Samsung PS43E400U1M User manual

Samsung
Brand
Samsung
Model
PS43E400U1M
Category
Plasma TVs
Type
User manual
Plasma TV
user manual
Thank you for purchasing this Samsung product.
To receive more complete service, please register
your product at
www.samsung.com/register
Model _____________ Serial No. _____________
© 2012 Samsung Electronics Co., Ltd. All rights reserved.
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
Country Customer Care Centre Web Site
AUSTRALIA 1300 362 603 www.samsung.com
NEW ZEALAND 0800 SAMSUNG (0800 726 786) www.samsung.com
CHINA 400-810-5858 www.samsung.com
HONG KONG (852) 3698-4698
www.samsung.com/hk
www.samsung.com/hk_en/
INDIA
1800 1100 11
3030 8282
1800 3000 8282
1800 266 8282
www.samsung.com
INDONESIA
0800-112-8888
021-5699-7777
www.samsung.com
JAPAN 0120-327-527 www.samsung.com
MALAYSIA 1800-88-9999 www.samsung.com
PHILIPPINES
1-800-10-SAMSUNG(726-7864) for PLDT
1-800-3-SAMSUNG(726-7864) for Digitel
1-800-8-SAMSUNG(726-7864) for Globe
02-5805777
www.samsung.com
SINGAPORE 1800-SAMSUNG(726-7864) www.samsung.com
THAILAND
1800-29-3232
02-689-3232
www.samsung.com
TAIWAN
0800-329-999
0266-026-066
www.samsung.com
VIETNAM 1 800 588 889 www.samsung.com
BN68-04343B
BN68-04343B-02
[PE400-ASIA]BN68-04343B-ENG.indb 1 2012-03-28 �� 9:20:39
2
English
Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.
Product design and specifications may be changed without notice.
User Instructions
• Screen Image retention
Do not display a still image (such as on a video game) on the plasma display panel for more than several minutes as it can cause screen image
retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the
screen when displaying a still image.
• Heat on the top of the Plasma TV
The top side of the product may be hot after long periods of use as heat dissipates from the panel through the vent hole in the upper part of the
product.
This is normal and does not indicate any defect or operation failure of the product.
However, children should be prevented from touching the upper part of the product.
• The product is making a “cracking” noise.
A “cracking” noise may occur when the product contracts or expands due to a change in the surrounding environment such as temperature or
humidity. This is normal and not a defect of the unit.
• Cell Defects
The PDP uses a panel consisting of 1,226,880(SD-level) to 6,221,000(FHD-level) pixels which require sophisticated technology to produce.
However, there may be a few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.
• Avoid operating the TV at temperatures below 41°F (5°C)
• A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the Plasma TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and centre
of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause similar effects
to the screen.
Damages caused by the above effect are not covered by the Warranty.
• After-images on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images.
To prevent this effect, reduce the “brightness” and “contrast” when displaying still images for a long time.
• Warranty
Warranty does not cover any damage caused by image retention.
Burn-in is not covered by the warranty.
[PE400-ASIA]BN68-04343B-ENG.indb 2 2012-03-28 �� 9:20:39
3
English
Contents
Check the Symbol!
t
O
This function can be used by pressing the
TOOLS button on the remote control.
NOTE One-Touch Button
Getting Started
4
4 Accessories
5 Using the TV’s Controller (Panel Key)
6 Viewing the Remote Control
7 Setup (Initial Setup)
8 Connections
9 Changing the Input Source
Basic Features
10
10 Using the INFO button (Now & Next guide)
10 Using Channel menu
12 Retuning Channels
13 Changing the Preset Picture Mode
14 Changing the Picture Options
15 Changing the Preset Sound Mode
15 Adjusting Sound Settings
Preference Features
17
17 Executing initial setup
17 Setting the Time
17 Using the Sleep Timer
17 Setting the On / Off Timer
18 Other Features
18 Economical Solutions
18 Locking Programme
20 Support Menu
Advanced Features
21
21 Using the Media Contents
21 Connecting a USB Device
22 Screen Display
25 Media Contents - Additional Functions
Other Information
27
27 Teletext Feature
28 Installing the Wall Mount
29 Securing the TV to the Wall
29 To avoid the TV from falling
29 Anti-theft Kensington Lock
30 Troubleshooting
33 Licence
33 Storage and Maintenance
34 Specifications
35 Index
[PE400-ASIA]BN68-04343B-ENG.indb 3 2012-03-28 �� 9:20:40
Getting Started
4
English
Accessories
✎
Please make sure the following items are included with your TV. If any items are missing, contact your dealer.
✎
The items’ colours and shapes may vary depending on the models.
✎
Cables not included in the package contents can be purchased separately.
• Remote Control & Batteries (AAA x 2) • Power Cord
• Owner’s Instructions • Cleaning Cloth
• Warranty Card / Safety Guide (Not available in some locations)
Securing the Installation Space
Keep the required distances between the product and other objects (e.g. walls) to ensure proper ventilation.
Failing to do so may result in fire or a problem with the product due to an increase in the internal temperature of the product.
✎
When using a stand or wall-mount, use parts provided by Samsung Electronics only.
• If you use parts provided by another manufacturer, it may result in a problem with the product or an injury due to the
product falling.
✎
The appearance may differ depending on the product.
✎
Be careful when you contact the TV because some parts can be somewhat hot.
Installation with a stand. Installation with a wall-mount.
10 cm10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
Getting Started
[PE400-ASIA]BN68-04343B-ENG.indb 4 2012-03-28 �� 9:20:40
01 Getting Started
5
English
Using the TV’s Controller (Panel Key)
TV Controller is a multi directional button that helps navigate without remote control.
✎
Some functions which require a PIN code may not be available.
✎
The product colour and shape may vary depending on the model.
✎
Exits the menu when pressing the controller more than 1 second.
✎
When selecting the function by moving the controller to the up/down/left/right directions, be sure not to press the
controller. If you press it first, you cannot operate it to move the up/down/left/right directions.
Function menu
Return
Remote control sensor
TV Controller
Down (Front)
Up (Rear)
Right
Left
Power on Turns the TV on by pressing the controller in standby mode.
Adjusting the volume Adjusts the volume by moving the controller from side to side when the
power is on.
Selecting a channel Selects a channel by moving the controller up and down when the power is
on.
Using the function menu Press the controller when the power is on, then the function menu screen
appears. If you press it again, the function menu screen disappears.
Using the Menu
Selects the MENU(
m
) by moving the controller in the function menu screen.
The OSD(On Screen Display) of your TV’s feature appears.
Selecting the Source Selects the Source( ) by moving the controller in the function menu
screen. The Source list screen appears.
Selecting the Contents Home Selects the Contents Home( ) by moving the controller in the function
menu screen. The Contents Home main screen appears.
Power Off
Selects the Power Off(
P
) to turn the TV off by moving the controller in the
function menu screen.
Standby mode
Do not leave your TV in standby mode for long periods of time (when you are away on a holiday, for example). A small amount
of electric power is still consumed even when the power button is turned off. It is best to unplug the power cord.
[PE400-ASIA]BN68-04343B-ENG.indb 5 2012-03-28 �� 9:20:41
Getting Started
6
English
Viewing the Remote Control
✎
This is a special remote control for the visually impaired persons and has Braille points on the Power, Channel, and
Volume buttons.
A B C D
DUAL I-II
P.SIZE
AD/SUBT.
CONTENT
Installing batteries (Battery size: AAA)
Turns the TV on and off.
Displays and selects the available video sources.
Returns to the previous channel.
Cuts off the sound temporarily.
Changes channels.
Displays channel lists on the screen.
Displays the EPG (Electronic Programme Guide).
Displays information on the TV screen.
Exits the menu.
Press to directly access to channels.
Adjusts the volume.
Alternately select Teletext ON, Double, Mix or
OFF.
Displays the main on-screen menu.
Quickly select frequently used functions.
Views the Contents Home.
Returns to the previous menu.
Selects the on-screen menu items and changes
the values seen on the menu.
Use these buttons according to the direction on
screen.
Use these buttons in a specific feature.
For details, refer to the e-Manual.
DUAL I-II: Select Dual sound mode.
P.SIZE: Selects the picture size.
AD/SUBT.: Audio Description selection. (Not
available in some locations) / Displays digital
subtitles.
[PE400-ASIA]BN68-04343B-ENG.indb 6 2012-03-28 �� 9:20:42
01 Getting Started
7
English
Setup (Initial Setup)
When the TV is initially powered on, a sequence of on-screen
prompts will assist in configuring basic settings. Press the
POWER
P
button. Setup is available only when the source
is set to TV.
1. Menu Language (depending on the country):
Selecting a menu language
Press the ▲ or ▼ button, then press the ENTER
E
button.
Select the desired OSD (On Screen Display) language.
2. Use Mode: Selecting Store Demo or Home Use
Press the ▲ or ▼ button, then press the ENTER
E
button.
Select the Home Use mode. Store Demo mode is for
retail environments.
✎
When pressing TV controller, the function menu
screen appears. Select the MENU(
m
) and press it
more than 5 seconds using the controller. The Store
Demo mode is set.
✎
Cancel the Store Demo by selecting Source( ) and
pressing it more than 5 seconds.
✎
Store Demo is only for shop display. If you select it,
several functions are not able to use. Please select
Home Use when you watch at home.
3. Area: Selecting an Area
Press the ▲ or ▼ button, then press the ENTER
E
button.
Select the appropriate area.
4. Auto Tuning (Step 1): Selecting how you watch your
TV
Let’s find and store channels on your TV. Do you need
to search for channels?
• Yes, I need to.: Memorises all of the available channels
using RF cable.
• No, I don’t need to.: You don’t need to use Auto
Tuning to find channels.
5. Auto Tuning (Step 2): Selecting a search options
Select the desired broadcasting signal. Press the
▲/▼/◄/► button, then press the ENTER
E
button.
When selecting Digital & Analogue, Digital and
Analogue. For more information, refer to Channel → Auto
Tuning.
✎
Press the ENTER
E
button at any time to interrupt
the memorisation process.
6. Clock: Setting the Clock Mode
• Auto: Set the current time automatically.
• Manual: Allows you to manually set the current date
and time.
7. Setup Complete
Press the ENTER
E
button.
✎
The completed settings are displayed.
If You Want to Reset This Feature...
Select System - Setup (Initial Setup). Enter your 4 digit PIN
number. The default PIN number is “0-0-0-0”. If you want to
change the PIN number, use the Change PIN function.
You should do Setup (MENU → System) again at home
although you did in shop.
✎
If you forget the PIN code, press the remote control
buttons in the following sequence in Standby mode,
which resets the PIN to “0-0-0-0”: MUTE → 8 → 2 → 4
→ POWER (on)
[PE400-ASIA]BN68-04343B-ENG.indb 7 2012-03-28 �� 9:20:43
Getting Started
8
English
Connections
HDMI IN 2
HDMI IN 1
COMPONENT / AV IN
AUDIO
VIDEO
SERVICE
ANT IN
(5V 0.5A)
AUDIO OUT
R-AUDIO-L
P
R
P
B
Y
COMPONENT OUT
AUDIO OUT
R-AUDIO-L
VIDEO OUT
R B
R B RG
WR
R
Y
Y
W
W
R
W
R
G
HDMI OUT
R
VHF/UHF Antenna
Cable
USB
or
TV Rear Panel
TV Side Panel
BD Player
HDMI connection
BD Player
Component connection
BD Player
AV connection
✎
The position of port
may differ depending
on the model.
✎
The PDP device may interfere with an amateur
radio or AM radio.
✎
When using two-way radio mobile and portable
units or amateur radio or AM radio near by your TV,
this may cause the TV to malfunction.
[PE400-ASIA]BN68-04343B-ENG.indb 8 2012-03-28 �� 9:20:44
01 Getting Started
9
English
SERVICE
SERVICE
Connector for service only.
✎✎
NOTE
• The interlace mode is not supported.
• The set might operate abnormally if a non-standard video format is selected.
• Separate and Composite modes are supported. SOG(Sync On Green) is not supported.
• PC(D-Sub) and PC/DVI AUDIO IN input are not supported.
• DIGITAL AUDIO OUT(OPTICAL) is not supported.
Changing the Input Source
Source
TV / HDMI1 / HDMI2 / AV / Component
Use to select TV or other external input sources such as DVD / Blu-ray players / cable box / STB satellite receiver connected to
the TV.
✎
In the source list, connected inputs will be highlighted.
✎
Press the TOOLS button.
• Edit Name
You can set an external input sources name you want.
• Information
You can see detailed information about the connected external device.
[PE400-ASIA]BN68-04343B-ENG.indb 9 2012-03-28 �� 9:20:45
Basic Features
10
English
Channel Menu
¦ Using the INFO button (Now & Next guide)
The display identifies the current channel and the status of
certain audio-video settings.
The Now & Next guide shows daily TV programme
information for each channel according to the broadcasting
time.
✎
When you press the
a
(Information) button, you can
see the details of the programme.
■ Scroll ◄, ► to view information for a desired programme
while watching the current channel.
■ Scroll ▲, ▼ to view information for other channels. If you
want to move to the currently selected channel, press
the ENTER
E
button.
¦ Using Channel menu
O
MENU
m
→ Support → Contents Home → ENTER
E
Press the CONTENT button to select the desired menu.
Each screen will be displayed.
Channel List Guide Media Play Schedule Manager Source
Contents Home
R
Return
Channel List
You can view channel information, All, TV, Radio, Data/
Other, Analogue or Favourites 1-5.
✎
When you press the CH LIST button on the remote
control, Channel List screen will be displayed at once.
■ All: Shows all currently available channels.
■ TV: Shows all currently available TV channels.
■ Radio: Shows all currently available radio channels.
■ Data/Other: Shows all currently available MHP or other
channels.
■ Analogue: Shows all currently available analogue
channels.
■ Favourites 1-5: Shows all favourite channels.
✎
If you want to view favourite channels you added,
press the CH LIST button and use
L
(Ch. Mode)
button to move Favourites 1-5.
✎
Using the control buttons with the Channel List.
■
T
(Tools): Displays the option menu.
■
L
(Ch. Mode / Channel): Move to the All, TV, Radio,
Data/Other, Analogue or Favourites 1-5.
✎
When you select the Programme View in
T
(Tools) menu, you can move to other channels
using
L
(Channel) button.
■
E
(Watch / Information): Watches the channel you
selected. / Displays details of the selected programme.
■
k
(Page): Move to next or previous page.
How to use Schedule Viewing in Channel List
(digital channels only)
When you set the Schedule Viewing in Channel List, you
can only set the programme in Programme View.
1. Press the CH LIST button, then select a desired digital
channel.
2. Press TOOLS button, and then select the Programme
View. The programme list for that channel appears.
3. Press the ▲ / ▼ buttons to select the desired
programme, then press the ENTER
E
(Information) or
INFO button.
4. Select Schedule Viewing, then press the ENTER
E
button when done.
✎
If you want to cancel Schedule Viewing, follow steps 1
through 3. Select Cancel schedule.
Using Option Menu
t
Set each channel using the Channel List menu options
(Programme View, Edit Favourites, Lock/Unlock,
Edit Channel Name, Edit Channel Number, Delete,
Information, Edit Mode).
Option menu items may differ depending on the channel
status.
1. Select a channel and press the TOOLS button.
2. Select a function and change its settings.
■ Programme View: Displays the programme when digital
channel is selected.
■ Edit Favourites: Set channels you watch frequently
as favourites. Add or delete the selected channel in
Favourites 1-5.
1. Select the Edit Favourites, then press the
ENTER
E
button.
2. Press the ENTER
E
button to select Favourites
1-5, then press the OK button.
✎
One favourite channel can be added in several
of favourites among Favourites 1-5.
• Lock/Unlock: Lock a channel so that the channel cannot
be selected and viewed.
✎
This function is available only when the Channel
Lock is set to On.
✎
The PIN input screen appears. Enter your 4-digit
PIN. Change the PIN using the Change PIN option.
Basic Features
[PE400-ASIA]BN68-04343B-ENG.indb 10 2012-03-28 �� 9:20:46
02 Basic Features
11
English
■ Edit Channel Name (analogue channels only): Assign
your own channel name.
■ Edit Channel Number: Edit the number by pressing the
number buttons desired.
✎
Some area may not be able to support Edit
Channel Name and Edit Channel Number
function.
■ Delete: You can delete a channel to display the channels
you want.
■ Information: Displays details of the selected
programme.
■ Edit Mode: You can select desired channels and edit it.
Using Option Menu
t
Set each channel using the menu options (Edit
Favourites, Lock/Unlock, Delete, Deselect, Select
All).
1. Press the TOOLS button in Channel List screen,
then select the Edit Mode. A check box appears to
the left of the channel.
2. Press the ▲/▼ buttons to select the desired
channel, then press the ENTER
E
button. The (
c
)
mark indicates the channel you’ve selected.
✎
You can select more than one channel.
✎
Press the ENTER
E
again to deselect the
channel.
3. Press the TOOLS button, then select a function and
change its settings.
• Edit Favourites: Set the selected channels you
watch frequently as favourites.
✎
The Edit Favourites screen has five groups
(Favourites 1, Favourites 2, etc.). You can add
a favourite channel to any one of the groups.
Press the ▲/▼ buttons to select a group.
• Lock/Unlock: Lock a channel so that the channel
cannot be selected and viewed.
✎
This function is available only when the
Channel Lock is set to On.
✎
The PIN input screen appears. Enter your
4-digit PIN. Change the PIN using the Change
PIN option.
• Delete: You can delete a channel to display the
channels you want.
• Deselect: Deselect the selected channels.
• Select All: Select all the channels in the channel list.
Guide
The EPG (Electronic Programme Guide) information is
provided by broadcasters. Using programme schedules
provided by broadcasters, you can specify programmes you
want to watch in advance so that the channel automatically
changes to the selected programme channel at the specified
time. Programme entries may appear blank or out of date
depending on a channel status.
Die Musik-Show
DTV Air 825 NDR FERNSEHEN
19:15 - 20:40
Dani is devastated when scot makes clear his views ...
825 NDR FERNSEHEN
18:15 Sat 1 May
Channel View - All
Today
▲
821 Kanal 5
822 M6
823 MDR FERNSEHEN
824 Mediashopping
825 NDR FERNSEHEN
▼
826
NT1
20:00 21:0020:30 21:30
No Information
No Information
No Information
Musik fur Sie MD... Ein Schloss am ...
No Information
a
Sche. Mgr
b
-24 Hours
{
+24 Hours
}
Ch. Mode
`
Information
k
Page
E
Schedule
1 2 3 4
5
6 7
Guide
Die Musik-Show Die NDR Quizshow Sportclub live
1
a
Red (Sche. Mgr): Moves to the reserved programmes
in Sche. Mgr.
2
b
Green (-24 Hours): Viewing the list of programmes to
be broadcasted before 24 hours.
3
{
Yellow (+24 Hours): Viewing the list of programmes to
be broadcasted after 24 hours.
4
}
Blue (Ch. Mode): Select the type of channels you
want to display on the Channel List window. (All, TV,
Radio, Data/Other, Favourites 1-5)
5
`
(Information): Displays details of the selected
programme.
6
k
(Page): Move to previous or next page.
7
E
(Watch / Schedule)
• When selecting the current programme, you can
watch the selected programme.
• When selecting the future programme, you can
reserve to watch the selected programme. To cancel
the schedule, press the ENTER
E
button again
and select Cancel schedule.
[PE400-ASIA]BN68-04343B-ENG.indb 11 2012-03-28 �� 9:20:48
Basic Features
12
English
Schedule Manager
You can set a desired channel to be displayed automatically
at the intended time. In addition, you can view, modify or
delete a channel you have reserved to watch. Set the current
time first to use this function.
Using Option Menu
t
Set each channel using the menu options (Cancel schedule,
Edit Schedule, Schedule manually, View Guide).
1. Press the TOOLS button to select the Schedule
manually.
✎
You can press the
a
(Schedule manually) directly
on the Schedule Manager screen.
2. Press the ◄/►/▲/▼ or number buttons to set the
Aerial, Channel, Repeat, Date, Start Time.
• Aerial: Select the desired broadcasting signal.
• Channel: Select the desired channel.
• Repeat: Select Once, Manual, Sat~Sun, Mon~Fri
or Everyday to set at your convenience. If you
select Manual, you can set the day you want.
✎
The (
c
) mark indicates the day you’ve
selected.
• Date: You can set the desired date.
✎
It is available when you select Once in Repeat.
• Start Time: You can set the start time you want.
✎
If you want to edit or cancel the schedule, select the
reserved schedule on the Reserved Programmes.
Press the TOOLS button, then select the Edit
Schedule or Cancel schedule.
✎
If you select the View Guide, you can see the Guide
screen.
¦ Retuning Channels
Area
O
MENU
m
→ Channel → Area → ENTER
E
You can change the desired area.
Auto Tuning
(depending on the country)
O
MENU
m
→ Channel → Auto Tuning → ENTER
E
Scans for a channel automatically and stores in the TV.
✎
Automatically allocated programme numbers may not
correspond to actual or desired programme numbers. If
a channel is locked, the PIN input window appears.
• Digital & Analogue / Digital / Analogue: Select the
channel source to memorise.
Manual Tuning
O
MENU
m
→ Channel → Manual Tuning → ENTER
E
Scans for a channel manually and stores in the TV.
✎
If a channel is locked, the PIN input window appears.
✎
According to the channel source, Manual Tuning may
be supported.
When Aerial Source is set to Air or Cable:
■ Digital Channel Tuning: Scans for a digital channel
manually and stores in the TV. Press the New button to
search the digital channels. When scanning has finished,
a channel is updated in the channel list.
■ Analogue Channel Tuning: Scans for an analogue
channel. Press the New button to search the channels
by adjusting the Programme, Colour System, Sound
System, Channel, Search.
Channel mode
–
P (programme mode): When tuning is complete,
the broadcasting stations in your area have been
assigned to the position numbers from P0 to P99.
You can select a channel by entering the position
number in this mode.
–
C (aerial channel mode) / S (cable channel mode):
These two modes allow you to select a channel
by entering the assigned number for each aerial
broadcasting station or cable channel.
Fine Tune
(analogue channels only)
O
MENU
m
→ Channel → Fine Tune → ENTER
E
If the signal is weak or distorted, fine tune the channel
manually.
✎
Fine tuned channels are marked with an asterisk “*”.
✎
To reset the fine-tuning, select Reset.
[PE400-ASIA]BN68-04343B-ENG.indb 12 2012-03-28 �� 9:20:49
02 Basic Features
13
English
Picture Menu
¦ Changing the Preset Picture Mode
O
MENU
m
→ Picture → Picture Mode → ENTER
E
Picture Mode
t
Select your preferred picture type.
• Dynamic: Suitable for a bright room.
• Standard: Suitable for a normal environment.
• Movie: Suitable for watching movies in a dark room.
Cell Light / Contrast / Brightness / Sharpness
/ Colour / Tint (G/R)
Your television has several setting options for picture quality
control.
✎
NOTE
• In analogue TV, AV modes of the PAL system, the
Tint (G/R) function is not available.
• Settings can be adjusted and stored for each
external device connected to the TV.
• Lowering picture brightness reduces power
consumption.
Screen Adjustment
O
MENU
m
→ Picture → Screen Adjustment →
ENTER
E
Set the various picture options such as picture size and
aspect ratio.
■ Picture Size: Your cable box/satellite receiver may have
its own set of screen sizes as well. However, we highly
recommend you use 16:9 mode most of the time.
Auto Wide: Automatically adjusts the picture size to the
16:9 aspect ratio.
16:9: Sets the picture to 16:9 wide mode.
Wide Zoom: Magnifies the picture size more than 4:3.
✎
Adjusts the Position by using ▲, ▼ buttons.
Zoom: Magnifies the 16:9 wide pictures vertically to fit
the screen size.
✎
Adjusts the Zoom or Position by using ▲, ▼
button.
4:3: Sets the picture to basic (4:3) mode.
✎
Do not watch in 4:3 format for a long time. Traces
of borders displayed on the left, right and centre
of the screen may cause image retention (screen
burn) which are not covered by the warranty.
Screen Fit: Displays the full image without any cut-off
when HDMI (720p / 1080i / 1080p) or Component
(1080i / 1080p) signals are inputted.
■ Position: Adjust the picture position. It is only available
in Screen Fit or Wide Zoom.
■ Zoom/Position: Adjust the picture size and position. It is
only available in Zoom.
✎
NOTE
• After selecting Screen Fit in HDMI (1080i / 1080p)
or Component (1080i / 1080p) mode, you may need
to centre the picture:
1. Press the ▲ or ▼ button to select Position.
2. Press the ENTER
E
button.
3. Press the ▲, ▼, ◄ or ► button to move the
picture.
• Depending on the input source, the picture size
options may vary.
• If you want to reset the position you adjusted, select
Reset in the Position screen. The picture will be set
to its default position.
• The available items may differ depending on the
selected mode.
• Settings can be adjusted and stored for each
external device connected to an input on the TV.
• If you use the Screen Fit function with HDMI 720p
input, 1 line will be cut at the top, bottom, left and
right as in the overscan function.
■ 4:3 Screen Size (16:9 / Wide Zoom / Zoom / 4:3):
Available only when picture size is set to Auto Wide. You
can determine the desired picture size at the 4:3 WSS
(Wide Screen Service) size or the original size. Each
country requires different picture size.
✎
It is only available in Auto Wide.
[PE400-ASIA]BN68-04343B-ENG.indb 13 2012-03-28 �� 9:20:50
Basic Features
14
English
¦ Changing the Picture Options
Advanced Settings
O
MENU
m
→ Picture → Advanced Settings →
ENTER
E
(available in Standard / Movie mode)
You can adjust the detailed setting for the screen including
colour and contrast.
Advanced Settings
Dynamic Contrast Medium
Black Tone Off
Flesh Tone 0
RGB Only Mode Off
Colour Space Native
White Balance
Gamma 0
■ Dynamic Contrast (Off / Low / Medium / High): Adjust
the screen contrast.
■ Black Tone (Off / Dark / Darker / Darkest): Select the
black level to adjust the screen depth.
■ Flesh Tone: Adjust the flesh tone colour.
■ RGB Only Mode (Off / Red / Green / Blue): Displays
the Red, Green and Blue colour for making fine
adjustments to the hue and saturation.
■ Colour Space (Auto / Native): Adjust the range of
colours available to create the image.
■ White Balance: Adjust the colour temperature for a
more natural picture.
R-Offset / G-Offset / B-Offset: Adjust each colour’s
(red, green, blue) darkness.
R-Gain / G-Gain / B-Gain: Adjust each colour’s (red,
green, blue) brightness.
Reset: Resets the White Balance to its default settings.
■ Gamma: Adjust the primary colour intensity.
Picture Options
O
MENU
m
→ Picture → Picture Options → ENTER
E
■ Colour Tone (Cool / Standard / Warm1 / Warm2)
✎
Warm1 or Warm2 will be deactivated when the
picture mode is Dynamic.
✎
Settings can be adjusted and stored for each
external device connected to an input on the TV.
■ Digital Noise Filter (Off / Low / Medium / High / Auto
/ Auto Visualisation): If the broadcast signal received
by your TV is weak, you can activate the Digital Noise
Filter feature to reduce any static and ghosting that may
appear on the screen.
✎
When the signal is weak, try other options until the
best picture is displayed.
Auto Visualisation: When changing analogue channels,
displays signal strength.
✎
Only available for analogue channels.
✎
When the INFO button is pressed, the signal
strength bar is displayed.
✎
When bar is green, you are receiving the best
possible signal.
■ MPEG Noise Filter (Off / Low / Medium / High /
Auto): Reduces MPEG noise to provide improved
picture quality.
■ HDMI Black Level (Low / Normal): Selects the black
level on the screen to adjust the screen depth.
✎
Available only in HDMI mode (RGB signals).
■ Film Mode (Off / Auto1 / Auto2): Sets the TV to
automatically sense and process film signals from all
sources and adjust the picture for optimum quality.
✎
Available in TV mode, AV, Component (480i / 1080i)
and HDMI (1080i).
✎
If the screen does not seem natural, change its
option to Off / Auto1 / Auto2 in Film Mode.
Reset Picture (Yes / No)
O
MENU
m
→ Picture → Reset Picture → ENTER
E
Resets your current picture mode to its default settings.
[PE400-ASIA]BN68-04343B-ENG.indb 14 2012-03-28 �� 9:20:51
02 Basic Features
15
English
Sound Menu
¦ Changing the Preset Sound Mode
Sound Mode
t
O
MENU
m
→ Sound → Sound Mode → ENTER
E
■ Standard: Selects the normal sound mode.
■ Music: Emphasizes music over voices.
■ Movie: Provides the best sound for movies.
■ Clear Voice: Emphasizes voices over other sounds.
■ Amplify: Increase the intensity of high-frequency sound
to allow a better listening experience for the hearing
impaired.
¦ Adjusting Sound Settings
Sound Effect
(standard sound mode only)
O
MENU
m
→ Sound → Sound Effect → ENTER
E
Use the up and down arrow keys to select an option, and
then press ENTER
E
.
■ SRS TruSurround HD (Off / On)
(standard sound mode only)
This function provides a virtual 5.1 channel surround
sound experience through a pair of speakers using
HRTF (Head Related Transfer Function) technology.
■ SRS TruDialog (Off / On)
(standard sound mode only)
This function allows you to increase the intensity of a
voice over background music or sound effects so that
dialogue can be heard more clearly.
■ Equaliser
(standard sound mode only)
Use Equaliser to customize sound setting for each
speaker.
Balance: Adjusts the balance between the right and left
speaker.
100Hz / 300Hz / 1kHz / 3kHz / 10kHz (Bandwidth
Adjustment): Adjusts the level of specific bandwidth
frequencies.
Reset: Resets the equaliser to its default settings.
Broadcast Audio Options
O
MENU
m
→ Sound → Broadcast Audio Options →
ENTER
E
■ Audio Language
t
(digital channels only)
Change the default value for audio languages.
✎
The available language may differ depending on
the broadcast.
■ Audio Format
(digital channels only)
When sound is emitted from both the main speaker and
the audio receiver, a sound echo may occur due to the
decoding speed difference between the main speaker
and the audio receiver. In this case, use the TV Speaker
function.
■ Audio Description
(not available in all locations) (digital channels only)
This function handles the Audio Stream for the AD
(Audio Description) which is sent along with the Main
audio from the broadcaster.
Audio Description (Off / On): Turn the audio description
function on or off.
Volume: Adjust the audio description volume.
[PE400-ASIA]BN68-04343B-ENG.indb 15 2012-03-28 �� 9:20:52
Basic Features
16
English
Additional Settings
O
MENU
m
→ Sound → Additional Settings → ENTER
E
■ DTV Audio Level (MPEG / HE-AAC) (digital channels
only): This function allows you to reduce the disparity of
a voice signal (which is one of the signals received during
a digital TV broadcast) to a desired level.
✎
According to the type of broadcast signal, MPEG /
HE-AAC can be adjusted between -10dB and 0dB.
✎
To increase or decrease the volume, adjust
between the range 0 and -10 respectively.
■ Dolby Digital Comp (Line / RF): This function minimizes
signal disparity between a dolby digital signal and a
voice signal (i.e. MPEG Audio, HE-AAC, ATV Sound).
✎
Select Line to obtain dynamic sound, and RF
to reduce the difference between loud and soft
sounds at night time.
Line: Set the output level for signals greater or less than
-31dB (reference) to either -20dB or -31dB.
RF: Set the output level for signals greater or less than
-20dB (reference) to either -10dB or -20dB.
Speaker Settings
O
MENU
m
→ Sound → Speaker Settings → ENTER
E
■ Auto Volume (Off / Normal / Night)
To equalize the volume level on each channel, set to
Normal.
Night: This mode provides an improved sound
experience compared to Normal mode, making almost
no noise. It is useful at night.
✎
To use the volume control on the source device
connected to the TV, set Auto Volume to Off on
the TV. Otherwise, a change to the volume control
of the source device may not be applied.
Reset Sound (Yes / No)
O
MENU
m
→ Sound → Reset Sound → ENTER
E
Reset all sound settings to the factory defaults.
Selecting the Sound Mode t
When you set to Dual I-II, the current sound mode is
displayed on the screen.
Audio Type Dual I-II Default
A2 Stereo
Mono
Mono
Automatic
change
Stereo
Stereo
↔
Mono
Dual
Dual I
↔
Dual II
Dual I
NICAM
Stereo
Mono Mono
Automatic
change
Stereo
Mono
↔
Stereo
Dual
Mono
→
Dual I
Dual II
Dual I
✎
If the stereo signal is weak and an automatic switching,
occurs, then switch to the mono.
✎
Only activated in stereo sound signal.
✎
Only available when the Source is set to TV.
[PE400-ASIA]BN68-04343B-ENG.indb 16 2012-03-28 �� 9:20:52
03 Preference Features
17
English
System Menu
¦ Executing initial setup
Setup
O
MENU
m
→ System → Setup → ENTER
E
Configure the channels and the time when setting up the TV
for the first time or when resetting the unit.
¦ Setting the Time
Time
O
MENU
m
→ System → Time → ENTER
E
The current time will appear every time you press the INFO
button.
■ Clock: Setting the clock is for using various timer
features of the TV.
✎
If you disconnect the power cord, you have to set
the clock again.
Clock Mode: Set up the current time manually or
automatically.
–
Auto: Set the current time automatically using the
time from a digital channel.
✎
The aerial must be connected in order to set the
time automatically.
–
Manual: Set the current time manually.
✎
Depending on the broadcast station and signal, the
auto time set up may not be correct. In this case,
set the time manually.
Clock Set: Set the Date and Time.
✎
Available only when Clock Mode is set to Manual.
✎
You can set the Date and Time directly by pressing
the number buttons on the remote control.
Time Zone (depending on the country): Select your time
zone.
✎
This function is only available when the Clock
Mode is set to Auto.
¦ Using the Sleep Timer
O
MENU
m
→ System → Time → Sleep Timer →
ENTER
E
■ Sleep Timer
t
: Automatically shuts off the TV
after a preset period of time. (30, 60, 90, 120, 150 and
180 minutes).
✎
To cancel Sleep Timer, select Off.
¦ Setting the On / Off Timer
O
MENU
m
→ System → Time → On Timer <or> Off
Timer → ENTER
E
■ On Timer 1 / On Timer 2 / On Timer 3: Three different
on timer settings can be made. You must set the clock
first.
–
Setup: Select Off, Once, Everyday, Mon~Fri,
Mon~Sat, Sat~Sun or Manual to set at your
convenience. If you select Manual, you can set up
the day you want to activate the timer.
✎
The
c
mark indicates the day you’ve
selected.
–
Time: Set the hour and minute.
–
Volume: Set the desired volume level.
–
Source: Select TV or USB content to be played
when the TV is turned on automatically. (USB can be
selected only when a USB device is connected to the
TV)
–
Aerial (when the Source is set to TV): Select ATV or
DTV.
–
Channel (when the Source is set to TV): Select the
desired channel.
–
Music / Photo (when the Source is set to USB):
Select a folder in the USB device containing music
or photo files to be played when the TV is turned on
automatically.
✎
NOTE
• If there is no music file on the USB device
or the folder containing a music file is
not selected, the timer function does not
operate correctly.
• When there is only one photo file in the
USB device, the slide show will not play.
• If a folder name is too long, the folder
cannot be selected.
• Each USB you use is assigned its own
folder. When using more than one of the
same type of USB, make sure the folders
assigned to each USB have different
names.
• It is recommended that you use a USB
memory stick and a multi card reader when
using On Timer.
• The On Timer function may not work
with USB devices with a built-in battery,
MP3 players, or PMPs made by some
manufacturers because these devices take
a long time to be recognized.
Preference Features
[PE400-ASIA]BN68-04343B-ENG.indb 17 2012-03-28 �� 9:20:53
Preference Features
18
English
■ Off Timer 1 / Off Timer 2 / Off Timer 3: Three different
off timer settings can be made. You must set the clock
first.
Setup: Select Off, Once, Everyday, Mon~Fri,
Mon~Sat, Sat~Sun or Manual to set at your
convenience. If you select Manual, you can set up the
day you want to activate the timer.
✎
The
c
mark indicates the day you’ve selected.
Time: Set the hour and minute.
¦ Other Features
Language
O
MENU
m
→ System → Language → ENTER
E
■ Menu Language: Set the menu language.
■ Teletext Language (depending on the country): Set a
desired language for teletext.
✎
English is the default in cases where the selected
language is unavailable in the broadcast.
■ Preferred Language (Primary Audio / Secondary
Audio / Primary Subtitle / Secondary Subtitle /
Primary Teletext / Secondary Teletext): Select a
language, which will be the default language when a
channel is selected.
✎
Primary Teletext and Secondary Teletext may
not be supported in some locations.
¦ Economical Solutions
Eco Solution
O
MENU
m
→ System → Eco Solution → ENTER
E
■ Energy Saving (Off / Low / Medium / High / Picture
Off)
t
: This adjusts the brightness of the TV
in order to reduce power consumption. If you select
Picture Off, the screen is turned off, but the sound
remains on. Press any button except volume button to
turn on the screen.
■ No Signal Power Off (Off / 15 min / 30 min / 60 min):
To avoid unnecessary energy consumption, set how long
you want the TV to remain on if it’s not receiving a signal.
■ Auto Power Off (Off / On): The TV will be automatically
turned off when no user operation is received for 4
hours.
Subtitle
O
MENU
m
→ System → Subtitle → ENTER
E
Use this menu to set the Subtitle mode.
■ Subtitle (Off / On): Switches subtitles on or off.
■ Subtitle Mode (Normal / Hearing Impaired): Sets the
subtitle mode.
■ Subtitle Language: Sets the subtitle language.
✎
If the programme you are watching does not
support the Hearing Impaired function, Normal
automatically activates even if the Hearing
Impaired mode is selected.
✎
English is the default in cases where the selected
language is unavailable in the broadcast.
¦ Locking Programme
Security
O
MENU
m
→ System → Security → ENTER
E
✎
The PIN input screen appears before the setup screen.
✎
Enter your 4-digit PIN. Change the PIN using the
Change PIN option.
■ Channel Lock (Off / On): Lock channels in Channel
menu to prevent unauthorized users, such as children,
from watching unsuitable programme.
✎
Available only when the Source is set to TV.
■ Programme Rating Lock (depending on the country):
Prevent unauthorized users, such as children, from
watching unsuitable programme with a user-defined
4-digit PIN code. If the selected channel is locked, the
“
\
” symbol will be displayed.
✎
The items of Programme Rating Lock differs
depending on the country.
■ Change PIN: Change your password required to set up
the TV.
[PE400-ASIA]BN68-04343B-ENG.indb 18 2012-03-28 �� 9:20:55
03 Preference Features
19
English
Screen Burn Protection
O
MENU
m
→ System → Screen Burn Protection →
ENTER
E
To reduce the possibility of screen burn, this unit is equipped
with screen burn prevention technology. The Time setting
allows you to programme the time between movement of the
picture in minutes.
■ Pixel Shift (Off / On): Using this function, you can
minutely move pixels on the PDP in horizontal or vertical
direction to minimize after image on the screen.
✎
Optimum condition for pixel shift
Item TV / HDMI
Horizontal 0~4 3
Vertical 0~4 3
Time (minute) 1~4 min 4 min
✎
The Pixel Shift value may differ depending on the
monitor size (inches) and mode.
✎
This function is not available in the Screen Fit
mode.
■ Auto Protection Time (Off / 10 min / 20 min / 40 min
/ 1 hour): If the screen remains idle with a still image for
a certain period of time defined by the user, the screen
saver is activated to prevent the formation of ghost
images on the screen.
■ Scrolling: This function removes after-images on the
screen by moving all the pixels on the PDP according
to a pattern. Use this function when there are remaining
after images or symbols on the screen, especially when
you displayed a still image on the screen for a long time.
✎
The after-image removal function has to be
executed for a long time (approximately 1 hour) to
effectively remove after-images on the screen. If
the after-image is not removed after performing the
function, repeat the function again.
✎
Press any key on the remote control to cancel this
feature.
■ Side Grey (Light / Dark): When you watch TV with the
screen ratio set to 4:3, the screen is prevented from any
damage by adjusting the white balance on both extreme
left and right sides.
General
O
MENU
m
→ System → General → ENTER
E
■ Game Mode (Off / On): When connecting to a game
console such as PlayStation™ or Xbox™, you can enjoy
a more realistic gaming experience by selecting game
mode.
✎
NOTE
• Precautions and limitations for game mode
–
To disconnect the game console and connect
another external device, set Game Mode to
Off in the setup menu.
–
If you display the TV menu in Game Mode,
the screen shakes slightly.
• Game Mode is not available in TV mode.
• After connecting the game console, set Game
Mode to On. Unfortunately, you may notice
reduced picture quality.
• If Game Mode is On:
–
Picture Mode is set to Standard and Sound
Mode is set to Movie.
■ Panel Lock (Off / On): Lock or unlock all the keys(TV
Controller) on the panel.
■ Boot Logo (Off / On): Display Samsung logo when the
TV is turned on.
DivX® Video On Demand
O
MENU
m
→ System → DivX® Video On Demand →
ENTER
E
Shows the registration code authorized for the TV. If you
connect to the DivX web site and register with 10-digit
registration code, you can download the VOD activation file.
Once you play it using Videos, the registration is completed.
✎
For more information on DivX® VOD, visit http://vod.
divx.com.
[PE400-ASIA]BN68-04343B-ENG.indb 19 2012-03-28 �� 9:20:55
Preference Features
20
English
Support Menu
¦ Support Menu
Self Diagnosis
O
MENU
m
→ Support → Self Diagnosis → ENTER
E
✎
Self Diagnosis might take few seconds, this is part of
the normal operation of the TV.
■ Picture Test (Yes / No): Use to check for picture
problems.
■ Sound Test (Yes / No): Use the built-in melody sound to
check for sound problems.
■ Signal Information: (digital channels only) HDTV
channel’s reception quality is either perfect or the
channels are unavailable. Adjust your aerial to increase
signal strength.
■ Reset: Reset all settings to the factory defaults except
network settings.
✎
The PIN input screen appears before the setup
screen.
✎
Enter your 4-digit PIN. Change the PIN using the
Change PIN option.
Software Upgrade
O
MENU
m
→ Support → Software Upgrade →
ENTER
E
Software Upgrade can be performed by downloading the
latest firmware from “www.samsung.com” to a USB memory
device.
Current Version-the software already installed in the TV.
Installing the Latest Version
■ By USB: Insert a USB drive containing the firmware
upgrade file, downloaded from “www.samsung.com”
into the TV. Please be careful not to disconnect the
power or remove the USB drive until upgrades are
complete. The TV will be turned off and on automatically
after completing the firmware upgrade. When software
is upgraded, video and audio settings you have made
will return to their default settings. We advise you to write
down your settings so that you can easily reset them
after the upgrade.
■ Alternative Software: Replace the current software with
the alternative.
Contact Samsung
O
MENU
m
→ Support → Contact Samsung →
ENTER
E
View this information when your TV does not work properly
or when you want to upgrade the software. You can find
information regarding our call centres, and how to download
products and software.
Contents Home
O
MENU
m
→ Support → Contents Home → ENTER
E
You can enjoy useful and various contents
[PE400-ASIA]BN68-04343B-ENG.indb 20 2012-03-28 �� 9:20:56
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35

Samsung PS43E400U1M User manual

Samsung
Brand
Samsung
Model
PS43E400U1M
Category
Plasma TVs
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents