Cub Cadet 1X 21" LHP User manual

Type
User manual
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Safe Operation Practices • Set-Up • Operation • Maintenance • Troubleshooting • Warranty
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
OperatOrs Manual
Form No. 769-15010
(May 17 2018)
179cc, 208cc, 243cc & 272cc OHV Horizontal Shaft Engine
This Operator’s Manual is an important part of your new engine. It will help you prepare and maintain the engine for the best
performance. Please read and understand the contents before operating the engine.
Thank You
Customer Support
Please do NOT return the machine to the retailer or dealer without first contacting our Customer Support Department.
If you have difficulty with this product or have any questions regarding the controls, operation, or maintenance of this engine,
you can seek help from the experts. Choose from the options below:
Visit us on the web at www.mtdproducts.com
Call a Customer Support Representative at (800) 800-7310 or (330) 220-4683
Write us at MTD LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019
Model NuMber/Serial NuMber
/
Record Product Information
Before operating your new engine, please locate the model plate
on the engine and record the information in the provided area
to the right. This information will be necessary, should you seek
technical support via our web site or with your local dealer.
To The Owner
1
2
Safe Operation Practices ........................................ 3
Safety Symbols ........................................................ 4
Set-Up ....................................................................... 5
Controls & Features ................................................. 7
Operation ................................................................. 8
Maintenance ........................................................... 11
Troubleshooting .....................................................15
Replacement Parts .................................................16
Emission Statement/Warranty .................................
.....................................See Seperate Supplement
Spanish ....................................................................19
Table of Contents
Important Safe Operation Practices
2
3
WARNING!
This symbol points out important safety
instructions which, if not followed, could endanger
the personal safety and/or property of yourself
and others. Read and follow all instructions
in this manual before attempting to operate
the equipment. Failure to comply with these
instructions may result in personal injury. When
you see this symbol. HEED ITS WARNING!
WARNING!
CALIFORNIA PROPOSITION 65
Engine Exhaust, some of its constituents, and
certain vehicle components contain or emit
chemicals known to State of California to cause
cancer and birth defects or other reproductive
harm.
DANGER!
This engine was built to be operated according to
the safe operation practices in this manual. As with
any type of power equipment, carelessness or error
on the part of the operator can result in serious
injury. Failure to observe the following safety
instructions could result in serious injury or death.
Training
1. Read, understand and follow all
instructions on the engine and in the
manual(s) before attempting to assemble
and operate. Keep this manual in a safe
place for future and regular reference and
for ordering replacement parts.
2. Be familiar with all controls and their
proper operation. Know how to stop the
engine and disengage them quickly.
3. Never allow children under 14 years of
age to operate the engine. Children 14
and over should read and understand the
instructions and safe operation practices
in this manual and be trained and
supervised by an adult.
4. Never allow adults to operate the machine
without proper instruction.
5. Keep the area of operation clear of all
persons, particularly small children and
pets. Stop machine if anyone enters the
area.
Preparation
1. Wear sturdy, rough-soled work shoes and
close fitting slacks and shirts. Loose fitting
clothes or jewelry can be caught in the
moving parts. Never operate the machine
in bare feet or sandals.
2. Disengage clutch levers and shift (if
equipped) into neutral (“N) before
starting the engine.
3. Never leave the engine running while
unattended.
4. Never attempt to make any adjustments
while the engine is running, except
where specifically recommended in the
operator’s manual.
Safe Handling of Gasoline:
To avoid personal injury or property damage,
use extreme care in handling gasoline. Gasoline
is extremely flammable and the vapors are
explosive. Serious personal injury can occur
when gasoline is spilled on yourself and/or your
clothes which can ignite. Wash your skin and
change clothes immediately.
1. When adding fuel, turn engine OFF and
let engine cool at least 2 minutes before
removing the gas cap.
2. Fill fuel tank outdoors or in well ventilated
area.
3. Use only an approved gasoline container.
4. Never fill containers inside a vehicle or on
a truck or trailer bed with a plastic liner.
Always place containers on the ground
away from your vehicle before filling.
5. If possible, remove gas-powered
equipment from the truck or trailer and
refuel it on the ground. If this is not
possible, then refuel such equipment on
a trailer with a portable container, rather
than from a gasoline dispenser nozzle.
6. Keep the nozzle in contact with the rim of
the fuel tank or container opening at all
times until fueling is complete. Do not use
a nozzle lock-open device.
7. Do not overfill fuel tank. Fill tank to full
as indicated by the fuel level indicator
installed inside of the fuel tank or marked
on the tank. Do not over-fill to allow space
for fuel expansion. On some models, a fuel
level indicator may NOT be present, in this
instance, fill the tank no more than 1/2
inch below the bottom of the filler neck to
allow space for fuel expansion.
8. Replace fuel cap and tighten until the cap
ratchets.
9. If gasoline is spilled, wipe it off the engine
and the equipment. Move the machine
to another area. Wait five minutes before
starting the engine.
10. To reduce fire hazards, keep the machine
free of grass , leaves or other debris
build up. Clean up oil or fuel spillage and
remove any fuel-soaked debris.
11. Keep gasoline away from sparks, open
flames, pilot lights, heat, and other
ignition sources.
12. Never fuel equipment indoors because
flammable vapors will accumulate in the
area.
13. Extinguish all cigarettes, cigars, pipes, and
other sources of ignition.
14. Check fuel line, tank, cap, and fittings
frequently for cracks or leaks. Replace if
necessary.
Operation
1. When starting the engine, make sure spark
plug, muffler, and fuel cap are in place.
2. Do not crank engine with spark plug
removed.
3. If fuel spills, wait until it evaporates before
starting engine.
4. Allow muffler, engine cylinder, and fins to
cool before touching.
5. Keep children away from hot or running
engines. They can suffer burns from a hot
muffler.
6. Remove accumulated combustibles from
muffler and cylinder area.
7. Operate equipment with all guards in
place.
8. Keep hands and feet away from rotating
parts.
9. Tie up long hair and remove jewelry.
10. Do not wear loose-fitting clothing,
dangling drawstrings or items that could
become caught.
11. When starting the engine, pull cord slowly
until resistance is felt, then pull rapidly (if
not electric start).
12. Remove all external equipment/engine
loads before starting engine.
13. Direct coupled equipment components
such as, but not limited to blades,
impellers, pulleys, sprockets, etc., must be
securely attached.
4 Section 2 — important Safe operation practiceS
Maintenance & Storage
1. Keep the engine in safe working order
2. Allow the engine to cool at least five
minutes before storing. Never tamper
with safety devices. Check their proper
operation regularly.
3. Check bolts and screws for proper
tightness at frequent intervals to keep the
engine in safe working condition. Visually
inspect the engine for any damage.
4. Before cleaning, repairing or inspecting;
stop the engine and make certain all
moving parts have stopped. Disconnect
the spark plug wire and ground it against
the engine to prevent unintended
starting.
5. Do not change the engine governor
settings or over-speed the engine. The
governor controls the maximum safe
operating speed of the engine.
6. Maintain and replace safety and
instruction labels as necessary.
7. Always refer to the operator’s manual for
important details if the machine is to be
stored for an extended period of time.
8. If the fuel tank has to be drained, do this
outdoors.
9. Observe proper disposal laws and
regulations for gas, oil, etc. to protect the
environment.
Do not modify engine
To avoid serious injury or death, do not modify
engine in any way. Tampering with the governor
setting can lead to a runaway engine and cause
it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
Notice Regarding Emissions
Engines which are certified to comply with
California and federal EPA emission regulations
for SORE (Small Off Road Equipment) are
certified to operate on regular unleaded
gasoline, and may include the following
emission control systems: Engine Modification
(EM), Oxidizing Catalyst (OC), Secondary Air
Injection (SAI) and Three Way Catalyst (TWC) if
so equipped.
Safety Symbols
This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before
attempting to assemble and operate.
Symbol Description
READ THE OPERATOR’S MANUAL(S)
Read, understand, and follow all instructions in the manual(s) before attempting to assemble and
operate.
WARNING—GASOLINE IS FLAMMABLE
Allow the engine to cool at least two minutes before refueling.
WARNING— CARBON MONOXIDE
Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an
odorless and deadly gas.
WARNING— ELECTRICAL SHOCK
Do not use the engine’s electric starter in the rain.
WARNING— HOT SURFACE
Engine parts, especially the muffler, become extremely hot during operation. Allow engine and muffler
to cool before touching.
Spark Arrestor
WARNING!
This machine is equipped with an internal
combustion engine and should not be used on
or near any unimproved forest-covered, brush
covered or grass-covered land unless the engine’s
exhaust system is equipped with a spark arrestor
meeting applicable local or state laws (if any).
If a spark arrestor is used, it should be
maintained in effective working order by the
operator. In the State of California the above is
required by law (Section 4442 of the California
Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands.
A spark arrestor for the muffler is available
through your nearest engine authorized service
dealer or contact the service department, P.O.
Box 361131 Cleveland, Ohio 44136-0019.
WARNING! - SAVE THESE INSTRUCTIONS!
Your Responsibility — Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the
machine.
Set-Up
3
5
Oil & Fuel Specifications
IMPORTANT: The engine is shipped without
gasoline in the engine. See the following
instructions for adding gasoline.
IMPORTANT: Some engines are shipped with oil
already in the engine, others without oil already
in the engine. It is very important to check the
oil level before operating the engine and to
add oil if necessary. Running the engine with
insufficient oil can cause serious engine damage
and void the engine warranty
Oil Recommendations
Before starting engine, fill with engine oil,
capacity is 600 ml/20 oz. Refer to the viscosity
chart (“Figure 3-1) for oil recommendations.
Do not over-fill. Use a 4-stroke, or an equivalent
high detergent, premium quality engine oil
certified to meet or exceed U.S. automobile
manufacturer’s requirements for service
classification of a minimum level SJ (higher
letter ratings are acceptable such as SL and SM
grades).
Engine oil will display this designation on the
container.
NOTE: Do not use non-detergent oil or 2-stroke
engine oil. It could shorten the engine’s service
life.
Figure 3-1
Checking Oil Level
NOTE: Be sure to check the oil while on a level
surface with the engine stopped.
To avoid engine damage, it is important to:
Check oil level before each use
and every 5 operating hours when
engine is warm. Check oil level
more frequently during engine
break-in.
Keep oil level between “H” and “L
marks on dipstick. See “Figure 3-2”.
Be sure oil fill cap/plug is
tightened securely when checking.
1. Remove the oil filler cap/dipstick and
wipe the dipstick clean. See “Figure 3-2”.
2. Insert the cap/dipstick into the oil filler
neck, and tighten the cap until seated.
3. Remove the oil filler cap/dipstick. If the
level is low, slowly add oil until oil level
registers between high (H) and low (L),
“Figure 3-2”.
4. Replace and tighten cap/dipstick firmly
before starting engine.
NOTE: Do not overfill. Overfilling with oil may
cause smoking, hard starting, or spark plug
fouling.
NOTE: DO NOT allow oil level to fall below the
“L” mark on the dipstick. Doing so may result in
equipment malfunctions or damage.
NOTE: To change the oil on your engine, see the
Maintenance Section of this manual.
Fill
between
high (H)
and low (L)
marks
Figure 3-2
Filling Oil Sump
1. Be sure the engine is upright and level.
2. Remove the oil fill cap dipstick from oil
filler tube by rotating counter-clockwise
and lifting the dipstick out of the engine.
Wipe the dipstick clean with a shop rag.
3. Insert oil fill cap dipstick back into oil filler
tube. On quarter-turn oil fill caps, tighten
by rotating the cap clockwise until firmly
seated.
NOTE: Some units may have a threaded
dipstick. In this instance, insert the cap/
dipstick into the oil filler neck, but do not
screw it in to check.
4. Loosen and remove the oil fill cap
dipstick from the oil filler tube. Note the
oil level, if oil reading on the dipstick
is below the “L” mark, slowly add oil to
reach the “H” level. See “Figure 3-2”.
5. Insert oil fill cap dipstick back into oil
filler tube. Tighten by rotating the cap
clockwise until firmly seated.
6. Wipe away any spilled oil.
NOTE: To change the oil, see Checking and
Changing Oil instructions in the Maintenance
Section of this manual.
6 Section 3— Set-Up
Fuel Recommendations
CAUTION
Operating the engine with E15 or E85 fuel, an oil/
gasoline mixture, dirty gasoline, or gasoline
over 30 days old without fuel stabilizing
additive may result in damage to your engine’s
carburetor. Subsequent damage would not be
covered under the manufacturers warranty.
Use automotive gasoline (unleaded or low
leaded to minimize combustion chamber
deposits) with a minimum of 87 octane.
Gasoline with up to 10% ethanol (E10) or 15%
MTBE (Methyl Tertiary Butyl Ether) can be used.
Never use an oil/gasoline mixture or dirty
gasoline. Avoid getting dirt, dust, or water in the
fuel tank. DO NOT use E15 or E85 gasoline.
WARNING!
Gasoline is extremely flammable and is explosive
under certain conditions.
Refuel in a well-ventilated area with the
engine stopped. Do not smoke or allow
flames or sparks in the area where the
engine is refueled or where gasoline is
stored.
Do not overfill the fuel tank. After
refueling, make sure the tank cap is
closed properly and securely.
Be careful not to spill fuel when refueling.
Spilled fuel or fuel vapor may ignite. If
any fuel is spilled, make sure the area is
dry before starting the engine.
Avoid repeated or prolonged contact
with skin or breathing of vapor.
Adding Fuel
WARNING!
An adult should fuel this engine. NEVER allow
children to refuel the engine. Gasoline (fuel)
vapors are highly flammable and can explode.
Fuel vapors can spread and be ignited by a spark
or flame many feet away from engine. To prevent
injury or death from fuel fires, follow these
instructions:
DO NOT use leaded fuel.
Fuel must be fresh and clean. NEVER use
fuel left over from last season or stored for
long periods.
NEVER mix oil with fuel in this engine.
DO NOT use fuel containing Methanol
(Wood Alcohol).
1. Before refueling, allow the engine to cool
for two minutes.
2. Be sure engine is outdoors and in a well-
ventilated area.
3. Clean area around the fuel fill cap and
remove the fuel fill cap.
4. Using an approved red GASOLINE
container, add fuel slowly, being careful
to avoid spilling.
5. Replace the fuel cap and tighten securely.
Wipe up spilled fuel before starting
engine. If fuel is spilled DO NOT start
engine. Move machine away from area
of spillage. Avoid creating any source of
ignition until fuel vapors are gone.
6. Be sure fuel valve, if present, is open.
Electrical Power
WARNING!
DO NOT pull starter rope with engine running.
Doing so may VOID YOUR WARRANTY.
CAUTION
The extension cord can be any length, but must be
rated for 15 amps at 125 volts, grounded and rated
for outdoor use.
NOTES:
When connecting power cord always
connect power cord to switch box on engine
first; then into outlet. See “Figure 3-3”.
Determine what type of power source outlet
you will be connecting the power cord to,
before you start your engine. See Engines with
Electric Starters instructions in the Operation
Section of this manual.
Figure 3-3
Controls and Features
4
7
Throttle
The throttle control regulates the speed of the
engine and will shut off the engine when it is
moved into the stop position.
Choke
Activating the choke closes the choke plate on
the carburetor and aids in starting the engine.
Oil Drain
Removing the oil drain plug will drain the oil
from the engine.
Oil Filler Cap & Dipstick
Remove the oil cap to check the oil level and
add oil.
Fuel Fill
Remove the gas cap to add fuel.
Recoil Starter Handle
Pull the starter handle to start the engine.
Fuel Shut-Off Valve (If Equipped)
If equipped, is used for controlling the flow of
fuel between usage and transport/storage.
Electric Starter Inlet (If Equipped)
Requires the use of a three-prong outdoor
extension cord and a 120V power source/wall
outlet.
Electric Start Button (If Equipped)
Pressing the button on the top of the electric
starter switch engages the engine’s electric starter
when plugged into a 120V power source.
Primer Bulb (If Equipped)
Pressing the primer bulb forces fuel directly
into the engine’s carburetor to aid in starting a
“Cold” engine.
Key (If Equipped)
The key is a safety device. It must be fully inserted in
order for the engine to start. Remove the key when
the snow thrower is not in use.
Important: Do not turn the key in an attempt to
start the engine. Doing so may cause it to break.
Starter
Button
Electric
Starter Inlet
Oil Drain
Fuel Fill
Oil Filler Cap/
Dipstick
Choke
Primer
Bulb
Key
Throttle
Throttle
Air Filter
Choke
Fuel Shut-off
Valve
Recoil Starter
Handle
Oil Drain
Muffler
Fuel Fill
Oil Filler Cap/
Dipstick
Fuel Fill
Starter
Button
Electric
Starter Inlet
Oil Drain
Oil Filler Cap/
Dipstick
Primer
Bulb
Key
Throttle
Choke
Recoil Starter Handle
Muffler
Electric
Starter
Inlet
Starter
Button
Recoil
Starter
Handle
Choke
Muffler
Oil Filler Cap/
Dipstick
Oil Drain
Figure 4-1
Operation
5
8
Pre-Operation Check
IMPORTANT: The engine is shipped without
gasoline in the engine. See the Set-Up Section
of this manual for instructions on adding
gasoline.
IMPORTANT: Some engines are shipped with oil
already in the engine, others without oil already
in the engine. It is very important to check the
oil before operating the engine and to add if
necessary. See the Set-Up Section of this manual
for instructions on checking and adding oil.
For your safety, and in order to maximize
the service life of this equipment, it is very
important to check its condition before you
operate this engine. Make certain to service,
correct or fix any problem that might be
identified before attempting to operate this
engine.
WARNING!
Improperly maintaining this engine, or failure to
correct any problem before operation can cause a
malfunction which could result in serious injury or
even death.
Always perform a pre-operation inspection before
each operation, and correct any problem.
Before you start the engine, always check the
following items:
1. Fuel Recommendations (See Set Up
Section)
2. Checking Oil Level (See Set Up Section)
3. Air filter (if equipped) (See Maintenance
Section)
4. General Overall Inspection. Check for any
fluid leaks or discharges, and loose or
damaged parts.
5. Check the owner’s manual provided with
the equipment that is powered by this
engine. Review the owner’s manual for
any precautions and procedures that
should be followed before starting the
engine.
Starting the Engine
WARNING!
Always keep hands and feet clear of moving parts.
Do not use a pressurized starting fluid. Vapors are
flammable.
WARNING!
An adult should start the engine. Only allow
children to start the engine if an adult has
determined they are experienced and capable of
such operation.
WARNING!
If you are unable to start this engine after
following instructions in this manual, contact your
authorized MTD Service Dealer. To avoid serious
burn injuries or damage to your engine, DO NOT
attempt to start or troubleshoot this engine in any
other way. for example:
DO NOT use starting fluid.
DO NOT spray flammable vapors into the
carburetor.
DO NOT put flammable liquids into
carburetor.
DO NOT operate engine or pull on starter
rope with spark plug removed. Fuel can
spray from spark plug hole and ignite.
NOTE: Allow the engine to warm up for a few
minutes after starting. The engine will not
develop full power until it reaches operating
temperatures.
Familiarize
yourself with the engine symbols
shown in “Figure 5-1” before attempting to
start this engine. If this engine is remotely
controlled by the equipment it is powering, be
sure to familiarize yourself with the equipment
Operator’s Manual as well.
Fast
Run
Slow/Idle
Choke
Engine Off
Primer
Figure 5-1
1. If equipped, insert the key.
Important: The key is a safety device. Do not
turn the key in an attempt to start the engine.
Doing so may cause it to break.
Key
Figure 5-2
NOTE: The following starting instructions are
for several different types of engines. In order
to locate the instructions that apply to your
engine, first determine what type of starter you
have. If you have an electric starter, see Engines
With Electric Starters. If you have a manual
recoil starter, see Engines with Recoil Starters
later in this section.
Pull StartElectric Start
Figure 5-3
9Section 5 — operation
Engines With Electric
Starters
If you have a manual recoil starter,
see Engines with Recoil Starters
later in this section.
WARNING!
DO NOT pull the starter handle while the engine is
running.
WARNING!
The electric starter is equipped with a 120V A.C.
Power Plug designed to operated with a grounded
extension cord and on 120V A.C. household
current. It must be properly grounded at all times
to avoid the possibility of injury or death from
electrical shock.
a. Determine if your house wiring has a
Ground Fault Interrupted (G.F.I.) Three-Wire
Grounded System; if you are not sure, ask a
Licensed Electrician.
b. If your house wiring does not have a G.F.I.
Three-Wire Grounded System, DO NOT
USE THIS ELECTRIC STARTER UNDER ANY
CONDITION.
c. If your house wiring is grounded and a
G.F.I. three-Prong Wall Receptacle is not
available at the location where your starter
will be used, one must be installed by a
Licensed Electrician BEFORE USING THE
ELECTRIC STARTER!
1. To avoid carbon monoxide poisoning,
be sure engine is outdoors in a well-
ventilated area.
2. Be sure fuel valve, if present (see
equipment Operator’s Manual
instructions) is open and all switches are
on.
3. Plug an extension cord into the outlet
located on the engine’s surface. Plug the
other end of extension cord into a three-
prong 120-volt, grounded, AC outlet in a
well-ventilated area.
CAUTION
The extension cord can be any length, but must be
rated for 15 amps at 125 volts, grounded and rated
for outdoor use.
IMPORTANT: When connecting the
power cord, always connect the power
cord to the switch box on the engine first;
then into the outlet.
4. Move engine speed control, if equipped,
in the “Fast” position.
5. If equipped, set the choke control to
“FULL CHOKE” position.
6. If equipped, Prime 3 - 5 times.
Make sure you cover the vent hole
with your thumb.
Hold the primer bulb in for one full
second each time you press it.
NOTE: DO NOT use the primer bulb
to restart a warm engine after a short
shutdown. Doing so will flood the
engine and may result in equipment
malfunction.
NOTE: If restarting a warm engine after a
short shutdown, move the engine speed
control (if equipped) the “FAST” position
and move the choke control to the “NO
CHOKE” position.
7. Push the starter button to start the
engine.
IMPORTANT: DO NOT operate an electric
starter for more than 5 seconds during
each attempt.
8. Release the starter button.
NOTE: If the engine fails to start after 3
attempts, repeat steps 6 through 7.
9. After the engine starts:
Move the choke control to 1/2
“CHOKE” position until the engine
runs smoothly.
Next, move the choke control to
the NO CHOKE position.
NOTE: If the engine starts but falters when the
choke control is moved to the “NO CHOKE”
position. Perform the following:
Momentarily move choke control
back to “FULL CHOKE” position.
Next, move the choke control to
“1/2 CHOKE” position until engine
runs smoothly.
Finally, move the choke control to
the NO CHOKE position.
NOTE: If the engine stops with the choke control
in the “NO CHOKE” position, repeat steps 6-9 to
restart the engine.
NOTE: If the engine fails to start after 3 attempts
in the “NO CHOKE” position, move the choke
control to “FULL CHOKE” position and repeat
steps 6-9 to restart the engine.
10. Disconnect the extension cord form the
outlet.
11. Disconnect the extension cord form the
switch box on the engine.
IMPORTANT: If engine does not start after
following steps 1 through 11, contact your
Authorized MTD Service Dealer. DO NOT
attempt to troubleshoot this engine in any
other way.
Engines with Recoil
Starters
If you have an electric starter,
see Engines with Electric
Starters earlier in this section.
WARNING!
DO NOT pull starter rope with engine running.
Doing so may VOID YOUR WARRANTY.
1. To avoid carbon monoxide poisoning,
be sure engine is outdoors in a well-
ventilated area.
2. Be sure fuel valve, if present (see
equipment Operator’s Manual
instructions) is open and all switches are
on.
3. Move the engine speed control, if
equipped, to the “FAST” position.
4. If equipped, set the choke control to
“FULL CHOKE” position.
5. If equipped, Prime 3 - 5 times.
Make sure you cover the vent hole
with your thumb.
Hold the primer bulb in for one full
second each time you press it.
NOTE: DO NOT use the primer bulb
to restart a warm engine after a short
shutdown. Doing so will flood the
engine and may result in equipment
malfunction.
NOTE: If restarting a warm engine after a
short shutdown, move the engine speed
control (if equipped) the “FAST” position
and move the choke control to the “NO
CHOKE” position.
WARNING!
When pulling the starter rope, the rope can
unexpectedly jerk back toward the engine causing
serious injury. To avoid this risk, carefully follow
these instructions:
6. Grasp the starter cord handle.
Pull rope out slowly until you feel
resistance.
Allow the rope to retract, then pull
the rope with one rapid full arm
stroke.
Return the rope slowly to the
original position.
NOTE: Following the instructions listed in
the steps above avoids potential damage
to the recoil mechanism.
10 Section 5— operation
NOTE: If the recoil starter handle is frozen
and will not operate the engine, proceed
as follows:
Pull as much rope out of the
starter as possible.
Release the starer handle and let
it snap back against the starter
to break up ice; these two steps
should only be done when the
starter is frozen.
7. If the engine fails to start after 3 attempts
repeat steps 5 through 6 and try again.
8. When the engine starts:
Move the choke control to 1/2
“CHOKE” position until the engine
runs smoothly.
Next, move the choke control to
the NO CHOKE position.
NOTE: If the engine starts but falters when the
choke control is moved to the “NO CHOKE”
position:
Momentarily move choke control
back to “FULL CHOKE” position.
Next, move the choke control to
“1/2 CHOKE” position until engine
runs smoothly.
Finally, move the choke control to
the NO CHOKE position.
NOTE: If the engine stops with the choke control
in the “NO CHOKE” position, repeat steps 5-8 to
restart the engine.
NOTE: If the engine fails to start after 3 attempts
in the “NO CHOKE” position, move the choke
control to “FULL CHOKE” position and repeat
steps 5-8 to restart the engine.
IMPORTANT: If engine does not start after
following steps 1 through 8, contact your
Authorized MTD Service Dealer. DO NOT
attempt to troubleshoot this engine in any
other way.
Stopping the Engine & Short
Term Storage
Stop engine in accordance with the equipment
Operator’s Manual.
WARNING!
To avoid unsupervised engine operation, especially
by children, NEVER leave the engine unattended
while running. Always turn off the engine after
use and remove the ignition key, if equipped.
WARNING!
NEVER store the engine with fuel in the fuel tank
inside a building with potential sources of ignition
such as hot water tank and space heaters, clothes
drivers, electric motors, etc.
Stopping The Engine
1. If operating the engine in the snow or
rain, run the engine for a few minutes to
help dry off any moisture.
2. Move the equipment control, if present
(see Equipment Owner’s Manual), engine
control lever or ignition switch to “STOP
or “OFF” position.
3. Remove ignition key, if provided (see
equipment Operator’s Manual).
NOTE: Removing the key will reduce the
possibility of unauthorized starting of the
engine while equipment is not in use.
WARNING!
NEVER store the engine with fuel in the fuel tank
inside a building with potential sources of ignition
such as hot water tank and space heaters, clothes
dryers, electric motors, etc.
After the Engine is Stopped
WARNING!
To prevent the possible freeze-up of engine
controls, follow instructions with engine STOPPED,
listed below:
1. Wipe all snow and moisture from the
engine control lever and choke areas.
2. Move the equipment control, if present,
(see equipment Operator’s Manual),
engine control lever or ignition switch
back and forth several times and leave
the control in the “STOP” or “OFF”
position.
3. Move the engine choke back and forth
several times and leave in the “FULL
CHOKE” position.
4. Be sure the Fuel Shut-Off Valve, if present,
is off.
Maintenance
6
11
Maintenance Schedule
After First
5 Hours
Each use
or Every
5 Hrs.
Every
Season or
25 Hours
Every
season or
50 Hours
Every
season or
100 Hours
Service
Dates
Check Engine Oil Level
P
Change Engine Oil
P P
Check Air Cleaner (If so equipped)
P
Service Air Cleaner (If so equipped)
P
Check Spark Plug
P
Replace Spark Plug
P
Clean Engine Shroud (If so equipped)
P
Clean around muffler
P
Replace Fuel Filter (If equipped)
P
Periodic inspection and adjustment of the
engine is essential if high level performance
is to be maintained. Regular maintenance will
also ensure a long service life. The required
service intervals and the kind of maintenance
to be performed are described in the table
above. Follow the hourly or calendar intervals,
whichever occur first. More frequent service is
required when operating in adverse conditions.
WARNING!
Shut off the engine before performing any
maintenance. To prevent accidental start-up,
disconnect the spark plug boot.
NOTE:
If engine must be tipped to transport
equipment or to inspect or remove grass, keep
spark plug side of engine up. Transporting or
tipping engine spark plug down may cause
smoking, hard starting, spark plug fouling, or oil
saturation of air cleaner.
WARNING!
If the engine has been running, the muffler will be
very hot. Be careful not to touch the muffler.
Oil Recommendations
Refer to the viscosity chart (“Figure 6-1) for
oil recommendations. Do not over-fill. Use
a 4-stroke, or an equivalent high detergent,
premium quality engine oil certified to meet
or exceed U.S. automobile manufacturer’s
requirements for service classification of a
minimum level SF or SG (higher letter ratings
are acceptable such as SJ, SL and SM grades).
Engine oil will display this designation on the
container.
NOTE: Do not use non-detergent oil or
2-stroke engine oil. It could shorten the
engine’s service life.
Figure 6-1
Checking and Changing the Oil
To avoid engine damage, it is important to:
Check oil level before each use and every
5 operating hours when the engine is
warm.
Change the oil after the first 5 operating
hours and every 50 operating hours
thereafter. Engine should still be warm
but NOT hot from recent use.
Oil Fill Cap and Dipstick
WARNING!
Before tipping engine or equipment to drain oil,
drain fuel from tank by running engine until fuel
tank is empty.
1. Carefully disconnect the spark plug
wire and keep it away from the spark
plug. Refer to “Figure 6-2” for spark plug
location.
Keep the disconnected spark plug
wire securely away from the metal
parts where arcing could occur.
Carefully attach the spark plug
wire to the grounding post, if
provided.
Spark
Plug
Spark
Plug
Boot
Figure 6-2
12 Section 6 — Maintenance
2. Be sure that the fuel fill cap is on and
securely tightened.
3. Be sure to find correct oil drain plug
location, if present (see the equipment
Operator’s Manual instructions for
additional information).
4. Clean area around the oil drain plug.
5. Place an approved recyclable oil
container under the oil drain plug.
6. Remove the Oil drain plug. See “Figure
6-3”.
NOTE: Depending on which engine
model you have, the oil plug may be
positioned differently. These positions
include on the front and/or rear side
of the block, or as an extended tube.
Examples are shown in “Figure 6-3”.
Oil
Drain
Figure 6-3
WARNING!
Used engine oil may cause skin cancer if repeatedly
left in contact with the skin for prolonged periods.
Although this is unlikely unless you handle used oil
on a daily basis, it is still advisable to thoroughly
wash your hands with soap and water as soon as
possible after handling used oil.
7. Tip engine to position the oil flow, so it
will drain from the lowest point on the
engine.
8. Drain the oil into an approved recyclable
oil container.
NOTE: Please dispose of used engine oil
in a manner that is compatible with the
environment. We suggest you take it in
a sealed container to your local service
station for reclamation. Do not throw it in
the trash or pour it on the ground.
9. Install the oil drain plug and tighten
securely.
10. Clean area around the oil drain plug.
11. Remove the oil fill cap dipstick.
12. Fill with the recommended Oil. See
Figure 6-1”.
NOTE: DO NOT overfill oil filler. Doing
so may result in oil carry-over to the
equipment and cause malfunction or
damage.
NOTE: DO NOT allow oil level to fall
below and “L” mark on dipstick. Doing so
may result in equipment malfunction or
damage.
13. Wipe away any spilled oil.
14. Check the oil level by installing the Oil Fill
Cap/Dipstick.
For threaded Oil Fill Cap/Dipstick
models, rest the cap on the
threads, do not tighten down the
cap to check the oil level.
For quarter-turn Oil Fill Cap/
Dipstick models, tighten down the
cap to check the oil level.
NOTE: See the Set-Up section earlier in
this manual for detailed instructions on
identifying and checking the oil on each
of these specific engine models.
15. Remove the oil filler cap/dipstick. If the
level is low, slowly add oil until oil level
registers between high (H) and low (L),
“Figure 3-2” in the Set-Up section.
16. Repeat Steps 14 & 15 to be sure that the
correct oil level has been achieved.
17. Once the proper oil level has been
confirmed, install the Oil Fill Cap/Dipstick.
Tighten securely
18. Carefully disconnect spark plug wire from
grounding post, if present.
19. Carefully reconnect the spark plug wire
to the spark plug.
NOTE: It is advisable to recheck the oil level
after you have operated the engine for a
short while, and the normal engine operating
temperature has been achieved.
WARNING!
If the engine has been running, the muffler,
engine head and spark plug will be very hot. Be
careful not to touch any of these components until
they have cooled.
Spark Plug Service
WARNING!
DO NOT check for spark with spark plug removed.
DO NOT crank engine with spark plug removed.
Check the spark plug yearly or every 100
operating hours. To ensure proper engine
operation, the spark plug must be properly
gapped and free of deposits.
1. Remove the spark plug boot. See
Figure 6-2”.
2. Clean the area around the spark plug.
3. Use a spark plug wrench to remove
the plug.
WARNING!
If the engine has been running, the muffler,
engine head and spark plug will be very hot. Be
careful not to touch any of these components until
they have cooled.
4. Visually inspect the spark plug. Discard
the spark plug if there is apparent wear,
or if the insulator is cracked or chipped.
Replace the plug if the electrodes are
pitted, burned or fouled with deposits.
5. Clean the spark plug with a wire brush if it
is to be reused.
6. Measure the plug gap with a feeler
gauge. Correct as necessary by bending
side electrode. See “Figure 6-4”. The gap
should be set to 0.030 in. (0.76mm).
7. Check that the spark plug washer is in
good condition
8. Thread the spark plug in by hand to
prevent cross-threading.
9. After the spark plug is seated, tighten
with a spark plug wrench to compress the
washer.
NOTE: When installing a new spark
plug, tighten  turn after the spark plug
seats to compress the washer. When
reinstalling a used spark plug, tighten
- turn after the spark plug seats to
compress the washer.
NOTE: The spark plug must be securely
tightened. An improperly tightened
spark plug can become very hot and may
damage the engine.
Electrode
0.06-0.03 in.
0.60-0.80 mm
Figure 6-4
Air Filter
NOTE: Not all engines have air filters, such as
engines used for snow throwers. Service the air
filter if one is present.
Paper filters cannot be cleaned and must be
replaced once a year or every 100 operating
hours; more often if used in extremely dusty
conditions.
WARNING!
Never use gasoline or low flash point solvents
for cleaning the air cleaner element. A fire or
explosion could result.
13Section 6 — Maintenance
NOTE: Never run the engines that have air filters
without them. Rapid engine wear can result.
1. Press the tab on the air filter cover and lift
the cover, or un-thread the thumbscrew,
depending on the model of engine you
have. See “Figure 6-5”.
Figure 6-5
2. Replace paper element when dirty or
damaged. Clean foam element or replace
when damaged.
3. To clean foam element, separate it
from the paper element and wash in
liquid detergent and water. Allow to dry
thoroughly before using. Do not oil the
foam element.
Adjustments
DO NOT make any engine adjustments. Factory
settings are satisfactory for most conditions.
If adjustments are needed, contact your
Authorized MTD Servicing Dealer.
Carburetor
If you think you carburetor needs adjusting, see
your nearest Authorized MTD Servicing Dealer.
Engine performance should NOT be affected
at altitudes up to 7,000 feet (2,134 meters). For
operation at higher elevations, contact your
Authorized MTD Servicing Dealer.
Alternator (if equipped)
Contact your Authorized MTD Servicing Dealer
for alternator related electrical problems such
as:
Inoperative Starter
Discharged Battery
Fuse Replacement
Alternator Maintenance/Repairs
Engine Speed
WARNING!
To avoid serious injury or death, DO NOT modify
engine in any way. Tampering with the governor
setting can lead to a runaway engine and cause it
to operate at unsafe speeds. NEVER tamper with
the factory setting of the engine governor.
WARNING!
Running the engine faster than the speed set at
the factory can be dangerous and will VOID THE
ENGINE WARRANTY.
Removing Snow from the Engine
After each use, remove snow from the following
areas:
Oil Fill Cap Dipstick
Fuel Fill Cap
Recoil Starter/Flywheel Screen
Linkage
Guards
Spark Plug Connection (if visible).
Electric Starter Switch Box, if present
(see the equipment Operator’s Manual
instructions).
NOTE: See the equipment Operator’s
Manual instructions for proper location of
fuel fill cap and control lever.
1. Removing snow will ease operation of the
recoil starter rope and reduce the risk of
water contamination when opening the
fuel fill cap.
NOTE: For more information about recoil
starters, see Engine’s with Recoil Starters
in the Operation Section of this manual.
Transporting Your Engine
WARNING!
NEVER transport this engine inside of another
vehicle or in any enclosed space if there is any
gasoline in the tank. Fuel vapor or spilled fuel may
ignite.
WARNING!
If there is fuel in the fuel tank, close the fuel valve,
if equipped, and transport the engine upright in
an open vehicle, such as an open trailer or open
bed of a pickup truck.
If you DO NOT have an open vehicle and have to
transport the engine upright in a closed vehicle,
follow these steps for emptying the fuel tank
before transporting:
1. Empty fuel tank by using a commercially
available suction device designed for use
with gasoline.
WARNING!
DO NOT pour fuel from the engine or siphon fuel
by mouth.
2. Drain fuel into an approved red gasoline
container, being careful to avoid spilling.
3. Run the engine until remaining fuel is
consumed.
WARNING!
NEVER leave the engine unattended when it is
running and NEVER run the engine in an enclosed
area.
Storing Your Engine
Short-Term/Seasonal Storage
Clean Engine
If the engine has been running, allow it to cool
for at least half an hour before cleaning.
Before servicing the engine, remove the
carburetor cover and/or blower housing.
Discard the dirt and debris from the following
areas:
Cooling Fins
Air Intake Screen or Recoil Starter/
Flywheel Guard Areas
Spark Plug Connection
Levers
Linkage Area
Guards
Carburetor
Head
Removing debris will insure adequate cooling,
correct engine speed and reduce the risk of fire.
NOTE: Do not spray engine with water to clean
because water could contaminate fuel. Using
a garden hose or pressure washing equipment
can also force water into the air cleaner or
muffler opening. Water in the air cleaner will
soak the paper element, and water that passes
through the element or muffler can enter the
cylinder, causing damage.
WARNING!
Accumulation of debris around muffler could cause
a fire. Inspect and clean before every use.
14 Section 6 — Maintenance
Fuel Storage
WARNING!
NEVER store engine with fuel in the fuel tank
inside a building with potential sources of ignition
such as hot water heater, space heater, clothes
dryer, electric motor, etc. Failure to do so may
result in an explosion and result in death or serious
injury.
NOTE: If engine fuel stored in the gas tank and/
or an approved gas container is to be unused
without gasoline stabilizer for more than 15-30
days, prepare it for short-term/seasonal storage.
See Fuel Treatment later in this section.
NOTE: If engine fuel is to be stored for more
than one season, without gasoline stabilizer, it
will gradually deteriorate. Also, if it is stored in
the engine’s gas tank without gasoline stabilizer
it is likely that your carburetor will have gum
deposits, a clogged fuel system and will VOID
YOUR WARRANTY. Prepare the fuel for extended
storage.
Fuel System
To avoid stale fuel and carburetor problems,
treat the fuel system in the following manner:
NOTE: Always follow mix ratio found on the
stabilizer container. Failure to do so may result
in equipment damage.
NOTE: It is NOT necessary to drain stabilized gas
from carburetor.
Fuel Treatment
1. Add a gasoline stabilizer according to the
manufacturer’s instructions.
2. Run engine at least 10 minutes after
adding the stabilizer to allow it to reach
the carburetor.
WARNING!
NEVER store the engine with the fuel in the fuel
tank inside a building with potential sources of
ignition such as a hot water heater, space heater,
clothes dryer, electric motor, etc.
NOTE: Instead of using a fuel preservative/
stabilizer, you can empty the fuel tank as
described in Extended Storage — Draining the
Fuel.
Extended Storage
Draining the Fuel
NOTE: Clean debris from the engine before
draining fuel from the carburetor.
NOTE: If you have prepared your fuel for short-
term storage it is NOT necessary to drain fuel
that contains stabilizer from your carburetor.
WARNING!
To avoid severe injury or death, DO NOT pour fuel
from engine or siphon fuel by mouth.
1. To prevent serious injury from fuel fires,
empty fuel tank by running engine until
it stops from lack of fuel. DO NOT attempt
to pour fuel from engine.
2. Run the engine while waiting until the
remaining fuel is consumed.
WARNING!
NEVER leave the engine unattended when it is
running and NEVER run the engine in an enclosed
area.
3. Begin servicing the cylinder bore as per
the following instructions.
Oil Cylinder Bore
WARNING!
When lubricating cylinder bore, fuel may spray
from the spark plug hole. To prevent serious injury
from fuel fires, follow these instructions:
1. Turn off all the engine switches.
2. Remove the ignition key, if provided.
3. Carefully disconnect the spark plug wire
and keep it away from the spark plug.
Keep the disconnected spark plug
wire securely away from the metal
parts where arcing could occur.
Carefully attach the spark plug
wire to the grounding post, if
provided.
4. Remove the spark plug.
5. Squirt  oz. (15ml) of clean engine oil
into the spark plug hole.
6. Cover the spark plug hole with a rag to
prevent fuel from spraying from the spark
plug hole when the starter rope is pulled.
NOTE: for engines equipped with a recoil
starter, proceed to Step 7. For engines equipped
with electric starters, proceed to Step 8.
7. For Recoil starter engines:
Grasp the starter cord handle.
Pull the starter cord handle out
slowly using a full arm stroke.
Repeat once. This will distribute
the oil throughout the cylinder to
prevent corrosion during storage.
Proceed to Step 9.
8. For electric starter engines:
Plug an extension cord into the
three-prong connector located
on the engine’s surface. Plug the
other end of extension cord into a
three-prong 120-volt, grounded,
AC outlet in a well-ventilated area.
Push and immediately release the
starter button. This will distribute
the oil throughout the cylinder to
prevent corrosion during storage.
Disconnect the extension cord
form the outlet.
Disconnect the extension cord
form the three-prong connector
on the engine.
Proceed to Step 9.
9. Remove the rag from spark plug hole.
10. Install the spark plug.
11. Carefully disconnect the spark plug wire
from the grounding post, if provided.
12. Connect the spark plug wire plug wire to
the spark plug.
Oil
Change the oil if NOT changed within the last
3 months. See Checking and Changing the Oil
earlier in this section.
Off-Season Storage
CAUTION
Failure to use a fuel stabilizing additive or
completely run the engine until it’s out of fuel
before off-season storage may result in damage
to your engine’s carburetor. Subsequent damage
would not be covered under the manufacturers
warranty.
Engines stored between 30 and 90 days need to
be treated with a gasoline stabilizer and engines
stored over 90 days need to be drained of fuel
to prevent deterioration and gum from forming
in fuel system or on essential carburetor parts. If
the gasoline in your engine deteriorates during
storage, you may need to have the carburetor,
and other fuel system components, serviced or
replaced.
1. Remove all fuel from tank by running
engine until it stops from lack of fuel.
WARNING!
Never leave engine unattended while it is running.
2. Change the oil. See Changing the Oil
earlier in this section.
3. Oil the cylinder bore. See Oil Cylinder
Bore earlier in this section.
4. Clean debris from around the engine
and the muffler. Touch up any damaged
paint, and coat other areas that may rust
with a light film of oil.
5. Store in a clean, dry and well ventilated
area away from any appliance that
operates with a flame or pilot light, such
as a furnace, water heater, or clothes
dryer. Also avoid any area with a spark
producing electric motor, or where power
tools are operated.
6. If possible, also avoid storage areas with
high humidity, because that promotes
rust and corrosion.
7. Keep the engine level in storage. Tilting
can cause fuel or oil leakage.
Troubleshooting
7
15
Problem Cause Remedy
Engine Fails to start 1. Engine flooded
2. Spark plug wire disconnected
3. Fuel tank empty
4. Stale fuel
5. Engine not choked
6. Faulty spark plug
7. Throttle in stop position
1. Wait at least 10 minutes before starting
2. Connect wire to spark plug
3. Fill tank with clean, fresh fuel
4. Drain fuel tank. Refill with fresh fuel
5. Choke engine
6. Clean, adjust gap or replace
7. Move throttle to FAST/Run position
Engine runs erratically 1. Spark plug wire loose
2. Spark plug scorched, defective or electrode gap is
set incorrectly
3. Stale fuel
4. Engine running with choke on
5. Water or dirt in fuel system
1. Connect and tighten spark plug wire
2. Re-adjust electrode gap or change
3. Drain fuel tank. Refill with fresh fuel
4. Move choke to off
5. Drain fuel tank. Refill with fresh fuel
Engine overheats 1. Engine oil level low 1. Fill engine with proper amount of engine oil
Replacement Parts
8
16
Phone (800) 800-7310 or (330) 220-4683 to order replacement parts or a complete Parts Manual (have your full model number and
serial number ready). Parts Manual downloads are also available free of charge at www.mtdproducts.com.
Component Part Number and Description
951-10292 Spark Plug
951-17331 Air Cleaner (Log Spiltters
Tillers, Chipper/Shredders)
951-14262 Air Cleaner (Log Spiltters
Tillers, Chipper/Shredders)
951-15172 Fuel Cap Assembly
(2, 3 Stage Snow Throwers)
751-10487C Fuel Cap Assembly
(Single-stage Snowthrowers)
951-12535 Fuel Cap Assembly
(Tillers, Chipper/Shredders
and Log Splitters)
731-05632 Key (Two-stage Snow Throwers)
Notes
9
17
18 Section 11— noteS
MTD LLC. APARTADO POSTAL 361131 CLEVELAND, OHIO 44136-0019
Medidas importantes de seguridad • Configuración • Funcionamiento • Mantenimiento
• Solución de problemas • Garantía
ADVERTENCIA
LEA Y RESPETE TODAS LAS NORMAS DE SEGURIDAD E INSTRUCCIONES INCLUIDAS EN ESTE
MANUAL ANTES DE PONER EN FUNCIONAMIENTO ESTA MÁQUINA.
SI NO RESPETA ESTAS INSTRUCCIONES PUEDE PROVOCAR LESIONES PERSONALES.
Manual del OperadOr
Motor de 179cc, 208cc, 243cc & 272cc Eje Horizontal
Este Manual del Operador es una parte importante de su nuevo motor. Le ayudará a preparar y mantener la unidad para obtener los
mejores resultados. Antes de operar el motor lea cuidadosamente y comprenda todo el manual.
Gracias
Asistencia al Cliente
Por favor, NO devuelva la máquina al minorista o distribuidor sin ponerse en contacto primero con el Departamento de
Asistencia al Cliente.
En caso de tener problemas con este producto o de tener dudas con respecto a los controles, funcionamiento o
mantenimiento de este motor, puede solicitar la ayuda de expertos. Elija entre las opciones que se presentan a continuación:
Visite nuestro sitio web en www.mtdproducts.com
Llame a un representante de Asistencia al Cliente al (800) 800-7310 ó (330) 220-4683
Escríbanos a MTD LLC • P.O. Box 361131 • Cleveland, OH • 44136-0019
NúMero de Modelo / NúMero de Serie
/
Registro de información de producto
Antes de operar su motor nuevo, por favor localice su placa de
modelo y registre la información en el área situada a la derecha. Si
tiene que solicitar soporte técnico a través de nuestro sitio web o
de un distribuidor de servicio local, necesitará esta información.
Al propietario
1
2
Medidas importantes de seguridad .................... 23
Símbolos De Seguridad ........................................ 24
Montaje y configuración ...................................... 25
Controles y Características ................................... 27
Funcionamiento .................................................... 28
Mantenimiento .......................................................31
Solución de problemas ......................................... 36
Piezas De Repuesto ............................................... 37
Declaración de Emisiones/Garantía ......Consulte el
suplemento que se adjunta por separado
Índice
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Cub Cadet 1X 21" LHP User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages