2. National
  3. Confide Chair Ganging

National Confide Chair Ganging Assembly Instruction

  • Hello! I am an AI chatbot trained to assist you with the National Confide Chair Ganging Assembly Instruction. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the purpose of this document?
    What tools do I need to assemble the Confide Chair?
    How do I remove the screws holding the connection bars?
    What should I do with the screws and connection bars after removing them?
    How do I determine which side of the existing chair to use for the add-on chair?
    How do I remove the finger bracket cover?
    How do I attach the connection bars to the add-on chair?
    How do I attach the add-on chair to the existing chair?
    How do I attach the finger bracket of the add-on chair to the finger bracket of the existing chair?
    How do I attach the finger bracket cover?
Confide Chair Ganging
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent. If you have any
questions concerning these instructions, please call National Customer Service 800.482.1717.
Assembly Instruction
2
Telephone 800.482.1717
Fax 812.482.8800
www.NationalOfficeFurniture.com
Part #2421495
Rev,A
Printed in U.S.A
© 2012 Kimball International, Inc.
Recommended Tools
• #3 Phillips Head Screwdriver
Package Contents Qty.
• #1/4"-20 x 3/4" Truss Head
Screw 4 per bar
• #1/4"-20 x 1/2" Flat Head
Screw 2
• Connection Bar
2 per add-on side
Place the connection bars into the open
exposed beam ends of the add-on chair,
aligning mounting holes. Attach with
two (2) 1/4"-20 x 3/4" truss head
screws per connection (Figure C).
Figure AA
3
Determine which side of existing chair
for add-on chair. Remove the inserted
caps from the under-seat beam on the
determined side of existing chair.
NOTE: Under-seat beam caps are located
on the bottom side of the chair as shown
in Figure AA.
Figure C
4
Remove the finger bracket cover from
the back of the add-on side of existing
chair. To disengage press down and out
on the top tab (Figure B).
Caps
Figure B
Bars
Screws
1
Figure A
Remove the screws holding the connection
bars using a #3 phillips head screwdriver
(Figure A).
Note: Keep the screws and connection bars
for later use.
Screws
Confide Chair Ganging
Assembly Instruction
Proper product installation, in accordance with these instructions, is the responsibility of the installing agent. If you have any
questions concerning these instructions, please call National Customer Service 800.482.1717.
Align the finger bracket of the add-on
chair to the finger bracket of the existing
chair. Attach with two (2) 1/4"-20 x 1/2"
flat head screws (Figure E).
Figure E
6
7
To attach the finger bracket cover,
align the bottom tab in the slot, press
down and in to engage the top tab
(Figure F).
Figure F
Attach finger bracket
with (2) 1/4"-20 x 1/2"
flat head screws.
5
Attach the add-on chair to the existing
chair by placing the connection bars on
the add-on chair into the open exposed
beam ends of the existing chair, align
the mounting holes. Attach with two (2)
1/4"-20 x 3/4" truss head screws for
each connection bar.
NOTE: Figure D shows the bottom side
of the chairs, where the under-seat
beams and connection bars are located.
Figure D
Attach with two (2) 1/4-20 x
3/4" truss screws for each bar.
/