CyberData 011388 Owner's manual

Brand: CyberData

Model: 011388

Type: Owner's manual

Getting Started

Take the following into consideration before you install this product:

• When this secure phone case is used, the touch screen capability of the DX phone is disabled.

• Due to the size and mass of this product, it is important that the Backbox is safely installed according to these installation

instructions.

• Make sure that the type of wall is capable of supporting the system and use screws that are suitable for that type of wall.

• The system must be installed by qualified personnel in accordance with state and local building regulations.

• Also see the Install the DX70 Phone to Enclosure (on the other page).

• Locate the provided Security Torx Driver Bit (usually taped right next to the Hookswitch on the Faceplate).

• Tool required to remove Security Torx Screws (an Electric Hand Drill or Powered Screwdriver)

• WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation

instructions.

• WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.

• WARNING: This enclosure is not rated for any AC voltages!

Hookswitch Wires to USB to Analog Audio Module Connections

Contacting CyberData

Black Wire

to Terminal

Black Wires

USB-B

Black Wire to Terminal

Green Wire to Terminal

Yellow Wire to Terminal

Red Wire to Termianl

Terminal

Audio Module

USB to Analog

Block

Armored Cord

Handset Retainer

Factory Disconnected

to Terminal 5

Red Wire

Connections

Reconnect Before Fasten Faceplate Assembly to Backbox

Connector

Receptacle

Connector

Plug

Magnetic Hookswitch

Backbox

***

Connections

Armored Cord Handset

USB-A

Phone

Cable Connections

USB-B to USB-A

Sales: 831-373-2601 ext. 334

Support: 831-373-2601 ext. 333

Support Website: http://support.cyberdata.net/

RMA Department: 831-373-2601 ext. 136

RMA Email: [email protected]

RMA Status: http://support.cyberdata.net/

Warranty Information: http://support.cyberdata.net/

Corporate Headquarters

CyberData Corporation

3 Justin Court

Monterey, CA 93940, USA

Phone: 831-373-2601

Fax: 831-373-4193

http://www.cyberdata.net/

Backbox Mounting

Install a Shunt on JP2 to Enable Auto Answer Mode

Dimensions are in Inches [Millimeter]

Conduit Hole Ø 1.3 [Ø33] Fits 1" EMT Fittings

Ø1.3 [Ø33]

Conduit Hole

1.969 [50.0]

4.026 [102.3]

6.212 [157.8]

1.969 [50.0]

2.362 [60.0]

14.173 [360.0]

17.717 [450.0]

2.165 [55.0]

19.685 [500.0]

13.386 [340.0]

6.496 [165.0]

Ø0.41 [Ø10.5]

Last Updated 08/06/2020

View Shown with Hole Plug Installed.

Open Faceplate then Remove Nut from the Inside.

11/32" or 9mm Socket & Socket Wrench

Tool Required to Remove Hole Plug:

JP2

Shunt

The IP Endpoint Company

Installation Quick Reference

DX70 Secure Phone

011388

Install the DX70 Phone to Enclosure

Use a Paper Clip Through Hole

HOOK

RECEIVER

1) Unsnap to Remove Both Plastic Pieces Above Connector Panel

Mic

Hole

2) Place Power Adapter in to Power Adapter Holder

2a) Insert Power & Ethernet Cables Through Any Desired Conduit

4) Place PINS onto Hook Receiver on Backbox

4a) At the Same Time, Place the Camera onto Foam Holder

2b) Connect Cables (Power, Ethernet, USB, etc.) to Connector Panel

Cover Hole with Provided

Torx Button Socket Cap Screw &

T15 Torx Driver Bit

3) Connect the USB - A to B Cable:

HOOK

RECEIVER

4b) Place Foot Stand onto Power Adapter Holder

USB-B to USB to Analog Audio Module (UAAM), USB-A to Phone

5) Connect Wires from Armored Cord Handset &

Hookswitch to Terminal Block on UAAM

BACKBOX

6a) Lift Foot Stand Upward with Left Hand,

6b) Grasp the Upper Right Corner of the Phone with Right Hand

Still Connected.

Camera

Foam Holder

Hole Plug

Faceplate

Remove Phone from Backbox Slowly Because Cables are

Cutout, Conduit Hole Ø 1.16 [Ø29.5] Fits 1" EMT Fittings

Speaker

Hole Cluster

11/32" or 9mm Socket & Socket Wrench

Tool Required to Remove Hole Plug:

Power Plug

DX70

(Customer Provided)

Open Camera Shutter

1) Use Clean Damp Cloth to Wipe Surface Clean

Screen Cleaning Instruction:

Place

Here

Power Supply

Power Cable

to AC Outlet

Phone Mounting Instruction:

Power Cord

Through Slot

Plexiglass Cleaning Instruction:

Plexiglass Cleaner to Wipe Surface Clean

Use Provided Security Torx

Driver Bit to Fasten Screws to Backbox

Tool Required:

Electric Hand Drill or

Powered Screwdriver

2) Screw Driver

1) Hammer

Tool Required to Remove Knock Outs (KO):

3) Plier

Self-Tapping Screw, Stud Anchors or

Fits up to 1/4" [10 mm] Square Neck Carriage Bolt,

Knock Outs (KO) & Keyholes:

Machine Screw

USB-B

Plug

Use Provided Security Torx

Driver Bit to Fasten Cover Screw

to Faceplate

Note #1

(See Note #1)

Power Adapter

Holder

USB-A

Plug

Power Adapter

(See Figure #3)

Figure #2 (See Also Figure #5)

Figure #3

(See Figure #4)

Figure #4

(See Figure #2)

Use Provided #00 Screw Driver

to Install Wires to Terminal Block

Turn Clockwise to

Remove Phone from Backbox:

Ethernet

Foot Stand

1) Use only lint Free Microber Tower &

Black Wire

to Terminal

Black Wires

USB-B

Black Wire to Terminal

Green Wire to Terminal

Yellow Wire to Terminal

Red Wire to Termianl

Terminal

Audio Module

USB to Analog

Block

Armored Cord

Handset Retainer

Factory Disconnected

to Terminal 5

Red Wire

Connections

Reconnect Before Fasten Faceplate Assembly to Backbox

Connector

Receptacle

Connector

Plug

Magnetic Hookswitch

Backbox

***

Connections

Armored Cord Handset

USB-A

Phone

Cable Connections

USB-B to USB-A

Audio Module

USB to Analog

CyberData 011388 Owner's manual

CyberData 011388 Owner's manual

CyberData 011388 Owner's manual

Related papers

Other documents