OWNER’S MANUAL
OMĆ6610 207 068A
May 2002
Running Gear/Cylinder Rack (770 187)
1. Parts Location And Assembly
WARNING
ELECTRIC SHOCK can kill.
• Do not touch live electrical parts.
• Turn Off welding power source and input disconnect
device.
• Disconnect input plug or power conductors from
deenergized supply BEFORE moving welding
power source.
CYLINDERS can explode if damaged.
• Keep cylinders away from welding and other
electrical circuits.
• Never touch cylinder with welding electrode.
• Always secure cylinder to running gear, wall, or
other stationary support.
FALLING EQUIPMENT can cause injury
and damage, OVERSIZED CYLINDER
can cause tipping.
• Move unit with proper handcart.
• If using a fork lift vehicle, secure unit on a skid.
• Never lift unit with cylinder attached.
• Maximum cylinder weight is 100 lb (45 kg).
Ref. 802 052 / Ref. 802 051-A
Tools Needed:
10 mm
Description (Qty)
Part
No.
Item
No.
1. 207 062 Handle/4 in Casters (1). .
2. 209 686 Caster, Swivel 4 in (2). . .
3. 207 059 Tray, Pan (1). . . . . . . . . . .
4. 207 058 Pan, Base (1). . . . . . . . . .
5. 189 045 Tray, Tool (1). . . . . . . . . .
6. 207 060 Support, Back (1). . . . . . .
7. 137 653 Label, Warning (1). . . . . .
8. 602 387 Chain, 28 in (1). . . . . . . . .
9. 189 046 Tray, Bottle (1). . . . . . . . .
10. 189 040 Axle (1). . . . . . . . . . . . . . .
11. 207 061 Wheel, 8 in (2). . . . . . . . .
206 803 Hardware Kit
(consisting of)
12. Nut, M6 (2). . . . . . . . . . . .
13. Screw, M6 x 15 mm (6). .
14. 602 250 Washer, Flat 21 mm (2). .
15. 121 614 Retaining Ring (2). . . . . .
16. Screw, M6 x 35 mm (4). .
17. Washer, Flat 6 mm (10). .
Be sure to provide Model when ordering
replacement parts.
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
17
13
17
13
17
2
OM-6610 Page 2
2. Assembly Instructions
Assemble Back Support (6) to
Base (4). Insert bent tabs into Base
slots. Push Back Support down to
snap side tabs into slots. Turn
assembly over, insert screwdriver
into each side slot, and bend each
tab toward outside of Base.
Assemble Bottle Tray (9) to Base
(4) using hardware kit items 13 and
17. Slide Axle (10) through holes in
Base and tighten hardware.
Slide Wheels (11) onto Axle (10),
install a Washer (14) onto each end
of Axle, and secure by using a
hammer to lightly tap Retaining
Ring (15) into slot at each end of
Axle.
Assemble Pan Tray (3) onto Base
(4) using hardware kit items 13 and
17.
Assemble Handle (1) to Pan Tray
(3) and Base (4) using hardware kit
items 16 and 17.
Be sure that all hardware is tight,
then place welding power source
onto cart.
Assemble Tool Tray (5) to Base (4),
and loosely install hardware kit
items 12, 13, and 17. Slide Tool Tray
(5) against front panel to secure
welding power source to cart. Tight-
en hardware.
Slide Chain (8) into slots in Back
Support (6).
. If using a small shielding gas
bottle, install Chain (8) into
slots in Bottle Tray (9).
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
17
13
17
13
17
Ref. 802 052
Bottom
View Of
Base
Back
Support
Tab
2
-
1
-
2
Miller RUNNING GEA Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Miller KF000000 Owner's manual
-
-
-
-
-
-
-
-
-
Other documents
-
HobartWelders RUNNING GEAR/CYLINDER RACK Owner's manual
-
Hobart Welding Products M-10 User manual
-
-
Hobart Welding Products IRONMAN 275 User manual
-
Hobart Welding Products IRONMAN 250 Owner's manual
-
Craftsman 917.252560 User manual
-
Croozer Cargo Handcart Kit Owner's manual
