Weider XP23 User manual

Brand: Weider

Model: XP23

Category: Fitness, gymnastics & weight training

Type: User manual

This manual is also suitable for

WESY81081

USERÕS

MANUAL

Model No. WESY81081

Serial No.

The serial number is found in the

location shown below. Write the

serial number in the space above.

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manu-

al for future reference.

Serial

Number

Decal

QUESTIONS?

As a manufacturer, we are

committed to providing complete

customer satisfaction. If you

have questions, or if there are

missing or damaged parts, we

will guarantee complete satisfac-

tion through direct assistance

from our factory.

TO AVOID UNNECESSARY

DELAYS, PLEASE CALL DIRECT

TO OUR TOLL-FREE CUSTOMER

HOT LINE. The trained techni-

cians on our customer hot line

will provide immediate assis-

tance, free of charge to you.

CUSTOMER HOT LINE:

1-800-999-3756

Mon.ÐFri., 6 a.m.Ð6 p.m. MST

PATENT PENDING

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Cable Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Weight Resistance Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Trouble-shooting and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Ordering Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

Note: A PART LIST/EXPLODED DRAWING and a PART IDENTIFICATION CHART are attached to the center of

this manual. Remove the PART LIST/EXPLODED DRAWING and the PART IDENTIFICATION CHART before

beginning assembly.

Table of Contents

Limited Warranty

ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-

rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This

warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing

or repairing, at ICON's option, the product at one of its authorized service centers. All products for which war-

ranty claim is made must be received by ICON at one of its authorized service centers with all freight and other

transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-autho-

rized by ICON. This warranty does not extend to any product or damage to a product caused by or attribut-

able to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON

authorized service center, products used for commercial or rental purposes, or products used as store display

models. No other warranty beyond that specifically set forth above is authorized by ICON.

ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection

with the use or performance of the product or damages with respect to any economic loss, loss of property,

loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential dam-

ages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequen-

tial damages. Accordingly, the above limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-

chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.

Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation

may not apply to you.

This warranty gives you specific legal rights. You may also have other rights which vary from state to state.

ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813

WEIDER is a registered trademark of ICON Health & Fitness, Inc.

WARNING: Before beginning this or any exercise program, consult your physician. This is especially

important for persons over the age of 35 or persons with pre-existing health problems. Read all

instructions before using. ICON assumes no responsibility for personal injury or property damage

sustained by or through the use of this product.

Important Precautions

1. It is the responsibility of the owner to ensure

that all users of the training system are ade-

quately informed of all precautions.

2. Read all instructions in this manual and in

the accompanying literature before using the

training system.

3. If you feel pain or dizziness at any time while

exercising, stop immediately and begin cool-

ing down.

4. Use the training system only on a level sur-

face. Cover the floor or carpet beneath the

training system for protection.

5. Inspect and tighten all parts often. Replace

any worn parts immediately.

6. Make sure the cables remain on the pulleys

at all times. If the cables bind while you are

exercising, stop immediately and make sure

the cables are on all of the pulleys.

7. Always stand on the foot plate when perform-

ing an exercise that could cause the training

system to tip.

8. Keep children under the age of 12 and pets

away from the training system at all times.

9. Keep hands and feet away from moving parts.

10. The training system is designed to be used

by only one person at a time.

11. Always wear athletic shoes for foot protec-

tion when exercising.

12. Never release the press arm, butterfly arms,

leg lever, lat bar, row bar or handle while

weights are raised. The weights will fall with

great force.

13. Always disconnect the lat bar or row bar

from the training system when performing an

exercise that does not use them.

14. The training system is intended for home use

only. Do not use the training system in a

commercial, rental or institutional setting.

To reduce the risk of serious injury, read the following important

precautions before using the training system.

WARNING:

ASSEMBLED

DIMENSIONS:

Height: 77 in.

Width: 38 in.

Length: 61 in.

Low Pulley

Station

Foot Plate

Row Bar

High Pulley Station

Leg Lever

Butterfly Arm

Press Arm

Shroud Covering

Weight Stack

Seat

Backrest

Thank you for selecting the versatile WEIDER

XP23

Training System. The XP23 offers a selection of

weight stations designed to develop every major mus-

cle group of the body. Whether your goal is to tone

your body, build dramatic muscle size and strength or

improve your cardiovascular system, the XP23 will

help you to achieve the results you want.

For your benefit, read this manual carefully before

using the WEIDER

XP23 Training System. If you

have additional questions, please call our Customer

Service Department toll-free at 1-800-999-3756,

Monday through Friday, 6 a.m. until 6 p.m. Mountain

Time (excluding holidays). To help us assist you,

please note the product model number and serial

number before calling. The model number is

WESY81081. The serial number can be found on a

decal attached to the WEIDER

XP23 Training System

(see the front cover of this manual).

Please use the drawing below to familiarize your-

self with the major parts and how they fit together.

Before You Begin

Curl Pad

Lat Bar

Note: This introduction will save you more

time than it takes to read it!

Identifying Parts

To help you identify the small parts used in assem-

bly, we have included a PART IDENTIFICATION

CHART located in the center of this manual. Place

the chart on the floor or work table and use it to

quickly identify different parts as you open the pack-

ages for each step.

Note: Some small parts may have been pre-attached

for shipping. If a part is not in the parts bag, check to

see if it has been pre-attached.

Orienting Parts

As you assemble this product, be sure that all parts

are oriented as shown in the drawings.

Tightening of Parts

Tighten all parts as you assemble them, unless

instructed to do otherwise.

Lining Up the Tools

Assembly requires the following tools (not included):

¥ Two (2) adjustable wrenches

¥ One (1) standard screwdriver

¥ One (1) phillips screwdriver

¥ One (1) rubber mallet

¥ Lubricant, such as grease or petroleum jelly,

and soapy water

¥ Tape, such as clear tape or masking tape

Assembly will be more convenient if you have a

socket set, a set of open-end or closed-end wrenches

or a set of ratchet wrenches.

Giving Yourself a Good Start

Before you begin the assembly process itself, take

the time to complete the steps outlined here.

Clearing the Workspace

Clear a workspace that is large enough to hold all

parts and allow you to walk all the way around the

assembled equipment.

Unpacking the Box

To make the assembly process as smooth as possi-

ble, we have broken it into separate stages. All parts

used in each stage are found in individual packages

in the shipping box. Place all parts in a cleared area

and remove the packing materials. Do not dispose of

the packing materials until assembly is completed.

Important: Wait until you begin each assembly

stage to open the parts bag labeled for that

assembly stage.

Assembly

Making Things Easier for Yourself

Everything in this manual is designed to ensure

that the assembly of our products can be complet-

ed successfully by anyone. However, it is impor-

tant to recognize that your new equipment is a

sophisticated product with many small parts. The

assembly process will take timeÑpossibly several

hours. Most people find that by setting aside plen-

ty of time, and by deciding to make the task

enjoyable, assembly will go smoothly. You may

want to complete the process over a couple of

evenings.

The Four Stages of the Assembly Process

Frame Assembly

You will begin by assembling the base and the

upright frames that serve as the skeleton of the

equipment. The seats and all moving parts will be

attached to the frame.

Arm Assembly

Completes the press and butterfly arms that you

operate while you are exercising.

Cable Assembly

Completes the cables and pulleys that connect the

moving arms with each other and with the weights.

This ties the different parts together and makes the

equipment function as a unit

Seat Assembly

Completes the seats and backrests that support

your body while you are exercising.

1. Before beginning assembly, make sure you have

read and understood the information on page 5.

Locate and open the parts bag labeled ÒFRAME

ASSEMBLY.Ó

Press a 2Ó Square Outer Cap (51) onto each end of

the Stabilizer (5).

Insert two 5/16Ó x 2 3/4Ó Carriage Bolts (14) up

through the Stabilizer (5) and place it flat on the floor.

2. Press a 2Ó Square Inner Cap (21) into the end of the

Base (8).

Insert two 5/16Ó x 2 1/2Ó Carriage Bolts (52) up

through the Base (8).

Place the Base (8) on the floor with the holes in the

mounting bracket (A) over the Carriage Bolts (14) in

the Stabilizer (5).

Frame Assembly

3. Press a 1Ó x 2Ó Inner Cap (11) into the top of the Rear

Upright (18).

Slide the Rear Upright (18) onto the 5/16Ó x 2 3/4Ó

Carriage Bolts (14) in the Stabilizer (5). Hand tighten

a 5/16Ó Nylon Locknut (53) onto each Carriage Bolt.

Do not tighten the Nylon Locknuts yet. Make sure

the Upright is oriented as shown. The wide side

of the bracket (B) on the lower end of the Upright

(18) must be facing the front of the unit.

Slide the Front Upright (42) onto the 5/16Ó x 2 1/2Ó

Carriage Bolts (52) in the Base (8). Hand tighten a

5/16Ó Nylon Locknut (53) onto each Carriage Bolt.

CAUTION: Make sure the Upright is oriented as

shown. The indicated holes must be closer to the

rear of the unit.

Do not tighten the Nylon Locknuts yet.

Holes

4. Set four Weight Bumpers (19) onto the Base (8) and

align them with the indicated holes.

Insert both Weight Guides (23) through the Weight

Bumpers (19) and the holes in the Base (8).

Slide eight Weights (26) onto the Weight Guides (23).

Make sure all of the Weights are turned so the pin

grooves are on the same side and are oriented as

shown on the drawing.

Grooves

5. Press the Weight Tube Bumper (64) into the end of

the Weight Tube (25).

Insert the Weight Tube (25) into the stack of Weights

(26). Make sure the pin on the Weight Tube is

resting in the pin groove in the upper Weight.

Lubricate the insides of the holes in the Top Weight

(16).

With the slot facing down, slide the Top Weight onto

the Weight Guides and set it on the stack of Weights

(26).

6. Slide two 5/16Ó Flat Washers (56) onto two

5/16Ó x 2 3/4Ó Bolts (67).

Place the Top Frame (1) on top of the Front Upright

(42) and align the indicated holes with the holes in

the bracket (C) on the Upright.

Insert the 5/16Ó x 2 3/4Ó Bolts (67) through the Top

Frame (1) and the bracket (C) on the Front Upright

(42). Hand tighten a 5/16Ó Nylon Locknut (53) onto

each Bolt.

Do not tighten the Locknuts yet.

Groove

Slot

7. Slide two 5/16Ó Flat Washers (56) onto two

5/16Ó x 1 3/4Ó Bolts (58).

Align the holes in the bracket on the Top Frame (1)

with the holes in the Rear Upright (18). Insert the

5/16Ó x 1 3/4Ó Bolts (58) and hand tighten two 5/16Ó

Nylon Locknuts (53) onto them.

8. Attach the upper ends of the Weight Guides (23) to

the bracket (D) on the Top Frame (1) with two 5/16Ó x

1 1/2Ó Bolts (61) and two 5/16Ó Nylon Locknuts (53).

Tighten the Nylon Locknuts, but be careful not to

overtighten them since this may damage the weight

guides.

9. Press a 1 1/2Ó Square Inner Cap (33) into the end of

the Seat Frame (36).

Insert two 5/16Ó x 2 3/4Ó Bolts (67) through the

Support Plate (27) and the indicated holes in the

Front Upright (42). Place the mounting bracket (E) on

the Seat Frame (36) over the two Bolts. Tighten a

5/16Ó Nylon Locknut (53) onto each Bolt.

Make sure the Support Plate (27) is oriented as

shown in the drawing.

Tighten all Nylon Locknuts used in steps 3

through 9.

10. Locate and open the parts bag labeled ÒARM

ASSEMBLY.Ó

Press Arm Assembly. Align the welded spacers on

the Press Frame (12) with the tube (F) on the Base

(8). Lubricate the 3/8Ó x 8Ó Bolt (59). Attach the Press

Frame to the Base with the Bolt and a 3/8Ó Nylon

Locknut (63).

Arm Assembly

59 Lubricate

Welded Spacers

11. Press a 2Ó Square Inner Cap (21) into the top end of

each Press Arm (46).

Press a 1Ó Round Inner Cap (49) into the indicated

hole on each Press Arm (46).

Attach each Press Arm (46) to the Press Frame (12)

with two 5/16Ó x 2 3/4Ó Bolts (67) and two 5/16Ó Nylon

Locknuts (53).

12. Butterfly Arm Assembly. Identify the Right Arm (48)

and the Left Arm (47) by imagining yourself sitting on

the seat. Note the position of the welded bracket (G)

on each Arm. Arm identification is very important

for this step.

Lubricate both axles (H) on the Top Frame (1). Slide

the Right Butterfly Arm (48) onto the right axle. Note:

Be careful not to confuse the Right and Left

Butterfly Arm. Make sure the upper end of the

Right Butterfly Arm is behind the indicated brack-

et (I) on the Top Frame.

Tap two 1Ó Retainers (4) and a 1Ó Round Cover Cap

(3) onto the Right Axle. To do this, place the two

retainers on top of the Cover Cap and tap on the

Cover Cap with a rubber mallet. Make sure the teeth

on the Retainers (4) bend towards the Cover Cap

(3), as shown in the inset drawing.

Attach the Left Butterfly Arm (47) in the same man-

ner. Press a 2Ó Square Inner Cap (21) into each end

of the crossbar on the Top Frame (1). Press a 2Ó

Square Inner Cap (21) into the lower end of each

Butterfly Arm (47, 48).

Lubricate the lower end of each Butterfly Arm with

soapy water and slide a Foam Pad (45) onto each

Arm.

Press two 1Ó Round Inner Caps (49) into the indicat-

ed holes in the crossbar on the Top Frame (1).

Axle

14. Locate and open the parts bag labeled ÒCABLE

ASSEMBLY AND PULLEYS.Ó For Cable identifica-

tion and routing during steps 14Ð28, refer to the

Cable Diagram and Cable ID Chart on page 16.

Locate the Short Cable (9). It is approximately 127Ò

long. Wrap the end with the ball around a 3 1/2Ó

Pulley (35) in the direction shown.

Attach the 3 1/2Ó Pulley to the Top Frame (1) with a

3/8Ó x 3 1/2Ó Bolt (54), a 3/8Ó Flat Washer (55) and a

3/8Ó Nylon Locknut (63).

Make sure the Short Cable (9) is between the

Pulley (35) and the welded hook (K) on the Top

Frame (1).

Cable Assembly

13. Press a 1 1/2Ó Square Inner Cap (33) into the Leg

Lever (29).

Lubricate a 5/16Ó x 2 1/2Ó Bolt (22). Attach the Leg

Lever (29) to the Seat Frame (36) with the Bolt and a

5/16Ó Nylon Jamnut (80). Do not overtighten the

Nylon Jamnut. The Leg Lever should pivot freely.

Thread a 5/16Ó Plain Nut (32) one half inch onto the

5/16Ó x 2Ó Eyebolt (44). Thread the Eyebolt into the

Leg Lever (29). Tighten the Plain Nut to prevent the

Eyebolt from turning.

Note: The use of remaining parts from the ARM

ASSEMBLY parts bag will be explained in step 31.

22 Lubricate

15. Wrap the Short Cable (9) around a ÒVÓ-Pulley (6) in

the direction shown.

Attach the ÒVÓ-Pulley (6) and a Long Cable Trap (50)

to the indicated bracket (J) with a 3/8Ó x 2 1/4Ó Bolt

(65) and a 3/8Ó Nylon Locknut (63). Make sure the

Long Cable Trap is positioned as shown, so it will

hold the Cable in place.

17. Move to the other side of the unit. Wrap the Short

Cable (9) around a 3 1/2Ó Pulley (35) in the direction

shown.

Attach the 3 1/2Ó Pulley (35) and a Cable Trap (66) to

the Right Butterfly Arm (48) with a 3/8Ó x 2Ó Bolt (62)

and a 3/8Ó Nylon Locknut (63).

Make sure the Cable Trap (66) is positioned as

shown.

16. Wrap the Short Cable (9) around a 3 1/2Ó Pulley (35)

in the direction shown.

Attach the 3 1/2Ó Pulley (35) and a Cable Trap (66) to

the Left Butterfly Arm (47) with a 3/8Ó x 2Ó Bolt (62)

and a 3/8Ó Nylon Locknut (63).

Make sure the Cable Trap (66) is positioned as

shown.

Route the Short Cable (9) under the Top Frame (1)

between the Pulley (35) and the crossbar.

Crossbar

18. Remove the 1/2Ó Nylon Locknut (68) from the welded

bolt (L) on the Top Frame (1). Slide the Pulley

Bracket (20) onto the bolt and secure it with the Nylon

Locknut. Tighten the Locknut, but make sure the

Pulley Bracket can pivot freely.

Remove the 3 1/2Ó Pulley (35) from the Pulley

Bracket (20). Wrap the Short Cable (9) around the

Pulley in the direction shown.

Re-attach the 3 1/2Ó Pulley (35) to the Pulley Bracket

(20) with the 3/8Ó x 1 3/4Ó Bolt (83) and the 3/8Ó Nylon

Jamnut (57).

19. Move to the other side of the unit. Remove the 3 1/2Ó

Pulley (35) attached to the Pulley Plates (31).

Wrap the Short Cable (9) around the 3 1/2Ó Pulley

(35) in the direction shown.

Re-attach the Pulley (35) to the Pulley Plates (31)

with the 3/8Ó x 1 1/2Ó Bolt (60) and the 3/8Ó Nylon

Jamnut (57).

20. Wrap the Short Cable (9) around a 3 1/2Ó Pulley (35)

in the direction shown. Attach the 3 1/2Ó Pulley (35) to

the front bracket (M) underneath the Top Frame (1)

with a 3/8Ó x 2Ó Bolt (62) and a 3/8Ó Nylon Locknut

(63). Make sure the Bolt (62) is inserted from the

direction shown on the drawing.

Wrap the Short Cable (9) around a 3 1/2Ó Pulley (35)

in the direction shown. Attach the 3 1/2Ó Pulley (35) to

the rear bracket (N) underneath the Top Frame (1)

with a 3/8Ó x 2Ó Bolt (62) and a 3/8Ó Nylon Locknut

(63). Make sure the Bolt (62) is inserted from the

direction shown on the drawing.

21. Make sure the Short Cable (9) is in the groove of

all Pulleys and that the Cable and the Pulleys

move smoothly.

Attach the closed loop on the end of the Short Cable

(9) to the Weight Tube (25) with the 5/16Ó x 1 3/4Ó

Bolt (58) and a 5/16Ó Nylon Locknut (53). It will be

necessary to lift the Weight Tube and the Top Weight

to insert the Bolt through the Weight Tube and the

loop on the Cable.

22. Locate the Long cable (2). It is approximately 215Ó

long. Wrap the end with the ball around the Low

Pulley (40) in the direction shown. Attach the Pulley

to the bracket (O) on the Base (8) with a 3/8Ó x 2Ó

Bolt (62) and a 3/8Ó Nylon Locknut (63).

Thread the Long Cable (2) through the Press Frame

(12). Wrap the Long Cable around a 3 1/2Ó Pulley

(35) in the direction shown. Attach the Pulley to the

Front Upright (42) with a 3/8Ó x 3 1/2Ó Bolt (54), a

Cable Trap (66), a 3/8Ó Flat Washer (55) and a 3/8Ó

Nylon Jamnut (57).

22 42

23. Remove the free Pulley (35) attached to the Pulley

Plates (31). Wrap the Long Cable (2) around the

Pulley in the direction shown.

Re-attach the Pulley (35) to the Pulley Plates (31)

with the 3/8Ó x 1 1/2Ó Bolt (60) and the 3/8Ó Nylon

Jamnut (57).

25. Thread the Long Cable (2) through the Press Frame

(12). Wrap the Long Cable around a 3 1/2Ó Pulley

(35) in the direction shown.

Attach the Pulley to the Press Frame with a 3/8Ó x

3 1/4Ó Bolt (69), a Cable Trap (66), a 3/8Ó Flat Washer

(55) and a 3/8Ó Nylon Jamnut (57).

26. Wrap the Long Cable (2) around a ÒVÓ- Pulley (6) in

the direction shown. Attach the ÒVÓ-Pulley to the

bracket (P) on the Seat Frame (36) with a 3/8Ó x

3 1/4Ó Bolt (69), a Cable Trap (66), a 3/8Ó Flat Washer

(55) and a 3/8Ó Nylon Locknut (63).

Note: The ÒVÓ-Pulley (6) should be attached to the

third hole, counting from the Front Upright (42).

27. Wrap the Long Cable (2) around a 3 1/2Ó Pulley (35)

in the direction shown. Attach the Pulley to the Press

Frame (12) with a 3/8Ó x 3 1/4Ó Bolt (69), a Cable

Trap (66), a 3/8Ó Flat Washer (55) and a 3/8Ó Nylon

Jamnut (57).

24. Move to the other side of the unit. Wrap the Long

Cable (2) around a 3 1/2Ó Pulley (35) in the direction

shown.

Attach the Pulley to the Front Upright (42) with a 3/8Ó

x 3 1/2Ó Bolt (54), a Cable Trap (66), a 3/8Ó Flat

Washer (55) and a 3/8Ó Nylon Jamnut (57).

28. Wrap the Long Cable (2) around a 3 1/2Ó Pulley (35)

in the direction shown. Attach the Pulley to the Front

Upright (42) with a 3/8Ó x 3 1/2Ó Bolt (54), a Cable

Trap (66), a 3/8Ó Flat Washer (55) and a 3/8Ó Nylon

Jamnut (57).

Attach the closed loop on the end of the Long Cable

(2) onto the Eyebolt (44) with a Cable Clip (73). Note:

Cable Clips are located in the parts bag labeled

ÒSEAT ASSEMBLY.Ó

29. Locate and open the parts bag labeled ÒSEAT

ASSEMBLY.Ó

Attach the Backrest (41) to the Front Upright (42) with

two 1/4Ó x 2 1/2Ó Screws.

Seat Assembly

30. Insert the 1/4Ó x 2Ó Carriage Bolt (38) into the center

hole in the Seat Plate (37). Attach the Seat Plate to

the Seat (13) with two 1/4Ó x 1/2Ó Screws (17).

Insert the 1/4Ó x 2Ó Carriage Bolt (38) into the indicat-

ed hole in the Seat Frame (36). Tighten a 1/4Ó Nylon

Locknut (82) with a 1/4Ó Flat Washer (81) onto the

Carriage Bolt.

Attach the other end of the Seat (13) to the Seat

Frame (36) with a 1/4Ó Flat Washer (81) and a 1/4Ó x

2Ó Bolt (71).

31. Press two 3/4Ó Round Inner Caps (34) into each Pad

Tube (28).

Insert one Pad Tube into the Seat Frame (36). Slide a

Foam Pad (30) onto each end of the Pad Tube.

Insert the other Pad Tube into the Leg Lever (29).

Slide a Foam Pad (30) onto each end of the Pad

Tube.

Miscellaneous Assembly

32. Attach the Curl Pad (24) to the Curl Post (10) with

two 1/4Ó x 1/2Ó Screws (17).

Slide the Curl Post (10) onto the Seat Frame (36) so

each of the welded brackets are between the Seat

Frame and the bracket on the Leg lever (29). Secure

the Curl Post with the 5/16Ó x 2Ó Knob (72).

Make sure the Leg Lever (29) can be turned freely

after the Curl Post (10) is mounted.

33. Align the Left Shroud (78) with the holes in the Top

Frame (1), Base (8) and the two Uprights (18, 42)

and attach it with 14 of the #8 x 1/2Ó Tap Screws (7).

Move to the other side of the unit and attach the

Right Shroud (79) which is the one with the opening

for adjusting the Weights. Align the Right Shroud with

the holes in the Top Frame (1), Base (8) and the two

Uprights (18, 42) and attach it with 14 of the #8 x 1/2Ó

Tap Screws (7).

Welded

Brackets

34. Make sure that all parts have been properly tight-

ened. The use of the remaining parts will be

explained in ADJUSTMENT, beginning on page 17

of this manual.

Before using the home gym system, pull each

cable a few times to be sure that the cables move

smoothly over the pulleys. If one of the cables does

not move smoothly, find and correct the problem.

IMPORTANT: If the cables are not properly

installed, they may be damaged when heavy

weight is used. If there is any slack in the

cables, you will need to remove the slack by

tightening the cables. See TROUBLE-SHOOT-

ING AND MAINTENANCE on page 19.

Cable Diagram

The Cable Diagram below shows the proper routing of the Short Cable (9) and the Long Cable (2). The numbers

show the correct route for each Cable. Make sure the Cables are routed correctly, that the Pulleys move

smoothly and that the Cable Traps do not touch or bind the Cables. Incorrect cable routing can damage

the weight system.

Short Cable (9)

Long Cable (2)

Cable ID Chart

Attaching the Lat Bar, Row Bar or Handle to

the High Pulley Station

Attach the Lat Bar (76) to the Short Cable (9) with a

Cable Clip (73). For some exercises, the Chain (74)

should be attached between the Lat Bar and the Long

Cable with two Cable Clips. Adjust the length of the

Chain between the Lat Bar and the Long Cable so the

Lat Bar is in the correct starting position for the exer-

cise to be performed.

The Row Bar (70) or Handle (75) can be attached in the

same manner.

Attaching the Lat Bar, Row Bar or Handle to

the Low Pulley Station

Attach the Lat Bar (76) to the Long Cable (2) with a Cable

Clip (73). For some exercises, the Chain (74) should be

attached between the Lat Bar and the Short Cable with

two Cable Clips. Adjust the length of the Chain

between the Lat Bar and the Short Cable so the Lat

Bar is in the correct starting position for the exercise

to be performed.

The Row Bar (70) or Handle (75) can be attached in the

same manner.

Adjustment

The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise

poster accompanying this manual to see how the home gym system should be set up for each exercise.

IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments are in the cor-

rect starting position for the exercise to be performed. If there is any slack in the cables or chain as an

exercise is performed, the effectiveness of the exercise will be reduced.

Changing the Weight Setting

To change the setting of the weight stack, insert a Weight

Pin (39) under the desired Weight (26). Be sure to insert

the Weight Pin until the bent end of the Weight Pin is

touching the Weights. Then turn the bent end downward.

The setting of the weight stack can be changed from 6

pounds to 106 pounds, in increments of 12.5 pounds.

Note: Due to the cables and pulleys, the amount of

resistance at each exercise station may vary from the

weight setting. Use the WEIGHT RESISTANCE CHART

on page 18 to find the approximate amount of resis-

tance at each weight station.

Press Butterfly High Leg Low

Weight Arm Arm Pulley Lever Pulley

Plates (lbs.) (lbs.) (lbs.) (lbs.) (lbs.)

Top 12 46 19 21 15

1 40 70 33 37 33

2 62 97 49 54 45

3 86 110 68 68 59

4 94 141 81 88 72

5 127 162 96 100 87

6 150 180 110 109 102

7 160 199 128 120 113

8 193 212 142 140 131

This chart shows the approximate weight resistance at each station. ÒTopÓ refers to the 6 lbs. top

weight. The other numbers refer to the 12.5 lbs. weight plates. Note: The actual resistance at each

weight station may vary due to differences in individual weight plates, as well as friction between

the cables, pulleys, and weight guides.

Weight Resistance Chart

Tightening the Cables

Woven cable, the type of cable used on the home gym

system, can stretch slightly when it is first used. If there is

slack in the Cables before resistance is felt, the Cables

should be tightened.

To tighten the Cables, insert the Weight Pin (39, not

shown) between the third and the fourth Weight, counting

from the top. See ÒChanging the Weight SettingÓ on page

17 for instructions on moving the Weight Pin.

Loosen the 5/16Ó Plain Nut (32) holding the Eyebolt (44)

to the Leg Lever (29). Tighten the Eyebolt a couple of

turns until the Cables feel tighter. Tighten the Plain Nut to

prevent the Eyebolt from turning.

Additional slack can be removed by moving the ÒVÓ-Pulley

(6) to one of the other holes in the bracket (P) on the

Seat Frame (36). To do this, remove the 3/8Ó x 3 1/4Ó Bolt

(69), Cable Trap (66), 3/8Ó Flat Washer (55) and 3/8Ó

Nylon Locknut (63). Move the ÒVÓ-Pulley and re-attach it

with the Bolt, Washer, Cable Trap and Locknut.

Note: If a Cable tends to slip off the Pulleys often, the

Cable may have become twisted. Remove the Cable

and re-install it.

If the Cables need to be replaced, see ORDERING

REPLACEMENT PARTS on the back cover of this manual.

Trouble-shooting and Maintenance

Inspect and tighten all parts each time you use the home gym system. Replace any worn parts

immediately. The home gym system can be cleaned using a damp cloth and mild non-abrasive

detergent. Do not use solvents.

Exploded DrawingÑModel No. WESY81081

R0998A

Page is loading ...

Weider XP23 User manual

Brand: Weider

Model: XP23

Category: Fitness, gymnastics & weight training

Type: User manual

This manual is also suitable for

WESY81081

Download PDF

report

Weider XP23 User manual

This manual is also suitable for

Weider XP23 User manual

Related papers

Other documents