Sennheiser ADN-Software „Conference Manager“ User manual

System instruction manual

Audio

Distribution

Network

ADN Digital Conference System |1

Contents

Important safety instructions .................................................................................... 4

The Sennheiser ADN conference system .................................................................. 7

Available system components –

package contents ......................................................................................................... 8

Overview of the components ................................................................................... 10

ADN D1 delegate unit .................................................................................................. 12

ADN C1 chairperson unit ............................................................................................. 13

ADN-W D1 wireless delegate unit ............................................................................. 14

ADN-W C1 wireless chairperson unit ........................................................................ 15

ADN-W BA Lithium-Ion battery pack ....................................................................... 16

ADN-W MIC 15/ADN-W MIC 36 gooseneck microphones for wireless conference

units ................................................................................................................................ 17

ADN-W AM antenna module ...................................................................................... 18

NT 12-50C power supply ............................................................................................. 19

ADN CU1 central unit ................................................................................................... 20

“Conference Manager” software ............................................................................... 22

ADN PS power supply .................................................................................................. 23

SDC CBL RJ-45 system cables ..................................................................................... 24

ADN-W L 10 charger .................................................................................................... 24

ADN-W CASE transport and charging case .............................................................. 26

Structuring and controlling the conference system ............................................. 28

Number of chairperson and delegate units ............................................................ 28

Calculating the voltage supply of the wired conference units and system compo-

nents ............................................................................................................................... 28

Setting up a wired conference system ..................................................................... 29

Setting up a wireless conference system ................................................................ 32

Combining wired and wireless conference units (hybrid operation) ................. 33

Configuring and controlling the conference system ............................................. 34

Input and output of audio signals ............................................................................ 34

Integration into a media control system ................................................................. 34

Using the ADN Cable Calculator software ............................................................... 35

System requirements .................................................................................................. 35

Installing the ADN Cable Calculator .......................................................................... 35

Using the ADN Cable Calculator ................................................................................. 37

Uninstalling the ADN Cable Calculator ..................................................................... 37

Putting the conference system into operation ...................................................... 38

Preparing the ADN CU1 central unit for operation ................................................ 38

Preparing the ADN PS power supply for operation ............................................... 40

Preparing the ADN-W AM antenna module for operation ................................... 42

Preparing the ADN C1/ADN D1 wired conference units for operation .............. 44

Preparing the ADN-W C1/D1 wireless conference units for operation .............. 46

Preparing the ADN-W L 10 charger for operation ................................................. 48

Preparing the ADN-W CASE UNITS charging case for operation ......................... 49

Charging the ADN-W BA battery pack ..................................................................... 51

Setting up the conference system ............................................................................ 56

Connecting the ADN-W AM antenna module to the ADN CU1 central unit ...... 66

Setting up and positioning the antenna module ................................................... 69

Contents

2|ADN Digital Conference System

Setting up the ADN-W C1 or ADN-W D1 wireless conference units ................... 74

Connecting external audio devices to the central unit ......................................... 75

Connecting a USB mass storage device for audio recordings to the central unit ..

75

Preparing to use the “Conference Manager” software ......................................... 76

Switching the conference system on/off ................................................................. 77

Using the media control system ................................................................................ 80

Configuring the wireless components .................................................................... 81

Using the central unit ............................................................................................... 83

Deactivating the lock mode of the central unit ...................................................... 83

Functions of the keys ................................................................................................... 83

Configuring the conference system via the central unit ..................................... 84

Overview of the operating menu ............................................................................... 84

Working with the operating menu ........................................................................... 88

Adjusting the conference settings – “Conference Menu” .................................... 90

Ad

ju

sting the radio settings – “Wireless Menu“ ................................................... 95

Adjusting the

audio settings – “Audio Menu” ....................................................... 97

Check

ing the system and detecting errors –

“System Menu” .......................................................................................................... 102

Adjusting the language – “*Language” ............................................................... 113

Ad

justing further settings – “Settings” ............................................................... 113

Running a co

nference ............................................................................................. 115

Operating a delegate unit ........................................................................................ 116

Operating a chairperson unit .................................................................................. 118

Setting the volume of the conference units’ built-in loudspeakers ................ 120

Adding conference units to the conference system during operation ........... 121

Recording a conference ............................................................................................ 122

Using the “Conference Manager” software ......................................................... 125

Possibilities of usage of the software and the conference system ................. 125

Preparing the central unit’s integrated software for use .................................. 126

Preparing the Windows version of the software for use ................................... 127

Starting/exiting the software ................................................................................. 143

Getting to know and adjusting the basic features of the software ................ 144

Using the conference system and the software .................................................. 154

Configuring the settings for wireless conferencing ............................................ 160

Preparing a conference and mapping a conference room – “Setup” operating

mode ............................................................................................................................ 172

Initializing the conference units – “Setup” operating mode ............................ 189

Adjusting the conference settings – “Setup” operating mode ........................ 195

Controlling and monitoring a conference – “Live” operating mode ............... 203

Adding conference units to the conference system during operation ........... 213

Adjusting settings during a running conference ................................................ 214

Exiting “Live” operating mode ............................................................................... 216

Recording a conference – “Conference Recording” ............................................ 217

Using the log and diagnosis function – “Event Log” .......................................... 219

Cleaning and maintaining the conference system ............................................. 225

Transporting the wireless components ................................................................ 227

Preparing the wireless components for transport .............................................. 227

Using the ADN-W CASE transport and charging case ........................................ 227

ADN Digital Conference System |3

Contents

Updating the firmware of the conference system .............................................. 230

If a problem occurs .../Frequently asked questions ............................................ 231

Components and accessories .................................................................................. 237

Specifications ............................................................................................................ 240

Appendix ................................................................................................................... 248

Mounting dimensions ................................................................................................ 248

RF channels and transmission powers for wireless conferencing .................... 251

Factory default settings ............................................................................................ 253

Keyboard layouts ....................................................................................................... 254

Microsoft Software License Terms .......................................................................... 254

Manufacturer Declarations ..................................................................................... 257

Index – ADN conference system ............................................................................ 259

Index – “Conference Manager” software ............................................................. 263

Important safety instructions

4|ADN Digital Conference System

Important safety instructions

1. Read this system manual.

2. Keep this system manual. Always include the system manual when passing the

apparatus on to third parties.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use the apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufac-

turer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided plug does not fit into

your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly at plugs,

convenience receptacles, and the point where it exits from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manu-

facturer, or sold with the apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug the apparatus during lightning storms or when unused for long periods

of time.

14. Refer all servicing to qualified service personnel.

15. Servicing is required when the apparatus has been damaged in any way, such

as power supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, when the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

16. To completely disconnect the apparatus from the AC mains, disconnect the

power supply cord plug from the AC receptacle.

17. WARNING: To reduce the risk of fire or electric shock, do not expose the appara-

tus to rain or moisture.

18. Do not expose the apparatus to dripping or splashing and ensure that no

objects filled with liquids, such as vases, are placed on the apparatus.

19. The mains plug of the power supply cord shall remain readily accessible.

ADN Digital Conference System |5

Important safety instructions

Hazard warnings on the rear of products with mains plug

The label shown on the left is attached to the rear

of products with mains plug

(ADN CU1 central unit, ADN PS power supplies, ADN-W L10 chargers and ADN-W

CASE UNITS). The symbols on this label have the following meaning:

Presence of uninsulated dangerous voltage within the product’s enclosure

(ADN CU1 central unit, ADN PS power supplies, ADN-W L10 chargers and ADN-W

CASE UNITS) that may be of sufficient magnitude to constitute risk of electric

shock.

Never open the ADN CU1 central unit, the ADN PS power supplies, the ADN-W L10

chargers and the ADN-W CASE UNITS as there is a risk of electric shock. There are

no user serviceable parts inside. Refer servicing to an authorized Sennheiser ser-

vice partner.

Read and follow the safety and operating instructions contained in the instruction

manual.

Risk of fire due to overloading

Do not overload wall outlets an

d extension cabl

es as this may result in fire and elec-

tric shock.

Danger of hearing damage due to high volumes

These products are used for commercial purposes. Commercial use is subject to the

rules and regulations of the trade association responsible. Sennheiser, as the man-

ufacturer, is therefore obliged to expressly point out possible health risks arising

from use.

When the conference participants listen to the floor channel via headphones, they

can adjust the volume themselves. In doing so, sound pressure exceeding 85 dB(A)

can be produced. 85 dB(A) is the sound pressure corresponding to the maximum

permissible volume which is by law (in some countries) allowed to affect your hear-

ing for the duration of a working day. It is used as a basis according to the specifi-

cations of industrial medicine. Higher volumes or longer durations can damage

your hearing. At higher volumes, the duration must be shortened in order to pre-

vent hearing damage. The following are sure signs that you have been subjected

to excessive noise for too long a time:

• You can hear ringing or whistling sounds in your ears.

• You have the impression (even for a short time only) that you can no longer

hear high notes.

Inform the conference participants about these facts and, if necessary, ask them to

set the volume to a medium level.

Warning on the use of the wireless components

In some countries/regions and for certain ra

di

o channels, the use of wireless com-

ponents is subject to special legal requirements. Only use the wireless components

in accordance with these legal requirements in order to avoid interference to other

radio equipment. Make sure to always set the correct country/region (via the oper-

ating menu of the ADN CU1 central unit) in which the wireless components are to

be used. This ensures that the conference system uses only the radio settings

(radio frequencies and transmission powers) that are approved and legal in the

respective country.

In some countries/regions (e.g. Canada), the use of wireless components operating

in the 5.15 to 5.25 GHz frequency band is restricted to indoor use.

Important safety instructions

6|ADN Digital Conference System

Safety instructions for the Lithium-Ion battery pack

If abused or misused, the ADN-W BA battery pack may leak. In extrem

e cases, it

may even present:

Please understand that Sennheiser does not accept liability for damage arising

from abuse or misuse.

Intended use

Intended use of the products in

cludes:

• using the products for professional purposes,

• having read and understood this system manual and especially the chapter

“Important safety instructions” on page 4,

• using the products within the operating conditions and limitations described in

this system manual.

“Improper use” means using the products other than as described in this system

manual, or under operating conditions which differ from those described therein.

All instruction manuals for components of the ADN conference system are also

available on the Internet at www.sennheiser.com.

• a heat hazard,

•a fire hazard,

• an explosion hazard,

• a smoke or gas hazard.

Keep away from children. Do not pack charged battery

packs loose.

Observe correct polarity. Do not short-circuit.

Do not expose to moisture. Do not mutilate or dismantle.

Only charge the battery pack

with the appropriate

Sennheiser chargers.

When not using the battery

pack for extended periods

of time, charge it regularly

(charge it to approx. 50%

of capacity about every

3 months).

Only charge the battery pack

at ambient temperatures

between 10°C/50°F and

45°C/113°F.

Do not heat above 45°C/113°F,

e.g. do not expose to sunlight

or throw into a fire.

Immediately remove the

battery pack from an obviously

defective device.

Do not continue to use a

defective battery pack.

Switch battery pack-powered

devices off after use.

When not using the device

for extended periods of time,

remove the battery pack from

the device.

Only use the original

Sennheiser battery packs.

Dispose of the battery pack

at special collection points

or return it to your specialist

dealer.

www.sennheiser.com

www

Manual

ADN Digital Conference System |7

The Sennheiser ADN conference system

Sennheiser ADN stands for Sennheiser Audio Distribution Network – the new gen-

eration of digital conference equipment. The ADN conference system has been

designed for maximum versatility and can be easily adapted to many different

requirements.

The conference system offers the following features:

• State-of-the-art conference technology for up to 400 participants

• Optimum speech intelligibility due to quality microphone and dual

loudspeakers in each conference unit

• Attractive design – fits into modern or traditional style conference rooms

• High operational reliability due to state-of-the-art transmission technology

• Wired conference units and mobile wireless conference units enable quick and

easy adaptation to different room sizes and participant numbers

• Fail-safe audio transmission due to redundant cabling or due to dynamic

frequency management in a wireless conference system

• Intuitive configuration and control of the conference system via “Conference

Manager” software or operating menu

• Audio recording of conferences on a USB mass storage device

The wireless components offer the following features:

• Dynamic frequency management for interference-free operation

• Can be used all over the world due to up to 28 license-free frequencies

• Secure data transmission with 128-bit-AES encryption

• Ease of use due to automatic configuration of the system

• Wireless conference units with up to 20 hrs operating time

• Easy expansion of the conference system and hybrid operation between wired

and wireless conference units

Available system components – package contents

8|ADN Digital Conference System

Available system components –

package contents

ADN wired standard components

ADN CU1 central unit 1 ADN CU1 central unit

1 mains cable (with EU, UK or US mains plug, depending on version), length 1.8 m

1 instruction manual

1 “Safety information” supplement

1 DVD-ROM (including, among other things, the “Conference Manager” software,

the “ADN Cable Calculator” software and the instruction manual for the overall

conference system as PDF)

ADN PS power supply 1 ADN PS power supply with premounted rack mount “ears”

1

mains cable (with EU, UK or US mains plug, depending on version), length 1.8 m

1 instruction manual

1 “Safety information” supplement

ADN D1 delegate unit 1 ADN D1 delegate unit

1

instruction manual

ADN C1 chairman unit 1 ADN C1 chairperson unit

1 instruction manual

System cable SDC CBL RJ45, available in different lengths (2 m to 50 m, see “Components and

accessori

es” on page 237)

ADN wireless components

ADN-W AM antenna module 1 ADN-W AM antenna module with 3 rod antennas

(ADN-W AM or ADN-W AM-US version)

1 SDC CBL RJ45-5 system cable, length 5 m

1 thread insert (5/8" to 3/8")

1 instruction manual

Console of the ADN-W D1

wireles

s

delegate unit

1 console of the ADN-W D1 wireless delegate unit

(without battery pack and gooseneck microphone)

1 instruct

ion manual

Console of the ADN-W C1

wirel

ess chairperson unit

1 console of the ADN-W C1 wireless chairperson unit

(without battery pack and gooseneck microphone)

1 instruction manual

ADN-W BA battery pack for

wirele

ss conference units

1 ADN-W BA Lithium-Ion battery pack

1 instruction manual

Gooseneck microphones for

wireless conference units

1 ADN-W MIC 15-39 (length 39 cm, KE 10 microphone capsule) or

ADN-W MIC 36-29 (length 29 cm, ME 36 microphone capsule) or

ADN-W MIC 15-50 (length 50 cm, KE 10 microphone capsule) or

ADN-W MIC 36-50 (length 50 cm, ME 36 microphone capsule)

1 instruction manual

Wireless conference unit kit for

d

e

legate unit

1 console of the ADN-W D1 wireless delegate unit

1 ADN-W BA battery pack

1 gooseneck microphone (ADN-W MIC 15-39 or 36-29, depending on version)

3 instruction manuals (one for the wireless conference unit, one for the battery

pack and one for the gooseneck microphone)

ADN Digital Conference System |9

Available system components – package contents

NT 12-50C power supply Power supply for charging one ADN-W BA or for optionally powering the ADN-W

AM antenna module

1 NT 12-50C power supply

1 mains cable (with EU, UK or US mains plug, depending on version), length 2.5 m

1 instruction manual

ADN-W L 10 charger

for

charging up to

10 ADN-W BA battery packs

1 ADN-W L 10 charger

1 mains cable (with EU, UK or US mains plug, depending on version), length 1.8 m

1 instruction manual

1 “Safety information” supplement

Transport components

The following transport components are available:

• ADN-W CASE BASE case bottom with wheels and case lid

• ADN-W CASE CENTRAL transport case for e.g. central unit, antenna module and

accessories

• ADN-W CASE UNITS charging case with charging compartments for 10 wireless

conference units

ADN-W CASE UNITS

chargi

ng ca

se

1 ADN-W CASE UNITS charging case with charging compartments for 10 wireless

conference units

1 mains cable (with EU, UK or US mains plug, depending on version), length 1.8 m

(also available without mains cable)

1 instruction manual

1 “Safety information” supplement

ADN-W CASE CENTRAL

transport

ca

se

1 ADN-W CASE CENTRAL transport case for e.g. central unit, antenna module and

accessories

ADN-W CASE BASE

case b

ottom and lid

1 ADN-W CASE BASE including

– case bottom with wheels

–case lid

ADN-W CASE KIT 20

tran

sport an

d charging case kit for

20 wireless conference units

1 ADN-W CASE BASE case bottom with wheels and case lid

2 ADN-W CASE UNITS charging cases, each with charging compartments for

10 wireless conference units

2 mains cables (with EU, UK or US mains plug, depending on version),

length 1.8 m

(also available without mains cables)

1 instruction manual

1 “Safety information” supplement

The modules can be used separately or be combined arbitrarily (see page 227).

Overview of the components

10 | ADN Digital Conference System

Overview of the components

Components required for setting up a wired conference system:

• 1 ADN CU1 central unit

• ADN D1 delegate units (a maximum of 400 delegate units can be used in a

conference system)

• ADN C1 chairperson units (optional, for granting speaking privileges, a

maximum of 10 chairperson units can be used in a conference system)

• SDC CBL RJ-45 system cables (available in different lengths)

• ADN PS power supplies (optional, for conferences with up to 400 conference

units connected in simple strings or in redundant ring topology; a maximum of

15 ADN PS can be used in a conference system – for the exact calculation, use

the ADN Cable Calculator software)

• “Conference Manager” software for configuring and controlling conferences

(optional)

– can be run on the central unit (a screen, keyboard, and mouse are required)

or

– can be run on a separate Windows PC with Ethernet connection

ADN PS ADN PS

“Conference Manager”

software

ADN CU1

max. 40

ADN D1/ADN C1

max. 15 ADN PS

max. 400

ADN D1/ADN C1

per ADN PS with standard

cabling a max. of 70

ADN D1/ADN C1

per ADN PS with redundant

ring cabling a max. of 40

ADN D1/ADN C1

Conferences with up to a

max. of 40 participants

Conferences with up to a max. of 400 participants

ADN Digital Conference System |11

Overview of the components

Components required for setting up a wireless conference system:

• 1 ADN CU1 central unit

• at least 1 ADN-W AM antenna module for operating the wireless conference

units

• ADN-W D1 wireless delegate units (a maximum of 150 delegate units can be

used in a conference system)

• ADN-W C1 wireless chairperson units (optional, for granting speaking privi-

leges, a maximum of 10 chairperson units can be used in a conference system)

• “Conference Manager” software for configuring and controlling conferences

(optional)

– can be run on the central unit (a screen, keyboard, and mouse are required)

or

– can be run on a separate Windows PC with Ethernet connection

Component required for audio recording of conferences (optional):

•U

S

B mass storage device (e.g. external hard disk)

ADN C1 and ADN D1 wired conference units and ADN-W C1 and ADN-W D1

wireless conference units can be combined arbitrarily as long as you ensure

correct set-up and cabling and comply with the specifications (a conference

system can comprise a total of 400 conference units of which up to 150 can

be wireless, see page 56).

ADN CU1

max. 150 conference units per CU1

max. 75 conference units per antenna module

75

...

max. 50 m

ADN CU1 ADN-W AM

> 1 m

> 0,5 m

ADN-W AM

3214

PORT II

PORT I

“Conference Manager“

software

ADN CU1

HDD

• REC

Overview of the components

12 | ADN Digital Conference System

ADN D1 delegate unit

Sound inlet basket with glued

windshield

Signal light ring

Headphone socket

Headphone volume control for

headphone socket

Microphone key

Microphone LED

Loudspeaker

IN socket

OUT socket

Type plate

(see bottom)

:

2

1

A

B

3

6

7

8

9

1

2

3

6

7

8

9

<

A

B

ADN Digital Conference System |13

Overview of the components

ADN C1 chairperson unit

Sound inlet basket with glued

windshield

Signal light ring

Headphone socket

Priority key

Next key

Headphone volume control for

headphone socket

Microphone key

Microphone LED

Loudspeaker

IN socket

OUT socket

Type

plate (see bottom)

:

2

1

A

3

6

5

4

7

8

9

B

1

2

3

4

5

6

7

8

9

<

A

B

Overview of the components

14 | ADN Digital Conference System

ADN-W D1 wireless delegate unit

D

C

9

8

7

6

3

ADN-W MIC 15-50

ADN-W MIC 15-39

ADN-W MIC 36-29

ADN-W MIC 36-50

E

B

A

<

A

<

1

2

1

2

A

<

A

<

1

2

1

2

Sound inlet basket with glued

windshield

Signal light ring

Headphone socket

Headphone volume control for

headphone socket

Microphone key

Microphone LED

Loudspeaker

Fastening thread

Sliding contacts

Microphone connection

Guide rails for ADN-W BA

battery pack

Connection for ADN-W BA

battery pack

Type plate

1

2

3

6

7

8

9

<

A

B

C

D

E

ADN Digital Conference System |15

Overview of the components

ADN-W C1 wireless chairperson unit

9

8

7

6

5

4

3

B

D

C

ADN-W MIC 15-50

ADN-W MIC 15-39

ADN-W MIC 36-29

ADN-W MIC 36-50

E

A

<

A

<

1

2

1

2

A

<

A

<

1

2

1

2

Sound inlet basket with glued

windshield

Signal light ring

Headphone socket

Priority key

Next key

Headphone volume control for

headphone socket

Microphone key

Microphone LED

Loudspeaker

Fastening thread

Sliding contacts

Microphone connection

Guide rails for ADN-W BA

battery pack

Connection for ADN-W BA

battery pack

Type plate

1

2

3

4

5

6

7

8

9

<

A

B

C

D

E

Overview of the components

16 | ADN Digital Conference System

ADN-W BA Lithium-Ion battery pack

Over view of the status LEDs

The charge status display consists of 5 LEDs a

nd can be called up by pressing the

button . During charging, the LEDs show the obtained capacity.

Battery status indicator

RF status indicator

Charging contacts for

ADN-W CASE UNITS charging case

Hollow jack socket for connection of

NT 12-50C power supply

Button for charge status indication

Charge status indicator

Contacts for connection to

wireless conference unit and

ADN-W L 10 charger

Battery release clip

Type plate

1

2

3

4

8

7

5

6

9

5

Rechargeable Lithium-Ion Battery Pack

Art.No.: 504744 Ser.-No.:

MADE IN POLAND

Rated Voltage/Capacity/Energy: 7.4V/7.8Ah/57.72Wh

Charge Voltage/Current: 12V/2.5A

2ICR19/65-3

ADN-W BA

LI-ION

LISTED

CUS

1

2

3

4

5

6

7

8

9

1

2

Status-LED Color Meaning

Battery status

indicator

– Battery capacity 5-100%

orange, flashing slowly Battery capacity < 5%,

battery pack is almost flat

orange, flashing rapidly Battery pack is defective

orange, lit permanently Battery pack is being charged

RF status

indicator

– Good transmission quality

blue, flashing slowly Transmission quality is tempo-

rarily reduced

blue, flashing rapidly Transmission quality is perma-

nently reduced

1

2

12345

5

6

LED

Color Remaining capacity Remaining operating time

1 red approx. 0-19% approx. 0-4 hours

2 orange approx. 20-39% approx. 4-8 hours

3 orange approx. 40-59% approx. 8-12 hours

4 green approx. 60-79% approx. 12-16 hours

5 green approx. 80-100% approx. 16-20 hours

6

5

6

ADN Digital Conference System |17

Overview of the components

ADN-W MIC 15/ADN-W MIC 36 gooseneck microphones

for wireless conference units

Sound inlet basket with glued

windshield

Signal light ring

Fastening thread

Sliding contacts for connection to

the console of a wireless conference

unit

4

3

1

2

1

2

1

2

1

2

ADN-W MIC 15-50 = 50 cm

ADN-W MIC 15-39 = 39 cm

ADN-W MIC 36-50 = 50 cm

ADN-W MIC 36-29 = 29 cm

1

2

3

4

Overview of the components

18 | ADN Digital Conference System

ADN-W AM antenna module

7

6

95 mm

543

9

8

12

8

1 A

::

Hole for safety wire

Cable grip

Output socket

Input socket

Hollow jack socket for connection of

optional NT 12-50C power supply

Antennas

Antenna coupling ring

Mounting holes for wall mounting

5/8" mounting thread

with 3/8" thread insert

Rubber feet

Type plate

1

2

3

4

5

6

7

8

9

>

A

ADN Digital Conference System |19

Overview of the components

NT 12-50C power supply

The power supply can charge one ADN-W BA battery pack or can optionally power

the ADN-W AM antenna module.

Mains cable with mains plug

(with EU, UK or US mains plug,

depending on version)

Hollow jack plug

Euro 8 socket for mains cable

NT 12-50C

EU

UK

US

2

3

1

2

3

Page is loading ...

Sennheiser ADN-Software „Conference Manager“ User manual

This manual is also suitable for

Sennheiser ADN-Software „Conference Manager“ User manual

Related papers

Other documents