Black & Decker HD400 User manual

Brand: Black & Decker

Model: HD400

Category: Power drills

Type: User manual

Page is loading ...

””

((

))

½½

””

((

))

””

((

))

½½

””

((

))

ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

WARNING: READ INSTRUCTION MANUAL BEFORE USING PRODUCT.

MANUAL DE INSTRUCCIONES

INSTRUCTION MANUAL

CCaatt.. NN°° HHDD445500--HHDD550000--HHDD555500

Español 3

English 8

Page is loading ...

f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g. If devices are provided for the connection of dust extraction and collection facilities, ensure

these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power tool for your application. The correct power

tool will do the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the battery pack from the power tool before

making any adjustments, changing accessories, or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts

and any other condition that may affect the power tools operation. If damaged, have the power

tool repaired before use. Many accidents are caused by poorly maintained power tools.

f. Use the power tool, accessories and tool bits etc., in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualified repair person using only identical replacement

parts. This will ensure that the safety of the power tool is maintained.

6. Electrical Safety

Your tool is double insulated; therefore no earth wire is required. Always check that the main voltage

corresponds to the voltage on the rating plate.

Warning! If the power cord is damaged, it must be replaced by the manufacturer, authorized

Black & Decker Service Center or an equally qualified person in order to avoid damage or injury. If the

power cord is replaced by an equally qualified person, but not authorized by Black & Decker, the

warranty will not be valid.

7. Labels on Tool

The label on your tool may include the following symbols:

Read Instruction Manual

Use Eye Protection

Use Ear Protection

INTENDED USE

Your Black&Decker hammer drill has been designed for drilling in wood, metal, plastics, and masonry as well as for

screwdriving purposes. This tool is intended for consumer use only.

WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may

result in electric shock, fire and/or serious personal injury.

SAFETY INSTRUCTIONS

General power tool safety warnings

Warning! Read all safety warnings and all instructions. Failure to follow the warnings and

instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference. The term "power tool" in all of the warnings listed

below refers to your mains operated (corded) power tool or battery operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b. Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c. Keep children and bystanders away while operating a power tool. Distractions can cause you to

lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

b. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase

the risk of electric shock.

e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

NOTE: The term "Residual Curent Device (RCD)" can be replaced by "Ground Fault Circuit Interrupter

(GFCI)" or by "Earth Leakage Circuit Breaker (ELCB)".

3. Personal safety

a. Stay alert, watch what you are doing and use common sense when operating a power tool.

Do not use a power tool while you are tired or under the influence of drugs, alcohol or

medication. A moment of inattention while operating power tools may result in serious personal injury.

b. Use personal protective equipment. Always wear eye, ear and respiratory protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to

power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your

finger on the switch or energising power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

GENERAL SAFETY RULES

SAVE THESE INSTRUCTIONS

ENGLISH

V...............................Volts

A.............................. Amperes

Hz............................ Hertz

W..............................Watts

min...........................minutes

...........................Alternating current

...........................Direct current

............................. No load speed

...........................Class II Construction

...........................Earthing terminal

...........................Safety alert symbol

.../min...................... Revolutions or reciprocations

per minute

5) DRILLING: Make sure the material to be drilled is tightly fastened and when drilling thin materials use a wood

support. Always drill at a 90º angle and place enough pressure on the drill for the drill to perforate the surface

you are drilling. Never use excessive force when using your drill.

6) ACCESSORIES: Various accessories can fit your drill, allowing you to diversify its use.

7) SANDING / POLISHING: Position the disc as shown in the figure below. Place the rubber support in the chuck

and turn the chuck key clockwise to tighten the jaws to securely fasten the disc. To set the polishing feature

follow the example using the rubber disc and the spindle.

• When sanding, do not put all the pressure on the face of the disc; incline the disc at an angle on the surface.

FEATURES

This tool includes some or all of the following features.

1. Drill switch (only with specific models)

2. Chuck

3. On/off switch or variable switch

4. Lock-on button

5. Air ventilation

6. Variable Speed and Reverse switch

7. Side handle

USE

ON/OFF SWITCH

To switch your drill on, depress the on/off switch; your drill stops when the switch is released.

LOCK-ON BUTTON

• If continuous operation is required, press the lock-on button while the on/off switch is depressed.

• To stop when operation is continuos, depress the on/off switch again and release.

PERCUSSION SWITCH

This is a special feature in your drill that allows hitting and rotating at the same time.

a) DRILL MODE When drilling wood and metal. Useful for drilling projects only.

b) HAMMER MODE When drilling masonry, set the hammer switch in this mode.

c) VARIABLE SPEED Press the variable speed switch. The tool speed depends on how far you press the switch. As a

general rule, use low speeds for large diameter drill bits and high speeds for smaller diameter drill bits.

OPERATIONS

1) AS A GENERAL RULE. For large size drill bits use low speeds and for smaller drill bits use high speeds. On

variable speed drills, the more the trigger is pressed the faster the speed.

2) SET THE SPEED OF YOUR DRILL. Set the forward/reverse switch to the desired direction of rotation. Never

change the setting of the hammer switch, or the forward/reverse when your drill is in operation.

3) MAINTAIN VENTS CLEAR OF OBSTRUCTION. In order to maintain your tool from over heating and extend the life

of your tool, maintain the ventilation areas of your tool free from obstruction all the time.

4) HOW TO POSITION A DRILL BIT ON YOUR DRILL. Select the appropriate drill bit for the job (follow the guidelines

of the table below). First, make sure the drill is unplugged. Holding the rear section of the chuck, rotate the front

section until the jaws of the chuck are sufficiently open. Insert the drill bit in the jaws of the chuck. Hold the rear

section of the chuck while tightening the front. Turn the chuck key clockwise to tighten the jaws and securely

grip the drill bit. Use the chuck key in the 3 holes for better results.

ADDITIONAL SAFETY INSTRUCTIONS

FOR HAMMER DRILLS

DRILL BIT APPLICATION

• High Speed Steel

• Cabide Steel

• Tungesten Carbide

• Steel, Aluminium, all types of woods

• All types of wood

• Masonry, concrete, stone, brick, tile

marble, etc.

ENGLISH

WRONG

RIGHT

WRONG

RIGHT

• While sanding use horizontal and vertical movements. Avoid circular movements. Never sand on edges, this

may cause damage to sand paper as well as rubber disc.

DOUBLE INSULATION

The tool is double insulated. This means that all the external metal parts are electrically insulated from the main

power supply. This is done by placing insulation barriers between the electrical and mechanical components

making it necessary for the tool to be earthead (grounded).

NOTE: Double insulation does not take the place of normal safety precautions when operating the tool. The

insulation system is for added protection against injury resulting from a possible electrical insulation failure within

the tool.

EXTENSION CABLES - Up to 30m (100 ft.) of 3 core extension cable can be used with undue loss of power.

NOTE: An extension cable should not be used unless absolutely necessary. If the use of an extension cable is a

must, make sure it is properly wired, contains the correct rated fuse as recommended in its literature and is in

good electrical condition.

TECHNICAL DATA

The level of sound pressure of the tool is in accordance with U.L. legislation. It is recommended that you take

appropriate measures for the protection of your hearing if the sound level seems uncomfortable. The normally

equates to a sound pressure in excess of 85db (A).

ACCESSORIES

The performance of your tool depends on the accessory used. Black & Decker and Piranha accessories are

engineered to high quality standards and designed to enhance the performance of your tool. By using these

accessories you will get the very best from your tool.

MAINTENANCE

Your tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care and regular cleaning.

WARNING: Before performing any maintenance, switch off and unplug the tool.

• Regularly clean the ventilation slots in your tool using a soft brush or dry cloth.

• Regularly clean the motor housing using a damp cloth. Do not use any abrasive or solvent-based cleaner.

PROTECTING THE ENVIRONMENT

Separate collection.

This product must not be disposed of with normal household waste.

Should you find one day that your Black & Decker product needs replacement, or if it is of no further use to you, do

not dispose of it with household waste. Make this product available for separate collection.

WRONG

ENGLISH

Separate collection of used products and packaging allows materials to be recycled and used again.

Re-use of recycled materials helps prevent environmental pollution and reduces the demand for

raw materials.

Local regulations may provide for separate collection of electrical products from the household, at municipal waste

sites or by the retailer when you purchase a new product.

SERVICE INFORMATION

Black & Decker offers a full network of company-owned and authorized service locations. All Black & Decker

Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool

service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker

location nearest you.

SPECIFICATIONS

HD450 HD500 HD550

VOLTAGE

AR 220V ~ 50Hz 220V ~ 50Hz 220V ~ 50Hz

B2C 220V ~ 50Hz 220V ~ 50Hz 220V ~ 50Hz

B3 120V ~ 60Hz 120V ~ 60Hz 120V ~ 60Hz

POWER 500W 550W 550W

NO-LOAD SPEED 0-2800 rpm 0-2800 rpm 0-2800 rpm

Page is loading ...

Black & Decker HD400 User manual

Brand: Black & Decker

Model: HD400

Category: Power drills

Type: User manual

Download PDF

report

in other languages

español: Black & Decker HD400 Manual de usuario
português: Black & Decker HD400 Manual do usuário

Black & Decker HD400 User manual

Black & Decker HD400 User manual

in other languages

Related papers

Other documents