Fender Bassman 300-300 Pro (2002-2013) Owner's manual

Page is loading ...

Important Safety Instructions

This symbol warns the user of dangerous voltage levels

localized within the enclosure.

This symbol advises the user to read all accompanying

literature for safe operation of the unit.

∆ Read, retain, and follow all instructions. Heed all warnings.

∆ Only connect the power supply cord to an earth grounded AC

receptacle in accordance with the voltage and frequency ratings

listed under INPUT POWER on the rear panel of this product.

∆ WARNING: To prevent damage, fire or shock hazard, do not

expose this unit to rain or moisture.

∆ Unplug the power supply cord before cleaning the unit exterior

(use a damp cloth only). Wait until the unit is completely dry

before reconnecting it to power.

∆ Maintain at least 6 inches (15.25 cm)of unobstructed air space

behind the unit to allow for proper ventilation and cooling of the

unit.

∆ This product should be located away from heat sources such as

radiators, heat registers, or other products that produce heat.

∆ This product may be equipped with a polarized plug (one blade

wider than the other). This is a safety feature. If you are unable

to insert the plug into the outlet, contact an electrician to replace

your obsolete outlet. Do not defeat the safety purpose of this

plug.

∆ Protect the power supply cord from being pinched or abraded.

∆ This product should only be used with a cart or stand that is

recommended by the manufacturer.

∆ The power supply cord of this product should be unplugged from

the outlet when left unused for a long period of time, or during

electrical storms.

∆ This product should be serviced by qualified service personnel

when: the power supply cord or the plug has been damaged; or

objects have fallen, or liquid has been spilled onto the product;

or the product has been exposed to rain; or the product does not

appear to operate normally or exhibits a marked change in

performance; or the product has been dropped, or the enclosure

damaged.

∆ Do not drip nor splash liquids, nor place liquid filled containers on

the unit.

∆ CAUTION: No user serviceable parts inside, refer servicing to

qualified personnel only.

∆ Fender

®

amplifiers and loudspeaker systems are capable of

producing very high sound pressure levels which may cause

temporary or permanent hearing damage. Use care when

setting and adjusting volume levels during use.

∆ WARNING: The unit must only be connected to a safety agency

certified power source (adapter), approved for use and compliant

with applicable local and national regulatory safety requirements.

Instrucciones de Seguridad Importantes

Este símbolo advierte al usuario que en el interior de la

carcasa hay niveles peligrosos de voltaje.

Este símbolo advierte al usuario que lea toda la

documentación adjunta para utilizar la unidad con

seguridad.

∆ Lea las atentamente instrucciones y sígalas al pie de la letra.

Tenga en cuenta todas las instrucciones.

∆ Conecte únicamente el cable de alimentación eléctrica a una

toma de CA de acuerdo con las especificaciones de voltaje y

frecuencia que se indican en la potencia de entrada INPUT

POWER del panel posterior de este producto.

∆ ADVERTENCIA: Para evitar daños, incendios y descargas

eléctricas, no exponga esta unidad a la lluvia ni a la humedad.

∆ Antes de limpiar el exterior de la unidad, desconecte el cable de

alimentación (utilícese únicamente un paño húmedo). Deje que

la unidad se seque completamente antes de volver a conectarla

a la corriente.

∆ Para una ventilación y refrigeración adecuadas, deje un espacio

mínimo de 15.25 cm detrás de la unidad.

∆ Este producto deberá estar situado lejos de fuentes de calor

tales como radiadores, registros de calefacción u otros

productos que generen calor.

∆ Es posible que este producto esté equipado con un enchufe

polarizado (un blade más ancho que el otro). Esta es una

función de seguridad. Si no puede introducir el enchufe dentro

de la toma de corriente, póngase en contacto con un electricista

para que la cambie ya que podría estar anticuada. No anule el

propósito de seguridad de este enchufe.

∆ Tenga cuidado de que el cable de alimentación no se pinche ni

se erosione.

∆ Este producto sólo se debe utilizar con el soporte recomendado

por el fabricante.

∆ El cable de alimentación de este producto deberá estar

desconectado de la toma de corriente cuando no se vaya a

utilizar durante un período de tiempo largo o en caso de

tormenta eléctrica.

∆ Este producto deberá ser reparado por personal cualificado si:

el cable de alimentación o el enchufe están dañados, ha caído

algún objeto o se ha derramado líquido encima, el producto ha

estado expuesto a la lluvia, no funciona normalmente o muestra

signos de cambio en el rendimiento, ha sufrido algún golpe o la

caja esta dañada.

∆ Evite que goteen o salpiquen líquidos y no coloque recipientes

con líquidos sobre la unidad.

∆ PRECAUCIÓN: Contiene piezas cuyo mantenimiento no lo

puede realizar el usuario, sino sólo personal cualificado.

∆ Los amplificadores y altavoces Fender

®

pueden producir niveles

de presión acústica muy elevados, que pueden provocar daños

temporales o permanenetes en el oído. Utilice la precaución al

ajustar el volumen nivela.

∆ ADVERTENCIA: La unidad sólo se podrá conectar a una fuente

de alimentación certificada por un organismo de seguridad

(adaptador) cuyo uso esté autorizado y que cumpla los

requisitos de seguridad aplicables a nivel local y nacional.

Page is loading ...

A. INPUT - Plug your electric bass guitar in here.

B. -6 dB PAD - Sensitivity / gain switch for the input signal.

Button IN provides a -6dB attenuation useful for electric

bass guitars with high output levels, such as basses with

active pickups.

C. CH 1 VOLUME - Adjusts the loudness of channel 1.

D. CH 1 LED - Illuminates when channel 1 is active.

E. CH 2 GAIN - Adjusts the channel 2 gain/distortion level.

F. CH 1 / 2 MIX LED - Illuminates when the ch select

button is IN indicating the Ch. 1 / Ch. 2 mix is active.

G. CH 2 VOLUME - Adjusts the loudness of channel 2.

H. CH SELECT - When this button is IN, both channel 1

and channel 2 are active. This button is used in

conjunction with the CH. 1 / 2 MIX knob. Using the

footswitch overrides this switch.

I. CH 1 / 2 MIX - Mixes the channel 1 and channel 2 output

levels. At “1”, only channel 1 is in the output mix. At “10”,

only channel 2 is in the output mix. By rotating the knob, an

optimum mix of both channels may be obtained.

J. LOW - Adjusts the low frequency level of both channels.

In its center notched position, the equalization is “flat” with

no modification.

K. HIGH - Adjusts the high frequency level of both

channels. In its center notched position, the equalization is

“flat” with no modification.

L. DEEP - Low frequency boost when this button is IN.

M. BRIGHT - High frequency boost when this button is IN.

N. MID NOTCH - Reduces the mid-frequency tones, giving

the amp a “punchy” sound when this button is IN.

O. GRAPHIC - Activates the graphic equalizer when this

button is IN. Using the footswitch overrides this switch.

P. LINE OUT - This switch is used in conjunction with the

line out jacks on the rear of the 300. When this button is

IN, the signal sent from the 300 includes frequency

shaping, channel switching and compression. The line out

signal does NOT include any effects which may have been

added via the effects loop. When the button is OUT the

signal is passed through the 300 without any tone shaping

or enhancement.

Q. GRAPHIC EQ - The 10 band-pass / band-reject filters

are spaced at octave intervals. Move each slider up to

boost or down to cut the level of each indicated frequency.

The EQ Trim slider will boost or cut the signal level through

the graphic EQ with the centered notched position having

no affect on the level.

R. GRAPHIC EQ LED - Illuminates when the graphic EQ is

active.

S. LOW COMP - Adjusts the compression ratio below

400Hz. Clockwise rotation increases the compression

ratio.

T. COMP - When this button is IN the compressors are

active. Using the footswitch overrides this switch.

U. HIGH COMP - Adjusts the compression ratio above

400Hz. Clockwise rotation increases the compression

ratio.

V. COMP LED - Illuminates when the compressor is active.

W. COMP EQ BAL - Mixes the low and high compressor

outputs. When the knob is at “1”, only the low compressor

is in the output mix. When the knob is at “10”, only the high

compressor is in the output mix. By rotating the knob, an

optimum mix of both compressors can be obtained.

X. INPUT LEVEL LED - Always indicates signal level.

Glows green above the compressor threshold. Glows red

above the pre-amp clipping/distortion threshold.

Y. COMP GAIN TRIM - This knob adjusts gain to

compensate for any level imbalance when the compression

circuitry has been engaged.

Z. TUNER ONLY - While this button is IN all outputs from

the amplifier are muted except to the tuner jack. Useful for

quick and silent bass tuning.

AA. MASTER VOLUME - Adjusts the overall volume level

of the 300 in conjunction with the gain controls of the active

channel(s).

BB. POWER LED - Illuminates when the 300 is ON and

receiving power.

CC. STANDBY - When the power switch and this switch

are ON, your 300 is ready to perform. In the standby

position, power is supplied only to the tube filaments and

sound will NOT come out of the amp. Using the standby

switch during short breaks eliminates tube warm-up time

and will increase tube life.

6

BB

aa

ss

mm

aa

nn

®®

33

00

Congratulations on your purchase of a Bassman

®

300 bass

amplifier. Among its many features:

•300 Watts of output power into 2Ω, 4Ω, or 8Ω (selectable)

•Two channels for both clean and distortion outputs

•Vacuum tube pre-amplifier and power-amplifier design

•10-band graphic equalizer and split band compressor

•Footswitch with equalizer, compressor and channel

switching

•Low-noise differential effects loop

•Tuner out jack for pass-through tuning

•XLR and 1/4 inch line out jacks and a pass-through jack for

output to another amplifier or to a mixing console

•All steel chassis for enduring reliability

A. POWER - Turns the AC power ON and OFF.

B. LINE CORD - The 300 is equipped with a grounding

type IEC supply cord and must be connected to a

grounded AC receptacle in accordance with the voltage

and frequency ratings as shown on the rear panel of the

300 amplifier.

C. FUSE - In the AC supply of the amplifier the fuse will

help to protect the amplifier from an electrical fault.

Replace a failed fuse only with one of the same type and

rating (See Specification page). If the amplifier

repeatedly blows fuses, take the amplifier to an

authorized Fender® service center.

D. SEND - This 1/4 inch, unbalanced, differential, TS

(tip-sleeve) output jack is designed for output to an

external signal processing device.

E. RETURN - This 1/4 inch, balanced, TRS (tip-ring-

sleeve) input jack is designed to accept signal from an

external signal processing device.

F. POWER AMP PASS THROUGH - This 1/4 inch,

unbalanced, differential, TS (tip-sleeve) output jack is

designed to send a preamp line-level signal from your

“main” 300 amplifier to an “add-on” 300 amplifier for

additional output. Use a standard patch cord (1/4”

plugs) to connect this jack to the return effects loop jack

of the “add-on” 300 forming a “daisy-chain.”

G. FOOTSWITCH - Plug-in connection for the

footswitch (P/N 053895). The footswitch enables remote

switching of the graphic equalizer, compressors and

channels. These switching functions are disabled on the

front panel when this jack is used. NOTE: Connect the

footswitch with an unshielded speaker type cord rather

than a coaxial guitar cord for best results.

H. LINE OUT - Transformer balanced, line-level outputs.

Use either the XLR male or 1/4 inch, TRS (tip-ring-

sleeve) jacks to feed the 300’s signal to an external

power amplifier or sound console. The signal from either

of these jacks includes all the tone shaping done by the

300. This includes a bass speaker emulation circuit.

I. TUNER OUT - This 1/4 inch, unbalanced, TS output

jack is designed for output to your tuning device (not

included).

J. SPEAKER IMPEDANCE - Select a setting that

matches the total impedance load of the loudspeaker

enclosure(s) connected to the 300. Failure to do so may

result in damage to the 300 amplifier. See the chart on

this page for a listing of the impedance loads of some

common speaker cabinet combinations.

K. MAIN SPEAKER JACK - This is the main speaker

plug-in connection. There must ALWAYS be a speaker

load connected to this jack when the amplifier is ON to

prevent the possibility of damage to the unit. ALWAYS

connect or disconnect speakers to your 300 with the

power off and the power cord unplugged from the wall.

L. EXTERNAL SPEAKER JACK - Plug-in connection for

an additional speaker enclosure. This jack is wired in

parallel with the main speaker jack and must only be

used when another speaker is also connected to the

main speaker jack.

7

RR

ee

aa

rr

PP

aa

nn

ee

ll

CC

oo

nn

tt

rr

oo

ll

ss

Speaker Cabinets

1 8Ω Cabinet

2 8Ω Cabinets

1 4Ω Cabinet

2 4Ω Cabinets

4Ω

LoadΩ

2Ω

4Ω

8Ω

1. BIAS - Used with the bias test points to set the output

tube bias.

2. & 3. BIAS 100mV - Test points used to measure output

tube bias with a digital voltmeter.

3. & 4. BALANCE 0V - Test points used to measure output

tube balance with a digital voltmeter.

5. BALANCE - Used with the balance test points to set the

balance between the power amp tube sections.

Output Tube Bias & Balance Adjustment Instructions:

1. Turn on your 300 and let it warm up for at least two

minutes with the STANDBY switch in the ON position. Make

sure the amplifier is properly connected to a speaker.

2. Remove the bias controls cover box.

3. With a digital voltmeter set to its most sensitive DC

voltage scale, measure the voltage between the bias 100mV

test points (2 & 3) and with a screwdriver, turn the the bias

adjustment for a reading of .1 VDC (100 mVDC).

4. Next, connect the digital voltmeter to the balance 0V test

points (3 & 4) and turn the balance for a reading of 0 VDC.

5. Replace the bias controls cover box.

Notes:

•Make bias and balance adjustments ONLY when

necessary. If you are unsure about these settings take your

amp to the nearest authorized Fender® Service Center.

•Always set bias first, then set balance.

•If the output tubes can not be biased to at least 80mVDC,

replace the 6550C output tubes.

•If the output tubes can not be balanced, check the bias

setting and/or replace the 6550C output tubes.

•The tube trouble LEDs are NOT indicators of worn tubes.

If your tubes are worn and sound weak the LEDs will still

glow green. The trouble LEDs turn Red only after tube

failure has already occurred. DO NOT WAIT FOR TUBE

FAILURE TO REPLACE TUBES. (See Tube Testing &

Replacement section).

6. TUBE TROUBLE - These LEDs indicate tube failure or

trouble at their corresponding locations. When the LED

glows green, the tubes are operating. When the LED glows

red, a tube failure has blown the fuse at the corresponding

fuse location on the top surface of the chassis. NOTE: It is

normal for the LEDs to glow RED when the amp is in standby

mode. If a fuse blows, replace it only with one of the same

type and rating. If the amplifier repeatedly blows fuses, it

should be taken to an authorized Fender® service center.

8

TT

uu

bb

ee

TT

rr

oo

uu

bb

ll

ee

LL

EE

DD

ss

TT

uu

bb

ee

TT

ee

ss

tt

ii

nn

gg

&&

RR

ee

pp

ll

aa

cc

ee

mm

ee

nn

tt

TT

uu

bb

ee

BB

ii

aa

ss

aa

nn

dd

BB

aa

ll

aa

nn

cc

ee

AA

dd

jj

uu

ss

tt

mm

ee

nn

tt

Tube life varies depending upon playing style and

application. Power tubes have a shorter life than pre-amp

tubes which can last for many years. For continued

optimum performance from your amplifier, the tubes should

ONLY be replaced with the same type tubes as specified

above.

IMPORTANT: ALWAYS unplug the amplifier before

changing tubes and remember: THE TUBES GET HOT!

A simple way to check if the tubes are worn is to replace the

set in your amp with your spare set and listen for

improvement. (You carry a spare set of tubes and fuses,

don't you?)

•First, replace the OUTPUT tubes with new tubes; re-bias

and listen (bias/balance instructions are on the next page).

•Next, re-insert the original output tubes and re-bias.

Replace the PRE-AMP tubes with new tubes and listen.

•Finally, try replacing both the output (re-bias) and PRE-

AMP tubes with new tubes and listen.

If there is a marked improvement in the tone of your amp at

any point in this procedure, leave the new tubes in your amp

and purchase another spare set.

The 300's tube compliment consists of:

•One 12AT7A Tube (part #023531), (tube location V4)

•Three 12AX7WA Tubes (part #013341), (tube locations V1

thru V3.

•Six 6550C Tubes (part #048489), (tube locations V5 thru V10).

TYPE: PR 347

PART NUMBER: 021-3302-010 (120V, 60Hz) US 021-3312-010 (110V, 60Hz) TW

021-3332-010 (240V, 50Hz) AUS 021-3342-010 (230V, 50Hz) UK

021-3352-010 (220V, 50Hz) ARG 021-3362-010 (230V, 50Hz) EUR

021-3372-010 (100V, 50Hz) JPN 021-3392-010 (220V, 60Hz) ROK

POWER REQUIREMENTS: 900W

PREAMP SECTION

INPUT IMPEDANCE: 470kΩ

FULL POWER SENSITIVITY : 12mV

TONE CONTROLS: Treble: +/-15 dB @ 6kHz

Bass: +/-15 dB @ 40Hz

GRAPHIC EQUALIZER: +/-12 dB @ 31.5Hz, 63Hz, 125Hz, 250Hz, 500Hz, 1kHz, 2kHz, 4kHz, 8kHz, 16kHz.

MID NOTCH: -20 dB @ 700Hz

LOW BOOST: +10 dB @ 40Hz

HIGH BOOST: +10 dB @ 6kHz

COMPRESSOR:

CROSSOVER: 400Hz

RATIO: 1:1 Min to 4:1 Max

LINE OUT LEVEL: +6dB referenced to input (pre), 0dBV (post).

(transformer balanced)

POWER AMPLIFIER SECTION

INPUT IMPEDANCE: 20kΩ

POWER OUTPUT: 300W R.M.S. into 2, 4, or 8Ω @ <3% T.H.D.

SENSITIVITY : 1V R.M.S. (0dBv)

SPEAKER COMPLEMENT: Designed for use with the Bassman 410H Pro or Bassman 215

Bass Loudspeaker Enclosures

DIMENSIONS: Height: 10.1 in (25.7 cm)

Width: 25.5 in (64.8 cm)

Depth: 15.6 in (40 cm)

WEIGHT: 75 lb 34 kg

Product specifications are subject to change without notice.

9

SS

pp

ee

cc

ii

ff

ii

cc

aa

tt

ii

oo

nn

ss

Page is loading ...

TIPO: PR 347

NÚMERO DE PIEZA: 021-3302-010 (120V, 60Hz) US. 021-3312-010 (110V, 60Hz) TW

021-3332-010 (240V, 50Hz) AUS 021-3342-010 (230V, 50Hz) RU

021-3352-010 (220V, 50Hz) ARG 021-3362-010 (230V, 50Hz) EUR

021-3372-010 (100V, 50Hz) JPN 021-3392-010 (220V, 60Hz) ROK

REQUISITOS DE CORRIENTE: 900 W

SECCIÓN DEL PREAMPLIFICADOR

IMPEDANCIA DE ENTRADA: 470 kΩ

SENSIBILIDAD A TODA POTENCIA: 12mV

CONTROLES DE TONO: Agudos: +/-15 dB @ 6 kHz

Graves: +/-15 dB @ 40 kHz

ECUALIZADOR GRÁFICO: +/-12 dB @ 31,5 Hz, 63 Hz, 125 Hz, 250 Hz, 500 Hz, 1 kHz, 2 kHz, 4 kHz, 8 kHz, 16 kHz.

BOTÓN DE MEDIOS: -20 dB @ 700 Hz

AMPLIFICACIÓN BAJA: +10 dB @ 40 Hz

AMPLIFICACIÓN ALTA: +10 dB @ 6 Hz

COMPRESOR:

FRECUENCIA DE TRANSICIÓN: 400 Hz

RELACIÓN: 1:1 mín. a 4:1 máx.

NIVEL DE SALIDA: +6 dB respecto a la entrada (antes), 0 dBV (después).

(transformador con balance)

SECCIÓN DEL AMPLIFICADOR PRINCIPAL

IMPEDANCIA DE ENTRADA: 20 kΩ

POTENCIA DE SALIDA: 300 W R.M.S. a 2, 4 o 8Ω @ <3% T.H.D.

SENSIBILIDAD : 1V R.M.S. (0 dBv)

COMPLEMENTO DE ALTAVOZ: Diseñado para su utilización con cajas acústicas para

bajos Bassman 410H Pro o Bassman 215

DIMENSIONES: Height: 10.1 in. (25.7 cm)

Ancho: 25.5 in. (64.8 cm)

Fondo: 15.6 in. (40 cm)

PESO: 75 lbs. 34 kg

Las especificaciones del producto están sujetas a cambios sin previo aviso.

EE

ss

pp

ee

cc

ii

ff

ii

cc

aa

cc

ii

oo

nn

ee

ss

13

Page is loading ...

TIPO: PR 347

NUMERO DI PARTE: 021-3302-010 (120V, 60Hz) US. 021-3312-010 (110V, 60Hz) TW

021-3332-010 (240V, 50Hz) AUS 021-3342-010 (230V, 50Hz) RU

021-3352-010 (220V, 50Hz) ARG 021-3362-010 (230V, 50Hz) EUR

021-3372-010 (100V, 50Hz) JPN 021-3392-010 (220V, 60Hz) ROK

REQUISITI DI ALIMENTAZIONE: 900W

SEZIONE PREAMP

IMPEDENZA DI INGRESSO: 470kΩ

SENSIBILITÀ PER PIENA POTENZA: 12mV

CONTROLLI DI TONO: Alti: +/-15 dB @ 6kHz

Bassi: +/-15 dB @ 40Hz

EQUALIZZATORE GRAFICO: +/-12 dB @ 31,5Hz, 63Hz, 125Hz, 250Hz, 500Hz, 1kHz, 2kHz, 4kHz, 8kHz, 16kHz.

MID NOTCH: -20 dB @ 700Hz

LOW BOOST: +10 dB @ 40Hz

HIGH BOOST: +10 dB @ 6kHz

COMPRESSORE:

CROSSOVER: 400Hz

RAPPORTO: da 1:1 Min a 4:1 Max

LIVELLO USCITA DI LINEA: +6dB riferito all’ingresso (pre), 0dBV (post).

(bilanciato da trasformatore)

SEZIONE AMPLIFICATORE DI POTENZA

IMPEDENZA DI INGRESSO: 20kΩ

POTENZA: 300W valore quadratico medio per 2, 4 o 8Ω al 3% di

distorsione armonica totale

SENSIBILITÀ : 1V valore quadratico medio (0dBv)

COMPLEMENTO SPEAKER: Progettato per l’uso con Enclosure altoparlanti per basso

Bassman 410H o Bassman 215

DIMENSIONI: Altezza: 10.1 in. (25.7 cm)

Larghezza: 25.5 in. (64.8 cm)

Profondità: 15.6 in. (40 cm)

PESO: 75 lbs. 34 kg

Le specifiche dei prodotti sono soggette a modifica senza preavviso.

SS

pp

ee

cc

ii

ff

ii

cc

hh

ee

21

Page is loading ...

A PRODUCT OF:

FENDER® MUSICAL INSTRUMENTS CORP

CORONA, CA USA

Fender® and Bassman® are registered trademarks of FMIC

P/N 057731 REV A

Fender Bassman 300-300 Pro (2002-2013) Owner's manual

This manual is also suitable for

Fender Bassman 300-300 Pro (2002-2013) Owner's manual

in other languages

Related papers

Other documents