GE WSM2420D0CC Installation guide

Brand: GE

Model: WSM2420D0CC

Category: Washer dryers

Type: Installation guide

This manual is also suitable for

WSM2420

24" (61 CM) ELECTRICWASHER/DRYER

INSTALLATIONINSTRUCTIONS

TableofContents

WASHER/DRYER SAFETY ....................................... 1

INSTALLATION INSTRUCTIONS ............................. 2

Tools and Parts ....................................................... 2

Alternate Parts ........................................................ 2

Location Requirements ......................................... 2

Drain System .......................................................... 3

Electrical Requirements .......................................... 4

Electrical Connection .............................................. 5

Venting Requirements ............................................ 9

Install Leveling Legs ............................................. 10

Remove Foam Packing ............................... 10

Connect Drain Hose .................................... 10

Connect Inlet Hoses .................................... 11

Secure Drain Hose ...................................... 12

Plan Vent System ........................................ 12

Install Vent System ...................................... 13

Level Washer/Dryer ..................................... 14

Connect Vent ............................................... 14

Complete Installation .................................. 14

WASHER/DRYERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

8557471A

INSTALLATIONINSTRUCTIONS

Gather the required tools and parts before starting installation.

Read and follow the safety instructions provided with any tools

listed here.

Tools needed:.

#2 Phillips and flat-blade • Wire stripper (direct wire

screwdriver installations)

Adjustable wrench that • Knife

opens to 1" (2.5 cm) or

9/16"(14 mm) open-end

wrench (for adjusting

dryer feet)

Level

1/4"nut driver or socket

wrench • Scissors

• Vent clamps

• Caulking gun and

compound (for installing

new exhaust vent)

• Pliers

• Wood block (for leveling) • Tin snips (for new vent

• Ruler or measuring tape installations)

Parts supplied:

Remove parts package from the washer basket. Check that all

parts were included.

A C D

Your installation may require additional parts. For ordering

information, please refer to your Use and Care Guide.

If You Have You Will Need to Buy

Laundry tub or Sump pump system (if not already

standpipe taller than available)

96" (2.4 m)

1" (2.5 cm) diameter 2" (5 cm) diameter to 1" (2.5 cm)

standpipe diameter standpipe adapter, Part

Number 3363920

Overhead sewer Standard 20 gal. (76 L) 34" (86.4 cm)

tall drain tub or utility sink and sump

pump (available from local plumbing

suppliers)

Floor drain Siphon break, Part Number 285320,

additional drain hose, Part Number

285702 and connector kit,

Part Number 285442

Drain hose too short Drain hose, Part Number 285664 and

connector kit, Part Number 285442

Lint clogged drain Drain protector, Part Number 367031

Water faucets 2 longer water fill hoses:

beyond reach of fill 6 ft (1.8 m) Part Number 76314,

hoses 10 ft (3.0 m) Part Number 350008

E _JF G

A. Water inlet hoses (2)

B.Inlet hose flat washers (4)

C. Rear leveling legs (2)

D. Front leveling legs (2)

E. Plastic strap

F Drain hose

G. Yellow, single wire hose clamp

H. Silver, double wire hose clamp

Parts needed:

Check local codes. Check existing electrical supply and venting,

and see "Electrical Requirements" and "Venting Requirements"

before purchasing parts.

Mobile home installations require metal exhaust system hardware

available for purchase from the dealer from whom you purchased

your washer/dryer. For further information, please reference your

Use and Care Guide.

Explosion Hazard

Keep flammabme materiaBs and vapors, such as

gasoline, away from dryer.

Failure to do so can result in death, expmosion, or fire.

You will need

• A location that allows for proper exhaust installation. See

"Venting Requirements."

• Aseparate30-amp circuit.

• A grounded electrical outlet located within 2 ft (61 cm) of

either side of the washer/dryer. See "Electrical Requirements."

• Asturdyfloortosupportthewasher/dryerweight(washer/

dryer,waterandload)of500Ibs(226.8kg).

• Alevelfloorwithamaximumslopeof1"(2.5cm)underentire

washer/dryer.Clothesmaynottumbleproperlyandautomatic

sensorcyclesmaynotoperatecorrectlyifwasher/dryerisnot

level.Installingoncarpetisnotrecommended.

• Awaterheatersettodeliver120°F(49°C)watertothewasher.

• Hotandcoldwaterfaucetslocatedwithin4ft(1.2m)ofthe

hotandcoldwaterfillvalves,andwaterpressureof5-100psi

(34.5-689.6kPa).

Thewasher/dryermustnotbeinstalledorstoredinanareawhere

itwillbeexposedtowaterand/orweather.

Donotoperateyourwasherintemperaturesatorbelow

32°F(0°C).Somewatercanremaininthewasherandcancause

damageinlowtemperatures.See"CareandCleaning"inyour

UseandCareGuideforwinterizinginformation.

Donotoperateyourdryerattemperaturesbelow45°F(7°C).At

lowertemperatures,thedryermightnotshutoffattheendofan

automaticcycle.Thiscanresultinlongerdryingtimes.

Checkcoderequirements.Somecodeslimit,ordonotpermit,

installationofthewasher/dryeringarages,closets,mobilehomes,

orsleepingquarters.Contactyourlocalbuildinginspector.

Installation Clearances

The location must be largeenoughto allow the door to open fully.

Washer/Dryer Dimensions

15%"

(39.05 cm)

Rear clearance may be 0" when house exhaust system is lined

up directly with dryer exhaust.

O oo o_

(9®} (e0.64cm)(0cm)

÷l 1"N27,J0"+(

(2.5_) (69.22ore)

l_(9crn)[_ 3_,(z6cm)

(310cm2)[

24in"_-4

0_sc_t[ _ "(7=6cm)

(14®)

A. Recessed area

B. Side view - closet or confined area

C. Closet door with vents

Mobile Home - Additional Installation Requirements

This washer/dryer is suitable for mobile home installations.

The installation must conform to the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction and

Safety, Title 24, HUD Part 280).

Mobile home installations require:

• Metal exhaust system hardware which is available for

purchase from your dealer.

• Special provisions must be made in mobile homes to

introduce outside air into the dryer. The opening (such as a

nearby window) should be at least twice as large as the dryer

exhaust opening.

71 _A"

(182.25 cm)

*27 ¼"

(69.22 ore)

23 7/8"

cm)

*Most installations require a minimum 5W' (14 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting

Requirements."

Minimum installation spacing for recessed area or closet

installation

The following dimensions shown are for the minimum spacings

allowed.

• Additional spacing should be considered for ease of

installation and servicing.

• Additional clearances might be required for wall, door and

floor moldings.

• Additional spacing of 1" (2.5 cm) on all sides of the washer/

dryer is recommended to reduce noise transfer.

• For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

The washer/dryer can be installed using the standpipe drain

system (floor or wall), the laundry tub drain system, or the floor

drain system. Select the drain hose installation method you need.

See "Alternate Parts."

Standpipe drain system - wall or floor (views A & 13)

The standpipe drain requires a minimum diameter standpipe of

2" (5 cm). The minimum carry-away capacity can be no less than

17 gal. (64 L) per minute. A 2" (5 cm) diameter to 1" (2.5 cm)

diameter standpipe adapter kit is available. See "Alternate Parts."

The top of the standpipe must be at least 39" (99 cm) high and no

higher than 96" (2.4 m) from the bottom of the washer.

Laundry tub drain system (view (3}

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top

of the laundry tub must be at least 34" (86.4 cm) above the floor

and no higher than 96" (2.4 m) from the bottom of the washer.

Floor drain system (view D)

The floor drain system requires a siphon break that may be

purchased separately. See "Alternate Parts."

Thesiphonbreakmustbeaminimumof28"(71cm)fromthe

bottomofthewasher.Additionalhosesmightbeneeded.

AULlisted30amppowersupplycord,rated120/240volt

minimum.ThecordshouldbetypeSRDorSRDTandbeat

least4ft(1.22m)long.Thewiresthatconnecttothedryer

mustendinringterminalsorspadeterminalswithupturned

ends.

• AULlistedstrainrelief.

If your outlet looks like this:

It is your responsibility

• To contact a qualified electrical installer.

• To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

• To supply the required 3 or 4 wire, single phase, 120/240-volt,

60-Hz., AC-only electrical supply (or 3 or 4 wire, 120/208-volt

electrical supply, if specified on the serial/rating plate) on a

separate 30-amp circuit, fused on both sides of the line. A

time-delay fuse or circuit breaker is recommended. Connect

to an individual branch circuit. Do not have a fuse in the

neutral or grounding circuit.

• Do not use an extension cord.

• If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

Electrical Connection

To properly install your washer/dryer, you must determine the type

of electrical connection you will be using and follow the

instructions provided for it here.

• This dryer is manufactured ready to install with a 3-wire

electrical supply connection. The green cabinet-grounding

conductor is permanently connected to the neutral conductor

(white wire) within the dryer. If the dryer is installed with a

4-wire electrical supply connection, the green cabinet-

grounding conductor must be removed from the external

ground connector (green screw), and secured under the

neutral terminal (center or white wire) of the terminal block.

When the green cabinet-grounding conductor is secured

under the neutral terminal (center or white wire) of the terminal

block, the dryer cabinet is isolated from the neutral conductor.

• If local codes do not permit the connection of a cabinet

ground connector to the neutral wire, see "Optional 3-wire

connection" section.

• Use a 4-wire conductor cord when the dryer is installed in a

mobile home or an area where local codes do not permit

grounding through the neutral.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with clothes

dryers. The kit should contain:

4-wire receptacle (14-30R)

Then choose a 4-wire power supply cord with ring or spade

terminals and UL listed strain relief. The 4-wire power supply cord,

at least 4 ft (1.22 m) long, must have 4, 10-gauge copper wires

and match a 4-wire receptacle of NEMA Type 14-30R. The ground

wire (ground conductor) may be either green or bare. The neutral

conductor must be identified by a white cover.

If your outlet looks like this:

3-wire receptacle (10-30R)

Then choose a 3-wire power supply cord with ring or spade

terminals and UL listed strain relief. The 3-wire power supply cord,

at least 4 ft (1.22 m) long, must have 3, 10-gauge copper wires

and match a 3-wire receptacle of NEMA Type 10-30R.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

• Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), protected with flexible metallic conduit. All

current-carrying wires must be insulated.

• 10-gauge solid copper wire (do not use aluminum).

• At least 5 ft (1.52 m) long.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected washer/dryer:

This washer/dryer must be grounded. Hnthe event of

malfunction or breakdown, grounding will reduce the risk of

electric shock by providing a path of least resistance for

electric current. This washer/dryer uses a cord having an

equipment-grounding conductor and a grounding plug. The

plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with alI local

codes and ordinances.

[] For a permanently connected washer/dryer:

This washer/dryer must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the washer/dryer.

WARNING-" Hmproper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative or

personnel if you are in doubt as to whether the washer/dryer

is properly grounded. Do not modify the plug on the power

supply cord: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

PowerSupplyCord DirectWire

Fire Hazard

Use a new UL misted30 amp power supply cord.

Use a UL misted strain retief,

Disconnect power before making emectrical connections,

Connect neatraB wire (white or center wire) to center

terminal (silver),

Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining 2 suppmy wires to remaining

2 terminals (gored).

Securemy tighten aimelectrical connections,

Failure to de so can resumt in death, fire, or

electrical shock,

1. Disconnect power.

2. Remove the hold-down screw and terminal block cover.

.... • • • j

A. Center silver-colored terminal block screw

B. Hold-down screw

C. Terminal block cover

D. Internal ground conductor screw

Fire Hazard

Use 10 gauge somid copper wire,

Use a UL mistedstrain relief,

Disconnect power before making emectricaJ connections.

Connect neutral wire (white or center wire) to center

terminal (simver).

Ground wire (green or bare wire) must be connected to

green ground connector,

Connect remaining 2 suppmy wires to remaining

2 terminals (gold).

Securety tighten aimeBectrica{ connections.

FaiJure to do so can resuJt in death, fire, or

emectrical shock.

3. Assemble a 3/4"(1.9 cm) UL listed strain relief (UL marking on

strain relief) into the hole below the terminal block opening.

Tighten strain relief screws just enough to hold the two clamp

sections together, Put power supply cord through the strain

relief, The strain relief should have a tight fit with the dryer

cabinet.

Now complete installation following instructions for your type

of electrical connection:

4-wire (recommended)

3-wire (if 4-wire is not available)

Electrical Connection Options

If your home has: And you will be Go to Section

connecting to:

4-wire receptacle A UL listed, 4-wire connection:

(NEMA Type 14-30R) 120/240 volt Power supply cord

minimum,

30 amp, dryer

power supply

cord*

4-wire direct A fused 4-wire connection:

disconnect or Direct Wire

circuit breaker

box*

1. Remove center terminal block screw.

2. Remove neutral grounding wire (green with yellow stripes)

from internal ground conductor screw. Fasten it under center,

silver-colored terminal block screw.

,,r

3-wire receptacle A UL listed,

(NEMA type 10-30R) 120/240 volt

_) minimum,

30 amp, dryer

power supply

cord*

3-wire connection:

Power supply cord

3-wire direct A fused 3-wire connection:

disconnect or Direct Wire

circuit breaker

box*

*If local codes do not permit the connection of a frame-grounding

conductor to the neutral wire, go to "Optional 3-wire connection"

section.

4-wire connection: Power supply cord

IMPORTANT: A 4-wire connection is required for all mobile

homes and where local codes do not permit the use of 3-wire

C D

connections.

E G

A. 4-wire receptacle (NEMA type 14-30R)

B. 4-prong plug

C. Ground prong

D. Neutral prong

E.Spade terminals with upturned ends

F. _" (1.9 cm) UL listed strain relief

G. Ring terminals

A. Center silver-colored terminal block screw

B. Neutral grounding wire (green with yellow stripes)

C. Internal ground conductor screw

3. Move the green painted screw from the internal to the external

ground conductor location. Connect ground wire (green or

bare) of power supply cord to external ground conductor

screw. Tighten screw.

4. Connect neutral wire (white or center wire) of power supply

cord under center screw of the terminal block. Tighten screw.

,¢

............... C

A. Neutral wire (white or center wire)

B. Center silver-colored terminal block screw

C. Neutral grounding wire (green with yellow stripes)

D. External ground conductor screw

E.Green or bare wire of power supply cord

F Internal ground conductor location

G. 3/4"(1.9 cm) UL listed, strain relief

5. Connect the other wires to outer terminal block screws.

Tighten screws.

6. Tighten strain relief screws.

7. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

4-wire connection: Direct Wire

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire

connections.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer

can be moved if needed.

Strip 5" (12.7 cm) of outer covering from end of cable, leaving

bare ground wire at 5" (12.7 cm). Cut 11/2'' (3.8 cm) from

3 remaining wires. Strip insulation back 1" (2.5 cm). Shape ends of

wires into a hook shape.

Move the green painted screw from the internal to the external

ground location. Connect ground wire (green or bare) of power

supply cable to external ground conductor screw. Tighten

screw,

Place the hooked end of the neutral wire _white or center wire)

of power supply cable under the center screw of terminal

block (hook facing right), Squeeze hooked end together.

Tighten screw.

When connecting to the terminal block, place the hooked end of

the wire under the screw of the terminal block (hook facing right),

squeeze hooked end together and tighten screw. See example

below,

1. Remove center terminal block screw.

2. Remove appliance ground wire (green with yellow stripes)

from internal ground conductor screw. Fasten it under center,

silver-colored terminal block screw.

A. Neutral wire (white or center wire)

B. Center silver-colored terminal block screw

C. Neutral grounding wire (green with yellow stripes)

D. External ground conductor screw

E. Green or bare wire of power supply cable

F. Internal ground conductor location

G. _A"(1.9 cm) UL listed, strain relief

Place the hooked ends of the other power supply cable wires

under the outer terminal block screws (hooks facing right).

Squeeze hooked ends together. Tighten screws.

J .....

A. Center silver-colored terminal block screw

B. Neutral grounding wire (green with yellow stripes)

C. Internal ground conductor screw

6. Tighten strain relief screws,

7. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

3-wire connection: Power supply cord

Use where local codes permit connecting cabinet-ground

conductor to neutral wire.

G F

A. 3-wire receptacle (NEMA type 10-30R)

B. 3-wire plug

C. Neutral prong

D. Spade terminals with up turned ends

E. ¾" (1.9 cm) UL llsted strain relief

F Ring terminals

G. Neutral (white or center wire)

Loosen or remove center terminal block screw.

Connect neutral wire (white or center wire) of power supply

cord to the center, silver-colored terminal screw of the terminal

block. Tighten screw.

A. Neutral wire (white or center wire)

B. Center silver-colored terminal block screw

C. Neutral grounding wire (green with yellow stripes)

D. Internal ground conductor screw

E.3/_,,(1.9 cm) UL listed, strain relief

3. Connect the other wires to outer terminal block screws.

Tighten screws.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

3-wire connection: Direct Wire

Use where local codes permit connecting cabinet-ground

conductor to neutral wire.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer

can be moved if needed.

Strip 3W' (8.9 cm) of outer covering from end of cable. Strip

insulation back 1" (2.5 cm). Ifusing 3-wire cable with ground wire,

cut bare wire even with outer covering. Shape ends of wires into a

hook shape.

When connecting to the terminal block, place the hooked end of

the wire under the screw of the terminal block (hook facing right),

squeeze hooked end together and tighten screw.

Loosen or remove center terminal block screw.

Place the hooked end of the neutral wire (white or center wire)

of power supply cable under the center screw of terminal

block (hook facing right). Squeeze hooked end together.

Tighten screw.

E D

A. Neutral wire (white or center wire)

B. Center silver-colored terminal block screw

C. Neutral grounding wire (green with yellow stripes)

D. Internal ground conductor screw

E. _/_"(1.9 cm) UL listed, strain relief

3. Place the hooked ends of the other power supply cable wires

under the outer terminal block screws (hooks facing right).

Squeeze hooked ends together. Tighten screws.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

Optional 3-wire connection

Use for direct wire or power supply cord where local codes do

not permit connecting cabinet-ground conductor to neutral

wire.

1. Remove center terminal block screw.

2. Remove neutral grounding wire (green with yellow stripes)

from internal ground conductor screw. Connect appliance

ground wire and the neutral wire (white or center wire) of

power supply cord/cable under center, silver-colored terminal

block screw. Tighten screw.

3. Connect the other wires to outer terminal block screws.

Tighten screws.

Tighten strain relief screws.

Move the green painted screw from the internal to the external

ground conductor location. Connect a separate copper

ground wire from the external ground conductor screw to an

adequate ground.

A ............................................................. B

A. Neutral wire (white or center wire)

B. Neutral grounding wire (green with yellow stripes)

C. External ground conductor screw

D. Grounding path determined by a qualified electrician

E. Internal ground conductor location

Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent,

Fai{ure to follow these instructions can resu}t in death

or fire°

WARNING: To reduce the risk of fire, this washer/dryer

MUST BE EXHAUSTED OUTDOORS.

• The dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, or a concealed space of a building,

• Do not use an exhaust hood with a magnetic latch.

• Do not install flexible metal vent in enclosed walls, ceilings or

floors,

• Use clamps to seal all joints. Exhaust vent must not be

connected or secured with screws or other fastening devices

which extend into the interior of the duct. Do not use duct

tape.

IMPORTANT: Observe all governing codes and ordinances,

_mproper venting can cause moisture and _int to collect

indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint,

wallpaper, carpets, etc.

[] Housec{ean[ng problems and health problems=

Use a heavy metal vent. Do not use plastic or metal foil vent.

Rigid metal vent is recommended to prevent crushing and kinking.

Flexible metal vent must be fully extended and supported when

the washer/dryer is in its final position. Remove excess flexible

metal vent to avoid sagging and kinking that may result in reduced

airflow and poor performance.

An exhaust hood should cap the vent to prevent rodents and

insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground or

any object that may be inthe path of the exhaust (such as flowers,

rocks or bushes, etc.).

If using an existing vent system, clean lint from the entire length of

the system and make sure exhaust hood is not plugged with lint.

Replace any plastic or metal foil vent with rigid metal or flexible

metal vent.

Excessive Weight Hazard

Use two or more people to move and install

washer/dryer.

Failure to do so can result in back or other injury.

To protect the floor, use a large flat piece of cardboard from the

shipping carton. Gently place the washer/dryer on its side, on the

cardboard.

Install the rear leveling legs

1. Push legs into holes in rear corners until they snap into place.

2. Check adjustability of rear legs by pushing in one leg. The

other leg should come out. Check both legs. If they do not

move freely, repeat Step 1.

Install the front leveling legs

1. Examine the front leveling legs. Find the diamond marking.

2. Screw front legs by hand, into the holes in the triangular

braces in the front corners. Use wrench to finish turning the

legs until the diamond marking is no longer visible.

3. Slowly stand the washer/dryer upright.

1. Open the washer lid. The latch under the dryer will keep the lid

open.

2. Pull the foam packing ring out of the washer.

NOTE: Keep the foam ring and use it when transporting your

washer/dryer. This packing material is used to keep the washer

tub stable during transport.

Proper connection of the drain hose protects your floors from

damage due to water leakage. To prevent the drain hose from

coming off or leaking, it must be installed according to the

following instructions:

IMPORTANT: To ensure proper installation, this procedure must

be followed exactly.

1. Check the drain hose to see whether it is the proper length.

2. Wet the inside of the straight end of the drain hose with tap

water.

IMPORTANT: Do not use any lubricant other than water.

3. Squeeze ears of the silver, double-wire clamp with pliers to

open. Place clamp over the straight end of the drain hose

1A"(6.4 mm) from the end.

4. Open clamp. Twist hose back and forth while pushing onto

drain connector on the side of the washer/dryer. Continue until

hose contacts the ribbed stops on the cabinet.

5. Place clamp over the area marked "CLAMR" Release clamp.

For laundry tub or standpipe drain systems

1. Open the yellow, single-wire clamp and slide over the hooked

end of the drain hose to secure the rubber and corrugated

sections together.

A. Hooked end

B, Drain hose

Put the hooked end of drain hose into laundry tub or

standpipe. Rotate hook to eliminate kinks.

To prevent drain water from going back into the washer:

• Do not straighten hooked end of the drain hose and force

excess drain hose into standpipe. Hose should be secure

but loose enough to provide a gap for air.

• Do not lay excess hose on the bottom of the laundry tub.

For use with floor drain

Remove the drain hose hook from the corrugated drain hose. You

may need additional parts. See "Floor drain" under "Alternate

Parts."

1. Insert a new flat washer (supplied) into each end of the inlet

hoses. Firmly seat the washers in the couplings.

A B

A. Coupling

B. Washer

Connect the inlet hoses to the water faucets

Make sure the washer basket is empty.

2. Attach the hose with the red coupling to the hot water faucet.

Screw on coupling by hand until it is seated on the washer.

3. Attach the hose with the blue coupling to the cold water

faucet. Screw on coupling by hand until it is seated on the

washer.

4. Using pliers, tighten the couplings with an additional two-

thirds turn.

NOTE: Do not overtighten. Damage to the valves can result.

Clear the water lines

5. Run water through both faucets and inlet hoses, into a bucket

or laundry tub, to get rid of particles in the water lines that

might clog the inlet valve screens.

Connect the inlet hoses to the washer

6. Attach the hose with the blue coupling to the cold water (top)

inlet valve. Screw on coupling by hand until it is seated on the

washer. Using pliers, tighten the couplings with an additional

two-thirds turn.

NOTE: Do not overtighten. Damage to the valves can result.

A. Cold water inlet valve (blue)

B. Hot water inlet valve (red)

7. Attach the hose with the red coupling to the hot water

(bottom) inlet valve. Screw on coupling by hand until it is

seated on the washer. Using pliers, tighten the couplings with

an additional two-thirds turn.

NOTE: Do not overtighten. Damage to the valves can result.

If you are working in a closet or recessed area

Move the washer/dryer into its final position and remove

cardboard from under washer/dryer. Remove the access panel by

removing three Phillips-head screws and one bumper, located at

the top of the access panel. Set panel, screw, and bumper aside.

Complete hookup of water hoses and (on gas models) the flexible

gas connector through the access area. Replace access panel

upon completion of washer/dryer installation.

Check for leaks

8. Turn on the water faucets and check for leaks. A small amount

of water might enter the washer. You will drain this later.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Record hose installation or replacement dates for

future reference.

• If you connect only one water hose, you must cap off the

remaining water inlet port.

• Periodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.

Se,i:H,JH? ![)l)i]::i[k_!HO%!iii!_¸

1. Move the washer/dryer to its final location and remove any

cardboard used to move the washer/dryer.

2. Locate the plastic strap included in the parts package.

qZ>

Beaded tie strap

3. Wrap the drain hose to the laundry tub leg or standpipe with

the plastic strap (A or B below) and secure.

If the water faucets and the drain standpipe are recessed, put

the hooked end of the drain hose in the standpipe. Tightly

wrap the plastic strap around the water inlet hoses and the

drain hose (C above).

I::!:I!G ,,:ii1iii i_i

Typical exhaust installations

Typical installations vent the dryer from rear of the washer/dryer.

Other installations are possible.

Optional exhaust installations

This washer/dryer can be converted to exhaust out the right or left

side. To convert the washer/dryer, use Side Exhaust Kit

Part Number 279823. If your washer/dryer was previously

exhausted from the right or left side, it can be converted to rear

exhaust by using standard offset connections. To cover the hole in

the side, one of the following plugs can be added:

692790 (white)

3977784 (biscuit)

Follow the instructions in the kit to install. Kits are available from

the dealer from whom you purchased your washer/dryer.

T¸

J i

B C

A. Standard rear offset exhaust installation

B. Rear exhaust for offset close clearance connection

C. Left or right side exhaust installation

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for

your installation. Three close-clearance installations are shown.

Refer to the manufacturer's instructions provided with the vent

system.

, i ; ...........E

A. Dryer E. Elbow

B. Rigid metal or F. Clamps

flexible metal vent G. Elbow

C. Clamps H. Exhaust hood

D. Wall

J[ ....... ,

......

"\i .........

j[ ...... ,

t ......

"\ !

",,j .................. ",,,j.................

A B C

A. Loop system with standard elbows

B. Loop system with one offset & one standard elbow

C. Vent system with one periscope (2" [5 cm] clearance)

NOTE: The following kits for close clearance alternate installations

are available for purchase. For ordering information, please refer

to your Use and Care Guide.

• Over thetop Installation:

Part Number 4396028

Periscope Installation (For use with dryer vent to wall vent

mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch

Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm)

mismatch

Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm)

mismatch

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate

beneath the mobile home. Terminate the exhaust vent outside.

Determine vent length

1. Select the route that will provide the straightest and most

direct path outdoors. Plan the installation to use the fewest

number of elbows and turns. When using elbows or making

turns, allow as much room as possible. Bend vent gradually to

avoid kinking. Avoid 90° turns when possible.

2. Determine vent length.

The maximum length of the exhaust system depends upon:

• The type of vent (rigid metal or flexible metal).

• The number of elbows used.

• Type of hood.

Recommended hood styles are shown here.

(10.2cm)

A.Louvered hood style

B.Box hood style

The angled hood style (shown following) is acceptable.

See the exhaust vent length chart that matches your hood

type for the maximum vent lengths you can use.

Exhaust systems longer than those specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and

increased energy usage.

3. Determine the number of elbows you will need.

IMPORTANT: Do not use vent runs longer than those

specified in the Vent Length Chart.

The following chart helps you determine your maximum vent

length based on the number of 90° turns or elbows you will

need and the type of vent (rigid metal or flexible metal) and

hood that you will use.

Vent Length Chart

Number of Type of Vent Box or Angled

90° turns Louvered hoods

or elbows hoods

0 Rigid metal 43 ft (13.1 m) 36 ft (11.0 m)

Flexible metal 30 ft (9.1 m) 24 ft (7.3 m)

1 Rigid metal 33 ft (10.1 m) 26 ft (7.9 m)

Flexible metal 24 ft (7.3 m) 18 ft (5.5 m)

2 Rigid metal 24 ft (7.3 m) 16 ft (4.9 m)

Flexible metal 16 ft (4.9 m) 10 ft (3.0 m)

NOTE: Side exhaust adds a 90° turn inside the washer/dryer. To

determine maximum exhaust length, add one 90° turn to the

chart.

1. Install exhaust hood. Use caulking compound to seal exterior

wall opening around exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust

hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

3. Run vent to dryer location. Use the straightest path possible.

See "Determine vent length." Avoid 90° turns. Use clamps to

seal all joints. Do not use duct tape, screws or other fastening

devices that extend into the interior of the vent to secure vent.

iL@v,iii?[iiWCi_!;I;i!'_@L,i¸'!iiiiiii:_i_!i¸'_!!)_'@[

Properly leveling your washer/dryer prevents excessive noise and

vibration.

1. Check the levelness of the washer/dryer by placing a level on

the top edge of the washer, first side to side, then front to

back.

If the washer/dryer is not level, prop up the front with a wood

block and adjust the feet up or down as necessary. Remove

wood block and lower washer/dryer. Repeat this step until the

washer/dryer is level.

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in

washer/dryer. If connecting to existing vent, make sure the

vent is clean. The vent must fit over the exhaust outlet and

inside the exhaust hood. Make sure the vent is secured to

exhaust hood with a 4" (10.2 cm) clamp.

2. Move washer/dryer into final position. Do not crush or kink

vent. Make sure washer/dryer is level.

3. (On gas models) Check to be sure there are no kinks in the

flexible gas line.

1(1111iilii i! I!!_i,:11i!:1;ii::1i

1. Check to be sure all parts are now installed. If there is an extra

part, go back through the steps to see which step was

skipped.

2. Check to be sure you have all of your tools.

3. Dispose of/recycle all packaging materials. Keep the plastic

foam for use if the washer/dryer should be transported.

4. Check the washer/dryer's final location. Be sure the vent is not

crushed or kinked.

5. Check to be sure the washer/dryer is level and front leveling

feet are tight. See "Level Washer/Dryer."

6. Plug into a grounded outlet. Turn on power.

7. Check to be sure the water faucets are on.

8. Check for leaks around faucets and inlet hoses.

9. Remove the blue protective film on the console and any tape

remaining on the washer/dryer.

10. Read your Use and Care Guide.

11. Wipe the dryer drum interior thoroughly with a damp cloth to

remove any dust.

12. To test the washer, measure 1/2the normal recommended

amount of detergent and pour it into the washer. Close the lid.

Select the REGULAR cycle and pull out the Cycle Control

knob. Allow the washer to complete one whole cycle.

13. To test the dryer, set the dryer on a full heat cycle (not an air

cycle) for 20 minutes and start the dryer.

If the dryer will not start, check the following:

• Controls are set in a running or "On" position.

• Start button has been firmly pushed.

• Washer/dryer is plugged into a grounded outlet.

• Electrical supply is connected.

• House fuse is intact and tight, or circuit breaker has not

tripped.

• Dryer door is closed.

14. When the dryer has been running for 5 minutes, open the

dryer door and feel for heat.

If you do not feel heat, turn off the dryer and check the

following:

• There may be 2 fuses or circuit breakers for the dryer.

Check to make sure both fuses are intact and tight, or that

both circuit breakers have not tripped. If there is still no

heat, contact a qualified technician.

NOTE: You may notice a burning odor when dryer is first heated.

This odor is common when the heating element is first used. The

odor will go away.

8557471A

©) 2004.

10/04

Printed in U.S.A.

GE WSM2420D0CC Installation guide

Brand: GE

Model: WSM2420D0CC

Category: Washer dryers

Type: Installation guide

This manual is also suitable for

Download PDF

report

GE WSM2420D0CC Installation guide

This manual is also suitable for

GE WSM2420D0CC Installation guide

Related papers

Other documents