Powerplus POWX510 Owner's manual

  POWX510  EN 
Copyright © 2019 VARO  P a g e  | 1  www.varo.com 
APPLICATION .................................................................................. 3 
DESCRIPTION (FIG A) .................................................................... 3 
PACKAGE CONTENT LIST ............................................................. 3 
SYMBOLS ........................................................................................ 3 
GENERAL POWER TOOL SAFETY WARNINGS .......................... 4 
1  Working area ........................................................................................................... 4 
2  Electrical safety ....................................................................................................... 4 
3  Personal safety ....................................................................................................... 4 
4  Power tool use and care ......................................................................................... 5 
5  Service ..................................................................................................................... 5 
SAFETY INFORMATION ................................................................. 5 
1  General safety information ..................................................................................... 5 
2  Exhaust fumes are poisonous ............................................................................... 5 
3  Fuel is highly flammable and poisonous ............................................................... 5 
4  Engine and muffler can be very hot ....................................................................... 6 
5  Electric shock prevention ....................................................................................... 6 
6  Connection notes .................................................................................................... 6 
7  Personal protection ................................................................................................ 6 
ELECTRICAL SAFETY: IP23M ....................................................... 6 
ASSEMBLY ...................................................................................... 6 
1  Assembly wheel axis .............................................................................................. 6 
2  Assembly of support legs ...................................................................................... 6 
3  Assembly of handle clamp and handle .................................................................. 6 
4  Assembly wheels .................................................................................................... 7 
CONTROL FUNCTIONS .................................................................. 7 
1  Recoil starter ........................................................................................................... 7 
2  Fuel valve lever ....................................................................................................... 7 
3  Choke rod ................................................................................................................ 7 
4  Ground terminal ...................................................................................................... 7 
5  DC circuit breaker ................................................................................................... 7 
6  Oil alert system ....................................................................................................... 7 

  POWX510  EN 
Copyright © 2019 VARO  P a g e  | 2  www.varo.com 
7  AC circuit breaker ................................................................................................... 7 
PRE-OPERATION CHECK .............................................................. 7 
1  Engine oil ................................................................................................................. 7 
2  Fuel (Fig 6, 7) ........................................................................................................... 8 
3  Air filter .................................................................................................................... 8 
OPERATION ..................................................................................... 8 
1  Starting the engine .................................................................................................. 8 
2  Connecting electric tools/appliances .................................................................... 9 
3  Stopping .................................................................................................................. 9 
4  Operating time ......................................................................................................... 9 
5  Ground system ........................................................................................................ 9 
6  High altitude operation ......................................................................................... 10 
MAINTENANCE/CLEANING ......................................................... 10 
1  The importance of maintenance........................................................................... 10 
2  Maintenance chart ................................................................................................. 10 
3  Engine oil replacement ......................................................................................... 11 
4  Air filter (Fig. 10) ................................................................................................... 11 
5  Fuel sediment cup cleaning (Fig. 11) ................................................................... 11 
6  Cleaning / adjusting / replacing spark plug ......................................................... 12 
7  Muffler screen ....................................................................................................... 12 
SERVICE / REPAIRS ..................................................................... 12 
TECHNICAL DATA ........................................................................ 12 
NOISE ............................................................................................. 13 
TRANSPORT/ STORAGE .............................................................. 13 
1  Drain the fuel ......................................................................................................... 13 
TROUBLE SHOOTING .................................................................. 14 
WARRANTY ................................................................................... 14 
ENVIRONMENT ............................................................................. 15 
DECLARATION OF CONFORMITY .............................................. 15 

POWX510 EN

GENERATOR 2000W (2200W MAX)

POWX510

1 APPLICATION

This generator is intended for private use, it is not suitable for professional use.

It supplies 230 Volt, 50 Hz AC current. Technical data MAX. (cos φ = 1).

WARNING! For your own safety, read this manual and the general safety

instructions carefully before using the appliance. Your power tool should

only be given to other users together with these instructions.

2 DESCRIPTION (FIG A)

1. Fuel tank

2. Starter Handle

3. Fuel tank cap

4. Petrol level display

5. Earth Ground connection

6. AC socket(s) 230 Volt/50 Hz

7. Safety switch

8. Oil filling nozzle with dipstick

9. Oil drain bolt

10. Engine switch

11. Fuel valve

12. Volt meter

13. Spark plug

14. Choke lever

15. Muffler

16. DC circuit breaker

17. Frame

18. Oil alert lamp

19. Handle

3 PACKAGE CONTENT LIST

▪ Remove all packaging materials.

▪ Remove remaining packaging and packing inserts (if included).

▪ Check that the package contents are complete.

▪ Check the appliance, the power cord, the power plug and all accessories for transportation

damage.

▪ Keep the packaging materials as far as possible until the end of the warranty period. Then

take it to your local waste disposal system.

WARNING Packaging materials are not toys! Children must not play with

plastic bags! There is a danger of suffocation!

1pc Machine

1pc spark plug wrench

2pcs wheels (200mm) with shafts and

lock needles

1pc funnel

1 set handle with screws and nuts

2pcs support feet

1pc manual

If any parts are missing or damaged, please contact your dealer.

4 SYMBOLS

The following symbols are used in this manual and/or on the machine:

Denotes risk of personal injury

or damage to the tool.

Read manual before use.

POWX510 EN

In accordance with essential

safety standards of applicable

European directives.

Wear noise protection.

5 GENERAL POWER TOOL SAFETY WARNINGS

Read all safety warnings and instructions. Failure to heed warnings and follow instructions

may result in electric shock, fire and/or serious injury. Keep safety warnings and instructions

for future reference. The term "power tool" in the safety warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless) power tool.

5.1 Working area

▪ Keep working area clean and well lit. Untidy and dark areas can lead to accidents.

▪ Do not operate power tools in potentially explosive surroundings, for example, in the

presence of inflammable liquids, gases or dust. Power tools create sparks which may

ignite the dust or fumes.

▪ Keep children and bystanders at a distance when operating a power tool. Distractions can

cause you to lose control of it.

5.2 Electrical safety

Always check that the power supply corresponds to the voltage on the

rating plate.

▪ Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

adapter plugs with earthed power tools. Unmodified plugs and matching outlets will reduce

the risk of a lethal electric shock.

▪ Avoid body contact with earthed surfaces such as pipes, radiators, kitchen ranges and

refrigerators. There is an increased risk of a lethal electric shock if your body is earthed.

▪ Do not expose power tools to rain or wet conditions. If water gets inside a power tool, it will

increase the risk of a lethal electric shock.

▪ Do not damage the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep the cord away from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of a lethal electric shock.

▪ When operating a power tool outdoors, use an extension cable suitable for outdoor use.

Using a cord suitable for outdoor use reduces the risk of a lethal electric shock.

▪ If operating a power tool in a damp location is unavoidable, use a power supply protected

by a residual current device (RCD). Using an RCD reduces the risk of a lethal electric

shock.

5.3 Personal safety

▪ Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool when you are tired or under the influence of drugs, alcohol or

medication. A moment of inattention when operating a power tool may result in serious

personal injury.

▪ Use safety equipment. Always wear eye protection. Using safety equipment such as a

dust mask, non-skid safety shoes, a hard hat, or hearing protection whenever it is needed

will reduce the risk of personal injury.

▪ Avoid accidental starts. Ensure the switch is in the off position before inserting the plug.

Carrying power tools with your finger on the switch or plugging in power tools when the

switch is in the on position makes accidents more likely.

▪ Remove any adjusting keys or spanners before turning on the power tool. A spanner or

key left attached to a rotating part of the power tool may result in personal injury.

POWX510 EN

▪ Do not reach out too far. Keep your feet firmly on the ground at all times. This will enable

you retain control over the power tool in unexpected situations.

▪ Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

gloves away from the power tool. Loose clothes, jewellery or long hair can become

entangled in the moving parts.

▪ If there are devices for connecting dust extraction and collection facilities, please ensure

that they are attached and used correctly. Using such devices can reduce dust-related

hazards.

5.4 Power tool use and care

▪ Do not expect the power tool to do more than it can. Use the correct power tool for what

you want to do. A power tool will achieve better results and be safer if used in the context

for which it was designed.

▪ Do not use the power tool if the switch cannot turn it on and off. A power tool with a broken

switch is dangerous and must be repaired.

▪ Disconnect the plug from the power source before making adjustments, changing

accessories, or storing power tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

▪ Store power tools, when not in use, out of the reach of children and do not allow people

who are not familiar with the power tool or these instructions to operate it. Power tools are

potentially dangerous in the hands of untrained users.

▪ Maintenance. Check for misalignment or jammed moving parts, breakages or any other

feature that might affect the operation of the power tool. If it is damaged, the power tool

must be repaired. Many accidents are caused by using poorly maintained power tools.

▪ Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to jam and are easier to control.

▪ Use the power tool, accessories and cutting tools, etc., in accordance with these

instructions and in the manner intended for the particular type of power tool, taking into

account the working conditions and the work which needs to be done. Using a power tool

in ways for which it was not intended can lead to potentially hazardous situations.

5.5 Service

▪ Your power tool should be serviced by a qualified specialist using only standard spare

parts. This will ensure that it meets the required safety standards.

6 SAFETY INFORMATION

6.1 General safety information

▪ Operate the generator only on non-slip, level surfaces.

▪ Keep children and pets away from the generator.

▪ Do not operate the generator if it has visible damage.

6.2 Exhaust fumes are poisonous

Danger for asphyxiation:

▪ Never operate the engine in a closed area or it may cause unconsciousness and death

within a short time. Operate the engine in a well ventilated area.

6.3 Fuel is highly flammable and poisonous

Danger for fire /intoxication.

▪ Always turn off the engine when refueling, allow generator to cool down before refueling.

POWX510 EN

▪ Never refuel while smoking or in the vicinity of an open flame.

▪ Take care not to spill any fuel on the engine or muffler when refueling. Wipe up spilt petrol

immediately

▪ If you swallow any fuel, inhale fuel vapor, or allow any to get in your eyes, see your doctor

immediately. If any fuel spills on your skin or clothing, immediately wash with soap and

water and change your clothes.

▪ When operating or transporting the machine, be sure it is kept upright. If it tilts, fuel may

leak from the carburetor or fuel tank.

6.4 Engine and muffler can be very hot

Danger for burning

▪ Place the machine in a place where pedestrians or children are not likely to touch the

machine.

▪ Avoid placing any flammable materials near the exhaust outlet during operation.

▪ Keep the machine at least 1 m ( 3 ft ) from buildings or other equipment, or the engine

may overheat.

▪ Avoid operating the engine with a dust cover.

▪ After operation, allow to cool down before storage

6.5 Electric shock prevention

Danger of electric shock

▪ Incorrect electric installation can lead to electric shock !

▪ Never operate the engine in rain or snow.

▪ Never touch the machine with wet hands or electrical shock will occur.

▪ Be sure to ground (earth) the generator.

6.6 Connection notes

▪ Avoid connecting the generator in parallel to the commercial mains power network.

▪ Avoid connecting the generator in parallel with any other generator.

6.7 Personal protection

▪ Please wear the earplug when operate the machine.

7 ELECTRICAL SAFETY: IP23M

8 ASSEMBLY

Tilt your device so engine points upwards.

8.1 Assembly wheel axis

Mount the wheel axles on the frame in the foreseen openings with M12 nuts.

8.2 Assembly of support legs

Mount the two footrests with supplied 4 bolts M6x40 and 4 nuts M6.

8.3 Assembly of handle clamp and handle

▪ Slide the clamp over the cross bar until the holes in the handle correspond with the holes

in the cross bar. Fix the clamp with the supplied M6x60 bolt and nut. (Fig 1)

▪ Attach the holder of the handle on the top tube with two supplied bolts M8x35 and M8 nuts

in the foreseen holes. Please note that the open side of the holder should face down.

Mount the handle in the holder with the supplied spindle bolt and M6 nut. (Fig 2)

POWX510 EN

8.4 Assembly wheels

Slide every wheel over an axle. Put a cotter pin in the bore of every wheel axle and bend the

ends of the cotter pin to fix.

9 CONTROL FUNCTIONS

9.1 Recoil starter

To start the engine, pull the starter grip lightly until resistance is felt, then pull briskly.

Do not allow the starter grip to snap back against the engine. Return it

gently to prevent damage to the starter. When starting the engine by recoil

starter, set the key switch at the ON position and pull the starter handle.

9.2 Fuel valve lever

The fuel valve is located between the fuel tank and carburetor. When the valve lever is in the

ON position, fuel is allowed to flow from the fuel tank to the carburetor. Be sure to return the

fuel valve lever to the OFF position after stopping the engine.

9.3 Choke rod

The choke is used to provide an enriched fuel mixture when starting a cold engine. It can be

opened and closed by operating the choke rod manually. Pull the rod out toward CLOSED to

enrich the mixture for cold starting.

9.4 Ground terminal

The generator ground terminal is connected to the frame of the generator, the metal non-

current-carrying parts of the generator and the ground terminals of each receptacle

9.5 DC circuit breaker

The DC circuit protector automatically shuts off the DC battery charging circuit when the DC

charging circuit is overloaded, when there is a problem with the battery or when the

connections between the battery and the generator are improper.

9.6 Oil alert system

The oil alert system is designed to prevent engine damage caused by an insufficient amount

of oil in the crankcase. Before the oil level in the crankcase can fall below a safe limit, the oil

alert system will automatically stop the engine (the engine switch will remain in the ON

position). The oil alert system should not take the place of checking the oil level before each

use.

If the engine stops and will not restart, check the engine oil level before troubleshooting in

other areas.

9.7 AC circuit breaker

The AC circuit breaker will automatically switch OFF if there is a short circuit or a significant

overload of the generator at the receptacle. If the AC circuit breaker is switched OFF

automatically, check that the appliance is working properly and does not exceed the rated laod

capacity of the circuit before switching the AC circuit breaker ON again. The AC circuit breaker

may be used to switch the generator power ON or OFF.

10 PRE-OPERATION CHECK

10.1 Engine oil

Engine oil is a major factor affecting engine performance and service life.

Non-detergent and 2-stroke engine oils will damage the engine and are not

recommended.

POWX510 EN

▪ Check the oil level before each use with the generator on a level surface and the engine

stopped.

▪ Use 4-stroke motor oil.

▪ SAE 10W-30 is recommended for general, all-temperature use. Other viscosities shown in

the chart may be used when the average temperature in your area is within the indicated

range. (Fig. 3-> A: SAE Viscosity Grades, B: Ambient temperature)

1. Remove the oil filler cap and wipe the dipstick clean. (Fig. 4)

2. Check the oil level by inserting the dipstick into the filler neck without screwing it in.

3. If the level is low, fill to the top of the oil filler neck with the recommended oil. (Fig. 5)

10.2 Fuel (Fig 6, 7)

▪ Check the fuel gauge and refill the tank if the fuel is low.

▪ Refuel carefully to avoid spilling fuel. Do not fill above the shoulder of the fuel strainer.

Gasoline is highly flammable and explosive and you can be burned or

seriously injured when refueling.

▪ Stop engine and keep heat, sparks and flame away.

▪ Refuel only outdoors

▪ Wipe up spills immediately

▪ Use unleaded gasoline with a pump octane rating of 86 or higher.

▪ This engine is certified to operate on unleaded gasoline.

▪ Unleaded gasoline produces fewer engine and spark plug deposits and extends exhaust

system life.

▪ Never use stale or contaminated gasoline or an oil/gasoline mixture. Avoid getting dirt or

water in the fuel tank.

10.3 Air filter

The air filter prevents the entry of dust and dirt particles into the carburettor and the

combustion chamber of the motor.

Never operate the generator without the air filter! This would result in highly increased wear of

the engine!

A dirty air filter results in reduced engine efficiency, so the filter cartridge must be cleaned

regularly.(more often when used in dusty environments.)

11 OPERATION

DANGER: Before operation connect your generator to earth! This way you

will avoid static charges (possible electric shock) and will enable protective

devices to respond (e.g. leakage current trip switches) on the appliances

being connected.

Use a shielded conducting cable with a minimum cross-section of 1.5 mm² to connect your

generator to an earthing point (e.g. a water or heating pipe). Connect the conductor to the

earthing connection on your generator and tighten it securely.

CAUTION: The generator has been shipped without engine oil. Fill with oil

or it will not start.

11.1 Starting the engine

NOTE: Before starting the engine, disconnect all loads from the generator.

POWX510 EN

1. Make sure that the AC circuit breaker is in the OFF position. The generator may be hard

to start if a load is connected.

2. Turn the fuel valve lever to the ON position.

3. The choke must be closed if the engine is cold, push the choke rod to the Choke-position.

4. Turn the engine switch to the START position.

5. Pull the starter grip lightly until resistance is felt, then pull briskly.

11.2 Connecting electric tools/appliances

Insert the plug(s) of the electrical appliance(s) into the power socket. (lift the protective lid of

the socket and plug in the load.

CAUTION:

Be sure the electric appliance is turned off before plugging in.

Be sure the total load is within generator rated output.

Be sure the socket load current is within socket rated current.

NOTE:

When the circuit breaker is switched off during operation, the generator was overloaded or a

short circuit occurred (example. connected machine may be defect).

Stop the generator immediately, check the connected power, diminish when it exceeds the

rated generator output. Check the power tool. Allow to cool down for a few minutes before you

switch the circuit breaker back to “ON”.

Most motorized appliances require more than their rated power for startup.

Do not exceed the current limit specified for any one receptacle. If an

overloaded circuit causes the AC circuit breaker or AC circuit protector to

switch OFF, reduce the electricalload on the circuit, wait a few minutes and

then reset the AC circuit breaker or AC circuit protector.

11.3 Stopping

NOTE: Before starting the engine, disconnect all loads from the generator.

1. Turn the AC circuit breaker to the OFF position.

2. Turn the engine switch to the OFF position.

3. Turn the fuel valve lever to the OFF position.

Emergency stopping: Turn the engine switch to “OFF”. The engine will stop

immediately.

11.4 Operating time

Depending on the type you’re using, if you start with a full tank and let it run continuously, your

generator will run approximately :

Fuel tank capacity

Operating time

POWX510

15 liters

+/-11 h

The Petrol level display on top of the fuel tank shows you approximately how much petrol

there is left in the tank.

11.5 Ground system

This generator has a ground system that connects the generator frame components to the

ground terminals in the AC output receptacles. The system is not connected to the AC neutral

wire.

POWX510 EN

11.6 High altitude operation

At high altitude, the standard carburettor air-fuel mixture will be excessively rich.

Performance will decrease, and fuel consumption will increase.

High altitude performance can be improved by installing a smaller diameter main fuel jet in the

carburettor and readjusting the slow tempo screws. If you always operate the generator at

altitudes higher than 1,500 m (5,000 feet) above sea level, have your dealer perform these

carburettor modifications.

Even with suitable carburettor jetting, engine horsepower will decrease approximately 3.5% for

each 300m (1,000 feet) increase in altitude. The effect of altitude on the horsepower will be

greater than this if no carburettor modification is made.

Operation of the generator at an altitude lower than the carburetor is jetted

for may result in reduced performance, overheating, and serious engine

damage caused by an excessively lean air/fuel mixture.

12 MAINTENANCE/CLEANING

12.1 The importance of maintenance.

Good maintenance is essential for safe, economical and trouble-free operation. It will also help

reduce air pollution.

NOTE: Before cleaning or maintenance of the generator, you must switch off the motor and

allow the equipment to cool down!

CLEANING: For cleaning the housing, please use only a lint-free cloth dampened with a

solution of soapy water (solution of washing-up liquid). During cleaning, no water should

penetrate the inside of the generator.

12.2 Maintenance chart

Regular maintenance is most important for the best performance and safe operation.

Regular service

period (2)

Remarks

Pre-

operation

check

Every 2

months

or 20h

Every 3

months

or 50h

Every 6

months

or 100h

Every 12

months

or 300h

Item

Performed at every

indicated month or

operating hour

interval, whichever

comes first.

Engine oil

Check

Change

Air cleaner

Check

Clean

O(1)

Sediment cup

Clean

Spark plug

Clean-

Adjust

Replace

Spark arrester

Clean

Idle speed

Check-

Adjust

POWX510 EN

Valve clearance

Check-

Adjust

Combustion

chamber

Clean

After every 500Hrs.

Fuel tank and filter

Clean

Fuel tube

Check

Every 2 years (replace if necessary)

(1) Service more frequently when used in dusty areas.

(2) For commercial use, log hours of operation to determine proper maintenance intervals.

12.3 Engine oil replacement

Old oil, even in small quantities, must be brought to a suitable collection point for disposal. Old

oil may not be disposed of with household rubbish, waste water, or even to nature.

You need a 12 mm screw wrench and a recipient of sufficiant capacity to catch the oil (see oil

tank capacity) This recipient must fit below the oil drain bolt (if necessary raise the generator

horizontally on blocks or bricks)

▪ Place the, preferably warm machine on a level surface (warm up the engine for several

minutes if cold).

▪ Position the recipient below the position of the oil drain bolt

▪ Remove the oil drain bolt. Drain the oil completely. (Fig. 8)

▪ Check the oil drain plug, gasket, oil filler cap and O-ring. If damaged replace.

▪ Reinstall the oil drain bolt.

▪ Refill engine oil to the upper level. (Fig. 9)

12.4 Air filter (Fig. 10)

A dirty air cleaner will restrict air flow to the carburetor. To prevent carburetor malfunction,

service the air cleaner regularly. Service more frequently when operating the generator in

extremely dusty areas.

1. Unsnap the air cleaner cover clips, remove the air cleaner cover and remove the element.

2. Wash the air cleaner element in a solution of household detergent and warm water, then

rinse thoroughly or wash in non-flammable or high flashpoint solvent. Allow the air

cleaner element to dry thoroughly.

3. Soak the air cleaner element in clean engine oil and squeeze out the excess oil. The

engine will smoke during initial startup if too much oil is left in the air cleaner element.

4. Reinstall the air cleaner element and the cover.

CAUTION: The engine should never run without the air filter element;

excessive piston and/or cylinder wear will result.

12.5 Fuel sediment cup cleaning (Fig. 11)

The sediment cup prevents dirt or water which may be in the fuel tank from entering the

carburetor. If the engine has not been running for a long time, the sediment cup should be

cleaned.

1. Turn the fuel valve lever to the OFF position. Remove the sediment cup, O-ring and filter.

2. Clean the sediment cup, O-ring and filter in nonflammable or high flash point solvent.

3. Reinstall the filter, O-ring and sediment cup.

4. Turn the fuel valve lever ON and check for leaks.

POWX510 EN

12.6 Cleaning / adjusting / replacing spark plug

Easy starting and optimum running of the engine is only possible when the spark plug is clean

and correctly mounted.

▪ Remove the spark plug cable from the spark plug.

▪ Place spark plug key on the spark plug and unscrew it.

▪ The spark plug should be light to dark brown (Standard electrode color: Tan Color). A

black spark plug indicates that the mixture is too rich (choke used for too long, frequent

running for short periods).

▪ Clean the spark plug with a spark plug brush. (This has copper bristles - do not use a steel

brush, otherwise you will damage the spark plug!)

▪ Check the gap between the electrodes with a gauge. It should be between 0.6 and 0.8

mm. If necessary, adjust the gap by carefully bending the electrode. If the gap is too wide,

the ignition spark is too weak or may be completely absent. If the gap is too small, the

electrode becomes burnt, and the plug will not spark reliably.

▪ If the electrode is burnt, or the ceramic insulator is damaged, replace the spark plug. Use

spark plugs with the same charasteristics.

▪ Re-place the spark plug in its housing and screw it tight by hand. The spark plug must

allow itself to be screwed in very easily. - otherwise unscrew again, check the thread for

foreign bodies and screw in again (straight).

▪ Use a plug spanner to tighten the hand-tightened spark plug by a further quarter revolution

and no more, otherwise the thread will be damaged.

▪ Re-place the spark plug cable on the spark plug and ensure that it is seated tightly.

12.7 Muffler screen

The engine and muffler will be very hot after the engine has been run.

Avoid touching the engine and muffler while they are still hot with any part of your body or

clothing during inspection or repair.

▪ Remove the muffler protector and muffler screen.

▪ Clean the carbon deposits out of the muffler screen using a wire brush.

▪ Check the muffler screen. Replace it if damaged.

▪ Install the muffler screen and muffler protector.

13 SERVICE / REPAIRS

▪ Repairs may be carried out by specialized personnel only. For this, use a specialist

workshop.

▪ For repairs, only parts may be used which correspond to the original machine details. This

machine contains electrical and mechanical parts which are essential for protection

against sources of danger.

14 TECHNICAL DATA

GENERATOR

Type

Brush

Voltage Regulator

AVR

Max. Output

2200 W

Rated Output

2000 W

AC Voltage

230V

Frequency

50Hz

Phase

single

Power Factor

Cosφ=1.0

Degree of Protection

IP23M

POWX510 EN

Performance Class

DJ168F

ENGINE

Type

Forced air-cooled, 4 cycle, OHV, Gasoline

Engine

Bore×Stroke mm×mm

68x54

Displacement

196CC

Max. Output

6.5HP/3600rpm

Fuel

Unleaded

EURO 95/98

Fuel tank Capacity

15 liter

Rated Continuous Operation

+/-11 hours

Lubricating oil

SAE10W-30

Lubricating oil Capacity

0.6 liter

Starting System

Recoil Starter

Ignition system

T.C.I.

Spark Plug Type

F7RTC

Dimension L×W×H

720x460x480mm

Dry Weight net

42 kg

15 NOISE

Noise values measured according to relevant standard. (K=3)

Acoustic pressure level LpA

72 dB(A)

Acoustic power level LwA

95 dB(A)

ATTENTION! The sound power level may exceed 85 dB(A), in this case

individual hearing protection shall be worn.

16 TRANSPORT/ STORAGE

▪ If the motor still contains motor oil and/or petrol, it may be transported and stored only in

an upright position

▪ Make sure that the petrol cock is closed and that the motor switch is set to "OFF".

▪ Avoid the sun's direct rays - especially when transporting in a vehicle or mobile home. The

heat can evaporate the petrol in the carburettor, which can escape as an explosive gas.

▪ In the event of shaking or vibrations, (e.g. when crossing agricultural land) a small amount

of petrol can escape through the overflow of the carburettor. Look out for the

corresponding odor.

Long term storage

Long term storage of your machine will require some preventive procedures to guard against

deterioration.

16.1 Drain the fuel

▪ Drain the fuel tank, fuel cock, and carburetor float bowl.

▪ Poor in a cup of SAE 10W30 or 20W40 motor oil.

▪ Shake the tank.

▪ Drain off the excess oil.

▪ ENGINE Pour in about one tablespoon of SAE 10W30 or 20W40 motor oil.

▪ Use the recoil starter to turn the engine over several times (with ignition off).

▪ pull the recoil starter until you feel compression.

▪ Stop pulling.

POWX510 EN

▪ Clean exterior of the generator and apply a rust inhibitor.

▪ Store the generator in a dry, well-ventilated place.

▪ The generator must remain in a horizontal position.

Note: After a long term storage: change the engine oil before starting

▪ Storage place: the environment should be dry and dust-free. If necessary, cover the

generator with a cloth.

17 TROUBLE SHOOTING

Problem

Possible cause

Solution

The engine will not start

Is there fuel in the tank?

Refill the fuel tank.

Is there enough oil in the

engine?

Add the recommended oil.

Is the spark plug in good

condition?

Readjust gap and dry the

spark plug.

Replace it if necessary.

Is the fuel reaching the

carburetor?

Clean the fuel sediment cup.

No electricity at the AC

receptacles

Is the AC circuit breaker

ON?

Turn the AC circuit breaker

ON.

Check the electrical

appliance or equipment for

any defects;

Replace the electrical

appliance or equipment.

Take the electrical appliance

or equipment to an electrical

shop for repair.

18 WARRANTY

▪ This product is warranted for a 36-month period effective from the date of purchase by the

first user.

▪ This warranty covers all material or production flaws excluding : batteries, chargers,

defective parts subject to normal wear & tear such as bearings, brushes, cables, and

plugs, or accessories such as drills, drill bits, saw blades, etc. ; damage or defects

resulting from maltreatment, accidents or alterations; nor the cost of transportation.

▪ Damage and/or defects resulting from inappropriate use also do not fall under the

warranty provisions.

▪ We also disclaim all liability for any bodily injury resulting from inappropriate use of the

tool.

▪ Repairs may only be carried out by an authorised customer service centre for Powerplus

tools.

▪ You can always obtain more information at the number 00 32 3 292 92 90.

▪ Any transportation costs shall always be borne by the customer, unless agreed otherwise

in writing.

▪ At the same time, no claim can be made on the warranty if the damage of the device is the

result of negligent maintenance or overload.

▪ Definitely excluded from the warranty is damage resulting from fluid permeation, excessive

dust penetration, intentional damage (on purpose or by gross carelessness), inappropriate

usage (use for purposes for which the device is not suitable), incompetent usage (e.g. not

following the instructions given in the manual), inexpert assembly, lightning strike,

erroneus net voltage. This list is not exhaustive.

POWX510 EN

▪ Acceptance of claims under warranty can never lead to the prolongation of the warranty

period nor commencement of a new warranty period in case of a device replacement.

▪ Devices or parts which are replaced under the warranty therefore remain the property of

Varo NV.

▪ We reserve the right to reject a claim whenever the purchase cannot be verified or when it

is clear that the product has not been properly maintained. (Clean ventilation slots, carbon

brushes serviced regularly, etc.).

▪ Your purchase receipt must be kept as proof of date of purchase.

▪ Your appliance must be returned undismantled to your dealer in an acceptably clean state,

(in its original blow-moulded case if applicable to the unit), accompanied by proof of

purchase.

19 ENVIRONMENT

Should your appliance need replacement after extended use, do not dispose of it

with the household refuse, but in an environmentally safe way.

Waste of electrical products should not be disposed of with household waste.

Please recycle where facilities exist. Check with your Local Authority or retailer for

recycling advice.

20 DECLARATION OF CONFORMITY

VARO N.V. – Joseph Van Instraat 9 – BE2500 Lier – Belgium, declares that,

Product Generator

Trade mark PowerPlus

Model: POWX510

Is in conformity with the essential requirements and other relevant provisions of the applicable

European Directives, based on the application of European harmonized standards. Any

unauthorized modification of the apparatus voids this declaration.

European Directives (including, if applicable, their amending directives);

2006/42/EC

2014/30/EU

2000/14/EC Annex VI LwA 92dB(A) / 95dB(A)

Testing Authority: SNCH – Sandweiler

European harmonized standards (including, if applicable, their amendments);

EN ISO 8528-13 2016

EN55012-1 : 2007

EN61006-1 : 2007

The undersigned acts on behalf and under the power of attorney of the company

management,

Philippe Vankerkhove

Certification Manager

Lier, 28/11/2018

Powerplus POWX510 Owner's manual

Related papers

Other documents