Pulsar AWZ05121 - v1.1 Operating instructions

Brand: Pulsar

Model: AWZ05121 - v1.1

Type: Operating instructions

Pulsar AWZ05121 - v1.1 is a linear power supply unit designed for CCTV applications, providing a stable 12V DC output with a maximum current of 1A. It features 5 independently fused outputs, each protected with either traditional fuses or PTC polymer fuses, selectable via jumpers. The output voltage can be adjusted within a range of 11V to 15V DC, making it suitable for a variety of devices. The unit includes LED indication for output status, AC power, and overvoltage protection, as well as protection against short circuits, overloads, overheating, and tampering.

AWZ 05121

v.1.1

AWZ 12V/1A/5x0,5A

Linear power supply unit for CCTV

EN**

Edition: 5 from 17.03.2014

Supersedes the edition: 4 from 10.12.2013

www.pulsar.pl AWZ05121 GREY POWER CCTV

Features:

 supply output 12VDC/max.1A (5x0,5A)

 output voltage adjustment range

11V÷15VDC

 mains supply of 230VAC

 linear voltage stabilization

 5 outputs protected independently with

0,5A fuses

 jumper selectable fuse type: fuse or

polymer fuse

 LED indication

 protections:

 SCP short circuit protection

 OLP overload protection

 OHP overheat protection

 surge protection

 OVP over voltage protection

 against tampering

 warranty – 5 year from the production date

CONTENTS:

1. Technical description.

1.1. General description.

1.2. Block diagram.

1.3. Description of PSU components and connectors.

1.4. Specifications.

2. Installation.

2.1. Requirements.

2.2. Installation procedure.

3. PSU operating status indication.

3.1. LED indication.

4. Operation and use.

4.1. Short circuit protection.

4.2. Overload protection.

4.3. Maintenance

1. Technical description.

1.1. General description.

The linear PSU is intended for 230V AC mains supply to CCTV devices that require stabilised voltage of

12V DC with current efficiency of 1A. The outputs of the PSU are protected separately with either fuses or polymer

fuse (5x0,5A). Fuse type selection is done by jumpers. The PSU design enables quick change of output voltage

within the range of 11V to 15V DC. The unit is protected against a short circuit, an overload, overheat, a surge and

tampering. The PSU is housed in a metallic enclosure that features a microswitch indicating unwanted opening of

the front door (faceplate).

Before mounting the PSU module, perform a load balance. During normal operation, total current

drawn by the receivers cannot exceed 1A (P=12W max.).

1.2. Block diagram. (fig.1).

Fig.1. Block diagram of the PSU.

www.pulsar.pl AWZ05121 GREY POWER CCTV

1.3. Description of PSU components and connectors.

Table 1. The components of the PSU's pcb (see fig. 2).

Element no. Description

[1]

LED indication:

L1, L2, L3, L4, L5: outputs status indication

AC AC power indication (on the pcb)

[2] F1, F2, F3, F4, F5: 0,5A fuses in the output circuit (DC)

[3] P1 potentiometer, output voltage adjustment range 11V÷15V DC

[4]

Connectors:

+O1 ÷ O5

DC power outputs

(„+” = Vcc, „−” = GND)

[5]

Fuse selection jumper

[6] LED indicating activation of the over voltage protection OVP

Fig.2. The view of the PSU’s pcb.

Table 2. Elements of the PSU (see fig. 3).

Element no. Description

[1] Isolation transformer

[2] Pcb of the PSU (Tab. 1, Fig. 2)

[3] TAMPER; microswitches (contacts) of tampering protection (NC)

[4] F

MAIN

fuse in the battery circuit (230V/AC)

[5]

L-N 230V/AC power supply connector, PE protection connector

www.pulsar.pl AWZ05121 GREY POWER CCTV

Fig. 3. The view of the PSU.

1.4. Specifications:

- electrical specifications (tab.3)

- mechanical specifications (tab.4)

- operation safety (tab.5)

- operating specifications (tab.6)

Electrical specifications (tab. 3).

Mains supply 230V AC (-15%/+10%)

Current consumption 0.15A

Power frequency 50Hz

PSU power 12W max.

Output voltage 12V DC

Output current 5 x 0,2A for F 500mA fuses

Ic= 1A max (total, continuous) @12V DC

Output voltage adjustment range 11V÷15V DC

Output voltage escalation, decrease,

and keeping time

40ms/70ms/20ms

Short-circuit protection SCP

5 x F 500mA fuse (damage requires fuse-element replacement or

PTC 500mA – jumper selectable.

Overload protection OLP

110% ÷ 150% (@25ºC) of PSU power - current limiting by the

PTC resettable fuse, manual restart (failure demands cutting off

the DC output circuit)

Over voltage protection OVP

U>17V (-/+ 5%) disconnection of the output voltage, automatic

return

Surge protection varistors

Overheat protection electronic

Tampering protection system:

- TAMPER – indicating unwanted

opening of the PSU’s enclosure

- a microswitch, NC contacts (enclosure closed) 0,5A@50V DC

(max.)

LED indication:

LEDs 1÷5 (green)

LED AC (red, on the PSU's pcb)

- status of outputs: +O1…+O5:

normal status = on

failure= off

- AC power status:

www.pulsar.pl AWZ05121 GREY POWER CCTV

normal status = on

failure= off

F fuse

F1÷F5 fuse

T 315mA/250V

F 500mA/ 250V

Mechanical specifications (tab. 4).

Enclosure dimensions 170 x 180 x 80+8 [mm] (WxHxD)

Fixing 145 x 174 x Φ 6 WxH

Net/gross weight 1,61 /1,69 kg

Enclosure colour Steel plate DC01 0,7mm thick, colour RAL9003

Closing Cheese head screw (at the front)

Connectors Mains power 230V AC: Φ0,63-2,05 (AWG 22-12)

DC outputs: Φ0,51- 2,05 (AWG 24-12)

TAMPER output: wires 25cm

Notes The enclosure does not adjoin the assembly surface so that cables can be

led.Convectional cooling.

Operation safety (tab.5).

Protection class PN-EN 60950-1:2007 I (first)

Degree of Protection PN-EN 60529: 2002 (U) IP20

Electrical strength of insulation:

- between input and output circuits of the PSU (I/P-O/P)

- between input circuit and PE protection circuit (I/P-FG)

- between output circuit and PE protection circuit (O/P-FG)

3000V AC min.

1500V AC min.

500V AC min.

Insulation resistance:

- between input circuit and output or protection circuit

100 MΩ, 500V DC

Operating specifications (tab.6).

Operating temperature -10ºC...+40ºC

Storage temperature -20ºC...+60ºC

Relative humidity 20%...90%, without condensation

Vibrations during operation unacceptable

Impulse waves during operation unacceptable

Direct insolation unacceptable

Vibrations and impulse waves during transport PN-83/T-42106

2. Installation

2.1. Requirements.

The stabilized PSU is to be mounted by a qualified installer, holding relevant permits and licenses

(applicable and required for a given country) for 230V/AC interference and low-voltage installations. The unit

should be mounted in confined spaces, in accordance with the 2nd environmental class, with normal relative

humidity (RH=90% maximum, without condensation) and temperature from -10°C to +40°C. The PSU shall work in

a vertical position that guarantees sufficient convectional air-flow through ventilating holes of the enclosure.

Before mounting the PSU module, perform a load balance. During normal operation, total

current drawn by the receivers cannot exceed I=1A (P=12W max.). The change of the original

fuse value is acceptable unless all power outputs are in use and Pmax is exceeded.

As the PSU is designed for a continuous operation and is not equipped with a power-switch,

therefore an appropriate overload protection shall be guaranteed in the power supply circuit. Moreover, the user

shall be informed about the method of unplugging (usually through assigning an appropriate fuse in the fuse-box).

The electrical system shall follow valid standards and regulations.

www.pulsar.pl AWZ05121 GREY POWER CCTV

2.2. Installation procedure.

1. Before installation, make sure that the voltage in the 230V power-supply circuit is cut off.

2. Mount the PSU in a selected location and connect the wires.

3. Remove the mains fuse that protects the primal circuit.

4. Connect the power cables to the L-N terminals. Connect the ground wire to the terminal marked by the earth

symbol – “ ”. Use a three-core cable (with a yellow and green PE protection wire) to make the connection. Lead

the cables to the appropriate terminals of the connection board through the bushing.

The shock protection circuit shall be performed with a particular care, i.e. the yellow and

green wire coat of the power cable shall stick to one side of the terminal marked with the ' '

earth symbol in the PSU enclosure. Operation of the power supply without a properly made

and fully operational shock protection circuit is UNACCEPTABLE! It can result in device

damage or an electric shock.

5. Connect the receivers’ cables to the connectors:+O1…..+O5 (keeping the polarisation).

6. In case of installation where significant voltage drops occur in the resistance of the cables leading to the

receivers, there is a possibility of voltage value correction by a potentiometer P1 (11V÷15V DC).

7. Insert the fuse in the power circuit and switch on the power.

8. Check the LED indication for PSU operating status.

9. Once the installation and operation control have been completed, the enclosure can be locked.

3. Operating status indication.

The PSU is equipped with LED indication of operation status. The presence of power at the outputs of the PSU is

indicated by the illumination of green LEDs on the faceplate of the device.

3.1. LED indication (fig. 4)

 L1….L5 green LEDs indicate power at the outputs: +O1…..+O5.

In case of a power loss at the output (fuse activation), an appropriate diode goes out ((L1 for +O1, L2 for +O2

etc.).

 LED AC red diode power status at the PSU output. In case of a power loss at the output (absence of 230V

AC power, F damage), the diode is off.

Fig. 4. The view of the PSU panel.

www.pulsar.pl AWZ05121 GREY POWER CCTV

4. Operation and use.

4.1. Procedure in case of a short circuit (SCP activation) at the PSU output.

The O1÷ O5 PSU outputs are protected against a short circuit by fuses or polymer fuse.

In case of fuse damage, replace the fuse of the same parameters.

If the polymer fuse -assisted protection has been chosen, there will be an automatic disconnection of the

output voltage indicated by the green diode going out. Then, cut off the main power or the load from the PSU

output for approx. 1 minute.

The change of the original fuses is acceptable unless all power outputs are in use and Pmax is exceeded.

4.2. Procedure in case of an overload (OLP activation).

Main output of the PSU is protected against an overload by polymer fuse. If the PSU load exceeds 1A the

output voltage is cut off automatically and indicated by all LEDs going off. Restoration of the voltage at the output

requires disconnection of the outputs or cutting off the main power (230V AC) for approx. 1 minute.

4.3. Maintenance.

Any and all maintenance operations may be performed following the disconnection of the PSU from the

power supply network. The PSU does not require performing any specific maintenance measures. However, in

case of a significant level of dust, clean the interior with compressed air. In case of a fuse exchange, use a

replacement of the same parameters.

www.pulsar.pl AWZ05121 GREY POWER CCTV

WEEE MARK

According to the EU WEE Directive – It is required not to dispose of electric or

electronic waste as unsorted municipal waste and to collect such WEEE separately.

Pulsar K.Bogusz Sp.j.

Siedlec 150,

32-744 Łapczyca, Poland

Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50

e-mail: biuro@pulsar.pl, sales@pulsar.pl

http:// www.pulsar.pl, www.zasilacze.pl

GENERAL WARRANTY CONDITIONS

1. Pulsar K. Bogusz Sp.j. (the manufacturer) grants a five-year warranty for the equipment, counted from the device’s production

date.

2. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (the selection is at the

manufacturer’s discretion) if the malfunction is due to the manufacturer, includes manufacturing or material defects, unless such

defects have been reported within the warranty period (item 1).

3. The equipment subject to warranty is to be brought to the place where it was purchased, or directly to the main office of the

manufacturer.

4. The warranty applies to complete equipment, accompanied by a properly filled warranty claim with a description of the defect.

5. Should the claim be accepted, the manufacturer is obliged to provide warranty repairs, at the earliest convenience, however not

later that within 14 days from the delivery to the service centre of the manufacturer.

6. The repair period mentioned in item 5 may be prolonged, if there are no technical possibilities to carry out the repairs, or if the

equipment has been conditionally accepted, due to the breaking warranty terms by the claimant.

7. All the services rendered by force of the warranty are carried out at the service centre of the manufacturer, exclusively.

8. The warranty does not cover the defects of the equipment, resulting from:

- reasons beyond the manufacturer's control,

- mechanical damage,

- improper storage and transport,

- use that violates the operation manual or equipment’s intended use

- fortuitous events, including lightning discharges, power failures, fire, flood, high temperatures and chemical agents,

- improper installation and configuration (in defiance with the manual),

9. The warranty is void in any of the following circumstances:

- construction changes

- repairs carried out by any unauthorized service center

- damage or removal of warranty labels

- modifications of the serial number

10. The liability of the manufacturer towards the buyer is limited to the value of the equipment, determined according to the

wholesale prices suggested by the manufacturer on the day of purchase.

11. The manufacturer takes no responsibility for the defects that result from:

- the damaging, malfunctioning or inability to operate the equipment

- defects that result from using the equipment outside its stated specifications and operating parameters failing to abide by the

recommendations and requirements contained in the manual, or the use of the equipment.

Pulsar AWZ05121 - v1.1 Operating instructions

Pulsar AWZ05121 - v1.1 Operating instructions

Pulsar AWZ05121 - v1.1 Operating instructions

Related papers

Other documents