Hyundai G3F57-AC200 Owner's manual

Brand: Hyundai

Model: G3F57-AC200

Category: Remote starters

Type: Owner's manual

Regular Key

Genuine Parts

REMOTE START OWNER’S GUIDE

WARNING

It is the responsibility of the vehicle operator to ensure that their vehicle is parked in a safe and responsible manner.

1. When leaving the vehicle, it is the user’s responsibility to ensure that the gearshift lever is in “Park” in order to avoid accidents

upon remote starting. (Note: Make sure that the vehicle cannot start in “Drive”.)

2. It is the user’s responsibility to ensure that the remote starter is disabled or put into valet mode before servicing.

FCC COMPLIANCE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate this device.

CAUTION:

REMOTE START OWNER’S GUIDE

INTRODUCTION

TABLE OF CONTENTS:

Congratulations on your purchase of a Remote Start system. This easy-to-use manual details the operation

instructions and benefits of the Remote Start System. Should you have questions regarding this system that this

manual does not address, please contact your local dealer.

Using the Remote Start

Description of Remote Start Fob

Button Functions

Remote-Starting your Vehicle

Remote-Starting

Driving Off

Vehicle Presets

Heater

Windshield Wipers and Headlights

Remote Start Features

Remote Start Error Diagnostic

Valet/Service Mode

Pairing Remote Start Fob

Battery Replacement

for Remote Start Fob

Troubleshooting Poor Transmitter Range

Remote Start Run Time

Using The Remote Control

Description of Remote Start Fob

Button Functions

Note: Make sure to press button only after LED lighting ends to activate each feature properly.

kcoLemit 1 sserP

rood s’revird kcolnU semit 2 sserP

Press 2 times x 2 Unlock all doors

pots/trats etomeRsdnoces 2 dloH

Lock/Unlock

Note: Press the button 1 time on the

transmitter to lock the vehicle.

Press the button 2 times to unlock the

driver’s door, and 2 additional times to

unlock all doors.

START/STOP:

Note : Remote Engine Start -

Press the button 1 time and then,

within 3 seconds, press and hold

the button for 2 seconds.

Remote Engine Stop - Press

and hold the button for 2 seconds.

Lock, Unlock and Remote

Starting icon is displayed with

one LED color.

Button Image Button LED/icon Feature

Driving Off

With the vehicle running remotely, press the button 2 times to unlock the driver’s door, enter the vehicle and perform the

following to drive off:

1) Insert the vehicle’s key to the IGNITION, turn to the ON position and press the brake pedal.

The vehicle is now ready to drive.

Note: The Factory Key Fob will NOT

function during Remote Start operation.

The engine will shut off if either of the following occurs;

1) The drive off procedure is not initiated within 30 seconds of opening any door, within 50 seconds of opening tailgate / trunk.

2) The brake is pressed without the vehicle key in the ignition in the ON position.

If the vehicle turnns off, simply start the vehicle using the normal starting procedure as detailed in the vehicle’s owner’s manual.

Remote Starting your Vehicle

Remote Starting

Using Remote Start Fob

1. Press button 1 time, the lock icon will display. Within 3 seconds, press and hold the button for 2 seconds,

the key icon will flash and the vehicle will start.

2. Remote Stop - Press and hold button for 2 seconds. The key icon will flash and the engine will turn off.

Note: Make sure to press a button only after LED lighting ends to activate each feature properly.

Vehicle Presets

Heater

When leaving the vehicle, it is recommended to preset the climate controls in preparation for the next remote start. The climate

controls for the fan should not be left on HIGH. It is recommended to leave the setting on LOW or MEDIUM instead.

Windshield Wipers, Headlights

Certain vehicles require the windshield wipers and headlights circuits to become energized while running under remote start. When

leaving the vehicle you must ensure that the windshield wipers and headlights switches are OFF. Leaving the headlights switch ON

on certain types of vehicles could cause them to remain ON even after remote starter shutdown, resulting in a dead battery.

Leave Windshield Wipers off to avoid damaging the wipers/motor with remote start.

Remote Start Features

Remote Start Error Diagnostic

If remote engine start fails, the vehicle will not start and the horn will sound the corresponding number of times to identify the

reason for the failed remote start listed below;

Number of horn chirps Remote Start Error

1 Hood open

2 KEY IN or Ignition ON

3 Valet mode

4 Brake Applied

5 Tailgate/Trunk open

6 Door open

Valet/Service Mode

Valet/Service mode is used to prevent the system from unexpectedly starting the engine while being serviced.

When your vehicle is in Valet Mode, the remote starter functions are disabled. If the vehicle needs to be serviced, or if you park it

indoors, the Valet Mode will prevent the engine from being remote-started accidentally.

Remote Start Features

To Engage Valet Mode/Service Mode:

1) Insert the vehicle’s key to the IGNITION, turn to the ON position.

2) Press and hold the vehicle brake pedal.

3) Press and hold the remote button for 2 seconds, Vehicle’s exterior lights will flash and horn will sound once.

The valet mode is engaged.

To Exit Valet Mode/Service mode (Return the system to its normal operating mode):

1) Insert the vehicle’s key to the IGNITION, turn to the ON position.

2) Press and hold the vehicle brake.

3) Press and hold the remote button for 2 seconds, Vehicle’s exterior lights will flash and horn will sound twice.

The valet mode will be off .

Pairing Remote Start Fob

The Remote Start Fobs in the Remote Start Kit are paired with the main module at the time of production.

There is no need to pair the Fobs at the time of the first installation.

1. Pairing requirement cases

Key loss or replacement due to malfunction

Replacement of main controller in a vehicle

Purchase of spare Remote Start Fob

2. Pairing conditions

1) Open driver’s door and tailgate/trunk.

2) Insert the key into the ignition. Turn the key from OFF to ON position 5 times within 5 seconds.

3) Within 5 seconds, Press button on the 1st Remote Start Fob 1 time.

4) After registering the 1st Remote Start Fob, within another 5 seconds, Press button on the next Remote Start Fob 1 time.

5) Verify that all Fobs are functioning correctly by performing Lock / Unlock function.

NOTE:

1) System can recognize up to 3 remotes.

2) If a new Fob, or additional Fob, is needed later, the Fob pairing process should be done with the original Fob,

or oldest available Fob.

Pairing Remote Start Fob

REMOTE

START

FOB X1

Battery Replacement for Remote Start Fob

The two (2) 3-Volt Lithium battery (Model: CR2025) supplied in your remote control transmitter will last approximately 3 years,

depending on usage. When the batteries begin to weaken, the Remote Start Fob LEDs will no longer flash per operation and the

range of the remote transmission distance will be decreased. Replacement batteries are available at local electronics stores.

Follow the instructions below to change the remote control battery:

1. Use a coin or small screwdriver to pry the remote control halves apart.

2. Remove the old batteries and replace with 2 new CR2025 batteries.

3. Be sure to observe the (+) sign when inserting the new batteries.

4. Before assembling the transmitter case, you should test the remote control by performing a remote start operation.

Note: Recycle or dispose of the old batteries according to local laws or regulations.

Procedure:

1. Unlock the doors using the remote start fob or factory transmitter to disarm the vehicle.

2. Driver’s door must be open, engine stopped, ignition ON, trunk open and hood open.

3. Press and hold the remote start fob button for 2 seconds.

Note: Lights or Horn of vehicle will activate according to the following chart.

Troubleshooting Poor Transmitting Range

Many factors may affect the operating range of the transmitter. Some of these are:

The condition of the batteries in the transmitter.

The operating environment (for example: downtown radio-frequency noise, airports, cellular phone towers, etc).

Metal in the area of the vehicle of transmitter. This includes the vehicle itself.

The shape of the roof and A-pillars causes considerable radio-frequency interference.

The orientation of the vehicle to user. The best range is facing the vehicle's front.

The worst range is facing the vehicles right or left side.

The orientation of the user to the vehicle. Facing the vehicle’s front offers the best range.

The amount of other vehicles in the area of the target vehicle.

The method of using the transmitter. Always hold the transmitter high, approximately at shoulder height.

Automatic Engine Start Repeat

Remote Start is programmed to repeat the engine start sequence two (2) more times after ten (10) seconds if the engine start fails

because of a low vehicle battery.

Remote Start Run Time

Changing Remote Start Run Time Setting

The remote start system is preset to the 10 Minutes (default) runtime setting and can not be increased.

The standard runtime can be stopped at anytime using the remote start fob or factory transmitter.

Number of Horn Honks or Lights Flashes Setting

10 Minutes (default)1 Time

2 Times 5 Minutes

Hyundai G3F57-AC200 Owner's manual

Brand: Hyundai

Model: G3F57-AC200

Category: Remote starters

Type: Owner's manual

Download PDF

report

Hyundai G3F57-AC200 Owner's manual

Hyundai G3F57-AC200 Owner's manual

Other documents