Shimano FH-M629 Service Instructions

FH-M629
Shimano
Brand
Shimano
Model
FH-M629
Type
Service Instructions

This manual is also suitable for

H
Y
P
E
R
G
L
I
D
E
-
C
J
A
P
A
N
U
.
S
.
P
A
T
4
2
6
8
2
5
9
L
O
C
K
4
0
0
k
g
/
c
m
O
N
A
M
I
H
S
ap
as
34T
ap
as
30T
ap
as
26T
ap
as
23T
as
20T
17T
as
au
11T
as
au
13T
as
au
15T
C
S
-
6
J
P
A
A
N
M
9
0
H
P
Y
E
E
R
G
L
I
D
11
T
34T
ap
a
Q
ba
ar
16T
ap
a
Q
ba
ar
16T
ap
a
Q
ar
ba
14T
ap
a
Q
ar
ba
14T
9S
9S
9S
13T
12T
a
Q
ar
ba
12T
a
Q
ar
ba
11T
a
Q
a
r
ba
C
S
-
6
J
P
A
A
N
M
9
0
H
P
Y
E
E
R
G
L
I
D
11
T
C
S
-
6
J
P
A
A
N
M
9
0
H
P
Y
E
E
R
G
L
I
D
11
T
ap
a
Q
ar
ba
14T
CS-HG61 (ar)
CS-HG61 (au)
CS-HG61 (bg)
CS-HG61 (bh)
Lock ring
Lock ring
Lock ring
Sprocket spacers
Lock ring
General Safety Information
WARNING
• Check that the wheels are fastened securely before riding the bicycle. If the wheels are
loose in any way, they may come off the bicycle and serious injury may result.
• Obtain and read the service instructions carefully prior to installing the parts. Loose,
worn or damaged parts may cause the bicycle to fall over and serious injury may occur as
a result. We strongly recommend only using genuine Shimano replacement parts.
• Read these Technical Service Instructions carefully, and keep them in a safe place for
later reference.
• If the CS-HG61 cassette sprocket (12-36T) is installed onto a mountain bike, a large gear
ratio between front and rear rings can be obtained so that the mountain bike can ride up
steep slopes, but this will also place a heavy load on the rear hub. Shimano provides a
rear hub which can provide enough strength and durability if using this cassette sprocket
in combination with a front chainwheel set (22-32-44T).
If using the cassette sprocket in combination with any hub other than the FH-M629/FH-
M529, the hub may become damaged. Check the Shimano website for the most up-to-
date information regarding compatible Shimano hubs. (http://www.shimano.com)
Note
• The FH-M629/FH-M529 is compatible with the CS-HG61 (12-36T).
• Use the CS-HG61 in combination with 9-speed chains (CN-7701 / HG93 / HG73 / HG53).
• If the wheel becomes stiff and difficult to turn, you should lubricate it with grease.
• Do not apply any oil to the inside of the hub, otherwise the grease will come out.
• You should periodically wash the sprockets in a neutral detergent and then lubricate them
again. In addition, cleaning the chain with neutral detergent and lubricating it can be a
effective way of extending the useful life of the sprockets and the chain.
• If the chain keeps coming off the sprockets during use, replace the sprockets and the
chain.
• Parts are not guaranteed against natural wear or deterioration resulting from normal use.
• For maximum performance we highly recommend Shimano lubricants and maintenance
products.
CAUTION
Please note: specifications are subject to change for improvement without notice. (English)
© Jan. 2009 by Shimano Inc. XBC
IZM Printed in Malaysia.
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222
3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
Technical Service Instructions SI-3SY0A-001
FH-M629 / FH-M595
FH-M590 / FH-M529
SI-3SY0A-001-00
00
Freehub
Specifications
Model number
CS-HG61
Group name
ar
au
Gears
9
9
Tooth combination
11, 12, 14, 16, 18, 21, 24, 28, 32T
11, 13, 15, 17, 20, 23, 26, 30, 34T
Cassette sprocket tooth combination
bg
9 11, 12, 13, 14, 16, 18, 21, 24, 28T
bh
*
9 12, 14, 16, 18, 21, 24, 28, 32, 36T
Model number
Gears
FH-M529 / FH-M595
FH-M590 / FH-M629
9
36 / 32No. of spoke holes
Freehub
Installation of the sprockets
For each sprocket, the surface that has
the group mark should face outward and
be positioned so that the wider part of
each sprocket and the A part (where the
groove width is wide) of the freewheel
body are aligned.
The groove is
wide at one
place only.
a
c
-
1
4
T
A
Wide part
• For installation of the sprockets, use the special tool (TL-LR15)
to tighten the lock ring.
* Applicable freehub : FH-M629 / FH-M529
• To replace the sprockets, use the special tool (TL-LR15) and
TL-SR21 to remove the lock ring.
Tightening torque:
30 - 50 N·m {261 - 434 in. lbs.}
Lock ring
Tool
(TL-SR21)
Disassembly
TL-LR15
Replacement of the freewheel body
After removing the hub
axle, remove the freewheel
body fixing bolt (inside
the freewheel body),
and then replace the
freewheel body.
Note: Do not attempt to
disassemble the
freewheel body, because it
may result in a malfunction.
Freewheel body Freewheel body fixing bolt
10 mm Allen key
(TL-WR37)
Disassembly
Assembly
Tightening torque :
35 - 50 N·m {305 - 434 in. lbs.}
Check that the spokes have been laced
as shown in the illustration.
A radial assembly cannot be used.
Rotating direction
of wheel
<FH-M629 / FH-M595 / FH-M529>
Rear left Rear right
Wheel spoke lacing
  • Page 1 1

Shimano FH-M629 Service Instructions

FH-M629
Shimano
Brand
Shimano
Model
FH-M629
Type
Service Instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents