

Introduction

To wall outlet

To OUTPUT1 (L/R)

Notes

• Refer to the owner’s manual of the connected TV as well.

• When you connect the recorder to your TV, be sure to turn off the power and unplug both units from the wall outlet before any

connections.

• If your television set has one audio input, connect the left and right audio outputs of the recorder to a Y cable adapter (not

supplied) and then connect to your TV.

• Connect the recorder directly to your TV. If you connect the recorder to a VCR, TV/VCR combination or video selector, the

playback picture may be distorted due to copy protection.

To OUTPUT1

(VIDEO)

To OUTPUT1

(S-VIDEO)

Audio cable

(supplied)

If the TV has an S-video input, connect the recorder

with an S-video cable. When using an S-video

cable, do not connect the yellow video cable.

(yellow)(white)(red)

(red)

(yellow)

(white)

To video inputs

To audio input

To S-video input

TV or monitor with audio/video inputs

3

Connect to a TV equiped with audio/video inputs.

Connect as below for watching received channels or recorded contents. Watching via the RF OUT terminal

is not available.

4

Connect the power cord of the recorder to a wall outlet.

Make sure that the powered recorder lights the ON/STANDBY indicator on the front panel.

video cable

(supplied)

RD-X2U.Prep.(E)p13-24 9/3/02, 9:47 AM15

16

3CH

4CH

3CH

4CH

Connecting to a cable box

Choose one of the below according to your usage of the cable box.

For watching received channels, connect to the TV via the audio/video cable.

Connections

This set-up will allow you to:

– record an unscrambled channel.

– record an unscrambled channel while watching

another (only when you connect a cable-compatible

TV).

You will need to:

• to record a channel while watching another, select a

desired channel on the TV (only when you connect a

cable-compatible TV).

This set-up will allow you to:

– record an unscrambled channel.

– record an unscrambled channel while watching

another (scrambled or unscrambled).

You will need to:

• set TV channel to the output channel of the cable box.

• to record an unscrambled channel while watching a

scrambled ohannel, select a desired cable channel via

the cable box.

This set-up will allow you to:

– record any channels through the cable box.

You will need to:

• set “Cable Box/DSS” to “Use” on the “Initial Settings”

menu.

page 38

• set “Output Channel” to “3CH” or “4CH” on the “Initial

Settings” menu.

page 39

• select a desired cable channel via the cable box.

• while the recorder is turned off, set TV channel to the

output channel of the cable box.

Incoming cable

Cable box

IN OUT

RD-X2U.Prep.(E)p13-24 9/3/02, 9:47 AM16

17

Connections

Basic Setup

Introduction

This set-up will allow you to:

– record an unscrambled or scrambled channel.

– record an unscrambled channel while watching

another unscrambled channel (only when you connect

a cable-compatible TV).

You will need to:

• A/B switch “A”: record an unscrambled channel which

bypasses the cable box.

• A/B switch “B”: record a scrambled or unscrambled

channel coming through the cable box.

– set “Cable Box/DSS” to “Use” on the

“Initial Settings” menu.

page 38

– set “Output Channel” to “3CH” or

“4CH” on the “Initial Settings” menu.

page 39

This set-up will allow you to:

– watch or record a channel through the cable box via

the INPUT1 jacks.

You will need to:

• set “Cable Box/DSS” to “Use” on the “Initial Settings”

menu.

page 38

• set “Output Channel” on the “Initial Settings” to “Line 1”

menu.

page 39

Cable box

A/B switch

A

B

Cable box

IN OUT

IN

3CH

4CH

RD-X2U.Prep.(E)p13-24 9/3/02, 9:47 AM17

18

Connecting to a satellite system

Choose one of the following according to your type of satellite receiver.

Connections

When the satellite receiver does not have audio/

video inputs

1 Connect a satellite antenna to the satellite receiver.

2 Connect the RF IN (FROM ANT.) terminal on the

recorder and the RF OUT terminal of the satellite

receiver.

3 Connect the RF OUT (TO TV) terminal on the recorder

and the antenna input connector of the TV.

You will need to:

• set “Cable Box/DSS” to “Use” on the “Initial Settings”

menu.

page 38

• set “Output Channel” to “3CH” or “4CH” on the “Initial

Settings” menu.

page 39

When the satellite system has audio/video outputs

1 Connect a satellite antenna to the satellite system.

2 Connect the INPUT1 (VIDEO/L/R) jacks on the

recorder and the audio/video output jacks of the

satellite system.

3 Connect the OUTPUT1 (VIDEO/L/R) jacks on the

recorder and the audio/video input jacks of the TV.

4 Connect the RF OUT (TO TV) terminal on the recorder

and the antenna input connector of the TV.

You will need to:

• set “Cable Box/DSS” to “Use” on the “Initial Settings”

menu.

page 38

• set “Output Channel” to “Line 1” on the “Initial Settings”

menu.

page 39

DSS

®

satellite receiver

Satellite antenna

DSS

®

satellite

receiver

Satellite antenna

Incoming cable

Audio/video outputs

IN OUT

IN

3CH

4CH

RD-X2U.Prep.(E)p13-24 9/3/02, 9:47 AM18

19

Connections

Basic Setup

Introduction

Connecting to a TV equipped with component video inputs

If your TV has component video inputs, you can obtain pictures in better quality.

Connections

• Make the following setting.

On-screen display

Select

Page

“Audio Out Select”“Analog 2ch” page 40

Component video outputs/inputs

Some TVs or monitors are equipped with component

video inputs. Connecting to these inputs allows you to

enjoy higher quality picture playback.

Actual labels for component video inputs may vary

depending on the TV manufacturer. (ex.Y, R-Y, R-B or Y,

C

B, CR)

In some TVs or monitors, the color levels of the playback

picture may be reduced slightly or the tint may change. In

such a case, adjust the TV or monitor for optimum

performance.

Notes

• Refer to the owner’s manual of the connected TV as well.

• When you connect the recorder to other equipment, be sure to turn off the power and unplug all of the equipment from the

wall outlet before any connections.

• If you place the recorder near a tuner or radio, the radio broadcast sound might be distorted. In this event, place the recorder

away from the tuner and radio.

• The output sound of the recorder has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening

level. Otherwise, the speakers may be damaged by a sudden high volume sound.

• Turn off the amplifier before you connect or disconnect the recorder’s power cord. If you leave the amplifier power on, the

speakers may be damaged.

To audio

inputs of the

amplifier

To P

R

VIDEO

OUT

(white)

(red)

(white)

(red)

To P

B

VIDEO

OUT

To Y

VIDEO

OUT

To Y video input

To P

B video input

To P

R video input

TV or monitor

equipped with

component

video

(INTERLACED)

inputs

RD-X2U.Prep.(E)p13-24 9/3/02, 9:47 AM19

20

Connecting to an audio system

You can enjoy high quality dynamic sounds by connecting the recorder to optional audio equipment.

Connections

• For connection to your TV, see pages 14 to 15, 19.

• For details of output sound, see

page 55 of

“OPERATIONS”.

• This section uses the following reference marks.

Notes

• DO NOT connect the BITSTREAM/PCM AUDIO OUT jack

of the recorder to the AC-3 RF input of a Dolby Digital

Receiver. This input on your A/V Receiver is reserved for

Laserdisc use only and is incompatible with the

BITSTREAM/PCM AUDIO OUT jack of the recorder.

• Connect the BITSTREAM/PCM AUDIO OUT jack of the

recorder to the “OPTICAL” or “COAXIAL” input of a

Receiver or Processor.

• Refer to the owner’s manual of the connected equipment

as well.

• When you connect the recorder to other equipment, be

sure to turn off the power and unplug all of the equipment

from the wall outlet before any connections.

• The output sound of the recorder has a wide dynamic

range. Be sure to adjust the receiver’s volume to a

moderate listening level. Otherwise, the speakers may be

damaged by a sudden high volume sound.

• Turn off the amplifier before you connect or disconnect the

recorder’s power cord. If you leave the amplifier power on,

the speakers may be damaged.

Warning

• When you are connecting (via the BITSTREAM/PCM

AUDIO OUT jack) an AV decoder that does not have

Dolby Digital, Digital Theater Systems (DTS) or MPEG2

decoding function, be sure to set “Audio Out Select” to

“PCM” from the on-screen displays ( page 40).

Otherwise, high volume sound may damage your

hearing as well as the speakers.

• When playing DTS-encoded discs (DVD video discs

and audio CDs), excessive noise may be output from

the analog stereo jacks. To avoid possible damage to

the audio system, you should take proper precautions

when the analog audio out (L/R) jacks of the recorder

are connected to an amplification system. To enjoy

DTS Digital Surround™ playback, an external 5.1

channel DTS Digital Surround™ decoder system must

be connected to the BITSTREAM/PCM AUDIO OUT

jack of the recorder.

Front speaker

Surround speaker

Sub woofer

Center speaker

Signal flow

RD-X2U.Prep.(E)p13-24 9/3/02, 9:47 AM20

Page is loading ...

Toshiba RD-X2U User guide

Toshiba RD-X2U User guide

Related papers

Other documents