Electrolux EFC1060X User manual

Page is loading ...

We were thinking of you

when we made this product

electrolux 3

EN

DE

FR

IT

EMPFEHLUNGEN UND HINWEISE 6

CHARAKTERISTIKEN 7

MONTAGE 9

BEDIENUNG 12

WARTUNG 14

CONSEILS ET SUGGESTIONS 16

CARACTERISTIQUES TECHNIQUES 17

INSTALLATION 19

UTILISATION 22

ENTRETIEN ET NETTOYAGE 24

CONSIGLI E SUGGERIMENTI 26

CARATTERISTICHE 27

INSTALLAZIONE 29

USO 32

MANUTENZIONE 34

RECOMMENDATIONS AND SUGGESTIONS 36

CHARACTERISTICS 37

INSTALLATION 39

USE 42

MAINTENANCE 44

Page is loading ...

27 electrolux Caratteristiche

IT

CARATTERISTICHE

Ingombro

Page is loading ...

36 electrolux Recommendations and Suggestions

EN

Installation

• The manufacturer will not be held li-

able for any damages resulting from

incorrect or improper installation.

• The minimum safety distance be-

tween the cooker top and the extrac-

tor hood is 650 mm.

• Check that the mains voltage corre-

sponds to that indicated on the rating

plate ﬁ xed to the inside of the hood.

• For Class I appliances, check that the

domestic power supply guarantees

adequate earthing.

Connect the extractor to the exhaust

ﬂ ue through a pipe of minimum diam-

eter 120 mm. The route of the ﬂ ue

must be as short as possible.

• Do not connect the extractor hood to

exhaust ducts carrying combustion

fumes (boilers, ﬁ replaces, etc.).

• If the extractor is used in conjunction

with non-electrical appliances (e.g.

gas burning appliances), a sufﬁ cient

degree of aeration must be guaran-

teed in the room in order to prevent

the backﬂ ow of exhaust gas. The

kitchen must have an opening com-

municating directly with the open air in

order to guarantee the entry of clean

air.

Use

• The extractor hood has been de-

signed exclusively for domestic use to

eliminate kitchen smells.

• Never use the hood for purposes

other than for which it has ben de-

signed.

• Never leave high naked ﬂ ames under

the hood when it is in operation.

• Adjust the ﬂ ame intensity to direct it

onto the bottom of the pan only, mak-

ing sure that it does not engulf the

sides.

• Deep fat fryers must be continuously

monitored during use: overheated oil

can burst into ﬂ ames.

• Do not ﬂ ambè under the range hood;

risk of ﬁ re

• The hood should not be used by chil-

dren or persons not instructed in its

correct use.

Maintenance

• Switch off or unplug the appliance

from the mains supply before carrying

out any maintenance work.

• Clean and/or replace the Filters after

the speciﬁ ed time period.

• Clean the hood using a damp cloth

and a neutral liquid detergent.

The symbol on the product or on its

packaging indicates that this product may

not be treated as household waste. Instead

it shall be handed over to the applicable

collection point for the recycling of electrical

and electronic equipment. By ensuring this

product is disposed of correctly, you will help

prevent potential negative consequences for

the environment and human health, which

could otherwise be caused by inappropriate

waste handling of this product. For more

detailed information about recycling of this

product, please contact your local city ofﬁ ce,

your household waste disposal service or

the shop where you purchased the product.

RECOMMENDATIONS AND SUGGESTIONS

Characteristics electrolux 37

EN

Dimensions

CHARACTERISTICS

38 electrolux Characteristics

EN

Components

Ref. Q.ty Product Components

1 1 Hood Body, with: Controls, Light,

Blower, Filters

2 1 Telescopic Chimney:

2.1 1 Upper Section

2.2 1 Lower Section

9 1 Reducer Flange ø 150-120 mm

10 1 Damper

14.1 2 Air Outlet Connection Extension

15 1 Air Outlet Connection

Ref. Q.ty Installation Components

7.1 1 Hood Coupling Support

7.2.1 2 Upper Chimney Section Fixing

Brackets

7.3 1 Air Outlet Connection Support

7.4 1 Support Air Outlet Connection

Brackets

7.5 2 Safety Brackets

11 16 Plugs

12a 16 Screws 4.2 x 44.4

12c 8 Screws 2.9 x 9.5

12r 2 Screws 4.2 x 12.7

Q.ty Documentation

1 Instruction Manual

12a

11

7.1

2.1

2.2

2

9

14.1

15

12a

7.2.1

11

12r

12c

1

12a

11

7.5

10

7.3

7.4

Installation electrolux 39

EN

INSTALLATION

• Rest the Safety Brackets 7.5 as indi-

cated on the reference Horizontal line,

at a distance of 908 mm from the cor-

ner of the wall, checking that they are

level.

• Mark the centres of the Bores in the

Safety Brackets.

• Drill the points marked with a ø 8 mm

drill bit.

• Insert the plugs 11 into the holes.

• Fix the Brackets and the Support, us-

ing the Screws 12a (4.2 x 44.4) pro-

vided.

• In case of recycling version installa-

tion, you should ﬁ x the upper bracket

7.2.1, the holder 7.4, the bracket 7.3

to the holder 7.4 and the recycling

connector 15 to the bracket 7.3.

• Fasten 2 Screws 12r (4.2 x 12.7) pro-

vided into the Hood Canopy ﬁ xing

holes, positioned on the front plate of

the Hood Coupling Support, leaving a

space of 5-6 mm between the sup-

port and the head of the screw.

Wall drilling and bracket ﬁ xing

Wall marking:

• Rest the Bracket 7.2.1 as indicated

1-2 mm from the ceiling or top limit.

• Mark the centres of the Bores in the

Bracket.

• Rest the Bracket 7.2.1 as indicated X

mm under the ﬁ rst bracket (X = height

of the Top Chimney provided).

• Mark the centres of the Bores in the

Bracket.

• Rest the Hood Coupling Support 7.1

as indicated 1004 mm above the

Cooker Top, checking that the ﬁ xing

bores are equidistant from the corner

of the wall.

• Mark the centres of the Bores in the

Support.

• Drill the points marked with a ø 8 mm

drill bit.

• Insert the plugs 11 into the holes.

• Draw a Horizontal line on the Wall 668

mm above the Cooker Top.

1004

X

1÷2

7.2.1

7.1

668

11

12a

12r

908

7.5

12a

11

7.3

7.4

12a

11

40 electrolux Installation

EN

Hood body installation

• Before hooking up the Hood Canopy,

lock the 2 Screws Vr located at the

Hood Canopy connection points.

• Hook up the Hood Canopy to the

Screws 12r taking care to ensure that

the Safety brackets 7.5, ﬁ xed to the

wall, enter the Side Housings provided.

• Tighten the support Screws 12r until

they lock.

• Adjust Screws Vr to level the Hood

Canopy.

Connection in Ducting Version

When installing the ducting version, con-

nect the hood to the chimney using either

a ﬂ exible or rigid pipe ø 150 or 120 mm,

the choice of which is left to the installer.

To install a ø 150

• To install the dumper 10.

• Fix the pipe in position using sufﬁ cient

pipe clamps (not supplied).

To install a ø 120

• To install a ø 120 mm air exhaust con-

nection, insert the reducer ﬂ ange 9 on

the dumper 10.

• Fix the pipe in position using sufﬁ cient

pipe clamps (not supplied).

• Remove any activated charcoal ﬁ lters.

Connection in Recycling Version

• Insert the connection extension pieces

laterally 14.1 in connec-tion 15.

• Insert the Connector 15 into the Sup-

port bracket 7.3 and ﬁ x it with a screw.

• Make sure that the outlet of the exten-

sion pieces 14.1 is hori-zontally and ver-

tically aligned with the chimney outlets.

• Connect the air outlet connection 15 to

the hood body outlet using either a ﬂ ex-

ible or rigid pipe ø 150 mm, the choice

of which is left to the installer.

• Ensure that the activated charcoal ﬁ lters

have been inserted.

12r

Vr

7.5

ø 120

ø 150

10

9

ø 150

15

14.1

7.3

Installation electrolux 41

EN

Electrical Connection

• Connect the hood to the mains

through a two-pole switch having a

contact gap of at least 3 mm.

• Remove the grease ﬁ lters (see para-

graph Maintenance) being sure that

the connector of the feeding cable is

correctly inserted in the socket placed

on the side of the fan.

Chimney assembly

Upper Chimney

• Slightly widen the two sides of the

upper ﬂ ue and hook them behind the

brackets 7.2.1, making sure that they

are well seated.

• Secure the sides to the brackets us-

ing the 4 screws 12c (2,9 x 9,5) sup-

plied.

• Make sure that the outlet of the exten-

sions pieces is aligned with the chim-

ney outlets.

Lower exhaust ﬂ ue

• Slightly widen the two sides of the

ﬂ ue and hook them between the up-

per ﬂ ue and the wall, making sure that

they are well seated.

• Fix the lower part laterally to the hood

body using the 2 screws 12c (2,9 x

9,5) supplied.

7.2.1

2.1

2.2

2

12c

42 electrolux Use

EN

USE

The hood can be switched on pushing directly onto the requested speed without

ﬁ rstly having to select 0/1 button

Touch

control

Basic functions Indicator lights

Dual Function

L

When brieﬂ y pressed it switches the lighting

system on and off.

Touch control

unlit

Lights off

When pressed for 2 seconds it starts the

lighting system in “courtesy light” mode.

The lamps are fed at a reduced power of

approximately 5W. Such function can be

stopped by pressing the touch control for 2

seconds or just by pressing it shortly in order to

return to the normal lighting mode. In courtesy

light mode the touch control is not lit.

Touch control lit Lights on

Touch control

unlit

Courtesy light on

T1

When pressed the motor is stopped, regardless

of the speed it is set to.

Touch control lit Motor on

Touch control

unlit

Motor off

T2

When pressed the motor is set to the ﬁ rst speed

Touch control lit

T3

By a brief pressing the motor is set to the second

speed.

Touch control lit Second speed on

By pressing the touch control for approximately

2 seconds the Delay function is enabled, i.e

delayed shutdown of the appliance ensuring

a complete elimination of the residual odours.

This function can be activated at OFF-position

and at 1°, 2° and 3°speeds. It can be stopped

in advance by pressing any of the touch

controls (T) with the exception of T3. The Delay

function works according to the following

scheme:

1°speed / OFF = 20 minuets

2°speed = 15 minutes

3°speed = 5 minutes

Flashing touch

control

Delay function on

L T1 T2 T3 T4 T5 F

Use electrolux 43

EN

T4

When pressed the motor is set to the third speed Touch control lit

T5

When pressed the motor is set to the intensive

speed timed to 5 minutes. At the end of 5

minutes of intensive speed the hood starts again

at the speed it was set to previously. In case the

hood is set to the intensive speed directly from

OFF-state it will then start from the ﬁ rst speed

after 5 minutes of intensive speed.

Touch control lit

F

When pressed for 4 seconds it resets the ﬁ lter

alarm signal indicated by ﬂ ashing of the touch

control T1. This procedure can be carried out

only when the motor is stopped.

Touch control lit Metal grease ﬁ lters saturation

alarm. Metal grease ﬁ lters need

to be washed. The alarm starts

up after 100 working hours.

Flashing touch

control

Charcoal ﬁ lter saturation

alarm. Charcoal ﬁ lter has to

be replaced and metal grease

ﬁ lters washed. The alarm

starts up after 200 working

hours. (Activation; check the

paragraph “Charcoal ﬁ lter”)

44 electrolux Maintenance

EN

MAINTENANCE

Cleaning of the Metal Cassette

Filters

Alarm reset

• Stop the motor.

• Press the F -touch control for at least

4 seconds until the T1 -touch control

ﬂ ashes.

Cleaning the ﬁ lters

• The ﬁ lters must be cleaned every 2

months of operation, or more fre-

quently for particularly heavy usage,

and can be washed in a dishwasher.

• Remove the ﬁ lters one at a time hold-

ing them up with one hand and pulling

the handle downwards with the other

hand at the same time.

• Wash the ﬁ lters, taking care not to

bend them. Allow them to dry before

reﬁ tting.

• When reﬁ tting the ﬁ lters, make sure

that the handle is visible on the out-

side.

Maintenance electrolux 45

EN

Replacing the Charcoal Filter

This ﬁ lter cannot be washed or regene-

rated, and must be replaced when the F

touch control starts to ﬂ ash, or at least

once every 4 months. The alarm is only

triggered when the motor is on.

Enabling/Disabling the alarm signal

• In Recirculation Version Hoods, the

Filter saturation Alarm must be ena-

bled at the time of installation or later.

• Switch off the lights and the motor.

• Disconnect the mains power supply

to the hood by removing the motor

unit power supply cable connector,

switching off the power supply at the

Mains or turning the Main switch off.

• Restore the connection, pressing and

holding T2.

• Release the touch control, touch

controls L, T2 and F will light up nor-

mally.

• Within 3 seconds press the touch

control F until the key itself ﬂ ashes to

conﬁ rm as follows:

• 2 ﬂ ashes – Charcoal Filter saturation

Alarm ENABLED

• 1 ﬂ ash - Charcoal Filter saturation

Alarm DISABLED

Reset the alarm signal

• Stop the motor.

• Press the touch control F for at least

4 seconds, until the touch control T1

ﬂ ashes.

Replace the Filter

• Close the suction panel.

• Remove the metal grease ﬁ lters.

• Remove the saturated charcoal ﬁ lter,

turning the fasteners provided.

• Fit the new ﬁ lter and fasten it its cor-

rect position.

• Put the metal grease ﬁ lters in their

seats.

• Close the suction panel.

Light replacement

20 W halogen light.

• Remove the 2 screws ﬁ xing the Ligh-

ting support, and pull it out of from the

Hood.

• Extract the lamp from the Support.

• Replace with another of the same

type, making sure that the two pins

are properly inserted in the lamp hol-

der socket holes.

• Replace the Support, ﬁ xing it in place

with the two screws removed as abo-

ve.

Page is loading ...

www.electrolux.com

436004198_01 - 080414

Electrolux EFC1060X User manual

Electrolux EFC1060X User manual

in other languages

Related papers

Other documents