Presenza QR025 Installation guide

Brand: Presenza

Model: QR025

Category: Cooker hoods

Type: Installation guide

This manual is also suitable for

QR025 654OVSN016STS

Presenza QR025 654OVSN016STS

The Presenza QR025 654OVSN016STS is a powerful under-cabinet range hood designed to effectively remove smoke, odors, and grease from your kitchen while you cook. With a sleek and modern design, it seamlessly integrates into your kitchen décor and provides ample lighting for your cooking surface.

Key Features:

Efficient Ventilation: The QR025 boasts a high-performance motor that delivers up to 400 CFM of airflow, ensuring efficient removal of cooking fumes and odors.
Adjustable Fan Speed: Choose from three fan speeds to customize the airflow according to your cooking needs, from simmering to searing.

Presenza QR025 654OVSN016STS

Key Features:

Efficient Ventilation: The QR025 boasts a high-performance motor that delivers up to 400 CFM of airflow, ensuring efficient removal of cooking fumes and odors.
Adjustable Fan Speed: Choose from three fan speeds to customize the airflow according to your cooking needs, from simmering to searing.

UNDER CABINET

RANGE HOOD

INSTALLATION GUIDE

AND USER MANUAL

Model No. QR025

654OVSN016STS

Table of Contents

Table of Contents ............................2

Safety Information ............................2

Warranty

One Year Limited Warranty ...........................4

Warranty Claim Procedure ...........................4

Pre-Installation

Tools/Materials Required ............................5

Package Contents .................................6

Hardware Included .................................6

Planning Installation ...............................7

Installation ................................ 10

Operation ................................. 13

Maintenance

Replacing Filters .................................14

Replacing Lights .................................14

Care and Cleaning

Range Hood .....................................15

Filters ..........................................15

Troubleshooting ............................ 16

Specifications

Wiring Diagram ..................................17

External Range Hood Diagram .......................18

Service Parts .............................. 19

Safety Information

READ AND SAVE THESE INSTRUCTIONS

Warning - To reduce the risk of fire, electric shock, or injury to

persons, observe the following:

1. Use this unit only in the manner intended by the manufacturer. If

you have any questions, contact the manufacturer.

2. Before servicing or cleaning unit, switch power off at service

panel and lock service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by qualied

person(s) in accordance with all applicable codes and standards,

including re-rated construction.

4. Sufcient air is needed for proper combustion and exhausting

of gases through the ue (chimney) of fuel burning equipment

to prevent back drafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into a wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

DANGER: Turn off the power circuit breaker or the power

switch on the junction box before installing or servicing

this unit. Touching circuitry inside the range hood while it is

energized will result in death or serious injury.

DANGER: All electrical wiring must be properly installed,

insulated, and grounded. Improper insulation and grounding

will result in deadly electrical shock.

DANGER: If installing this unit over a gas range, turn off

the gas at the source before installing or servicing this unit.

WARNING: Attempting to install or service this unit

when you do not have the necessary technical or electrical

background could result in personal injury.

WARNING: The unit has sharp edges. Always wear safety

gloves during installation, cleaning, or servicing.

WARNING: Always leave safety grills and lters in place.

Without these components, operating fans could catch on to

hair, ngers, or loose clothing.

WARNING: Stay clear of the rotating fan when the motor

is running.

WARNING: Keep this appliance clean and free of grease

and residue build-up at all times to prevent res.

CAUTION: This device is for general ventilating use only.

Do not use to exhaust hazardous or explosive materials and

vapors.

3 CONGLOMKB.COM

Please contact customer.service@conglomkb.com or 1-877-333-0098 for further assistance.

Safety Information (continued)

COOKING SAFETY INFORMATION

1. Never leave the range hood unattended when in use.

2. Never cook over open ames under the range hood.

3. Always turn the range hood on when cooking at high heat

or when cooking aming foods.

4. If you choose to hang the range hood as below (Fig. 1) distance

(D) from the cooktop surface, use extra caution as the surface

of range hood may be extremely hot to the touch. For this unit,

(D in Fig. 1) is 458 mm - 710 mm (18 in - 28 in). If you choose

an 18 in installation, the temperature of the unit surface will

be high if the unit is operated under high power cooking for a

certain amount of time.

5. Use caution when cooking with oil or with deep-fryers.

Overheating may cause oil to reach its ash point and ignite.

Used oil will ignite at lower temperatures than fresh oil. Heat

oils slowly on low to medium setting.

6. Avoid boil overs, as they may cause smoking and greasy

spillovers that could ignite.

7. To prevent burns or res, always use cookware appropriate to

the size of the heating element that you are using.

8. In event of a cooking re, observe the following:

- Be careful to avoid burns.

- Smother ames with a close-tting lid, cookie sheet, or

metal tray, then turn off the burner. If the ames do not go

out immediately, evacuate and call the re department.

- Never pick up a aming pan.

- Do not use water, including wet dishcloths or towels, as you

could cause a steam explosion.

- Use an extinguisher only if: (a) you have a class ABC

extinguisher and you know how to operate it, (b) the re is

small and contained in the area where it started, (c) the re

department is being called, and (d) you can ght the re with

your back to the exit.

CLEANING SAFETY INFORMATION

1. The fan and lters must be cleaned periodically and kept free

from accumulation of cooking residue. Old and worn lters must

be replaced immediately.

2. Never disassemble parts to clean. Parts should be disassembled

by qualied persons only.

WARNING: To reduce the risk of re, use only metal duct

work. Never use plastic duct work.

WARNING: To reduce the risk of re or electric shock, do

not use this range hood with with any external solid state

speed control device.

CAUTION: For general ventilation use only. Do not use the

range hood fans to exhaust hazardous or explosive vapours.

CAUTION: Never dispose of cigarette ashes, ignitable

substances, or any foreign objects in fans.

CAUTION: At least two people are needed to move and

safely install the unit. Failure to properly lift the range hood

could result in product damage or personal injury.

Fig. 1

Warranty

ONE YEAR LIMITED WARRANTY

A thorough inspection must be made before installation and any damage must be promptly reported. We will not be liable for failures or

damage that could have been discovered or avoided by proper inspection and testing prior to installation.

Conglom Kitchen & Bath warrants this product to be free from defects in materials or workmanship for one (1) year from the date of purchase.

Proof of purchase (original sales receipt) from the original consumer purchaser must be made available to Conglom Kitchen & Bath for all

warranty claims.

This warranty is non-transferable and shall be voided if the unit is removed from its initial installation or if it is not installed following the

manufacturer’s instructions. It does not apply in the event of product damage due to the use of other than genuine Conglom Kitchen &

Bath replacement parts, (Replacement parts may be obtained by e-mail at customer[email protected] or by calling 1-877-333-0098

between 8:30 am - 5:00 pm EST) installation error, abuse, misuse or improper care and maintenance (whether performed by a plumber,

contractor, service provider or member of the purchaser’s household). The warranty excludes damage due to aggressive air or water

conditions, harsh or abrasive cleaners and/or materials.

Under no circumstance shall we be held liable for personal injury or property damage resulting from improper installation or use of this

product. We will not be held liable for inconvenience caused by loss of use of this product, costs incurred for labour or materials, removal

and installation of replacement units, or any other incidental or consequential damages. Costs relating to obtaining access for repair or

replacement are the responsibility of the user.

Our obligation shall be limited to the repair or replacement of a unit (at our discretion) that may prove, by our sole examination, to be defective

under normal use and service during the warranty period.

Any failure of this product that is not traceable to a defect in material or workmanship is not covered by this warranty. These non-warrantable

items include, but are not limited to:

- Improper installation not in accordance with manufacturer’s instructions.

- Dents and/or scratches incurred during shipping, handling, or installation.

- Change in colour or nish due to chemical usage.

- Damage caused by failure to follow care and cleaning guidelines, including damage caused by the use of abrasive cleaners.

- Alterations made to the unit by the purchaser or installer.

- Damage caused by accidental impact, re, ood, freezing, and normal wear.

- Bends and warping caused by forced connections, over-tightened ttings, and inadequate support during installation.

- Any defects or damage to light bulbs.

This warranty does not extend to commercial and institutional installation or use.

WARRANTY CLAIM PROCEDURE

If a claimable defect occurs or replacement parts are needed, please contact our customer service team at customer.service@conglomkb.

com or 1-877-333-0098 (Service available in English and French, Monday - Friday from 8:30 am - 5 pm, EST).

Before you make your call, please ensure that you have:

- Model number or description.

- Proof of sale.

- Details regarding the defect and/or part number.

- Name(s) and address(es) of the owner and/or installer.

5 CONGLOMKB.COM

Please contact customer.service@conglomkb.com or 1-877-333-0098 for further assistance.

Pre-Installation

TOOLS/MATERIALS REQUIRED (NOT SUPPLIED)

Measuring tape Level Utility knife

Pencil Tape

Adjustable

wrench

Phillips screwdriver

Flathead

screwdriver

Needle nose

pliers

Hammer Electric drill Safety goggles

Safety gloves

Pre-Installation (continued)

PACKAGE CONTENTS

Part Description Quantity

A Range hood 1

B Charcoal lter (located inside the hood) 1

C Damper (located on the hood) 1

HARDWARE INCLUDED

NOTE:

Parts not shown to actual size.

AA BB

Part Description Quantity

AA Long tapping screw - (M5 mm x 30 mm) 4

BB Short tapping screw - (M4 mm x 8 mm) 2

7 CONGLOMKB.COM

Please contact customer.service@conglomkb.com or 1-877-333-0098 for further assistance.

Pre-Installation (continued)

PLANNING INSTALLATION

Number of people required: 2 or more

Carefully check the range hood for damage and for missing parts

prior to installation. If there is any damage or if you are missing parts,

do not proceed with the installation. Report damage and missing

parts immediately. Do not dispose of packaging before you are

satised with your new range hood.

1. Before installation, measure all distances to ensure the proper

position of the range hood (A).

- The distance (1) from the cooking surface to the range hood

must be at least 458 mm (18 in). For the best performance,

do not install the range hood more than 710 mm (28 in)

above the cooking surface.

- Dimension (2) should be at least 762 mm (30 in). The range

hood should be approximately the same size as the cook top.

2. If the bottom of the cabinet (3) above the location where the range

hood is to be installed is recessed, attach appropriately sized wood

ller strips (4) on each side using wood screws.

3. Screws are provided to secure the range hood to most types of

cabinets, but consult a qualied installer to verify that the supplied

screws are suitable for your cabinets.

4. Put a thick, protective covering over your counter, cooktop, or

range to protect it from damage and dirt during installation.

Remove any hazardous objects around the area.

WARNING: Always wear safety goggles and gloves during

installation.

3 4

VENTING OPTIONS:

a. Determine if your existing venting system is top venting or back venting, and ensure that the openings in the cabinet or wall for the

damper and for power access are in appropriate locations and are of appropriate sizes, as per Fig. 3 if it is top vent or Fig. 4 if it is

back vent.

b. If this is a new installation, choose the venting method that suits your needs. Cut out openings for the damper and for power access

in the cabinet bottom or exterior wall, depending on the direction of venting chosen.

Fig.3 Fig.4

260

10-1/4”

260

10-1/4”

Fig. 2

Pre-Installation (continued)

FOLLOW THESE GUIDELINES WHEN INSTALLING DUCT WORK:

- Your venting system must vent to the outdoors either horizontally through the back wall (13) or vertically through the roof (14)

(refer to Fig. 5/Fig. 6/Fig. 7).

- Use round metal duct work with a uniform diameter of 152 mm (6 in). The total duct run in the venting system should be not more

than 10.7 m (35 ft).

- Calculate the total effective length of the duct work by adding the equivalent lengths in the table shown (Fig. 9). For each tting

used add the length of the equivalent straight duct used in the system.

- Fasten all connections between pieces of duct with sheet metal screws and tape all joints with certied duct tape.

- If you must turn the path of the duct work using elbows, keep the number of elbows to a minimum for effective performance and

use no more than three 90° elbows. Ensure that there is a minimum of 458 mm (18 in) of straight vent between each elbow. Elbow

as far away from the range hood’s exhaust opening as possible.

- Cap the exterior of the duct with a wall cap (15) or roof cap (16). Never use 102 mm (4 in) laundry-type wall caps. Use caulking to

seal exterior wall or roof opening around the cap.

- The venting system must have a damper. If the roof or wall cap has a damper, do not use the damper supplied with the range hood.

Horizontal Wall Venting

Fig.5

Vertical Roof Venting

Fig.7

Horizontal Wall Venting

Fig.6

For inside venting system (air does not exhaust to outdoors) (Fig. 8):

Please refer to the Installation section. The cover on the top plate will be removed and air will be exhausted through the charcoal lter and

out from 17.

Fig. 9

Equivalent Length Chart

Type of duct Length added

45° Elbow 0.91 m (3 ft)

90° Elbow 1.52 m (5 ft)

90° Flat elbow 3.66 m (12 ft)

2.74 m (9 ft) Straight duct 2.74 m (9 ft)

Wall cap 0 m (0 ft)

Fig. 8

9 CONGLOMKB.COM

Please contact customer.service@conglomkb.com or 1-877-333-0098 for further assistance.

Pre-Installation (continued)

WIRING CONNECTION REQUIREMENTS

Installation work and electrical wiring must be done by a qualied

person(s) in accordance with all applicable codes and standards,

including re-rated construction.

OBSERVE ALL GOVERNING CODES AND ORDINANCES WARNINGS

- Electrical grounding is required for this range hood. Check with

a qualied electrician if you are not sure whether the range

hood is properly grounded.

- Failure to follow electrical requirements may result in a re.

- A fuse in the neutral or grounding circuit could result in

electrical shock.

- If the hot/cold water pipe is interrupted by plastic nonmetallic

gaskets or other materials, DO NOT use for grounding.

- DO NOT GROUND TO A GAS PIPE.

IMPORTANT: It is the customer’s responsibility to contact a qualied

electrical installer and assure that the electrical installation is adequate

and complies with the National Electrical Code, or CSA standards, as

well as all local codes and ordinances.

1. Save installation instructions for electrical inspector’s use.

2. If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine if the

ground path is adequate.

3. DO NOT use an extension cord or adapter plug with this

appliance.

4. The range hood must be connected with copper wire only.

5. The range hood should be connected directly to the junction (or

circuit breaker) box through exible, armoured or nonmetallic

sheathed copper cable. Allow some slack in the cable so the

appliance can be moved if servicing is ever necessary.

6. A UL listed or CSA approved conduit connector must be provided

at each end of the power supply cable (at the range hood and at

the junction box).

7. When making the electrical connection, cut a 3.2 cm (1-1/4 in hole

in the wall. A hole cut through wood must be sanded until

smooth. A hole through metal must have a grommet.

8. When cutting or drilling into the wall or ceilling, do not damage

electrical wiring and other hidden utilities.

9. Wire size must conform to all local codes and ordinances. The

latest edition requirements of the National Electrical Code ANSI/

NFPA 70, or the latest edition CSA Standards C22.1-94, Canadian

Electrical Code Part 1 and C22.2 No. 0-M91.

DANGER: Risk of electrical shock. This range hood must

be properly grounded.

DANGER: Turn off the power circuit breaker or the

power switch on the junction box before installing this

unit. Touching circuitry inside the range hood while it is

energized will result in death or serious injury.

DANGER: All electrical wiring must be properly installed,

insulated, and grounded. Improper insulation and grounding

will result in deadly electrical shock.

NOTE:

Temporarily wire the range hood to test it for proper operation. If

the range hood does not operate correctly, do not proceed with the

installation.

- Use the power supply cable to connect the range hood

(A) directly to the junction box or circuit breaker box.

Use a exible, armoured, or nonmetallic sheathed

copper cable only. Never use an extension cord or

adapter plug.

- Connect a UL-listed or CSA-approved conduit

connector to each end of the power supply cable (at

the range hood and at the junction box). Connect the

three colored wires (3) from the range hood (A) to the

corresponding wires (4) from the electrical source:

black to black (live), white to white (neutral), and

green/yellow to green/yellow (ground). Use either the

top hole (1) or the back hole (2) of the range hood

depending on your installation type.

- Turn the power on, and ensure that the lights and the

fan are operating correctly.

- Once you have tested the electrical connection,

disconnect the power supply cable and wires from the

electrical source before proceeding with the rest of the

installation.

Fig. 13

Installation

REMOVING THE ELECTRICAL KNOCK-OUT HOLE

WARNING: Always wear safety goggles and gloves during

installation.

- Choose the appropriate electrical knock-out hole to remove

for your installation type. Use the top hole (1) if your electrical

supply is in the cabinet and the back hole (2) if your electrical

supply is on the wall below the cabinet (refer to Fig. 10).

- Use a hammer and a athead screwdriver to gently punch out

the electrical knock-out hole.

- Place the grommet (CC) provided on the holes that have been

knocked out.

REMOVING THE VENTING HOLE

- Choose the venting hole to remove for your installation

type. Use the top hole (3) for a top venting installation

and the back hole (4) for a back venting installation.

- Carefully remove the cover (3 or 4) of the appropriate

venting hole using a at head screwdriver or needle

nose pliers (refer Fig. 11). Be careful not to leave any

debris inside the range hood (A).

- If you are venting indoors, unscrew the 2 screws

holding cover (5) in place and remove the cover as per

Fig. 12. DO NOT REMOVE ANY OTHER VENTING HOLE

COVER.

INSTALLING THE DAMPER

(SKIP THIS STEP IF YOU ARE USING INTERIOR VENTING)

NOTE:

Only install the damper if you are using a venting system that does not already

have a damper.

If this hood replaces an existing unit, the location of the air exhaust can vary

from one manufacturer to another. Ensure that the damper ts in the existing

opening before installing.

- Choose to install the damper (C) either in the top

position (3) for top venting or in the back position (4)

for back venting.

- Insert the damper (C) into the chosen hole in the range hood

(A), ensuring that the central ap (6) goes into the hole while

the two side aps (7) remain above it.

- Lift the lid (8) of the damper and screw the damper (C) to the

range hood (A) with the two short tapping screws (BB).

- Seal the damper (C) to the range hood (A) on all four sides with

duct tape.

Fig. 10

Fig. 11 Fig.12

11 CONGLOMKB.COM

Please contact customer.service@conglomkb.com or 1-877-333-0098 for further assistance.

Installation

Installation (continued)

INSTALLING THE CHARCOAL FILTER

(SKIP THIS STEP IF YOU ARE USING EXTERIOR VENTING)

NOTE:

The charcoal lter should only be installed if you are not using an external venting system.

- Turn over the range hood (A) and place its top on a protective surface.

- Unhook the charcoal lter support (9) from the support hook (10) and pull the charcoal lter support up.

- Place the charcoal lter (B) under the charcoal lter support (9). Ensure that the lter is placed horizontally, or the charcoal lter

support (9) will not close properly.

- Slide the charcoal lter support (9) to the left or right in its braces (11) until you can re-hook it on its support hook (10).

Installation (continued)

INSTALLING THE RANGE HOOD

DANGER: Turn off the power circuit breaker or the

power switch on the junction box before installing this

unit. Touching circuitry inside the range hood while it is

energized will result in death or serious injury.

DANGER: If installing this unit over a gas range, turn off

the gas at the source before installing or servicing this unit.

- Lift the range hood (A) up under the cabinet to determine

its nal position. Mark the location of the four keyhole

mounting slots (1) on the underside of the cabinet.

- Set the range hood (A) aside on a protective surface.

- Drill four pilot holes in the locations that you marked.

- Screw the four long tapping screws (AA) into the pilot

holes. Do not tighten the screws all the way – leave

the screw heads about 7 mm (0.28 in) from the cabinet

surface.

- Lift the range hood (A) into position, feeding the power

cable and the electrical wires through the power access

opening. Allow some slack in the cable and wires so that

the appliance can be moved if servicing is ever necessary.

- Position the range hood (A) so the large end (2) of the

keyhole mounting slots (1) are over the screws (AA). Then

push the range hood (A) toward the wall so the screws (AA)

are in the neck (3) of the keyhole slots. Tighten the screws

(AA). Ensure that the range hood (A) is securely fastened to

the cabinet before releasing it.

- If applicable, test the damper blade to ensure it rotates up

and down freely.

- If applicable, connect the duct work to the range hood (A).

Seal the joints with duct tape to ensure an airtight t.

FINAL STEP

- Reconnect the power supply cable and wires to the

electrical supply. Turn the power on and ensure that the

lights and fan are operating correctly.

13 CONGLOMKB.COM

Please contact customer.service@conglomkb.com or 1-877-333-0098 for further assistance.

Operation

NOTE:

The fan and lights operate independently of each other.

TURNING ON/OFF THE UNIT

- To turn on the fan, press the appropriate speed control

switch [Low Speed (2), Medium Speed (3), High Speed (4)]

to select the desired level of power. Once a button is

pressed, the previous speed mode will be cancelled.

- Press the power switch (1) to turn off the fan.

TURNING ON/OFF THE LIGHTS

- Press the light switch (5) to turn on and off the lights.

1 2 3 4 5

Maintenance

REPLACING FILTERS

When lters need replacing, exchange with similar. Also replace

lters that are damaged with punctures, bends, or broken

frames.

- Turn off the range hood and disconnect the power.

- Replace with an equivalent lter, then reconnect the

power.

REPLACING LIGHT BULBS

When light bulbs burn out, replace them with a 25W or 35W/JDR

16, GU10 twist and lock base light bulb.

- Turn off the range hood, disconnect it from its power

source, and ensure that the lights are cool.

- Turn the bulb (1) counter-clockwise and pull it out to

remove it.

- Push in the new bulb (2) and turn it clockwise. Do not

release the bulb until you are sure the bulb has been

securely installed. Then reconnect the power.

- If new bulbs do not operate, ensure that they are

inserted correctly.

DANGER: Turn off the power circuit breaker or the power

switch on the junction box before performing maintenance.

Touching circuitry inside the range hood while it is energized

will result in death or serious injury.

WARNING: Failure to replace worn out or damaged lters

will increase the risk of re.

WARNING: Light bulbs can become hot when turned on.

Do not touch bulbs until they are switched off and cooled.

Touching hot bulbs could cause serious burns.

15 CONGLOMKB.COM

Please contact customer.service@conglomkb.com or 1-877-333-0098 for further assistance.

Care and Cleaning

RANGE HOOD

WARNING: Failure to maintain basic standards of care and cleaning of the range hood will increase the risk of re.

The range hood should be cleaned (regularly internally and externally) to preserve its appearance and performance.

Do: Do Not:

- Always clean in the direction of the grain (original

polish lines).

- Clean the range hood periodically with hot, soapy

water and a clean cotton cloth.

- Always rinse well with clean water two or three

times after cleaning. Wipe completely dry with a

soft non-abrasive cloth.

- After cleaning, you may polish with a non-abrasive

stainless steel polish or cleaner. Always rub lightly

and with the grain

- Ensure that the venting system is free of debris, if

you have one.

- Do not use corrosive or abrasive detergents, steel

wool, or scouring pads. These will scratch and

damage the stainless steel surface.

- Do not use any products containing chloride,

uoride, iodide, or bromide on this product, as they

will deteriorate the surface rapidly.

- Do not allow cleaning compounds, salt solutions,

disinfectants, or bleaches to remain in contact with

the product for extended periods of time.

- Do not allow any deposits to remain for long

periods of time on the range hood. Rinse with

water immediately and wipe dry with a clean cloth.

- Do not let plaster dust or any other construction

residue enter the hood. During construction or

renovation, cover the hood.

- Combustible products used for cleaning such as

acetone, alcohol, ether, or benzol are highly explosive

and should never be used close to a range or stove.

FILTER

The lter tted by the factory is intended to lter out residue and grease from cooking. You do not need to replace them on a regular basis,

but you should keep them clean.

Do: Do Not:

- Clean the lter once a month using non-abrasive

detergents, either by hand or in the dishwasher.

When using a dishwasher, set the dishwasher to

a low temperature and a short cycle setting. The

lter may become discoloured in a dishwasher, but

this does not affect its performance.

- Allow lters to completely dry before re-installing

them in the range hood.

- Do not allow oil to accumulate over more than 80%

of the lter surface. Oil accumulations may drip oil

onto the range.

- Do not wash charcoal lter. The charcoal lter

should be replaced when it is covered in grease

and has reached its maximum absorbancy.

Troubleshooting

DANGER: Turn off the power circuit breaker or the power switch on the junction box before performing maintenance.

Touching circuitry inside the range hood while it is energized may result in serious injury or death.

Problem Solution

The range hood will not operate.

- Check that the power supply cable and all electrical wiring are properly

connected.

- Check that the power is turned on at the junction box or circuit breaker.

- Check that the wiring between the switch control and the control board are

connected properly.

The range hood vibrates when the fan is operating.

- Check that the range hood has been secured properly to the wall. Tighten into

position, if necessary.

- Check that the motor is secured in place. If not, then tighten the motor in place.

- Check that the fan is not damaged. If so, replace the fan.

The fans seem weak.

- Check that the duct size used is at least 152 mm (6 in) round. The range hood

will not function efciently with insufcient duct size.

- Check that the duct is not clogged with debris and the tight mesh on the wall

cap, if applicable, isn’t restricting air ow.

- Check that the damper unit is opening properly.

- Check that no birds or animals have nested in the duct.

The lights work, but the fan is not spinning, is stuck,

or is rattling.

- The thermal protection system detects if the motor is too hot to operate and

shuts the motor down. In this case, the motor will function properly after the

thermal protection system cools down (after approximately 10 min).

- Check that the fan isn’t jammed or scraping the bottom.

- If nothing else works, the motor may be defective or seized. If so, replace the

motor.

The range hood is not venting properly.

- Check that no birds or animals have nested in the duct.

- Check that the distance between the cooktop and the bottom of the range hood

is between 458 mm (18 in) and 710 mm (28 in).

- Check that duct work follows all requirements. Use round metal duct work with

a uniform diameter of 152 mm (6 in). The length of duct work must not exceed

35 ft (10.7 m). Reduce the length of duct work and the number of elbows if

necessary. Ensure that all joints are properly connected, sealed, and taped.

- Check that the duct does not open against the wind.

- Ensure that the power is on high speed for heavy cooking.

- Close all windows nearest to the range hood to eliminate sudden air gusts.

- To enhance the performance of the range hood, open slightly a window on the

opposite side of the house where the range hood vents outdoors.

A light does not work.

- Check to see if light bulb is burnt. If so, replace.

- Check the light bulb to see if it is loose. If so, tighten.

- Remove the problem bulb and insert one you know is working. If the properly

functioning light does not come on, the problem may be the light assembly.

Have the light assembly serviced or replaced.

17 CONGLOMKB.COM

Please contact customer.service@conglomkb.com or 1-877-333-0098 for further assistance.

Specications

Model Dimensions Rating Control Type Fan CFM Speeds Light Bulb Wattage Venting Options

QR025

757 mm (29.8 in) W

120~60Hz

1.6A

Push Button

300 ±

10%

High

2 x Max. 25W or 35W/

JDR 16, GU10 twist

and lock base light

bulb

Top venting

Back venting

Recirculating/

Inside venting

458 mm (18 in) D Medium

127 mm (5 in) H Low

WIRING DIAGRAM

Motor

White

Black

Blue

Grey

White

N L

Yellow & Green

White

Yellow

Brown

Red

Green

35W/JDR 16

Gu10 Light

Capacitor

5uf 370V AC

Specications (continued)

EXTERNAL DIAGRAM OF RANGE HOOD

18 mm

(0.69 in)

757 mm (29.8 in)

705 mm (27.75 in)

250 mm (9.81 in)

280 mm (11 in)

35 mm

(1.4 in)

(1.5 in)

38 mm

80 mm

(3.13 in)

28 mm

(1.1 in)

22 mm

(0.88 in) D

270.6 mm (10.65 in)

355 mm (14 in)

5 in

(127 mm )

458 mm (18 in)

193.5 mm

(7.62 in)

757 mm (29.8 in)

193.5 mm

(7.62 in)

TOP

BOTTOM

50 mm

(2 in)

250 mm

(9.81 in)

9 mm

(0.35 in)

21 mm

(0.8 in)

22 mm (0.88 in) D

19 CONGLOMKB.COM

Please contact customer.service@conglomkb.com or 1-877-333-0098 for further assistance.

Service Parts

If you are missing parts or if you require replacement parts, please contact our customer service team at customer.service@conglomkb.com or

1-877-333-0098 (8:30 am – 5 pm, EST, Monday–Friday). Identify the required part(s) and have the part number(s) ready.

K L

B CA

Part Description Code Quantity

A Damper QHR130 1

B Control Switch QHR106 1

C Wiring Box QHR138 1

D Capacitor QHR100 1

E Lights QHR121 2

F Light Base QHR123 2

G Motor 120V, 60Hz, 1.1A QHR126 1

H Fan QHR108 1

J Fan Guard QHR110 1

K Aluminum Filter QHR115 1

L Charcoal Filter QHR119 1

M Charcoal Filter Support QHR120 1

AA Long Tapping Screws (M5 x 12 mm) QHR131 4

BB Tapping Screws (M4 x 8 mm) QHR132 2

Imported by:

St-Laurent, Québec, H4S 2C3

1-877-333-0098

customer[email protected]

www.conglomkb.com

Made in China

Retain this manual for future use.

Presenza QR025 Installation guide

Brand: Presenza

Model: QR025

Category: Cooker hoods

Type: Installation guide

This manual is also suitable for

QR025 654OVSN016STS

Presenza QR025 654OVSN016STS

Key Features:

Efficient Ventilation: The QR025 boasts a high-performance motor that delivers up to 400 CFM of airflow, ensuring efficient removal of cooking fumes and odors.
Adjustable Fan Speed: Choose from three fan speeds to customize the airflow according to your cooking needs, from simmering to searing.

Download PDF

report

Presenza QR025 Installation guide

This manual is also suitable for

Presenza QR025 Installation guide

Related papers

Other documents