Lenovo ThinkPad T400s Hardware Maintenance Manual

ThinkPad T400s

Hard ware Maintenan ce Manual

ThinkPad T400s

Hard ware Maintenan ce Manual

Note

Before using this information and the product it supports, be sure to read the general information under “Notices” on page

187.

Second Edition (October 2009)

LENOVO products, data, computer software, and services have been developed exclusively at private expense and

are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted

rights to use, reproduction and disclosure.

LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered

pursuant a General Services Administration ″GSA″ contract, use, reproduction, or disclosure is subject to restrictions

set forth in Contract No. GS-35F-05925.

Contents

About this manual ..........v

Safety information ..........1

General safety ..............2

Electrical safety .............3

Safety inspection guide ...........5

Handling devices that are sensitive to electrostatic

discharge ...............6

Grounding requirements ..........6

Safety notices (multilingual translations) .....7

Laser compliance statement (multilingual

translations) ..............28

Important service information .....39

Strategy for replacing FRUs .........39

Strategy for replacing a hard disk drive ....40

Important notice for replacing a system board . . 40

How to use error message ........40

Strategy for replacing FRUs for CTO, CMV, and

GAV.................41

Product definition ...........41

FRU identification for CTO, CMV, and GAV

products ..............41

General checkout ..........43

What to do first .............44

Checkout guide .............45

Diagnostics using PC-Doctor for DOS ....45

Lenovo ThinkVantage Toolbox (Lenovo System

Toolbox) ..............48

PC-Doctor for Rescue and Recovery .....48

FRU tests ..............49

Power system checkout ..........51

Checking the AC adapter .........51

Checking operational charging .......52

Checking the battery pack ........52

Checking the backup battery .......53

Related service information......55

Restoring the factory contents by using Product

Recovery discs .............55

Restoring the factory contents by using Recovery

Disc Set ...............56

Passwords ...............57

Power-on password ..........57

Hard-disk password ..........57

Supervisor password ..........58

How to remove the power-on password ....58

How to remove the hard-disk password ....59

Power management ...........60

Screen blank mode ...........60

Sleep (Standby) mode ..........60

Hibernation mode ...........61

Symptom-to-FRU index ..........62

Numeric error codes ..........62

Error messages ............66

Beep symptoms ............67

No-beep symptoms...........67

LCD-related symptoms .........68

Intermittent problems ..........69

Undetermined problems .........69

Status indicators ..........71

Fn key combinations ........75

FRU replacement notices .......79

Screw notices ..............79

Retaining serial numbers ..........80

Restoring the serial number of the system unit 80

Retaining the UUID ..........80

Reading or writing the ECA information . . . 81

Removing and replacing a FRU ....83

Before servicing ThinkPad T400s .......84

1010 Battery pack ............85

1020 Serial Ultrabay Slim device or travel bezel . . 86

1030 Solid state drive (SSD) or hard disk drive

(HDD) ................87

1040 DIMM ..............89

1050 PCI Express Mini Card for wireless LAN. . . 91

1060 PCI Express Mini Card for wireless WAN . . 94

1070 Keyboard .............97

1080 Backup battery ...........102

1090 Wireless USB adapter or Intel Turbo Memory 103

1100 Palm rest or palm rest with fingerprint reader 105

1110 Bluetooth daughter card (BDC-2) .....107

1120 Keyboard bezel and speaker assembly . . . 108

1130 5-in-1 Media Card Reader adapter.....112

1140 Bluetooth–wireless radio switch FPC ....113

1150 LCD unit .............115

1160 System board, fan assembly, and 34-mm

ExpressCard slot frame ..........119

1170 I/O sub card and base cover assembly . . . 125

2010 LCD bezel assembly .........127

2020 LCD latch L and R ..........129

2030 Integrated camera or microphone sub card 130

2040 LED sub card ...........132

2050 LCD panel ............133

2060 LCD cable.............136

2070 Hinge kit .............137

2080 LED cable .............139

2090 Antenna kit and LCD rear cover assembly 141

Locations .............143

Front view ..............143

Rear view ..............144

Bottom view..............145

Parts list .............147

Overall ...............148

LCD FRUs ..............159

Keyboard...............167

Miscellaneous parts ...........168

AC adapters..............170

Power cords ..............171

Recovery discs .............172

Windows XP Professional (32 bit) DVDs . . . 172

Windows Vista Starter Edition (32 bit) DVDs 173

Windows Vista Home Basic (32 bit) DVDs. . . 174

Windows Vista Home Premium (32 bit) DVDs 175

Windows Vista Business (32 bit) DVDs ....176

Windows Vista Business (64 bit) DVDs ....178

Windows Vista Ultimate (32 bit) DVDs ....179

Windows 7 Home Basic (32 bit) DVDs ....180

Windows 7 Home Premium (32 bit) DVDs . . 181

Windows 7 Home Premium (64 bit) DVDs . . 182

Windows 7 Professional (32 bit) DVDs ....183

Windows 7 Professional (64 bit) DVDs ....185

Common service tools ..........186

Notices ..............187

Trademarks ..............188

iv ThinkPad T400s Hardware Maintenance Manual

About this manual

This manual contains service and reference information for the following

ThinkPad

®

products.

ThinkPad T400s

MT 2801, 2808, 2809, 2815, 2823, 2824, and 2825

Use this manual along with the advanced diagnostic tests to troubleshoot

problems.

Important:

This manual is intended only for trained service technicians who are familiar

with ThinkPad products. Use this manual along with the advanced diagnostic

tests to troubleshoot problems effectively.

Before servicing a ThinkPad product, be sure to read all the information under

“Safety information” on page 1 and “Important service information” on page 39.

vi ThinkPad T400s Hardware Maintenance Manual

Safety information

This chapter presents following safety information that you need to be familiar

with before you service a ThinkPad Notebook.

v “General safety” on page 2

v “Electrical safety” on page 3

v “Safety inspection guide” on page 5

v “Handling devices that are sensitive to electrostatic discharge” on page 6

v “Grounding requirements” on page 6

v “Safety notices (multilingual translations)” on page 7

v “Laser compliance statement (multilingual translations)” on page 28

General safety

Follow these rules to ensure general safety:

v Observe good housekeeping in the area of the machines during and after

maintenance.

v When lifting any heavy object:

1. Make sure that you can stand safely without slipping.

2. Distribute the weight of the object equally between your feet.

3. Use a slow lifting force. Never move suddenly or twist when you attempt to

lift.

4. Lift by standing or by pushing up with your leg muscles; this action removes

the strain from the muscles in your back. Do not attempt to lift any object that

weighs more than 16 kg (35 lb) or that you think is too heavy for you.

v Do not perform any action that causes hazards to the customer, or that makes

the equipment unsafe.

v Before you start the machine, make sure that other service technicians and the

customer’s personnel are not in a hazardous position.

v Place removed covers and other parts in a safe place, away from all personnel,

while you are servicing the machine.

v Keep your toolcase away from walk areas so that other people will not trip over

it.

v Do not wear loose clothing that can be trapped in the moving parts of a

machine. Make sure that your sleeves are fastened or rolled up above your

elbows. If your hair is long, fasten it.

v Insert the ends of your necktie or scarf inside clothing or fasten it with a

nonconductive clip, about 8 centimeters (3 inches) from the end.

v Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your

clothing.

Attention: Metal objects are good electrical conductors.

v Wear safety glasses when you are hammering, drilling, soldering, cutting wire,

attaching springs, using solvents, or working in any other conditions that might

be hazardous to your eyes.

v After service, reinstall all safety shields, guards, labels, and ground wires.

Replace any safety device that is worn or defective.

v Reinstall all covers correctly before returning the machine to the customer.

v Fan louvers on the machine help to prevent overheating of internal components.

Do not obstruct fan louvers or cover them with labels or stickers.

2 ThinkPad T400s Hardware Maintenance Manual

Electrical safety

Observe the following rules when working on electrical equipment.

v Find the room emergency power-off (EPO) switch, disconnecting switch, or

electrical outlet. If an electrical accident occurs, you can then operate the switch

or unplug the power cord quickly.

v Do not work alone under hazardous conditions or near equipment that has

hazardous voltages.

v Disconnect all power before:

– Performing a mechanical inspection

– Working near power supplies

– Removing or installing main units

v Before you start to work on the machine, unplug the power cord. If you cannot

unplug it, ask the customer to power-off the wall box that supplies power to the

machine, and to lock the wall box in the off position.

v If you need to work on a machine that has exposed electrical circuits, observe the

following precautions:

– Ensure that another person, familiar with the power-off controls, is near you.

Attention: Another person must be there to switch off the power, if

necessary.

– Use only one hand when working with powered-on electrical equipment;

keep the other hand in your pocket or behind your back.

Attention: An electrical shock can occur only when there is a complete

circuit. By observing the above rule, you may prevent a current from passing

through your body.

– When using testers, set the controls correctly and use the approved probe

leads and accessories for that tester.

– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you

from grounds such as metal floor strips and machine frames.

Observe the special safety precautions when you work with very high voltages;

Instructions for these precautions are in the safety sections of maintenance

information. Use extreme care when measuring high voltages.

v Regularly inspect and maintain your electrical hand tools for safe operational

condition.

v Do not use worn or broken tools and testers.

v Never assume that power has been disconnected from a circuit. First, check that it

has been powered off.

v Always look carefully for possible hazards in your work area. Examples of these

hazards are moist floors, nongrounded power extension cables, power surges,

and missing safety grounds.

Important:

Use only approved tools and test equipment. Some hand tools have handles

covered with a soft material that does not insulate you when working with live

electrical currents.

Many customers have, near their equipment, rubber floor mats that contain small

conductive fibers to decrease electrostatic discharges. Do not use this type of mat

to protect yourself from electrical shock.

Safety information 3

v Do not touch live electrical circuits with the reflective surface of a plastic dental

mirror. The surface is conductive; such touching can cause personal injury and

machine damage.

v Do not service the following parts with the power on when they are removed

from their normal operating places in a machine:

– Power supply units

– Pumps

– Blowers and fans

– Motor generators

– Similar units to listed above

This practice ensures correct grounding of the units.

v If an electrical accident occurs:

– Use caution; do not become a victim yourself.

– Switch off power.

– Send another person to get medical aid.

4 ThinkPad T400s Hardware Maintenance Manual

Safety inspection guide

The purpose of this inspection guide is to assist you in identifying potentially

unsafe conditions. As each machine was designed and built, required safety items

were installed to protect users and service technicians from injury. This guide

addresses only those items. You should use good judgment to identify potential

safety hazards due to attachment of non-ThinkPad features or options not covered

by this inspection guide.

If any unsafe conditions are present, you must determine how serious the apparent

hazard could be and whether you can continue without first correcting the

problem.

Consider these conditions and the safety hazards they present:

v Electrical hazards, especially primary power (primary voltage on the frame can

cause serious or fatal electrical shock)

v Explosive hazards, such as a damaged CRT face or a bulging capacitor

v Mechanical hazards, such as loose or missing hardware

To determine whether there are any potentially unsafe conditions, use the

following checklist at the beginning of every service task. Begin the checks with

the power off, and the power cord disconnected.

Checklist:

1. Check exterior covers for damage (loose, broken, or sharp edges).

2. Power off the computer. Disconnect the power cord.

3. Check the power cord for:

a. A third-wire ground connector in good condition. Use a meter to measure

third-wire ground continuity for 0.1 ohm or less between the external

ground pin and the frame ground.

b. The power cord should be the type specified in the parts list.

c. Insulation must not be frayed or worn.

4. Check for cracked or bulging batteries.

5. Remove the cover.

6. Check for any obvious non-ThinkPad alterations. Use good judgment as to the

safety of any non-ThinkPad alterations.

7. Check inside the unit for any obvious unsafe conditions, such as metal filings,

contamination, water or other liquids, or signs of fire or smoke damage.

8. Check for worn, frayed, or pinched cables.

9. Check that the power-supply cover fasteners (screws or rivets) have not been

removed or tampered with.

Safety information 5

Handling devices that are sensitive to electrostatic discharge

Any computer part containing transistors or integrated circuits (ICs) should be

considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when

there is a difference in charge between objects. Protect against ESD damage by

equalizing the charge so that the machine, the part, the work mat, and the person

handling the part are all at the same charge.

When handling ESD-sensitive parts:

v Keep the parts in protective packages until they are inserted into the product.

v Avoid contact with other people.

v Wear a grounded wrist strap against your skin to eliminate static on your body.

v Prevent the part from touching your clothing. Most clothing is insulative and

retains a charge even when you are wearing a wrist strap.

v Use a grounded work mat to provide a static-free work surface. The mat is

especially useful when handling ESD-sensitive devices.

v Select a grounding system, such as those listed below, to provide protection that

meets the specific service requirement.

– Attach the ESD ground clip to any frame ground, ground braid, or green-wire

ground.

– When working on a double-insulated or battery-operated system, use an ESD

common ground or reference point. You can use coax or connector-outside

shells on these systems.

– Use the round ground prong of the ac plug on ac-operated computers.

Grounding requirements

Electrical grounding of the computer is required for operator safety and correct

system function. Proper grounding of the electrical outlet can be verified by a

certified electrician.

Notes:

1. Use product-specific ESD procedures when they exceed the requirements

noted here.

2. Make sure that the ESD protective devices you use have been certified (ISO

9000) as fully effective.

Note:

The use of a grounding system to guard against ESD damage is desirable but not

necessary.

6 ThinkPad T400s Hardware Maintenance Manual

Safety notices (multilingual translations)

The safety notices in this section are provided in the following languages:

v English

v Arabic

v Brazilian Portuguese

v French

v German

v Hebrew

v Japanese

v Korean

v Spanish

v Traditional Chinese

Safety information 7

DANGER

Before the computer is powered on after FRU replacement, make sure all screws,

springs, and other small parts are in place and are not left loose inside the computer.

Verify this by shaking the computer and listening for rattling sounds. Metallic parts or

metal flakes can cause electrical shorts.

DANGER

Some standby batteries contain a small amount of nickel and cadmium. Do not

disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it.

Dispose of the battery as required by local ordinances or regulations. Use only the

battery in the appropriate parts listing. Use of an incorrect battery can result in ignition

or explosion of the battery.

DANGER

The battery pack contains small amounts of nickel. Do not disassemble it, throw it into

fire or water, or short-circuit it. Dispose of the battery pack as required by local

ordinances or regulations. Use only the battery in the appropriate parts listing when

replacing the battery pack. Use of an incorrect battery can result in ignition or explosion

of the battery.

DANGER

The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it,

remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it,

or expose its cell contents to water. Dispose of the battery as required by local

ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an

incorrect battery can result in ignition or explosion of the battery.

DANGER

If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your

hands, immediately wash the affected areas with water for at least 15 minutes. Seek

medical care if any symptoms from the fluid are present after washing.

8 ThinkPad T400s Hardware Maintenance Manual

DANGER

To avoid shock, do not remove the plastic cover that protects the lower part of the

inverter card.

DANGER

Though the main batteries have low voltage, a shorted or grounded battery can produce

enough current to burn personnel or combustible materials.

DANGER

Unless hot swap is allowed for the FRU being replaced, do as follows before removing

it: power off the computer, unplug all power cords from electrical outlets, remove the

battery pack, and disconnect any interconnecting cables.

Safety information 9

10 ThinkPad T400s Hardware Maintenance Manual

Safety information 11

PERIGO

Antes de ligar o computador após a substituição da FRU, certifique-se de que todos os

parafusos, molas e outras peças pequenas estejam no lugar e não estejam soltos dentro

do computador. Verifique isso sacudindo o computador e procurando ouvir sons de

peças soltas. Peças metálicas ou lascas de metal podem causar curto-circuito.

PERIGO

Algumas baterias reserva contêm uma pequena quantidade de níquel e cádmio. Não

desmonte uma bateria reserva, recarregue-a, jogue-a no fogo ou na água, ou deixe-a

entrar em curto-circuito. Descarte a bateria conforme requerido pelas leis ou

regulamentos locais. Use somente a bateria nas partes listadas apropriadas. O uso de

uma bateria incorreta pode resultar em combustão ou explosão da bateria.

PERIGO

O pacote da bateria contém uma pequena quantidade de níquel. Não o desmonte,

jogue-o no fogo ou na água, ou deixe-o entrar em curto-circuito. Descarte o pacote da

bateria conforme requerido pelas leis ou regulamentos locais. Use somente a bateria nas

partes listadas apropriadas ao substituir o pacote da bateria. O uso de uma bateria

incorreta pode resultar em combustão ou explosão da bateria.

PERIGO

A bateria de lítio pode causar incêndio, explosão ou graves queimaduras. Não a

recarregue, remova seu conector polarizado, desmonte-a, aqueça-a acima de 100°C

(212°F), incinere-a, ou exponha o conteúdo de sua célula à água. Descarte a bateria

conforme requerido pelas leis ou regulamentos locais. Use somente a bateria nas partes

listadas apropriadas. O uso de uma bateria incorreta pode resultar em combustão ou

explosão da bateria.

PERIGO

Se o LCD quebrar e o fluido de dentro dele entrar em contato com seus olhos ou com

suas mãos, lave as áreas afetadas imediatamente com água durante pelo menos 15

minutos. Procure cuidados médicos se algum sintoma causado pelo fluido surgir após a

lavagem.

12 ThinkPad T400s Hardware Maintenance Manual

Page is loading ...

Lenovo ThinkPad T400s Hardware Maintenance Manual

Related papers

Other documents