NAD C320BEE User manual

Page is loading ...

2

ENGLISH FRANÇAIS

DEUTSCH

NEDERLANDS

ESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

Warning: To reduce the risk of fire or electric shock, do not

expose this unit to rain or moisture.

The lightning flash with an arrowhead symbol within an equilateral

triangle, is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to

alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompanying

the product.

Do not place this unit on an unstable cart, stand or tripod, bracket

or table. The unit may fall, causing serious injury to a child or adult

and serious damage to the unit. Use only with a cart, stand, tripod,

bracket or table recommended by the manufacturer or sold with

the unit. Any mounting of the device on a wall or ceiling should

follow the manufacturer’s instructions and should use a mounting

accessory recommended by the manufacturer.

An appliance and cart combination should be moved with care.

Quick stops, excessive force and uneven surfaces may cause the

appliance and cart combination to overturn.

Read and follow all the safety and operating instructions before

connecting or using this unit. Retain this notice and the owner’s

manual for future reference.

All warnings on the unit and in its operating instructions should be

adhered to.

Do not use this unit near water; for example, near a bath tub,

washbowl, kitchen sink, laundry tub, in a wet basement or near a

swimming pool.

The unit should be installed so that its location or position does not

interfere with its proper ventilation. For example, it should not be

situated on a bed, sofa, rug or similar surface that may block the

ventilation openings; or placed in a built-in installation, such as a

bookcase or cabinet, that may impede the flow of air through its

ventilation openings.

The unit should be situated from heat sources such as radiators,

heat registers, stoves or other devices (including amplifiers) that

produce heat.

The unit should be connected to a power supply outlet only of the

voltage and frequency marked on its rear panel.

The power supply cord should be routed so that it is not likely to be

walked on or pinched, especially near the plug, convenience

receptacles, or where the cord exits from the unit.

Unplug the unit from the wall outlet before cleaning. Never use

benzine, thinner or other solvents for cleaning. Use only a soft

damp cloth.

The power supply cord of the unit should be unplugged from the

wall outlet when it is to be unused for a long period of time.

Care should be taken so that objects do not fall, and liquids are not

spilled into the enclosure through any openings.

This unit should be serviced by qualified service personnel when:

A. The power cord or the plug has been damaged; or

B. Objects have fallen, or liquid has been spilled into the unit; or

C. The unit has been exposed to rain or liquids of any kind; or

D. The unit does not appear to operate normally or exhibits a

marked change in performance; or

E. The device has been dropped or the enclosure damaged.

DO NOT ATTEMPT SERVICING OF THIS UNIT

YOURSELF. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL

Upon completion of any servicing or repairs, request the service

shop’s assurance that only Factory Authorized Replacement Parts

with the same characteristics as the original parts have been used,

and that the routine safety checks have been performed to

guarantee that the equipment is in safe operating condition.

REPLACEMENT WITH UNAUTHORIZED PARTS MAY RESULT IN FIRE,

ELECTRIC SHOCK OR OTHER HAZARDS.

ATTENTION

POUR ÉVITER LES CHOC ELECTRIQUES, INTRODUIRE LA

LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU

FOND.

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF

PLUG TO WIDE SLOT FULLY INSERT.

If an indoor antenna is used (either built into the set or installed

separately), never allow any part of the antenna to touch the metal

parts of other electrical appliances such as a lamp, TV set etc.

CAUTION

POWER LINES

Any outdoor antenna must be located away from all power lines.

OUTDOOR ANTENNA GROUNDING

If an outside antenna is connected to your tuner or tuner-

preamplifier, be sure the antenna system is grounded so as to

provide some protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code, ANSI/NFPA No.

70-1984, provides information with respect to proper grounding of

the mast and supporting structure, grounding of the lead-in wire to

an antenna discharge unit, size of grounding conductors, location of

antenna discharge unit, connection to grounding electrodes and

requirements for the grounding electrode.

a. Use No. 10 AWG (5.3mm2) copper, No. 8 AWG (8.4mm2)

aluminium, No. 17 AWG (1.0mm2) copper-clad steel or bronze

wire, or larger, as a ground wire.

b. Secure antenna lead-in and ground wires to house with stand-off

insulators spaced from 4-6 feet (1.22 - 1.83 m) apart.

c. Mount antenna discharge unit as close as possible to where lead-

in enters house.

d. Use jumper wire not smaller than No.6 AWG (13.3mm2) copper,

or the equivalent, when a separate antenna-grounding electrode

is used. see NEC Section 810-21 (j).

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL

CODE INSTRUCTIONS CONTAINED IN ARTICLE 810 - RADIO AND

TELEVISION EQUIPMENT.

NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to

call the CATV system installer’s attention to Article 820-40 of the

National Electrical Code that provides guidelines for proper

grounding and, in particular, specifies that the ground cable ground

shall be connected to the grounding system of the building, as close

to the point of cable entry as practical.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

ATTENTION:

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

C320BEE IM v2 29/8/02 11:02 pm Page 2

3

FRONT PANEL CONTROLS

REAR PANEL CONNECTIONS

ENGLISH

FRANÇAISDEUTSCHNEDERLANDSESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

NAD is a trademark of NAD Electronics International, a division of Lenbrook Industries Limited

C320BEE IM v2 29/8/02 11:02 pm Page 3

ENGLISH FRANÇAIS

DEUTSCH

NEDERLANDS

ESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

4

NOTES ON INSTALLATION

Your NAD C320BEE should be placed on a firm, level surface. Avoid

placing the unit in direct sunlight or near sources of heat and damp.

Allow adequate ventilation. Do not place the unit on a soft surface like

a carpet. Do not place it in an enclosed position such a bookcase or

cabinet that may impede the air-flow through the ventilation slots. Make

sure the unit is switched off before making any connections.

The RCA sockets on your NAD C320BEE are colour coded for

convenience. Red and white are Right and Left audio respectively.

Use high quality leads and sockets for optimum performance and

reliability. Ensure that leads and sockets are not damaged in any way and

all sockets are firmly pushed home.

For best performance, use quality speaker leads of 16 gauge (1.5mm)

thickness or more. If the unit is not going to be used for some time,

disconnect the plug from the AC socket.

Should water get into your NAD C320BEE, shut off the power to the

unit and remove the plug from the AC socket. Have the unit inspected

by a qualified service technician before attempting to use it again.

DO NOT REMOVE THE COVER, THERE ARE NO USER-

SERVICEABLE PARTS INSIDE.

Use a dry soft cloth to clean the unit. If necessary, lightly dampen the

cloth with soapy water. Do not use solutions containing benzol or other

volatile agents.

QUICK START

1 Connect the speakers to the rear Speaker terminals and sources to

the relevant rear input sockets.

2 Plug in the AC power cord.

3 Press the POWER button to turn the NAD C320BEE on.

4 Press the required input selector.

FRONT PANEL CONTROLS

1 Power - Pressing the Power switch turns the unit to standby state.

Upon selecting any input at the front panel or the ON button at the

remote, the C320BEE will choose the last selected as the active input.

The LED over the power switch will change form amber, indicating

standby state, to green when any input is selected. Pressing the

POWER switch again will turn the amplifier off.

NOTE

The remote control handset supplied with the C320BEE is of a

universal NAD type, designed to operate several NAD models. Some

buttons on this handset are inoperative, as the functions aren’t

supported by the C320BEE.

2 Power/Standby/Protection LED - Upon switching the power on,

the LED will light up amber in standby state. While one of the

input select buttons is pressed, the LED will turn red for a moment,

then turn green for ON state. In cases of serious abuse of the

amplifier, such as overheating, excessively low loudspeaker

impedance, short circuit etc. the amplifier will engage its Protection

circuitry, indicated by the LED turning from green to red, and the

sound being muted. In such a case, turn the amplifier off, wait for it

to cool down and/or check the speaker connections, making sure the

overall loudspeaker impedance doesn’t go below 4 ohms. Once the

cause for the protection circuitry to engage has been removed, press

Power again to resume normal operation.

3 Headphone socket - A 1/4” stereo jack socket is supplied for

headphone listening and will work with conventional headphones of

any impedance. Inserting a headphone jack into this socket

automatically switches off the loudspeakers. The volume, tone and

balance controls are operative for headphone listening. Use a

suitable adapter to connect headphones with other types of sockets,

such as 3.5mm stereo ‘personal stereo’ jack plugs.

NOTE

Make certain that the volume control is turned to minimum (fully

anti-clockwise) before connecting or disconnecting headphones.

Listening at high levels can damage your hearing.

4 Infra-red remote control command receiver - The infrared

sensor, located behind this circular window, receives commands from

the remote control. There must be a clear line-of-sight path from the

remote control to this window; if that path is obstructed, the remote

control may not work.

NOTE

Direct sunlight or very bright ambient lighting may affect the

operating range and angle for the remote control handset.

5 Input selectors These buttons select the active input to the NAD

C320BEE and the signal sent to the loudspeakers, the Tape outputs

and the PRE OUT sockets. The buttons on the remote control

handset duplicate these buttons, with the exception of the tuner

input; see below. Green LEDs just above each button will indicate

which input is currently selected.

DISC Selects a line-level source connected to the DISC sockets as the

active input.

CD Selects the CD (or other line-level source) connected to the CD

sockets as the active input.

VIDEO Selects the VCR (or stereo TV/Satellite/Cable receiver)

connected to the VIDEO sockets as the active input.

AUX Selects a line-level source connected to the AUX sockets as the

active input.

TUNER Selects the tuner (or other line-level source) connected to the

Tuner sockets as the active input. The remote control handset has

separate buttons for AM and FM; pressing either one will select the

C320BEE’s tuner input.

TAPE 2 Selects Tape 2 as the active input.

TAPE 1 Monitor Selects the output from a tape recorder when

playing back tapes or monitoring recordings being made through the

Tape 1 sockets. Press the Tape 1 button once to select it and again to

return to the normal input selection.

C320BEE IM v2 29/8/02 11:02 pm Page 4

ENGLISH

FRANÇAISDEUTSCHNEDERLANDSESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

5

Tape 1 is a tape Monitor function which does not override the current

input selection. For example, if the CD is the active input when TAPE

1 is selected, then the CD signal will continue to be selected and sent

to both the TAPE 2, and TAPE 1 OUTPUT sockets, but it is the sound

from recorder connected to Tape 1 that will be heard on the

loudspeakers. Apart from the amber LED to indicate Tape 1 is

engaged, the green LED for the active input will also stay lit.

NOTE

The remote control handset with the C320BEE supplied is of a

universal NAD type, designed to operate several NAD models. Some

buttons on this handset are inoperative as the functions aren’t

supported by the C320BEE. The Video 2 and Video 3 input selector

buttons on the remote control handset are inoperative in the case of

the C320BEE.

6 Soft clipping indicator - The green Soft Clipping LED shows that

the Soft Clipping mode is engaged. Refer also to “Rear Panel

Connections, Section 12 Soft Clipping” for more information.

7Tone controls - The NAD C320BEE is fitted with BASS and TREBLE

tone controls to adjust the tonal balance of your system.

The 12 o’clock position is ‘flat’ with no boost or cut, and an indent

indicates this position. Rotate the control clockwise to increase the

amount of Bass or Treble. Rotate the control anti-clockwise to

decrease the amount of Bass or Treble. The Tone controls do not

affect recordings made using the Tape outputs but will affect the

signal going to the Pre-amp output (Pre Out).

8Tone defeat - The TONE DEFEAT switch by-passes the tone control

section of the NAD C320BEE. If the Tone Controls are not normally

used and left in the 12 o’clock position, then it is advisable to switch

out the Tone Control section altogether by using this switch. In the

‘out’ position, the Tone Control circuits are active, pushing the TONE

DEFEAT switch ‘in’ bypasses the Tone Control section.

9 Balance - The BALANCE control adjusts the relative levels of the left

and right speakers. The 12 o’clock position provides equal level to

the left and right channels. A detent indicates this position.

Rotating the control clockwise moves the balance towards the right.

Rotating the control anti-clockwise moves the balance to the left.

The BALANCE control does not affect recordings made using the

Tape outputs but will affect the signal going to the Pre-amp output

(Pre Out).

10 Volume - The VOLUME control adjusts the overall loudness of the

signals being fed to the loudspeakers. It is motor driven and can be

adjusted from the remote control handset. The VOLUME control

does not affect recordings made using the Tape outputs but will

affect the signal going to the Pre-amp output (Pre Out).

On the remote control handset, press the MUTE button to

temporarily switch off the sound to the speakers and headphones.

Mute mode is indicated by the active input LED flashing. Press the

MUTE button again to restore sound. Mute does not affect

recordings made using the Tape outputs but will affect the signal

going to the Pre-amp output (Pre Out).

REAR PANEL CONNECTIONS

1 IR Input / output - This input is connected to the output of an IR

(infrared) repeater (Xantech or similar), or the IR output of another

component to allow control of the C320BEE from a remote location.

Ask your dealer or custom installer for further details.

2 Disc input - Input for additional line level input signals such as CD,

Mini Disc player or the output signal from a step-up amplifier for a

turntable. Use a twin RCA-to-RCA lead to connect the auxiliary unit’s

left and right ‘Audio Outputs’ to this input.

3CD input - Input for a CD or other line-level signal source. Use a twin

RCA-to-RCA lead to connect the CD player’s left and right ‘Audio

Outputs’ to this input. The NAD C320BEE only accepts analogue

signals from your CD player.

4Video input - Input for the audio signal from a stereo VCR (or stereo

TV/Satellite/Cable receiver) or other line-level audio source. Using

twin RCA-to-RCA leads, connect to the left and right ‘Audio

Outputs’ of the unit to these inputs. Note: These are audio inputs

only.

5 AUX input - Input for additional line level input signals such as

another CD player. Use a twin RCA-to-RCA lead to connect the

auxiliary unit’s left and right ‘Audio Outputs’ to this input.

6Tuner input - Input for a tuner or other line-level signal source. Use

a twin RCA-to-RCA lead to connect the tuner left and right ‘Audio

Outputs’ to this input.

7Tape 2 In/Out - Connections for analogue recording and playback

to an audio tape recorder of any type. Using twin RCA-to-RCA leads,

connect to the left and right ‘Audio Output’ of the tape machine to

the TAPE 2 IN sockets for playback and tape monitoring. Connect the

left and right ‘Audio Input’ of the tape machine to the TAPE 2 OUT

sockets for recording.

8Tape 1 In/Out - Connections for analogue recording and playback

to an audio tape recorder of any type. Using twin RCA-to-RCA leads,

connect to the left and right ‘Audio Output’ of the tape machine to

the TAPE 1 IN sockets for playback and tape monitoring. Connect the

left and right ‘Audio Input’ of the tape machine to the TAPE 1 OUT

sockets for recording.

9Pre out - Connections to an external power amplifier or processor,

such as a surround-sound decoder. In normal use these should be

connected to the Main-In sockets (No. 10) with the links supplied. To

connect your NAD C320BEE to external processor or amplifier

sections first remove these links. Use a twin RCA-to-RCA lead to

connect to the left and right ‘Audio Input’ of the Power amp or

processor to the Pre Out sockets.

NOTE

The Pre-Out output signal will be affected by the NAD C320BEE’s

volume and tone control settings, always turn the amplifier off

before connecting or disconnecting anything from to Pre-Out and

Main-In sockets.

C320BEE IM v2 29/8/02 11:02 pm Page 5

ENGLISH FRANÇAIS

DEUTSCH

NEDERLANDS

ESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

6

10 Main in - Connections to an external pre-amplifier or processor, such

as a surround-sound decoder. In normal use these should be

connected to the Pre-Out sockets (No. 9) with the links supplied. To

connect your NAD C320BEE to external processor or pre-amplifier

first remove these links. Use a twin RCA-to-RCA lead to connect to

the left and right ‘Audio Output’ of the pre-amp or processor to the

Main-In sockets.

NOTE

Always turn the amplifier off before connecting or disconnecting

anything from to Pre-Out and Main-In sockets.

11 Speakers - Speaker terminals for speakers with an impedance of 4

ohms or more. Connect the right speaker to the terminals market ‘R

+’ and ‘R-’ ensuring that the ‘R+’ is connected to the ‘+’ terminal on

your loudspeaker and the ‘R-’ is connected to the loudspeaker’s ‘-’

terminal. Connect the terminals marked ‘L+’ and ‘L-’ to the left

speaker in the same way.

Always use heavy duty (16 gauge; 1.5mm, or thicker) stranded wire

to connect loudspeakers to your NAD C320BEE. The high-current

binding post terminals can be used as a screw terminal for cables

terminating in spade or pin sockets or for cables with bare wire ends.

BARE WIRES AND PIN CONNECTORS

Bare wires and pin sockets should be inserted into the hole in the shaft

of the terminal. Unscrew the speaker terminal’s plastic bushing until the

hole in the screw shaft is revealed. Insert the pin or bare cable end into

the hole and secure the cable by tightening down the terminal’s

bushing. Ensure bare wire from the speaker cables does not touch the

back panel or another socket. Ensure that there is only 1/2” (1cm) of

bare cable or pin and no loose strands of speakers wire.

12 Soft Clipping™ - When an amplifier is driven beyond its specified

power output, a hard, distorted sound can be heard on very loud

sounds. This is caused by the amplifier cutting off or ‘hard clipping’

the peaks of sound that was not designed to reproduce. The NAD

Soft Clipping circuit gently limits the output of the system to

minimise audible distortion if the amplifier is overdriven.

If your listening involves moderate power levels you may leave the

Soft Clipping switch to Off. If you are likely to play at high levels, that

could stretch the amplifier’s power capability, then switch Soft

Clipping On.

The Soft Clipping™ LED on the front panel will illuminate when the

amplifier is in Soft Clipping mode.

13 AC line cord - Plug the AC power cord into a live AC wall socket.

Make sure all connections have been made before connecting to

mains.

14 12V trigger output - The 12V TRIGGER OUTPUT is used for

controlling external equipment that is equipped with a 12V trigger

input. This output will be 12V when the C320BEE is on and 0V when

the unit is either off or in standby. This output can drive a load up to

50mA at 12V.

TO MAKE A RECORDING

When any source is selected, its signal is also fed directly to any tape

machine connected to the TAPE 2 or TAPE 1 OUTPUTS for recording.

TAPE TO TAPE COPYING

You can copy between two tape machines connected to your NAD

C320BEE. Put the source tape in the recorder connected to Tape 2 and

the blank tape into the recorder connected to Tape 1. By selecting TAPE

2 Input you can now record from Tape 2 to Tape 1 and monitor the

signal coming from the original tape.

REMOTE CONTROL HANDSET

The Remote Control handset handles the key functions of the NAD

C320BEE and has additional controls to remotely operate NAD Tuners,

DVD, and CD machines. It will operate up to a distance of 16ft (5m).

Alkaline batteries are recommended for maximum operating life. Two

AAA (R 03) batteries should be fitted in the battery compartment at the

rear of the Remote Control handset. When replacing batteries, check

that they have been put in the right way round, as indicated on the base

of the battery compartment.

Please refer to previous sections of the manual for a full description of

individual functions.

NOTE

• The remote control handset supplied with the C320BEE is of

universal NAD type, designed to operate several NAD models. Some

buttons on this handset are inoperative, as the functions aren’t

supported by the C320BEE.

• The Video 2 and Video input selector, and Speakers A and Speakers

B buttons on the remote control handset are inoperative in the case

of the C320BEE.

• The input selector buttons perform the same functions as the

buttons labeled the same on the front panel. There are a few

differences and extra functions with the remote control handset

however.

TUNER AND TUNER MODE

Selects the Tuner input on the NAD C320BEE and toggles the AM or FM

waveband on a separate remote controllable NAD Tuner.

MUTE

Press the MUTE button to temporarily switch off the sound to the

speakers and headphones. Mute mode is indicated by the active input

LED flashing. Press the MUTE button again to restore sound.

Mute does not affect recordings made using the Tape outputs but will

affect the signal going to the Pre-amp output (Pre Out).

MASTER VOLUME

or respectively increases or decreases the Volume setting.

The motorized Volume Control on the front panel will indicate the level

set.

C320BEE IM v2 29/8/02 11:02 pm Page 6

ENGLISH

FRANÇAISDEUTSCHNEDERLANDSESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

7

Other than the commands relating to the NAD C320BEE amplifier itself,

there are other buttons, which will operate most NAD CD players and

Cassette decks equipped with IR link.

TUNER CONTROL

(for use with NAD Tuner)

Switch the small slider-switch to TUNER (at the base of the remote) to

control the numeric keypad 1 through +10

The TUNER button selects between AM and FM.

TUNE MODE in conjunction with or selects respectively

between number station preset and scanning for stations.

CD PLAYER CONTROL

(for use with NAD CD Player)

Switch the small slider-switch to CD (at the base of the remote) to

control the numeric keypad 1 through +10

engages Pause.

engages Stop.

engages Play or toggles between Play and Pause.

or engages Track skip; Press once to respectively go the next

track or to return to start of current or previous track.

NEXT DISC Go to next disc (for NAD CD changers).

NOTE

Direct sunlight or very bright ambient lighting may affect the

operating range and angle for the remote control handset.

1 Press inand lift tab to remove battery cover from recess

2 Place batteries into recess. Ensure that the alignment of the batteries

matches the ‘+’ and ‘-’ symbols on the casing.

3 Replace battery cover by aligning and inserting the two tabs into the

holes. Press battery cover into place until it clicks closed.

C320BEE IM v2 29/8/02 11:02 pm Page 7

ENGLISH FRANÇAIS

DEUTSCH

NEDERLANDS

ESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

8

PROBLEM CAUSE SOLUTION

NO SOUND

• Power AC lead unplugged or power not

switched on

• Check if AC lead is plugged in and power

switched on

•Tape 1 Monitor selected • De-select Tape 1 Monitor mode

• Mute on • Switch off Mute

• Rear Pre-out/Main-in amp links not fitted • Fit links

• Headphones inserted • Disconnect headphones

NO SOUND ONE CHANNEL

• Balance control not centered • Center Balance control

• Speaker not properly connected or damaged • Check connections and speakers

• Input lead disconnected or damaged • Check leads and connections

WEAK BASS / DIFFUSE STEREO IMAGE

• Speakers wired out of phase • Check connections to all speakers in the system

REMOTE CONTROL HANDSET

NOT WORKING

• Batteries flat, or incorrectly inserted • Check or replace batteries

• IR transmitter or receiver windows obstructed • Remove obstruction

• IR receiver in direct sun or very bright ambient

light

• Place unit away from direct sun, reduce amount

of ambient light

POWER/PROTECTION LED TURNS RED

DURING OPERATION

• Amplifier has overheated • Turn amplifier off, make sure ventilation slots on

top and bottom of amplifier are not blocked.

After amplifier has cooled down, turn back on

• Overall impedance of loudspeakers too low • Ensure the overall loudspeaker impedance is not

below 4 ohms

TROUBLESHOOTING

C320BEE IM v2 29/8/02 11:02 pm Page 8

9

SPECIFICATIONS

PRE-AMP SECTION

Line level inputs (Disc, CD, Video, Aux, Tuner, Tape1, Tape2)

Input impedance (R and C) 200kΩ + 320pF

Input sensitivity (ref. rated power) 220mV

Maximum input signal 6V

Signal / Noise ratio A-weighted

1

93.0dB ref. 1W

Signal / noise ratio pre-amp out, A-weighted 106dB ref. 500mV

Frequency response 20Hz - 20kHz <±0.1dB (Tone defeat on)

<±0.5dB (Tone defeat off)

THD + Noise, SMPTE IM < 0.01% at 5V out

Line level outputs

Output impedance Pre-out 80Ω

Tape Source Z + 1kΩ

Maximum output level Pre-out >12V

Tape >10V

Tone controls

Treble ±5dB at 10kHz

Bass ±8dB at 100Hz

IR / Trigger out

Input resistance >10kΩ

Input voltage Minimum 5V

Output resistance <30Ω

Output current 50mA

Output voltage 12V

POWER AMP SECTION

Continuous output power into 8Ω

2

50W (17dBW)

Rated distortion (THD 20Hz - 20kHz) 0.03%

Clipping power (maximum continuous power per channel 4Ω and 8Ω) 68W

IHF Dynamic headroom 8Ω +3.4dB

4Ω +5.0dB

IHF dynamic power (maximum short term power per channel) 8Ω 110W (20.4dBW)

4Ω 160W (22.0dBW)

2Ω 210W (23.2dBW)

Damping factor (ref. 8Ω, 1kHz) >160

Input impedance (R & C) 20kΩ + 470pF

Input sensitivity (rated output into 8Ω) 630mV

Voltage gain 29dB

Frequency response 20Hz - 20kHz 29dB

Signal/noise ratio, A-weighted ref. 1W 100dB

ref. 50W 117dB

THD + Noise

3

<0.03%

SMPTE IM

4

<0.01%

IHF IM

5

<0.01%

Headphone output impedance 220Ω

PHYSICAL SPECIFICATIONS

Dimensions (W x H x D) 435 x 100 x 290mm

Net weight 6.5kg (14.3lb)

Shipping weight 8kg (17.6lb)

1 From CD input to speakers output, volume setting for 500mV in, 8Ω 1W out

2 Minimum power per chnnel, 20Hz - 20kHz, both channels driven with no more than rated distiortion.

3 Total harmonic distortion, 20Hz - 20kHz from 250mW to rated output

4 Intermodulation distortion, 60Hz - 7kHz, 4:1, from 250mW to rated output

5 CCIF IM distortion, 19 + 20kHz rated output

Dimensions are of unit’s cabinet without attached feet; add up to 18mm for total height.

Dimension depth excludes terminals, sockets, controls and buttons.

ENGLISH

FRANÇAISDEUTSCHNEDERLANDSESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

C320BEE IM v2 29/8/02 11:02 pm Page 9

Page is loading ...

www.NADelectronics.com

A DIVISION OF LENBROOK INDUSTRIES LIMITED

C320BEE Manual 07/02

C320BEE IM v2 29/8/02 11:02 pm Page 46

NAD C320BEE User manual

NAD C320BEE User manual

in other languages

Related papers

Other documents