BMW DWA 5.1 Rider's Manual

BMW Motorrad

Rider's Manual (US Model)

Anti-Theft Alarm DWA 5.1

The Ultimate

Riding Machine

Motorcycle/Retailer Data

Motorcycle data

Model

Vehicle Identification Number

Color number

First registration

Registration number

Retailer Data

Contact in Service

Ms./Mr.

Phone number

Retailer's address/phone number (com-

pany stamp)

Welcome to BMW

Congratulations on your purchase

of this BMW anti-theft alarm

(DWA).

It makes it more difficult for po-

tential thieves to practice their

trade and reduces operation to

an absolute minimum.

If you have any questions con-

cerning your anti-theft alarm,

your authorized BMW Motorrad

retailer is always happy to provide

advice and assistance.

We wish you pleasant reading

with this Rider's Manual and

many miles of safe and enjoyable

riding

BMW Motorrad.

Table of Contents

You can also use the index at the

end of this Rider's Manual to find

a specific topic.

1 General instructions .... 3

Overview . . . . . . . . . . . . . . . . . . . . . 4

Abbreviations and

symbols . . . . . . . . . . . . . . . . . . . . . . 4

Currentness of this man-

ual . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Technical data . . . . . . . . . . . . . . . 4

2 Overview ................. 5

General Information on Anti-

Theft Alarm . . . . . . . . . . . . . . . . . . 6

Controls . . . . . . . . . . . . . . . . . . . . . . 6

Code card . . . . . . . . . . . . . . . . . . . . 7

3 Operation................. 9

Activation . . . . . . . . . . . . . . . . . . . 10

Alarm function. . . . . . . . . . . . . . . 11

Deactivation . . . . . . . . . . . . . . . . . 13

Programming . . . . . . . . . . . . . . . . 14

Logging on remote con-

trol . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Synchronization . . . . . . . . . . . . . 17

Battery . . . . . . . . . . . . . . . . . . . . . . 17

4 Technical data . . . . . . . . . . 19

Anti-theft alarm. . . . . . . . . . . . . . 20

Remote control. . . . . . . . . . . . . . 20

5 Index . . . . . . . . . . . . . . . . . . . . . 21

General instructions

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Abbreviations and symbols . . . . . . . . . . 4

Currentness of this manual . . . . . . . . . . 4

Technical data . . . . . . . . . . . . . . . . . . . . . . . 4

General instructions

Overview

Chapter 2 of this Rider's Man-

ual contains an overview of the

anti-theft alarm. Chapter 3 de-

scribes the operation of the anti-

theft alarm, and Chapter 4 lists

its most important technical fea-

tures.

Abbreviations and

symbols

Indicates warnings that

you must comply with for

reasons of your safety and the

safety of others, and to protect

your motorcycle against damage.

Special information on op-

erating and inspecting your

motorcycle as well as mainte-

nance and adjustment proce-

dures.

Indicates the end of an

item of information.

Instruction.

Result of an activity.

Reference to a page with

more detailed informa-

tion.

Indicates the end of ac-

cessory or equipment-

dependent information.

Tightening torque.

Technical data.

Currentness of this

manual

The high safety and quality level

of BMW accessories is ensured

with continuous further develop-

ment. This can result in possible

differences between these op-

erating instructions and those of

the accessories you have pur-

chased. In addition, BMW Motor-

rad cannot guarantee the total

absence of errors. We hope you

will appreciate that no claims can

be entertained on the basis of

the data, illustrations or descrip-

tions in this manual.

Technical data

All dimensions, weights and out-

puts in the Rider's Manual refer

to the Deutsches Institut für Nor-

mung e. V. (DIN) and comply with

its tolerance regulations. Ver-

sions for individual countries may

differ.

General instructions

Overview

General Information on Anti-Theft

Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Code card . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Overview

General Information on

Anti-Theft Alarm

The anti-theft alarm consists

of an immobilizer and an alarm

function with a motion sensor.

The immobilizer prevents the

unauthorized starting of the en-

gine, the alarm function triggers

an alarm on any attempt to move

the motorcycle, to change its po-

sition or to disconnect the motor-

cycle battery.

The sensitivity of the system is

designed so that slight jolts to

the motorcycle do not trigger an

alarm.

You can adjust the behavior

of the anti-theft alarm to your

wishes in partial areas.

Protecting battery

To protect the motorcycle bat-

tery and to maintain starting abil-

ity, the activated anti-theft alarm

automatically switches off the

alarm function after several days.

However, it remains active for at

least seven days. The immobi-

lizer is not deactivated.

Radio interference

Radio systems or devices which

transmit on the same frequency

as the remote control of the anti-

theft alarm can interfere with its

operation. In case of problems of

this kind, point the remote con-

trol at the motorcycle from a dif-

ferent direction.

Splash-water protection

The remote control is splash-wa-

ter protected, however it is not

waterproof. To ensure its proper

operation, BMW Motorrad rec-

ommends protecting the remote

control against heavy rainfall.

Controls

1 Left-hand button (corru-

gated) ( 10)

2 Right-hand button ( 12)

3 LED

4 Anti-theft alarm indicator

LED on motorcycle

For the position of the in-

dicator LED on the mo-

torcycle, please see the Rider's

Manual of your motorcycle.

Overview

Code card

The anti-theft alarm is delivered

with a sealed envelope which

contains the code card 1. This

code card contains the secret

code (remove sticker) for deac-

tivating the anti-theft alarm with

the ignition.

The secret code is stamped onto

the anti-theft alarm in encrypted

form and is also contained in the

delivery scope as a sticker 2.

You should apply the sticker at

a concealed location on the mo-

torcycle.

Should you forget the secret

code and loose the code card,

then your authorized BMW

Motorrad retailer can ask BMW

for your secret code using the

numeric code.

Overview

Operation

Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Alarm function . . . . . . . . . . . . . . . . . . . . . . 11

Deactivation . . . . . . . . . . . . . . . . . . . . . . . . 13

Programming . . . . . . . . . . . . . . . . . . . . . . . 14

Logging on remote control . . . . . . . . . . 15

Synchronization . . . . . . . . . . . . . . . . . . . . . 17

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Operation

Activation

Activation without remote

control

Switch off ignition.

Activation by switching

off the ignition must be

programmed. The following

can be programmed:

Automatic activation of immo-

bilizer without alarm function

(factory setting).

Automatic activation of immobi-

lizer with alarm function.

Programming anti-theft alarm

( 14).

50 seconds are required to ac-

tivate the programmed func-

tions. The indicator LED does

not light up during this time.

Another 15 seconds are re-

quired for the activation; this is

indicated by rapid flashing of

the indicator LED (0.1 sec. on,

0.5 sec. off). The LED does

not flash if only the immobilizer

is activated.

After completing the activa-

tion, the turn indicators light

up twice and the acknowledg-

ment tone sounds twice (if pro-

grammed).

The anti-theft alarm is now ac-

tive; this is indicated by slow

flashing of the indicator LED

(0.1 sec. on, 0.9 sec. off). The

LED does not flash if only the

immobilizer is activated.

Activation with remote

control

Switch off ignition.

Press button 1 of remote con-

trol.

The immobilizer and the alarm

function are always activated

with the remote control.

15 seconds are required for

the activation; this is indicated

by rapid flashing of the indica-

tor LED (0.1 sec. on, 0.5 sec.

off).

After completing the activa-

tion, the turn indicators light

up twice and the acknowledg-

ment tone sounds twice (if pro-

grammed).

The anti-theft alarm is now ac-

tive; this is indicated by slow

flashing of the indicator LED

(0.1 sec. on, 0.9 sec. off).

Drained battery

If the alarm tone sounds four

times following activation, then

the internal anti-theft alarm bat-

tery is discharged. No alarm can

be triggered when the anti-theft

Operation

alarm is disconnected from the

motorcycle battery.

To charge the anti-theft alarm

internally:

Drive for a longer time, or

Leave ignition switched on for

a longer time and connect a

trickle-charger to motorcycle

battery

Motion sensor when

transporting motorcycle

If, for example, the motorcycle

is to be transported by train, it is

advisable to switch off the motion

sensor. The strong movements

could result in the alarm acciden-

tally being triggered.

Deactivating motion

sensor

Press button 1 of remote con-

trol again during activation

phase.

Turn indicators light up three

times.

Acknowledgment tone sounds

three times.

Motion sensor is deactivated.

Alarm function

Triggering alarm

The alarm can be triggered by

the motion sensor

switching on the ignition with-

out deactivating the anti-theft

alarm beforehand

disconnecting the anti-theft

alarm from the vehicle bat-

tery (anti-theft alarm battery

assumes the power supply -

alarm tone only, no lighting up

of the turn signals)

If the internal anti-theft alarm bat-

tery is discharged, all functions

are maintained; only the alarm

triggering when the motorcy-

cle battery is disconnected is no

longer possible.

If only the immobilizer is active,

then no alarm will be triggered

after switching on the ignition

without prior deactivation of the

Operation

anti-theft alarm. Instead, the indi-

cator LED lights up.

Alarm

The duration of the alarm is

26 seconds. After another

12 seconds, the alarm is active

again. A triggered alarm can

be interrupted at any time by

pressing the button 2 of the

remote control. This function

does not change the state of the

anti-theft alarm.

Pressing the button 2 again de-

activates the DWA.

During the alarm, an alarm tone

sounds and the turn indicators

flash. The type of alarm tone can

be programmed.

Reason for an alarm being

triggered

After the anti-theft alarm has

been deactivated, the anti-theft

alarm indicator LED signals the

reason for a possible triggering of

the alarm for one minute:

1x flashing: motion sensor

2x flashing: ignition switched

on with anti-theft alarm armed

3x flashing: disconnection of

anti-theft alarm from vehicle

battery

This display goes out after a

minute, or when the ignition is

switched on. If several alarms

have been triggered, all causes

are shown. To request the rea-

son for the last triggering of an

alarm at a later time, proceed as

described in the following sec-

tion.

Requesting reason for an

alarm being triggered

Deactivating anti-theft alarm

( 13).

Switch on ignition.

Switch ignition off and then on

again 3x within 4 seconds.

Indicator LED lights up; ac-

knowledgment tone sounds

once.

Switch off ignition within 15

seconds and watch indicator

LED on motorcycle.

Indicator LED flashes

Count LED signals until num-

ber of signals is equal to first

number of secret code.

Switch on ignition.

Indicator LED goes out.

Repeat previous steps for addi-

tional numbers of secret code.

A maximum of three incor-

rect entries are permitted,

then the anti-theft alarm is acti-

vated for another ten minutes.

Operation

Acknowledgment tone sounds

twice.

Identification completed.

Switch off ignition.

The reason for the last alarm

triggering is shown.

Deactivation

Deactivating anti-theft

alarm

Press button 2 of remote con-

trol.

If the anti-theft alarm has

automatically been acti-

vated by switching off the igni-

tion, then it becomes active again

after 50 seconds without switch-

ing on the ignition.

Turn signals light up once.

Acknowledgment tone sounds

once (if programmed).

Anti-theft alarm is deactivated.

Deactivating anti-theft

alarm following automatic

switch-off

If the anti-theft alarm no longer

reacts to the remote control

while activated, the automatic

switch-off is active.

Switch on ignition.

Alarm is triggered (if

programmed)

Press button 2.

Alarm is canceled.

Deactivating anti-theft alarm

( 13).

Deactivating anti-theft

alarm without remote

control

To deactivate anti-theft alarm

without remote control: enter

secret number as described

below.

Switch on ignition.

The alarm is triggered with the

alarm function activated.

Switch off ignition and watch

indicator LED.

Indicator LED flashes and alarm

continues.

Count LED signals until num-

ber of signals is equal to first

number of secret number.

Switch on ignition.

Indicator LED goes out.

Repeat previous steps for fur-

ther numbers of secret num-

ber.

A maximum of three incor-

rect entries are permitted,

Operation

then the anti-theft alarm is acti-

vated for another ten minutes.

Turn signals light up once.

Acknowledgment tone sounds

once (if programmed).

Anti-theft alarm is deactivated.

Programming

Programming options

The behavior of the anti-theft

alarm can be adjusted in the fol-

lowing areas:

Acknowledgment tone follow-

ing activation/deactivation of

anti-theft alarm in addition to

turn signals lighting up.

Rising and falling or intermittent

alarm tone.

Automatic activation of the

alarm function when the igni-

tion is switched off.

Automatic activation of the im-

mobilizer when the ignition is

switched off.

In the course of programming,

the number of flashing signals of

the indicator on the motorcycle is

equal to the active programming

step. Each press of the button is

confirmed with the acknowledg-

ment tone.

Programming anti-theft

alarm

Deactivate anti-theft alarm.

Switch on ignition and wait un-

til indicator LED on motorcycle

goes out.

Press button 2 once.

Indicator LED on motorcycle

lights up briefly.

Switch off ignition within ten

seconds.

Indicator LED on motorcycle

flashes (number of flashing

signals is equal to number of

connected remote controls).

Consecutively press and hold

the button 2 three times

quickly for approx. half a

second each time.

Turn indicators light up.

Switch on ignition within ten

seconds.

Acknowledgment tone sounds

three times.

Programming function is active.

1. Acknowledgment tone after

activating/deactivating anti-theft

alarm:

Press button 1 to activate ac-

knowledgment tone.

Press button 2 to deactivate

acknowledgment tone.

Operation

2. Type of alarm tone:

Press button 1 to obtain a rais-

ing and falling tone.

Press button 2 to obtain an

intermittent tone.

3. Automatic activation of alarm

function after switching off igni-

tion:

Press button 1 to switch on

activation.

Press button 2 to switch off

activation.

4. Automatic activation of immo-

bilizer after switching off ignition:

Press button 1 to switch on

activation.

Press button 2 to switch off

activation.

Switching off the function

"Activation of immobilizer

with ignition off" automatically

causes the function "Activation of

alarm function with ignition off" to

switched off.

The acknowledgment tone

sounds four times; program-

ming is completed.

When is programming

canceled?

Programming is canceled

by switching off the ignition

before the last programming

step, or

if more than 10 seconds have

past between two program-

ming steps.

If the programming is canceled,

the data are not saved.

Factory settings

The anti-theft alarm is delivered

with the following factory set-

tings:

Acknowledgment tone follow-

ing activation/deactivation of

anti-theft alarm: off

Alarm tone: rising and falling

Automatic activation of alarm

function when switching off

ignition: off

Automatic activation of immobi-

lizer when switching off ignition:

Logging on remote

control

When is it necessary for

a remote control to be

logged on?

Should you want to log on an ad-

ditional remote control or replace

a lost remote control, you must

always log on all remote controls

with the anti-theft alarm. You can

log on a maximum of four remote

controls.

To determine how many remote

controls are logged on, watch

the anti-theft alarm indicator LED

on the motorcycle when switch-

ing off the ignition. The num-

ber of flashing signals is equal to

Operation

the number of logged-on remote

controls

Logging on remote

control

To log on a remote control:

enter the secret code as de-

scribed in the following:

Deactivate anti-theft alarm and

switch on ignition.

Switch ignition off and then

on again three times within 4

seconds.

Indicator LED lights up; ac-

knowledgment tone sounds

once.

Switch off ignition within 15

seconds and watch indicator

LED.

Count LED signals until num-

ber of signals is equal to first

number of secret code.

Switch on ignition.

Indicator LED goes out.

Repeat previous steps for addi-

tional numbers of secret code.

A maximum of three incor-

rect entries are permitted,

then the anti-theft alarm is acti-

vated for another ten minutes.

Acknowledgment tone sounds

twice.

Now all remote controls must

be logged on.

Press and hold button 1 and

button 2.

LED 3 flashes for ten seconds.

As soon as the LED 3 goes

out, release button 1 and but-

ton 2.

LED 3 lights up.

Press button 1 or button 2.

Acknowledgment tone sounds

once.

LED 3 off.

Repeat the three previous work

steps for each additional re-

mote control.

Logon ended

The logon is ended when

four remote controls have been

logged on

the ignition is switched off

after the ignition has been

switched off, no button has

been pressed for 30 seconds

after a remote control is

logged on, no button has been

pressed for 30 seconds

After the logon is ended, the

LED flashes and the acknowledg-

ment tone sounds three times.

Operation

Synchronization

When is it necessary to

synchronize the remote

control?

The remote control must be

synchronized if the buttons of

the remote control have been

pressed more than 256 times

outside the range of the receiver.

In this case, the receiver on the

motorcycle no longer reacts to

the signals of the remote control.

Synchronizing remote

control

Switch on ignition.

Press and hold button 1 and

button 2.

LED 3 flashes for ten seconds.

As soon as LED goes out, re-

lease button 1 and button 2.

LED 3 lights up.

Press button 1 or button 2.

LED goes out.

Remote control is synchro-

nized.

Battery

When is a battery

replacement required?

The batteries of the remote con-

trol must be replaced after ap-

prox. 2 - 3 years. A weak battery

can be recognized from the fact

that the LED does not light up at

all or only briefly when a button is

pressed.

Replacing battery

Remove screw 4 and take off

lower housing section 5.

Slide old battery 8 forward un-

der hoop 6.

Operation

Dispose of old battery in accor-

dance with legal regulations; do

not throw battery into house-

hold waste.

Batteries of the wrong type

or incorrect poling of the

batteries can destroy the device.

Use specified battery (see the

chapter "Technical Data"). En-

sure proper poling when inserting

the battery.

Mount new battery; while do-

ing so, make sure that positive

terminal of battery is located at

top.

Position lower housing sec-

tion on lug 9 of front edge and

close while watching two guide

pins 7.

Install screw 4.

The LED of the remote con-

trol lights up, i.e. the remote

control must be synchronized.

To synchronize the remote

control, press the button 1

twice within the range of the

receiver.

LED 3 begins to flash and

goes out after a few seconds.

The remote control is ready for

operation again.

Operation

Page is loading ...

BMW DWA 5.1 Rider's Manual

Related papers

Other documents