DeWalt D51275K T 3 Owner's manual

Page is loading ...

2

Copyright DEWALT

Dansk 6

Deutsch 12

English 20

Español 26

Français 35

Italiano 40

Nederlands 47

Norsk 54

Português60

Suomi 67

Svenska 73

Türkçe

79

EÏÏËÓÈÎ· 86

D51256.P65 28-12-2001, 09:212

Page is loading ...

20

ENGLISH

NAILER D51256/D51275

Congratulations!

You have chosen a DEWALT tool. Years of

experience, thorough product development and

innovation make DEWALT one of the most reliable

partners for professional power tool users.

Technical data

D51256 D51275

Sound pressure (L

pA

) dB(A) < 82 < 82

Acoustic power (L

WA

) dB(A) < 95 < 95

Hand/arm weighted

vibration m/s

2

2.7 2.7

Recommended operating

pressure bar 4.9 - 8.3 4.9 - 8.3

Max. operating pressure bar 8.3 8.3

Air consumption per shot l 4.5 6.0

(at 6.9 bar) (at 6.9 bar)

Actuating mode contact contact

actuating actuating

Magazine angle 0° 34°

Fasteners

length mm 32 - 65 32 - 65

shank diameter mm 1.6 1.8

(16 gauge) (15 gauge)

angle 0° 34°

Weight kg 1.77 1.75

1)

This value is a tool-related characteristic value and

does not represent the influence to the hand-arm-

system when using the tool. The influence to the

hand-arm-system when using the tool will for example

depend on the gripping force, the contact pressure

force, the working direction, the adjustment of energy

supply, the workpiece and the workpiece support.

EC-Declaration of conformity

D51256/D51275

DEWALT declares that these tools have been designed

in compliance with:

98/37/EC, EN 792-13, EN 12549, EN 12096

For more information, please contact DEWALT at the

address below, or refer to the back of the manual.

Director Engineering and Product Development

Horst Großmann

DEWALT, Richard-Klinger-Straße 40,

D-65510, Idstein, Germany

Safety instructions

When using tools, always observe the safety

regulations applicable in your country to reduce

the risk of personal injury. Read the following

safety instructions before attempting to operate

this product.

Keep these instructions in a safe place!

General

1 Keep work area clean

Cluttered areas and benches can cause accidents.

2 Consider work area environment

Do not expose tools to humidity. Keep work area

well lit. Do not use tools in the presence of

flammable liquids or gases.

3 Keep children away

Do not let children or visitors come into contact

with the tool. Supervision is required for those

under 16 years of age.

4 Store idle tools

When not in use, tools must be stored in a dry

place and locked up securely, out of reach of

children.

5 Dress properly

Do not wear loose clothing or jewellery. They can

be caught in moving parts. Preferably wear

rubber gloves and non-slip footwear when

working outdoors. Wear protective hair covering

to keep long hair out of the way.

6 Do not overreach

Keep proper footing and balance at all times.

7 Stay alert

Watch what you are doing. Use common sense.

Do not operate the tool when you are tired.

D51256.P65 28-12-2001, 09:2120

21

ENGLISH

8 Use appropriate tool

The intended use is described in this instruction

manual. Do not force small tools or attachments

to do the job of a heavy-duty tool. The tool will

do the job better and safer at the rate for which it

was intended.

Warning! The use of any accessory or

attachment or performance of any operation with

this tool, other than those recommended in this

instruction manual may present a risk of personal

injury.

9 Maintain tools with care

Keep the tools in good condition and clean for

better and safer performance. Follow the

instructions for maintenance and changing

accessories. Keep all controls dry, clean and free

from oil and grease.

10 Check for damaged parts

Before using the tool, carefully check it for damage

to ensure that it will operate properly and perform

its intended function. Check for misalignment

and seizure of moving parts, breakage of parts

and any other conditions that may affect its

operation. Have damaged guards or other

defective parts repaired or replaced as instructed.

11 Have your tool repaired by an authorized

DEWALT repair agent

This tool is in accordance with the relevant safety

regulations. To avoid danger, tools must only be

repaired by qualified technicians.

Additional safety instructions for pneumatic nailers

• Always wear safety glasses.

• Always wear ear protection.

• Only use fasteners of the type specified in

the manual.

• Do not use any stands for mounting the tool to

a support.

• Never use the tool for any other purpose than

specified in this manual.

• Prior to each operation check that the safety and

triggering mechanism is functioning properly and

that all nuts and bolts are tight.

• Use quick-action couplings for connection to the

compressed air system. The non-sealable nipple

must be fitted to the tool in such a way that no

compressed air remains in the tool after

disconnection.

• Always use clean, dry compressed air.

Do not use oxygen or combustible gases as an

energy source for this tool.

• Only connect this tool to an air supply where the

maximum allowable pressure of the tool cannot

be exceeded by more than 10%. In case of

higher pressures, a pressure reducing valve

including a downstream safety valve shall be built

into the compressed air supply.

• Only use hoses with a rating exceeding the

maximum operating pressure of the tool.

• Before transporting the tool, disconnect it from

the compressed air system, especially where

ladders are used or where unusual physical

posture is adopted while moving.

• Disconnect the tool from the air supply when it is

not in use.

• Avoid weakening or damaging the tool,

for example by:

- punching or engraving

- modifications not authorised by the manufacturer

- guiding against templates made of hard

material such as steel

- dropping or pushing across the floor

- applying excessive force of any kind

• Do not use the equipment as a hammer.

• Never point any operational fastener driving tool

at yourself or at any other person.

• While working, hold the tool in such a way that

no injuries can be caused to the head or to the

body in the event of a possible recoil due to a

disruption in the energy supply or hard areas

within the workpiece.

• Never actuate the fastener driving tool into free

space.

• In the work area, carry the tool at the workplace

using only one handle, and never with the trigger

actuated.

• Consider the conditions in the work area.

Fasteners can penetrate thin workpieces or slip

off corners and edges of the workpiece, and thus

put people at risk.

• Do not drive fasteners close to the edge of the

workpiece.

• Do not drive fasteners on top of other fasteners.

• Only use spare parts specified by the

manufacturer or his authorised agents.

D51256.P65 28-12-2001, 09:2121

22

ENGLISH

• Have repairs carried out only by the manufacturer

or authorised agents having due regard to the

information given in the manual and using the

appropriate tools and equipment.

• Do not disassemble or block any parts of the

fastener driving tool such as the safety yoke.

• Have the tool serviced properly and at regular

intervals.

The following pictograms are shown on the tool:

Pneumatic tool with safety yoke.

Do not use on a ladder.

Magazine angle.

Maximum number of nails in magazine.

Nail diameter.

Nail length.

Max. operating pressure.

Package contents

The package contains:

1 Nailer

1 Sequential action trigger

1 Pair of safety glasses

1 Bottle of DEWALT pneumatic tool oil

2 Allen keys

1 Kitbox

1 Instruction manual

1 Exploded drawing

• Check for damage to the tool, parts or accessories

which may have occurred during transport.

• Take the time to thoroughly read and understand

this manual prior to operation.

Description (fig. A)

Your nailer D51256/D51275 has been designed for

driving fasteners into wooden workpieces.

1 Trigger/lock-off switch

2 Air fitting

3 Contact trip

4 Magazine

Assembly and adjustment

Trigger selection

These tools are assembled with a bump action

trigger. A sequential action trigger is also included

with the original packaging. For definitions of “bump

action” and “sequential action”, see below.

- The grey trigger with a single nail printed on the

side is the sequential action trigger. Installation of

this kit causes the tool to function in sequential

action mode.

- The black trigger with three nails printed on the

side is the bump action trigger. Installation of this

kit causes the tool to function in bump action

mode.

Removing the trigger (fig. B)

• Disconnect the airline from the tool.

• Remove all nails from the magazine.

• Remove the rubber grommet (5) from the end of

the dowel pin (6).

• Remove the dowel pin.

• Remove the trigger assembly (7).

Fitting the trigger (fig. B)

• Select the appropriate trigger.

• Insert the trigger assembly into the trigger cavity,

ensuring that the trigger spring (8) is properly

seated.

• Insert the dowel pin (6) through the tool frame,

contact trip guide and trigger assembly.

• Push the rubber grommet (5) onto the end of the

dowel pin.

Air fitting (fig. A)

These tools have a standard 1/4" pipe thread for

the air fitting (2).

• Wrap the male end of the fitting with Teflon tape

to prevent air leaks.

• Screw the fitting into the end cap and tighten firmly.

D51256.P65 28-12-2001, 09:2122

23

ENGLISH

Instructions for use

Always observe the safety instructions

and applicable regulations.

Preparing the tool (fig. C)

• Drain all condensation from the air compressor

tanks and hoses.

• Lubricate the tool. See “Maintenance”.

• Remove all nails from the magazine.

• Lock the nail pusher (11) in the back position.

• Check if the contact trip (3) and nail pusher (11)

can move freely.

Do not use the tool if the contact trip or

nail pusher cannot move freely.

• Check that the pressure of the air supply is below

the maximum recommended operating pressure.

• Connect the air hose to the fitting on the tool.

• Check for audible leaks around valves and gaskets.

Never use a tool that leaks or has

damaged parts.

Cold weather operation

When operating tools at temperatures below freezing:

• Keep the tool as warm as possible before use.

• Disconnect the airline from the tool.

• Put 5-10 drops of DEWALT pneumatic tool oil (or

winter-weight pneumatic oil containing ethylene

glycol) into the air inlet.

• Set the air pressure to a maximum of 5.5 bar.

• Connect the air hose to the fitting on the tool.

• Load nails into the magazine as described below.

• Actuate the tool 5 or 6 times into scrap lumber to

lubricate the o-rings.

• Increase the air pressure to the normal operating

level.

• Use the tool in the normal manner.

Hot weather operation

The tool should operate normally. Avoid the heat of

direct sunlight to avoid damage to the bumpers,

o-rings, and other rubber parts.

Loading the tool (fig. C)

These tools are equipped with a dual-load

magazine.

Always connect the tool to the air supply

before loading nails.

• Select an appropriate collated nail stick. See

“Technical data”.

• Load the magazine using one of the following

methods:

Loading and locking

• Insert collated nail stick (s) into the loading slot in

the rear of the magazine.

• Pull the nail pusher (11) rearward to fall behind

the nails.

Locking and loading

• Lock the nail pusher (11) in the back position.

• Insert collated nail stick (s) into the loading slot in

the rear of the magazine.

• Unlatch the nail pusher by pushing forward and

carefully slide the nail pusher forward to press

against the nails.

Actuating the tool (fig. D)

These tools are equipped with a trigger/lock-off

switch (1). When rotated to the right, this switch

prevents the tool from actuating.

When the switch is centred, the tool will be fully

operational. The tool can be operated using one of

two modes: sequential action mode or bump action

mode. The trigger installed on the tool determines

the mode of actuation.

Sequential action mode

The sequential action mode is used for intermittent

nailing when very careful and accurate placement is

desired.

• Fit the grey trigger as described above.

• Push the contact trip against the work surface.

• Pull the trigger to actuate the tool. Each trigger

pull with the contact trip pushed against the work

surface will drive one nail.

Bump action

The bump action mode is used for rapid nailing on

flat, stationary surfaces.

• Fit the black trigger as described above.

• To drive a single nail: Operate the tool as

described for sequential action.

D51256.P65 28-12-2001, 09:2123

24

ENGLISH

• To drive several nails: Pull the trigger first, and

then push the contact trip repeatedly against the

work surface.

Do not keep the trigger depressed when

the tool is not in use. Keep the trigger

lock-off switch rotated to the right to

prevent accidental actuation when the

tool is not in use.

Clearing a jammed nail (fig. E)

If a nail becomes jammed in the nosepiece, follow

these instructions to remove the nail:

• Disconnect the airline from the tool.

• Lock the trigger with the trigger lock-off switch.

• Lock the nail pusher (11) in the back position.

• Flip up the front latch (12) and move the bracket

(13) out of the way so that barrel (14) can be

opened.

• Remove the bent nail, using pliers if necessary.

• If the driver blade is in the down position, push

the driver blade upward using a screwdriver.

• Close the barrel (14) and put the bracket (13)

back in position.

• Press the front latch (12) into the locked position.

• Connect the air hose to the fitting on the tool.

• Load nails into the magazine. See “Loading the

tool”.

• Unlatch the nail pusher by pushing forward and

carefully slide the nail pusher forward to press

against the nails.

If nails become jammed in the nosepiece

frequently, have the tool serviced by an

authorised DEWALT service centre.

Depth setting (fig. F)

Always disconnect the tool from the air

supply before adjusting the depth setting.

The depth that the nails are driven can be adjusted

using the depth adjustment on the nosepiece of

the tool.

• To reduce the depth, press the adjustment

button (15) and slide the slider switch (16)

downward.

• To increase the depth, press the adjustment

button (15) and slide the slider switch (16)

upward.

Belt/rafter hook

These tools have an integrated belt/rafter hook.

The hook can be rotated to either side of the tool

and can be folded out of the way when not in use.

To remove the belt/rafter hook:

• Remove the air hose from the fitting on the tool.

• Use pliers or a wrench to remove the nut for the

belt/rafter hook from the end cap of the tool.

• Remove the belt/rafter hook, washer and detent

spring.

Maintenance

Your DEWALT tool has been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends on proper tool care and regular cleaning.

Perform the following maintenance operations every

day:

Lubricate tool with 5-7 drops of DEWALT

pneumatic tool oil

• Insert drops into the air fitting on the end cap of

the tool.

Drain all condensation from the air compressor

tanks and hoses

• Open petcocks or other drain valves on the

compressor tanks.

• Allow any accumulated water to drain from hoses.

Clean magazine, pusher, and contact trip

mechanism

• Clean by blowing with compressed air.

Ensure that all fasteners on the tool are tight and

undamaged

• Tighten loose fasteners using the appropriate tool.

D51256.P65 28-12-2001, 09:2124

25

ENGLISH

Troubleshooting

If your tool seems not to operate properly, follow the

instructions below. If this does not solve the

problem, please contact your repair agent.

Tool does not work

• Check the air supply.

• If the temperature is low, warm the tool up.

Tool has insufficient power

• Check the air supply.

• Check if the air exhaust is clear.

• Lubricate the tool.

Top cap leaks air

• Tighten the cap screws.

Tool skips nails

• Check the air supply.

• Lubricate the tool.

• Clean the magazine and nosepiece.

Fasteners jam in tool

• Make sure only to use fasteners of the type

specified.

• Tighten the nosepiece screws.

Unwanted tools and the environment

Take your tool to an authorized DEWALT repair agent

where it will be disposed of in an environmentally

safe way.

GUARANTEE

• 30 DAY NO RISK SATISFACTION GUARANTEE •

If you are not completely satisfied with the

performance of your DEWALT tool, simply return

it within 30 days, complete as purchased, to the

point of purchase, for a full refund or exchange.

Proof of purchase must be produced.

• ONE YEAR FREE SERVICE CONTRACT •

If you need maintenance or service for your

DEWALT tool, in the 12 months following

purchase, it will be undertaken free of charge at

an authorized DEWALT repair agent. Proof of

purchase must be produced. Includes labour and

spare parts for Power Tools. Excludes accessories.

• ONE YEAR FULL WARRANTY •

If your DEWALT product becomes defective due

to faulty materials or workmanship within

12 months from the date of purchase, we

guarantee to replace all defective parts free of

charge or, at our discretion, replace the unit free

of charge provided that:

• The product has not been misused.

• Repairs have not been attempted by

unauthorized persons.

• Proof of purchase date is produced.

This guarantee is offered as an extra benefit

and is additional to consumers statutory rights.

For the location of your nearest authorized

DEWALT repair agent, please use the appropriate

telephone number on the back of this manual.

Alternatively, a list of authorized DEWALT repair

agents and full details on our after-sales service

are available on the Internet at www.2helpU.com.

D51256.P65 28-12-2001, 09:2125

Page is loading ...

93

E°°À∏™∏

• 30 ∏ªEƒø¡ E°°À∏™∏ π∫∞¡√¶√π∏∆π∫∏™

∞¶√¢√™∏™ •

E¿Ó ‰ÂÓ Â›ÛÙÂ Ï‹Úˆ˜ ÈÎ·ÓÔÔÈËÌ¤ÓÔÈ ·ﬁ ÙËÓ

·ﬁ‰ÔÛË ÙÔ˘ ÂÚÁ·ÏÂ›Ô˘ Û·˜ DEWALT, ·ÏÒ˜

ÂÈÛÙÚ¤„ÙÂ ÙÔ ÂÓÙﬁ˜ 30 ËÌÂÚÒÓ, Ï‹ÚÂ˜

ﬁˆ˜ ÙÔ ·ÁÔÚ¿Û·ÙÂ, ·ﬁ ÙÔ ÂÍÔ˘ÛÈÔ‰ÔÙËÌ¤ÓÔ

∫·Ù¿ÛÙËÌ· DEWALT, ÁÈ· Ï‹ÚË ÂÈÛÙÚÔÊ‹

¯ÚËÌ¿ÙˆÓ. ¶Ú¤ÂÈ Ó· ÚÔÛÎÔÌÈÛÙÂ› ·ﬁ‰ÂÈÍË

·ÁÔÚ¿˜.

• E¡√™ E∆√À™ ™Àªµ√§∞π√ °π∞ ¶§∏ƒE™ ™Eƒµπ™ •

E¿Ó ¯ÚÂÈ¿˙ÂÛÙÂ Û˘ÓÙ‹ÚËÛË ‹ Û¤Ú‚È˜ ÁÈ· ÙÔ

ÂÚÁ·ÏÂ›Ô Û·˜ DEWALT, ÂÓÙﬁ˜ 12 ÌËÓÒÓ ·ﬁ

ÙËÓ ·ÁÔÚ¿, ·˘Ùﬁ ÌÔÚÂ› Ó· Á›ÓÂÈ ‰ˆÚÂ¿Ó ÛÂ

ÂÍÔ˘ÛÈÔ‰ÔÙËÌ¤ÓÔ ∫·Ù¿ÛÙËÌ· Service.

¶Ú¤ÂÈ Ó· ÚÔÛÎÔÌÈÛÙÂ› ·ﬁ‰ÂÈÍË ·ÁÔÚ¿˜.

∏ Û˘ÓÙ‹ÚËÛË/service ÂÚÈÏ·Ì‚¿ÓÂÈ ÂÚÁ·Û›·

Î·È ·ÓÙ·ÏÏ·ÎÙÈÎ¿ ÁÈ· Ù· ËÏÂÎÙÚÈÎ¿ ÂÚÁ·ÏÂ›·

DEWALT.

• E¡√™ E∆√À™ ¶§∏ƒ∏™ E°°À∏™∏ •

E¿Ó ÙÔ ÚÔ˚ﬁÓ Û·˜ ÙË˜ DEWALT ·ÚÔ˘ÛÈ¿˙ÂÈ

·ÓˆÌ·Ï›· ÔÊÂÈÏﬁÌÂÓË ÛÂ ÂÏ¿ÙÙˆÌ· ÙˆÓ

˘ÏÈÎÒÓ ‹ ÙË˜ Î·Ù·ÛÎÂ˘‹˜ ÂÓÙﬁ˜ 12 ÌËÓÒÓ ·ﬁ

ÙËÓ ËÌÂÚÔÌËÓ›· ÙË˜ ·ÁÔÚ¿˜, ÂÁÁ˘ÒÌ·ÛÙÂ ÙË

‰ˆÚÂ¿Ó ·ÓÙÈÎ·Ù¿ÛÙ·ÛË ﬁÏˆÓ ÙˆÓ

ÂÏ·ÙÙˆÌ·ÙÈÎÒÓ ÌÂÚÒÓ, ‹ Î·Ù¿ ÙËÓ ÎÚ›ÛË Ì·˜,

ÙË ‰ˆÚÂ¿Ó ·ÓÙÈÎ·Ù¿ÛÙ·ÛË ÔÏﬁÎÏËÚË˜ ÙË˜

ÌÔÓ¿‰·˜ ˘ﬁ ÙËÓ ÚÔ¸ﬁıÂÛË ﬁÙÈ:

• ¢ÂÓ ¤¯ÂÈ Á›ÓÂÈ Î·Î‹ ÌÂÙ·¯Â›ÚÈÛË ÙÔ˘

ÚÔ˚ﬁÓÙÔ˜.

• ¢ÂÓ ¤¯ÂÈ ÂÈ¯ÂÈÚËıÂ› ÂÈÛÎÂ˘‹ ·ﬁ ÌË

ÂÍÔ˘ÛÈÔ‰ÔÙËÌ¤ÓÔ ¿ÙÔÌÔ.

• £· ÚÔÛÎÔÌÈÛÙÂ› ·ﬁ‰ÂÈÍË ÙË˜ ËÌÂÚÔÌËÓ›·˜

·ÁÔÚ¿˜.

°È· Ó· ÂÓÙÔ›ÛÂÙÂ ÙÔ ÏËÛÈ¤ÛÙÂÚÔ

ÂÍÔ˘ÛÈÔ‰ÔÙËÌ¤ÓÔ ∫·Ù¿ÛÙËÌ· Service,

·Ú·Î·ÏÂ›ÛıÂ Ó· ÙËÏÂÊˆÓ‹ÛÂÙÂ ÛÙÔ

ÏËÛÈ¤ÛÙÂÚÔ ∫·Ù¿ÛÙËÌ· Service ÙË˜ ÂÙ·ÈÚ›·˜

Ì·˜ (‚Ï¤Â ·Ú·Î¿Ùˆ). EÓ·ÏÏ·ÎÙÈÎ¿, ÌÈ· Ï›ÛÙ·

ÂÍÔ˘ÛÈÔ‰ÔÙËÌ¤ÓˆÓ ∫·Ù¿ÛÙËÌ·ÙˆÓ Service

DEWALT Î·È ÔÏÏ¤˜ ÏÂÙÔÌ¤ÚÂÈÂ˜ Û¯ÂÙÈÎ¿ ÌÂ

ÙËÓ ˘ËÚÂÛ›· after-sales Â›Ó·È ‰È·ı¤ÛÈÌÂ˜ ÛÙÔ

Internet ÛÙË ‰ÈÂ‡ı˘ÓÛË www.2helpU.com.

∂§§∏¡π∫∞

D51256.P65 28-12-2001, 09:2593

Page is loading ...

96

Belgique et Luxembourg DEWALT Tel: 02 719 07 11

België en Luxemburg Weihoek 1, Nossegem Fax: 02 721 40 45

1930 Zaventem-Zuid www.dewaltbenelux.com

Danmark DEWALT Tlf: 70 20 15 30

Hejrevang 26 B Fax: 48 14 13 99

3450 Allerød www.dewalt-nordic.com

Deutschland DEWALT Tel: 06126-21-1

Richard-Klinger-Straße Fax: 06126-21-2770

65510 Idstein www.dewalt.de

EÏÏ¿˜ Black & Decker (Hellas) S.A. TËÏ: (01) 8981-616

™ÙÚ¿‚ˆÓÔ˜ 7 & µÔ˘ÏÈ·ÁÌ¤ÓË˜ 159 º·Í: (01) 8983-570

°Ï˘Ê¿‰· 16674, ∞ı‹Ó· Service: (01) 8982-630

España D

EWALT Tel: 934 797 400

Parque de Negocios “Mas Blau” Fax: 934 797 439

Edificio Muntadas, c/Bergadá, 1, Of. A6

08820 El Prat de Llobregat (Barcelona)

France D

EWALT Tel: 472 20 39 72

Le Paisy Fax: 472 20 39 02

BP 21, 69571 Dardilly Cedex

Helvetia D

EWALT ROFO Kundendienst Tel: 026 - 674 93 93

Schweiz Gewerbezone Seeblick Fax: 026 - 674 93 94

3213 Kleinbösingen www.dewalt.ch

Ireland DEWALT Tel: 00353-2781800

Calpe House Rock Hill Fax: 00353-2781811

Black Rock, Co. Dublin

Italia DEWALT Tel: 0800-014353

Viale Elvezia 2 Fax: 039-2387592

20052 Monza (Mi)

Nederland DEWALT Tel: 076 50 02 000

Florijnstraat 10 Fax: 076 50 38 184

4879 AH Etten-Leur www.dewalt.benelux.com

Norge D

EWALT Tel: 22 99 99 00

Strømsveien 344 Fax: 22 99 99 01

1011 Oslo www.dewalt-nordic.com

Österreich D

EWALT Tel: 01 - 66116 - 0

Werkzeugevertriebs GmbH Fax: 01 - 66116 - 14

Erlaaerstraße 165, Postfach 320,1231 Wien www.dewalt.at

Portugal DEWALT Tel: 214 66 75 00

Rua Egas Moniz 173 Fax: 214 66 75 75

João do Estoril, 2766-651 Estoril

Suomi DEWALT Puh: 98 25

45

40

Palotie 3 Fax: 98 25 45 444

01610 Vantaa www.dewalt-nordic.com

Brandvägen 3 Tel: 98 25

45

40

01610 Vanda Fax: 98 25 45 444

www.dewalt-nordic.com

Sverige D

EWALT Tel: 031 68 61 00

Box 603 Fax: 031 68 60 08

421 26 Västra Frölunda, Besöksadr. Ekonomivägen 11 www.dewalt-nordic.com

Türkiye

DEWALT

Tel: 021 26 39 06 26

Merkez Mahallesi, Köyaltı Mevkii, Şahnur Sokak Faks: 021 26 39 06 35

(OTTO Binası) 34530 Yenibosna/İstanbul (PBX)

United Kingdom DEWALT Tel: 01753-56 70 55

210 Bath Road Fax: 01753-57 21 12

Slough, Berks SL1 3YD

609121-00

D51256.P65 28-12-2001, 09:2596

DeWalt D51275K T 3 Owner's manual

This manual is also suitable for

DeWalt D51275K T 3 Owner's manual

in other languages

Related papers

Other documents