Steren AMP-210SD Owner's manual

Page is loading ...

6

3. CONTROLES

PANEL FRONTAL

PANEL TRASERO

Page is loading ...

2

Thank You on purchasing your new Steren product.

This manual includes all the feature operations and troubleshooting

necessary to install and operate your new 210 W P.A. amplier

with SD card reader.

Please review this manual thoroughly to ensure proper

installation and operation of this product. For support, shopping,

and everything new at Steren, visit our website:

www.steren.com

AMP-210SD

210 W P.A. AMPLIFIER WITH SD

CARD READER

The instructions of this manual are for reference about the product.

There may be differences due to updates.

Please check our web site (www.steren.com) to obtain the latest

version of the instruction manual.

3

IMPORTANT

• Verify line voltage before use.

• If you have any questions about the voltage requirements for your specic model,

or about the line voltage in your area, contact your selling dealer before plugging the

unit into a wall outlet.

• Do not use extension cords.

• To avoid safety hazards, use only the power cord supplied with your unit. If a

r e p l a c e m e n t c o r d i s u s e d , m a k e c e r t a i n t h a t i t i s o f a s i m i l a r g a u g e . W e d o n o t

recommend using extension cords with this product. As with all electrical devices, do

not run power cords under rugs or carpets or place heavy objects on power cords.

• Damaged power cords should be replaced immediately with cords meeting factory

specications.

• Handle the AC power cord gently.

• When disconnecting the power cord from an AC outlet, always pull the plug; never

pull the cord.

• Do not try to open the device, may cause damages or shock hazard. and warranty

will be void.

• There are no user-serviceable components inside this product.

• If water enters the unit, or any metal object such as paper clip, wire or staple accidentally

falls inside the cabinet, disconnect the unit from the AC power source immediately and

consult an authorized warranty station.

• Always use a soft dry cloth to clean the equipment. Do not use solvents.

4

1. INSTALLATION

Place the unit on a rm and level surface. When placing the unit on a shelf, be

certain that the shelf and any mounting hardware can support the amplier’s

weight.

- Make certain that the proper space is provided both above and below the unit

for ventilation. If the amplier will be installed in a cabinet or other enclosed area,

make certain that there is sufcient air movement within the cabinet.

- Do not place the unit directly on a carpeted surface.

- Avoid installation in extremely hot or cold locations, in an area that is exposed

to direct sunlight or near heating equipment.

- Avoid moist or humid locations.

- Do not obstruct the ventilation slots on the top of the unit or place objects

directly over them. Remember, power ampliers generate heat, and the heatsink

ns and ventilation slots that form part of the cabinet are specially designed to

remove this heat.

- The shipping materials used to protect your new amplier were specially

designed to cushion it from shipping’ shock and vibration. We suggest that you

save the carton and packing materials for use in shipping if you move or if the

unit ever needs repair.

5

2. HIGHLIGHTS

The P.A. amplier has 210W max of power output and it includes a SD card

reader to play MP3 les.

It features three microphone inputs, one auxiliary input and non-amplied output

to connect other amplier or amplied speaker box.

The display shows the current track and elapsed time. What is more, the amplier

allows you to record from the input source to the SD card.

• MP3 Reader / Recorder

• Three microphone inputs, one auxiliary

• Independent volume control

• 70V output line

6

3. CONTROLS

FRONT PANEL

REAR PANEL

7

1. LCD screen

2. SD slot: Allow to connect a SD Memory Card with MP3 audio les.

3. PLAY/PAUSE: Plays or pauses SD tracks.

4. FR: Returns to previous tracks.

5. FF: Advances to next track.

6. VOL DOWN: Decreases the volume level from the SD player.

7. REC: Records on SD / USB whatever the amplier is reproducing.

8. POWER/ STOP: Press and hold to turn on or off SD / USB player and press

once to stop the current play.

9. VOL UP: Increases the volume level from the SD player.

10. REPEAT: Select repeat mode.

REP: to repeat in Random mode.

1: Repeat one track.

ALL: Repeat an all track.

11. Master: Master volume control.

12. Treble: Treble level control.

13. Bass: Bass level control.

3.1 Front panel

8

14. CD/AUX: Set the volume level of the auxiliary equipment connected to the

amplier.

15. MIC 3: Microphone 3 volume control.

16. MIC 2: Microphone 2 volume control.

17. MIC 1: Microphone 1 volume control.

18. MIC-3: Microphone 3 input.

19. MIC-2: Microphone 2 input.

20. MIC-1: Microphone 1 input.

21. Output signal indicator

22. Power LED indicator

23. ON/OFF switch

24. SD/USB: Select SD / USB device.

25. Gain: Insert a screwdriver to set the level gain of recording.

26. PEAK: It lights up when the volume of recording from the microphone is too

loud.

27. USB port: Here you can insert a USB stick

9

1. CA (115V~/230V~) switch

2. Ground

If the main contact doesn’t counts with a ground lead, this screw offers you the

possibility to ground the amplier’s metallic parts.

3. AC Input.

4. Fuse (T5V 250V) compartment

5. LINE OUT

Allow one to connect an external audio system.

6. CD/AUX

Allow one to connect an external audio system.

7. Low and High impedance output.

3.2 Rear panel

4. CONNECTIONS

1. Insert a Microphone to MIC1 input until 3

microphones (MIC2 input and MIC3 input).

2. In LINE OUT you can connect a recorder or

audio system.

-10- 10+10+ 10 0+ 10 0+ 10

TREBLEMASTER BASS CD/AUX MIC3

MIC3

0+ 10

MIC2

0+ 10

MIC1

POWER

AMP-210CD

0

10

RATED SUPPLY VOLTAGE:

120V-60Hz

10

3. For connect the speakers there are different ways for example:

- Two 8 Ω speakers in parallel to get an

impedance of 4ohms

- Two 8 Ω speakers in serial to get an impedance

of 16ohms

- Four 8 Ω speakers in serial/ parallel to

get an impedance of 8ohms

+

-

+

-

11

When you want connect more of four speakers you can use 25, 70 or 100volts

output from amplier.

You’ll need a line transformer.

Never touch stripped wires from amplier’s output, when they’re in use, may

cause serious damages or electrical shock.

Replace the protector cover once you have nished the connection process.

4. Connect the power cord to AC input and the opposite end to connect an

electrical contact.

12

1. Set the volume level to minimum.

2. Press On/Off button.

3. Power on the device that you want to use (CD player, microphones or an

external audio system).

4. Gradually, raise the volume level to an optimum level.

5. Set the treble and bass controls in accord to your preferences.

6. If you want to use the SD / USB player, press POWER button.

7. The LCD screen lights on.

8. Press SD/USB button to select audio source.

9. Insert SD card or USB stick into slot.

10. Press Play to start to play the SD / USB audio les.

11. Use FF and FR buttons to go to next or previous track

12. Select repeat mode using REPEAT.

16. When you don’t want to use the amplier, press On / Off switch.

5. HOW TO USE

13

Input: 120 V~ 60 Hz 380 W

Frequency response: 50 – 15 000 Hz

Impedance: 4, 8 and 16 Ω

Power output: 150 Wrms / 210 W max

Nominal consumption: 273.6 kWh/month

Stand-by power consumption: not applicable

6. SPECIFICATIONS

Product design and specications are subject to change, without notice.

14

WARRANTY

This Steren product is warranted under normal usage against defects in workmanship

and materials to the original purchaser for one year from the date of purchase.

CONDITIONS

1. This warranty card with all the required information, invoice, product box or

package, and product, must be presented when warranty service is required.

2. If the product is in the warranty time, the company will repair it free of charge.

3. The repairing time will not exceed 30 natural days, from the day the claim was

received.

4. Steren sell parts, components, consumables and accessories to customer, as well

as warranty service, at any of the addresses mentioned later.

THIS WARRANTY IS VOID IN THE NEXT CASES:

If the product has been damaged by an accident, acts of God, mishandling, leaky

batteries, failure to follow enclosed instructions, improper repair by unauthorized

personnel, improper safe keeping, among others.

a) The consumer can also claim the warranty service in the purchase establishment.

b) If you lose the warranty card, we can reissue it, if you show the invoice or purchase

ticket.

RETAILER INFORMATION

Name of the retailer

Address

Product

Brand

Part number

Serial number

Date of delivery

Product: 210 W P.A. amplier with SD card reader

Part number: AMP-210SD

Brand: Steren

In case your product fails

or have questions, please

contact your nearest dealer.

If you are in Mexico, please

call to our Call Center.

01 800 500 9000

Page is loading ...

Steren AMP-210SD Owner's manual

Steren AMP-210SD Owner's manual

in other languages

Related papers

Other documents