ANTAIRA Dual Channel Gigabit Ethernet PCIe Card Installation guide

Brand
ANTAIRA
Model
Dual Channel Gigabit Ethernet PCIe Card
Category
Interface cards/adapters
Type
Installation guide
1
Thank you for purchasing this Dual Channel Gigabit Ethernet PCI
Express Card. It is the fastest LAN host adapter available in the market
that is specially designed to connect dual channel gigabit LAN
interface to any computer with PCIe (PCI Express) slots. It supports
crossover detection and auto-correction feature for the easy network
cabling.
Features:
Fully PCI Express Base Specifications 1.1 Compliant
Dual Gigabit (10/100/1000Mbps) Ethernet Ports over a PCIe Switch
Supports Full Duplex Flow Control (IEEE 802.3x)
Fully Compliant with IEEE 802.3 IEEE 802.3u, IEEE 802.3ab
Supports IEEE 802.1Q VLAN tagging, Crossover Detection &
Auto-Correction
Power Down and Link Down Power Saving
Microsoft NDIS5 Checksum Offload (IP, TCP, UDP) and Large send
Offload Support
Dual Channel Gigabit Ethernet PCIe Card
Installation Guide
1. Introduction
2. Board and Bracket Layout
LINK LEDs
(Green)
Activity LEDs
(Yellow)
RJ45 Connectors: CH2 CH1
Short bracket will be
assembled if the low
profile model is shipped
Dual Channel Gigabit Ethernet PCIe Card
2
Due to the hot-plug feature of the PCI Express, the installation of the
PCIe Dual Channel Gigabit Ethernet card is quite straightforward.
1. Turn the system power OFF before installation!
2. Use static electricity discharge precautions. To avoid damaging
any components on the card, handle it by edges.
3. Remove the chassis cover from your computer
4.
Locate an unused PCI Express slot (typically white and smaller)
and remove the corresponding slot cover from computer chassis.
5.
Plug the Dual Channel Ethernet PCIe card to the unused PCI
Express expansion slot and attached the I/O card bracket to the
computer chassis screw.
6.
Put the chassis cover back on the computer.
7.
Turn ON the power of your computer and peripherals.
8.
Proceed with Software Driver Installation.
9.
Installing LAN cables
Connect the LAN cables to both RJ45 connectors of the Dual
Channel Ethernet PCIe card. The ‘LINK’ LEDs will light if link on.
However, the ‘ACT’ LEDs will flash when transferring data.
3. Installing the Gigabit Ethernet PCIe Card
Dual Channel Gigabit Ethernet PCIe Card
3
The Gigabit Ethernet drivers are shipped in the following folder of the
driver CD.
Please Run the installer program Setup.exe in the
LAN\Realtek\RTL8111B_8111C\Vista_Vista64 folder to install the Vista
drivers automatically. Or please browse to this location when Windows
ask you to specify the driver location. Then follow the on-screen
instructions of the Windows will complete the installation.
4. Windows Vista Installation
Dual Channel Gigabit Ethernet PCIe Card
4
The Windows 98SE, ME, 2000, XP and XP-64bit drivers are in the
following folder of the driver CD.
Please run (double click) the setup program Setup.exe in the
LAN\Realtek\RTL8111B_8111C\98SE_ME_2K_XP_XP64 folder to install
the drivers automatically. Or browse to this location when Windows
installation Wizard asks you to specify the driver location. Just follow
the instructions of the Windows to complete the installation.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

ANTAIRA Dual Channel Gigabit Ethernet PCIe Card Installation guide

Brand
ANTAIRA
Model
Dual Channel Gigabit Ethernet PCIe Card
Category
Interface cards/adapters
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents