Viper 3305V Owner's manual

Congratulations

Congratulations on the purchase of your state-of-the-art security and re-

mote start system. Reading this Owner’s Guide prior to using your sys-

tem will help maximize the use of your system and its many features.

Please visit: www.viper.com – For general and additional guide infor-

mation. For any additional questions please contact your authorized

Directed dealer or contact Directed at 1-800-753-0600 (U.S. only).

Additional support is also available at: http://support.directed.com.

What is included

Welcome to the best generation of security. Your system contains ev-

erything you need.

s 4- button 2- way LCD remote control

s 4- button 1- way remote control

s In-vehicle status LED indicator light and push-button Valet switch

s Owner’s guide and Warranty card

Important information

Government Regulations

Read the Government Regulations section of this manual

prior to operating this system.

Your Warranty

Your Responder LC system comes with a warranty. Make sure you

receive the warranty registration card and proof of purchase from your

dealer indicating the product was installed by an authorized Directed

dealer. Please validate it online at www.prodregister.com/directed or

complete and return the warranty registration card.

Replacement remote controls

Your system comes with two remotes, the 7345V 2-way, and the

1-way companion remote 7145V. If additional remote controls are

desired, please see your authorized dealer or visit us at:

www.directedstore.com.

Contents

Congratulations .................................................................................................. 1

What is included .................................................................................................1

Important information ......................................................................................... 2

2-way LCD remote control .................................................................................... 3

LCD Screen ....................................................................................................... 4

LCD status icons / 2-way only ............................................................... 5

Remote control configuration ................................................................................ 6

2-way standard configuration ................................................................ 6

Remote control functions ...................................................................................... 7

2- way and 1- way .............................................................................. 7

Remote paging, 2-way ........................................................................................ 8

Signal paging features ......................................................................... 8

Programming your 2-way remote control ............................................................ 10

Beeps and Vibration, On/Off .............................................................. 10

Illumination On/Off ........................................................................... 10

Page notification ................................................................................ 11

Vehicle Select .................................................................................... 11

Using your system ............................................................................................. 12

Active arming .................................................................................... 12

Passive arming .................................................................................. 12

Multi-level security arming ................................................................... 14

Disarming ......................................................................................... 15

High Security Disarm .......................................................................... 15

Disarming without a transmitter............................................................ 16

Dome light control.............................................................................. 16

Silent mode ....................................................................................... 17

Panic mode ....................................................................................... 18

Valet mode ....................................................................................... 19

Nuisance prevention circuitry .............................................................. 20

Auxiliary outputs .............................................................................................. 21

Diagnostics ....................................................................................................... 21

Arming diagnostics ............................................................................ 22

Disarming diagnostics ........................................................................ 22

System status chirps ........................................................................... 23

Table of zones ................................................................................... 23

Interpreting zone diagnostics ............................................................... 24

Vehicle recovery system (VRS) ............................................................................ 24

Arming the VRS ................................................................................. 25

Triggered sequence, VRS .................................................................... 26

Disarming the VRS ............................................................................. 26

Code hopping ................................................................................................... 28

Owner recognition ............................................................................................ 28

Rapid resume logic ............................................................................................ 29

Power saver mode ............................................................................................. 29

Programming options ........................................................................................ 30

Installation options ............................................................................................ 33

Security & Convenience Expansions .................................................................... 34

System maintenance .......................................................................................... 36

Glossary of Terms .............................................................................................. 37

Patent Information ............................................................................................. 38

Government Regulations .................................................................................... 39

Limited lifetime consumer warranty ..................................................................... 41

3

2-way LCD remote control

Internal Antenna

Display

Command Buttons

Battery Compartment (at rear)

Programming Button (at rear)

Feature Description

Internal Antenna Used for transmitting and receiving information

Display The LCD screen provides visual confirmation of the vehicle

status using symbols and icons, such as alarm information.

Command buttons (4) Used to perform arming, disarming, auxiliary channel and

remote start commands

Programming Button

Used for customizing the remote control and for car

selection.

Battery Compartment 1 AAA battery powers the 2-way unit. Remove door on unit

rear to access.

4

LCD Screen





   























LCD Icon descriptions

1. Transmit 10. Battery level indicator

2. Out-of-range 11. Remote sending

3. Receive 12. Vibrate mode

4. Auxiliary output 2 or 3 13. Ignition

5. Garage door (no function) 14. Vehicle number

6. Warn away 15. Door

7. Alarm 16. Arm

8. Trunk or Hood 17. Disarm

9. Sensor

5

LCD status icons / 2-way only

Icon Description

1

On during remote command transmission to the vehicle.

2

On during remote command transmission to vehicle, but

command page is not received.

3

On during receipt of page from the vehicle to the

remote.

4

Displays which auxiliary is operating, or which security

sensor is in Warn Away or alarm state.

5

No Function

6

+

Displays when a security feature is tripped, but not to

full alarm.

7

+

Displays when a security is tripped to a full alarm state.

8

Trunk icon flashes a few seconds during full alarm and

then remains displayed until page is cleared.

9

Shock sensor icon flashes a few seconds during Warn

Away and full alarm, and then remains displayed until

page is cleared.

10

Battery icon displays current charge capacity of the

remote’s battery.

11

Bar indicates remote is sending.

12

Vibrator icon displays if remote is programmed for

vibrator notification. (See remote Programming section)

13

Ignition icon flashes a few seconds during full alarm,

then remains displayed until page is cleared.

6

Icon Description

Hood icon flashes a few seconds during full alarm, and

then remains displayed until page is cleared.

14

Displays the vehicle (1of 4) that the remote controls.

See “Vehicle Select” section.

15

Door icon flashes a few seconds, and then remains

displayed until page is cleared.

16

Arm icon flashes when doors are locking, and then

remains displayed until the system is disarmed.

17

Disarm icon flashes when doors are unlocking, and

then remains displayed until the system is armed.

Remote control conﬁguration

2-way standard conﬁguration

Arm

Disarm

Channel 2/Silent Mode

AUX

Panic

Channel 3

and

7

Remote control functions

The LCD remote control buttons are used to send commands to the sys-

tem. The descriptions below reﬂect the standard conﬁguration for this

system. The buttons can be custom conﬁgured for the user’s speciﬁc

needs by the installer.

2- way and 1- way

s Press and release to lock the doors and arm the vehicle.

s Press and release

to unlock the doors and disarm the vehicle.

s Press and release

AUX then press

or to activate Silent

Mode™ or press and hold for approximately two seconds to

activate optional auxiliary function such as trunk release.

The auxiliary output controls____________________

s Press and hold

for two seconds, to activate Panic.

s Press and release

and simultaneously to an activate

auxiliary convenience or expansion option.

The auxiliary output controls____________________

8

Remote paging, 2-way

The system operates at 434 MHz and incorporates Directed’s propri-

etary out-board technology transceiver. The high frequency combined

with Binary Data communication achieves superior range with two-

way communication.

Signal paging features

A page is the signal the control module sends to the remote control as

conﬁrmation of receipt of a command or alarm system status. When

the remote control receives a page it generates a page notiﬁcation

to the user (notiﬁcations are audible beeps and-or vibration), and the

LCD icons display current system status.

Command Page

When a command (arm/disarm, or auxiliary channel) from the re-

mote control is sent and received, the system will send a command

page back to conﬁrm receipt.

Alarm Page

If the alarm system is triggered while armed, an Alarm Page will be

sent to the remote control. When the remote receives an Alarm Page,

the LCD icons will display the alarm system status information and the

remote control will generate beeps and-or vibration.

An Alarm Page alert is a series of 5 groups of 4 rapid beeps (shock,

trunk, door, ignition, or hood trigger) and the LCD icon that caused

the alarm will display. The remote will beep and or vibrate every 60

seconds to alert the user that the alarm system was triggered and will

continue until the alarm page is cleared.

9

Page Recognition (Acknowledgement)

To clear a page alert/notiﬁcation, quickly press any button on the

remote control. This can be performed at any time during or after the

page notiﬁcation has occurred.

The remote control will not send a command to the system at this time;

it will only clear future repeats of the page notiﬁcation. The next time

a button is pressed on the remote control it will send a command to

the system.

Out of range notiﬁcation

If a command is issued from the remote, but the remote is set to the

incorrect vehicle or is beyond the range of the vehicle to receive the

command, the remote responds with 3 sets of 2 quick beeps and the

icon will ﬂash 3- times.

10

Programming your 2-way remote control

To enter programming mode:

Press and hold the

P

button located on the back of the remote con-

trol until one long beep sounds. You can now customize the remote’s

response feedback. If no buttons are pressed within 5 seconds, pro-

gramming mode is exited; the remote sounds 2 beeps.

Beeps and Vibration, On/Off

Press to select beep/vibration On or Off, or one of the below

settings.

Beeps/Vibrate Response Icon*

Beeps only

1 beep

Vibrate only

1 vibrate

Beep & Vibrate

1 beep & 1 vibrate

&

No Beep & No

Vibrate

1 long beep

*Displays during programming

Illumination On/Off

Press to select LCD backlight illumination On/Off. The LCD back-

light will illuminate when a remote button is pressed, or an alarm status

page is received.

LCD backlight settings Programming

On

1 beep backlight On

Off

2 beeps backlight Off

11

Page notiﬁcation

The remote control can notify the user of a page by emitting beeps

if the vehicle’s status changes, for example, if a door is unlocked, or

any vehicle violation.

On the 2-way remote, press

to select page On/Off. One beep is

page On. Two beeps is page Off.

When programmed off the remote does not give any notiﬁcation that

a page was received from the vehicle.

Page notification Response

On

1 beep

Off

2 beeps

Note: If programmed Off, the remote receives no notiﬁcation of alarm

triggers. The remote only receives command, such as arm or disarm,

information.

Vehicle Select

If multiple cars are used with the system: Press

P

for 1 second and re-

lease (holding for too long enters programming mode) to select which

vehicle is to be controlled by the remote control. Repeat this procedure

to scroll to next vehicle selection.

Note: If a Warn Away or alarm trigger occurs in a vehicle not se-

lected, remote control functions automatically switch to that speciﬁc

vehicle and remains in this vehicle select state. The Vehicle Select

procedure must be used to return to the previous vehicle selection.

12

Using your system

The buttons described in this manual correspond to the standard con-

ﬁg u ra tion. However, the remote commands may be customized to suit

your speciﬁc needs. See your installer for additional details.

Active arming

You can arm the system by pressing of your remote for one second.

When the system arms, from the vehicle you will hear a short siren

sound, or chirp, and see the parking lights ﬂash once. If the power

door locks are con trolled by the system, the doors will also lock.

While the sys tem is armed, the in-vehicle’s status LED will ﬂash ap-

proximately once per sec ond, indicating that the system is actively pro-

tect ing your vehicle. If you hear a second chirp after arming and note

that the in-vehicle’s status LED is ﬂashing in groups, see the Diagnostics

Section of this guide. This extra chirp is called Bypass No ti ﬁ ca tion.

The LCD remote responds to active arming with one beep and the

icon will ﬂash 5- times to indicate successful arming of the system.

If the LCD remote beeps twice after arming, the system has detected

an active sensor that should be checked. For example, a door open

icon will be displayed ﬂashing 5- times on the LCD screen.

Passive arming

The system can be programmed to arm itself au to mat i cal ly (called pas sive

arming). If the system is programmed for passive arming, it will automati-

cally arm 30 seconds after the ignition is turned off and the system detects

that you have left the vehicle by opening and closing a door. Whenever

the system is in its 30 - sec ond passive arming count down, the in-vehicle

13

status LED will ﬂash twice as fast as it does when the system is armed. At

the 20 - second point of the countdown, the siren will chirp to indicate that

the system is about to arm. At the 30 - second point, the parking lights will

ﬂash to indicate that the system is armed.

The LCD remote responds to passive arming with one beep and the

icon will ﬂash 3- times to indicate successful arming of the system.

If any protected entry point (such as a door or a switch-protected trunk

or hood) is open, the system will not passively arm (unless forced pas-

sive arming is programmed on. See Programming Options section.)

Ad di tion al ly, if a door, hood or trunk is triggered during the arming

count down, the 30 - second count down starts over.

When the system is armed:

s Light impacts trigger the Warn Away® signal. When triggered,

the siren chirps and the parking lights ﬂash for a few seconds.

s Heavy impacts trip a Triggered Sequence. The sequence consists

of the siren sounding continuously and the parking lights ﬂashing

for a pre-programmed period, which can range in duration from

1 to 180 seconds.

s If a door is opened, the system will immediately start chirping the

siren and ﬂashing the parking lights. Three seconds later, the siren

out put changes to a continuous blast. This pro gres sive re sponse

gives you time to disarm the sys tem with your LCD remote if you

inadvertently open the door while the system is armed, while

still providing instant re sponse (even if the door is immediately

closed).

s Turning on the ignition key will trip the same progressive re sponse

as opening a door.

s The optional starter kill prevents the vehicle’s starter from cranking.

s Any full trigger of the alarm system will immediately send an

alarm page to your remote informing you that your vehicle should

14

be checked.

Multi-level security arming

Multi-Level Security Arming allows you to select which of the security

system’s inputs or sensors are active, or are bypassed when the system

is armed. (See the Table of Zones section of this guide)

Press

one time to arm the system, siren chirps one time. Pressing

again activates Multi-Level Security Arming.

Each time

is pressed consecutively, a different security level is se-

lected, as described in the below table:

Press

Siren chirps Zone bypassed

Twice Twice followed by 1 long chirp 2

3 times 3 times followed by 1 long chirp 4

4 times 4 times followed by 1 long chirp 2 & 4

5 times 5 times followed by 1 long chirp all zones except 5

Each press of the button ascends to the next security level, the re-

mote sounds 1 beep, and the lock icon ﬂashes 5 times.

Multi-Level Security Arming applies to a single arming cycle. Once

the system is disarmed and then re-armed, all the zones will be active

again.

15

Disarming

To disarm the system, press . You will hear two chirps, and the park-

ing lights will ﬂash twice. If the power locks are connected to the sys-

tem, the doors will unlock. If the siren chirps either four or ﬁve times

when disarming, refer to the Diagnostics section of this guide. This is

called Tamper Alert.

The remote sounds 2 beeps and the unlock icon

ﬂashes 5 times,

when the system is disarmed.

When disarming after the system has been triggered, the remote

sends a diagnostic notiﬁcation, as described below:

s If a sensor triggered the system the remote emits 4 quick beeps,

and the LCD screen ﬂashes the zone indicator to display which

sensor tripped the alarm.

s If a switch (Zone 1, 3 or 5) triggered the system, the remote emits

4 quick beeps, and the LCD screen ﬂashes the zone indicator to

display which switch tripped the alarm.

s If the system was triggered enough times that NPC (See Nui-

sance Prevention Circuitry) is active, the remote emit 5 beeps.

High Security Disarm

High Security Disarm makes it possible to silence and reset the system

when it is triggering, without disarming. If the system is triggered, and

the siren sounds for longer than six seconds, pressing the

button

will stop the trigger and return the system to an armed state. The sys-

tem does not disarm, but rather reset. This prevents you from disabling

the system should you want to disarm without visually checking the

vehicle. Pressing the

button again after resetting the system, will

disarm the system. Pressing the

button during the ﬁrst six seconds

of the triggered sequence disarms the system immediately. The six sec-

16

ond timer is provided for your convenience, in case you accidentally

trigger the system.

Disarming without a transmitter

This feature allows you to disarm the security sys tem without the remote

trans mit ter should it be lost, dam aged, or disabled. In order to dis arm

the system with out a remote transmitter, you must have the ve hi cle’s

ig ni tion key and know where the Valet button is located. Be sure to

check with the installer for the location and the number of presses of

the Valet button required to disarm the system.

To disarm the security system:

1. Turn the ignition to the ON position.

2. Press and release the Valet button the preset number of times

(one, the factory setting, to ﬁve times) within 15 seconds.

After ﬁve seconds the sys tem disarms. If the system does not dis-

arm, you may have waited too long.

Turn the ignition off and on and try again.

Location of Valet Button _________________________________

Number of Pulses _________________________________

The unit may respond to one to ﬁve pulses of the Valet button, when

disarming. Check with your installer to discuss how you want the

system conﬁgured.

Note: as a precaution, if programmed for passive arming the system

should be placed into Valet Mode until a remote is available.

Dome light control

17

Security only

The dome light activates for 30 - seconds after the system is disarmed.

Ignition controlled

The dome light activates for 30 - seconds after the ignition is turned

Off. (may be programed to On or Off, by the dealer installer)

Silent mode

To temporarily turn off the arm or disarm chirps, use Silent Mode™.

Press AUX for less than one second before arming or disarming, and

the conﬁrmation chirp(s) will be eliminated for that one op er a tion only.

If you want the arm/disarm chirps turned off permanently, your dealer

can do this for you.

The Warn Away response to lighter impacts is bypassed if the system

is armed using Silent Mode. This ensures that no chirps will be emitted

by the siren in an area you want chirp-free. The system is still capable

of triggering, but the Warn Away® response is bypassed.

The LCD remote responds with the normal arm/disarm notiﬁcations in

silent mode. If the remote has beeps programmed On, it will beep.

Page is loading ...

Viper 3305V Owner's manual

This manual is also suitable for

Viper 3305V Owner's manual

Related papers

Other documents