Exerpeutic 1302.4 Owner's manual

Elliptical

IMPORTANT: Read all instructions carefully before using this product.

Retain this owner’s manual for future reference.

The specifications of this product may vary from this photo, subject to change

without notice.

OWNER’S MANUAL

1302.4-031016

SERVICE ------------------------------------------------------------------------ 2

LABEL PLACEMENT --------------------------------------------------------- 3

PRODUCT SAFETY ---------------------------------------------------------- 4

OVERVIEW DRAWING ------------------------------------------------------ 5

PART LIST ----------------------------------------------------------------------- 6

HARDWARE PACK------------------------------------------------------------ 7

ASSEMBLY ---------------------------------------------------------------------- 8

COMPUTER -------------------------------------------------------------------- 16

ADJUSTMENTS --------------------------------------------------------------- 17

MOVING THE ELLIPTICAL ------------------------------------------------- 18

TROUBLE SHOOTING & MAINTENANCE ----------------------------- 19

WARRANTY -------------------------------------------------------------------- 20

PARTS REQUEST FORM --------------------------------------------------- 21

TABLE OF CONTENTS

1

IMPORTANT: FOR NORTH AMERICA ONLY

For damaged or defective products, questions, replacement parts or any

other needed service support, please contact our customer service

department (8:00 AM - 5:00 PM Pacific Standard Time, Daily) by below

methods:

For Best Service Email:

Service@paradigmhw.com *

Website:

www.paradigmhw.com

Toll-Free:

1-844-641-7921**

Please have the following information ready when requesting for service:

Your name

Phone number

Model number

Serial number

Part number

Proof of Purchase

For damaged or defective products please contact our customer service

before returning to the store.

* Emailing us with the information above will be the best method to

receive a response during peak business hours.

**Response time may vary.

Paradigm Health & Wellness, Inc.

1189 Jellick Ave.

City of Industry, CA 91748, USA

SERVICE

2

LABEL PLACEMENT

3

Basic precautions should always be followed, including the following safety

instructions when using this equipment: Read all the instructions before

using this equipment.

1. Read all the instructions in this manual and do warm up exercises before using

this equipment.

2. Before exercising, and in order to avoid injuring your muscles, warm-up

exercises for every muscle group are highly recommended.

3. Please make sure all components are not damaged and in working order before

use. This equipment should be placed on a flat surface while in use. Using a

mat or other material on the ground is recommended.

4. Please wear proper clothes and shoes when using this equipment; do not wear

clothes that might catch in any part of the equipment.

5. Do not attempt any maintenance or adjustments other than those described in

this manual. Should any problems arise, discontinue use and consult Customer

Service.

6. Be careful when stepping on or leaving the pedals. Always hold the

handlebars first and make sure the pedal at your side is at its lowest position.

Step on the pedal, and stride over the main frame then step on the other pedal.

When using, please hold onto the handlebars. To ensure the pedals run

smoothly push or pull on the handlebars first, then follow with leg motion.

When stepping off the machine, make sure one pedal is at its lowest position

and step off the pedal at the highest position first before stepping off of the

lowest pedal.

7. Do not use the equipment outdoors.

8. This equipment is for household use only.

9. Only one person should be on the equipment while in use.

10. Keep children and pets away from the product while in use. This machine

is designed for adults only. This product requires a minimum of 6 square feet

of space for safe operation.

11. If you feel any chest pains, nausea, dizziness, or shortness of breath, you

should stop exercising immediately and consult your physician before continuing.

12. The maximum weight capacity for this product is 300 lbs/136 kgs.

WARNING: Before beginning any exercise program consult your

physician. This is especially important for the persons who are over 35

years old or who have pre-existing health problems. Read all instructions

Before using any fitness equipment.

CAUTION: Read all instructions carefully before operating this

product. Retain this Owner’s Manual for future reference.

PRODUCT SAFETY

4

OVERVIEW DRAWING

5

No.

Description

Qty

No.

Description

Qty

001

Main Frame 80x40x2

1

030R

Foot Bar Cover-B

2

002L

Left Foot Bar 40x25x1.5

1

033

Left Foot Pedal 395x150x65

1

002R

Right Foot Bar 40x25x1.5

1

034

Right Foot Pedal 395x150x65

1

003L

Left Handrail Arm Ø32x1.5

1

038

Hexagon Socket Head Bolt M8x15

10

003R

Right Handrail Arm Ø32x1.5

1

040

Hexagon Socket Head Bolt M8x20

2

004L

Left Handrail Ø32x1.5

1

041

Spring Washer Ø8

10

004R

Right Handrail Ø32x1.5

1

042

Washer Ø38x3

2

005

Front Post Ø60x1.5

1

044

Carriage Bolt M6x35

4

006

Handlebar Ø25x1.5

1

045

Curve Washer Ø6

4

007

Front Stabilizer Ø60x1.5x600

1

046

Big Washer Ø8

2

008

Rear Stabilizer Ø60x1.5x600

1

048

Plastic Bushing Ø32xØ16x5xØ50

2

009

Carriage Bolt M8x70

4

049L

Left Handrail Arm Cover-A

1

010

Rear Stabilizer Levelers

2

049R

Right Handrail Arm Cover-A

1

011

Big Curve Washer Ø20xØ8

12

050L

Left Handrail Arm Cover-B

1

012

Cap Nut M8

4

050R

Right Handrail Arm Cover-B

1

013L

½” Left Bracket Bolt

1

051

Tension Control Knob

1

013R

½” Right Bracket Bolt

1

053

Console (JVT29121)

1

014L

½” Left Nylon Nut

1

054

Rear Cover Ø60

1

014R

½” Right Nylon Nut

1

055

Hand Pulse Sensor with Wire

L=750

2

015

Wave Washer Ø28xØ17x0.3

2

060

Phillips Self Tapping Screw

ST4.2x25

4

017

Spring Washer Ø20

2

061

Curve Washer for Tension Control

Knob Ø20xØ5.2

1

020

U Shaped Bracket

2

062

Bolt for Tension Control Knob

M5x55

1

023

Bolt M8x45

2

064

Sensor Wire I L=1100

1

024

Nylon Nut M6

10

065

Sensor Wire II L=1300

1

025

Washer Ø6

6

075

Crank

1

026

Bolt M6x40

6

088

Bolt M5x10

2

027

Tension Cable L=1800

1

090

Front Cover Ø60

1

028

Cap S13

2

093

Curve Washer Ø16xØ8

2

029

Screw ST4.2x25

2

094

Screw ST4.2*15

8

030L

Foot Bar Cover-A

2

096

Clip

1

PART LIST

6

HARDWARE PACK

7

1. Front and Rear Stabilizers Installation:

Step A: Align the Front Stabilizer (7) onto the front curve of the Main frame (1). Make

sure the transport wheels are positioned toward the front and parallel to the floor. Install

two Carriage Bolts (9) from the bottom, and on the other ends of the bolts attach two Big

Curve Washers (11) and two Cap Nuts (12). Use the Multi Hex Tool with Phillips

Screwdriver to tighten the Cap Nuts (12) until secure.

Step B: Align and Install the Rear Stabilizer (8) onto the rear curve of the Main frame (1)

using two Carriage Bolts (9), two Big Curve Washers (11), and two Cap Nuts (12).

Securely tighten the Cap Nuts (12) with the Multi Hex Tool with Phillips Screwdriver

provided.

Hardware:

ASSEMBLY

8

(9) Carriage Bolt

M8x70

4 PCS

(11) Big Curve Washer

4 PCS

(12) Cap Nut M8

4 PCS

Multi Hex Tool with Phillips Screwdriver

S8, S13, S14, S15

1 PC

MUST TIGHTEN IN SEQUENCE: A,B,C,D,E,F,G,H.

2. Front Post and Tension Control Knob Installation

Remove the eight Hexagon Socket Head Bolts (38), eight Big Curve Washers (11), and eight

Spring Washers (41) from the Main Frame (1) first. Insert the Tension Cable (27) into the Front

Post (5) and pull it out through the square hole on the top of the Front Post (5). Connect the

Sensor Wires (64) and (65). Make sure the wires stay connected. Then secure the Front Post (5)

to the Main Frame (1) using the eight Hexagon Socket Head Bolts (38), eight Big Curve Washers

(11), and eight Spring Washers (41) that were previously removed. Tighten with the 6mm Allen

Wrench provided. Remove the Bolt (62) and Curve Washer (61) from the back of the Tension

Control Knob (51). Turn the Tension Control Knob (5) to the highest tension setting. Attach the

end of the resistance cable on the Tension Control Knob (51) into the spring hook of the Tension

Cable (27) (See Figure A). Pull the Resistance Cable of the Tension Control Knob (51) up and

gently remove the Clip (96) (See Figure B). Install the Tension Control Knob (51) in to the Front

Post (5) using the Bolt (62) and Curve Washer (61) previously removed. Then tighten with the

Multi Hex tool with Phillips Screwdriver provided.

ASSEMBLY

9

6mm Allen Wrench

1 PC

Multi Hex Tool with Phillips Screwdriver

S8, S13, S14, S15

1 PC

ASSEMBLY

10

3. Handrail Arm Installation

Remove the Pre-Installed Hexagon Socket Head Bolts (40), Spring Washers (41), Big

Washers (46), and Washers (42) from the left and right horizontal posts on the Front

Post (5). Slide a Plastic Bushing (48) down the horizontal shaft on the left side of

Front Post (5), and then attach the Left Handrail Arm (3L) onto the left horizontal post

on the Front Post (5). Secure it using one Hexagon Socket Head Bolt (40), one Spring

Washer (41), one Big Washer (46), and one Washer (42) that was removed

previously. Tighten the Hexagon Socket Head Bolt (40) using the 6mm Allen Wrench

provided.

*Repeat this step for the Right Handrail Arm (3R).

6mm Allen Wrench

1 PC

ASSEMBLY

11

4. Foot Bar Installation

Insert the Left Bracket Bolt (13L) along with a Wave Washer (15) through the U Shaped Bracket

(20) located on the back of the Left Foot Bar (2L). Secure the Left Bracket Bolt (13L) to the Left side

of the Crank (75) by turning the Bolt Counter-Clockwise. Tighten the Left Bracket Bolt with the

8mm Allen Wrench provided. Next, install a Spring Washer (17) and Left Nylon Nut (14L) on the

remaining threads of the Left Bracket Bolt (13L). Turn the Left Nylon Nut (14L) in a Clockwise

direction, and then tighten using the 8mm Allen Wrench and Multi Hex Tool Provided. Then place

the Cap (28) onto the Head of the Bolt (23).

*Repeat these steps for the Right Foot Bar (2R).

NOTE: Before attaching the Nylon Nut (14L) be sure that the Left Bracket Bolt (13L) is screwed as

far into the Crank (75) as possible (See Figure C).

In order to install the Bracket Bolts properly, keep it

perfectly straight while screwing into the threaded hole of

the Crank (75). If the Bracket Bolt is inserted incorrectly it

may cause damage to the threads (See Figure C).

CORRECT

INCORRECT

13L

13R

Important:

Turn the Right Bracket Bolt (13R) in a Clockwise

direction.

Turn the Left Bracket Bolt (13L) in a

Counter-Clockwise direction. (See Figure D)

8mm Allen Wrench

1 PC

Multi Hex Tool

1 PC

Hardware:

(17) Spring Washer

Ø20 2PCS

(15) Wave Washer

Ø28xØ17x0.3

2PCS

(13R/L) Right / Left

Bracket Bolt 1/2”

2PCS

(14R/L) Right / Left

Nylon Nut 1/2”

2PCS

(28) Cap S13

2 PCS

C

D

--------------------------------------------------------------------------------------------------------------------------------------------

ASSEMBLY

12

6. Foot Bar Cover Installation

Attach the Foot Bar Covers A/B (30L,30R) onto the Left Foot Bar (2L) using one screw (29) and

two Phillips Self Tapping Screws (60). Tighten using the Multi Hex Tool with Phillips Screwdriver

provided.

*Repeat these steps for the Right Foot Bar (2R).

(60) Phillips Self Tapping

Screw ST4.2x25

4 PCS

(29) Screw

ST4.2x25

2PCS

Hardware:

Multi Hex Tool with Phillips Screwdriver

S8, S13, S14, S15

1 PC

5. Pedal Installation

Install the Left Foot Pedal (33) onto the Left Foot Bar (2L) using three Bolts (26), three Washers

(25) and three Nylon Nuts (24). Tighten the Nylon Nuts (24) using the Multi Hex Tool with Phillips

Screwdriver.

*Repeat these steps for the Right Foot Pedal (34).

(24) Nylon Nut M6

6 PCS

(25) Washer Ø6

6 PCS

(26) Bolt M6x40

6 PCS

Multi Hex Tool with Phillips Screwdriver

S8, S13, S14, S15

1 PC

Hardware:

(28) Cap

S13, 2 PCS

(44) Carriage Bolt

M6x35

4 PCS

(45) Curve Washer

Ø6

4 PCS

(24) Nylon Nut

M6

4 PCS

7. Handrail Installation

Attach the Left Handrail (4L) onto the Left Handrail Arm (3L) using two Carriage

Bolts (44), two Curve Washers (45) and two Nylon Nuts (24). Tighten the Nylon

Nuts (24) with the Multi Hex Tool with Phillips Screwdriver provided.

*Repeat these steps for the Right Handrail (4R) and Right Handrail Arm

(3R).

ASSEMBLY

Multi Hex Tool with Phillips Screwdriver

S8, S13, S14, S15

1 PC

Hardware:

13

ASSEMBLY

14

8. Computer Installation

Remove the two Bolts (88) from the back of the Console (53). Then remove the two Bolts (38)

and two Curve Washers (93) from the Front Post (5).

Insert the Hand Pulse Sensor Wires (55) from the Handlebar (6) into the hole on the forward

facing side of the Front Post (5), and pull them up, and out of the top end of the Front Post (5).

Connect the Hand Pulse Sensor Wires (55) to the Sensor Wires coming from the back of the

Console (53). Then connect the Sensor Wire I (64) to the connection wire coming from the

back of the Console (53) (See Figure D). Place the Console (53) onto the plate on the Front

Post (5) and secure it into place using the two Bolts (88) and tighten using the Multi Hex Tool

with Phillips Screwdriver.

Install the Handlebar (16) onto the Front Post (5) using the two Bolts (38) and two Curve

Washers (93) that were previously removed. Then tighten using the 6mm Allen Wrench

provided.

Multi Hex Tool with Phillips

Screwdriver

S8, S13, S14, S15

1 PC

6mm Allen Wrench

1 PC

9. Cover Installation

Attach the Front and Rear Covers (90, 54) onto the Front Post (5) using two Screws (29).

Then, tighten using the Multi Hex Tool with Phillips Screwdriver.

Attach the Left Handrail Arm Cover-A (49L) and Left Handrail Arm Cover-B (50L) onto the Left

Handrail Arm (3L) with four Screws (94) and tighten using the Multi Hex Tool with Phillips

Screwdriver.

*Repeat these steps for the Right Handrail Arm (3R).

(94) Screw

ST4.2x15, 8 PCS

(29) Screw

ST4.2x25, 2 PCS

Multi Hex Tool with

Phillips Screwdriver

S8, S13, S14, S15

1 PC

15

Hardware:

ASSEMBLY

Button functions:

MODE: Press to change the current statistics being displayed.

Hold for 3 seconds to reset all the workout statistics to 0, except odometer.

SET: Use to set a goal value for TIME, DISTANCE, CALORIES, or PULSE.

RESET: Resets the current exercise values, as well as goal values.

Hold for 3 seconds to reset all the workout statistics to 0, except odometer.

Display functions:

SCAN Automatically switches through all the display functions every 6 seconds.

TIME Displays the time exercised.

SPEED Displays the current speed.

DISTANCE Displays the distance traveled during the current workout session.

CALORIES Displays the calories burned during the current workout session.

ODOMETER Displays the cumulative distance traveled from all workout sessions.

This data is a rough guide for comparison of different exercise sessions and should not be

used as a basis for medical treatment.

Set a goal value:

When an exercise goal has been set, the value (Time, Distance, or Calories) will count down

until the goal has been met.

Press SET to assign a value, and then start your workout.

You can also set a Target Heart Rate to keep up with during your workout.

COMPUTER

16

Adjusting the Tension Control Knob

To increase the resistance, turn the Tension Control

Knob (51) in a CLOCKWISE direction.

To decrease the resistance, turn the Tension Control

Knob (51) in a COUNTER-CLOCKWISE direction.

Adjusting the Rear Stabilizer End Cap

Turn the Rear Stabilizer End Caps (10) on the

Rear Stabilizer (8) as needed to level the

Elliptical.

ADJUSTMENTS

17

Transporting the Elliptical

Hold the Handlebar (6) and pull the machine until the wheels on the Front Stabilizer

(7) make contact with the floor. Push or pull the unit to the desired location, then

gently lower the Rear Stabilizer (8) to the ground.

MOVING THE ELLIPTICAL

18

Page is loading ...

Exerpeutic 1302.4 Owner's manual

Exerpeutic 1302.4 Owner's manual

Related papers

Other documents