– 1 –
Please read the operating instructions for further details.
Controls
Handset
A Speaker
B Charge contact
C {j/OK} (Menu/OK)
D {k} (Phonebook)
E {C} (Talk)
F Navigator key
L {e}{v}: To search for the desired item in
menus.
L{>}: To select the desired item or move
the cursor to the right.
L{<}: To return to the previous screen or
move the cursor to the left.
G {s} (Speakerphone)
H {R} (Recall)
I Receiver
J Display
K {R} (Redial/Pause)
L {ih} (Off/Power)
M {C/T} (Clear/Mute)
N Dial keypad
L The icons printed below the dial keys
shown in the illustration (g, d, ■ etc.) are
found on the KX-TCD220 only. These
icons indicate answering system
operations.
O {INT} (Intercom)
P Microphone
*The pictured model is KX-TCD220.
C
s
h
T
H
G
g
L
N
g
d
n
n
i
N
a
O
P
C
E
F
G
H
D
L
I
M
B
A
J
K
N
Digital Cordless Phone
Model No. KX-TCD210FX
Digital Cordless Answering System
Model No. KX-TCD220FX
Quick Guide
TCD210_220FX_QG(e).fm Page 1 Wednesday, January 5, 2005 11:07 AM
– 2 –
Base unit
Displays
Display icons
Various icons appear on the handset display to indicate the current status of the unit.
A Answer on indicator (KX-TCD220 only)
B {x} (Page)
C Charge contact
*The pictured model is KX-TCD220.
A
bB
C
w Within range of a base unit
L When flashing: Handset is
searching for base unit. (out
of range of base unit,
handset is not registered to
base unit, no power on base
unit)
L Handset is accessing base
unit. (intercom, paging,
changing base unit settings,
etc.)
k Handset is on an outside call.
o Call bar is on.
u Answering system is on. (KX-
TCD220 only)
5 Battery strength
[VE] Voice enhancer is set to high
or low tone.
[N] Night mode is on.
[X] Key lock is on.
[2] Handset number: The left icon
shows handset 2 example.
-2- Base unit number: The left
icon shows base unit 2
example.
F New SMS message received
(SMS users only)
[IN USE] Line is being used by another
handset.
TCD210_220FX_QG(e).fm Page 2 Wednesday, January 5, 2005 11:07 AM
– 3 –
Connections
When the AC adaptor is connected, a short beep will be heard. If it is not heard, check the
connections.
Battery installation
Insert the batteries negative (T) terminal first. Close the handset cover. Place the handset
on the base unit for about 7 hours before initial use.
*The pictured model is KX-TCD210.
Note:
L Use only rechargeable batteries.
Important:
L Use only the AC adaptor and telephone
line cord supplied with this unit.
Note:
L Never install telephone wiring during a
lightning storm.
L The AC adaptor must remain connected
at all times. (It is normal for the adaptor to
feel warm during use.)
(220–240 V, 50 Hz)
To telephone
network
Hooks
TCD210_220FX_QG(e).fm Page 3 Wednesday, January 5, 2005 11:07 AM
– 4 –
Turning the power on
Press {ih} for about 1 second.
Setting the date and time
1
Press {j/OK}.
2 Select “Handset Setup”, then press {>}.
3 Select “Time Settings”, then press {>}.
4 Select “Set Date & Time”, then press {>}.
5 Enter the current day, month and year by selecting 2 digits for each.
6 Enter the current hour and minute by selecting 2 digits for each.
L You can select “AM”, “PM” or 24-hour time entry by pressing {*} repeatedly.
7 Press {j/OK}.
8 Press {ih}.
Basic operations
Feature Operation
To turn the power off Press {ih} for about 2 seconds.
To make a call Dial the phone number, then press {C}.
To turn on the speakerphone Press {s}.
To hang up Press {ih}.
To adjust the receiver or speaker
volume
Press {e} or {v} while talking.
To redial the last number dialled Press {R}, then press {C}.
To make a call using the redial list Press {R}. Press {e} or {v} repeatedly to
select the desired number, then press {C}.
To answer a call Press {C}.
To mute your voice during a call Press {C/T}. To return to the conversation, press
{C/T} again.
To store a name and phone number
in the handset phonebook
Press {k}, {j/OK}, select “New Entry”, then
press {>}.
Enter the party’s name (16 characters max.), then
press {j/OK}. Enter the party’s phone number
(24 digits max.), then press {j/OK}. Select the
desired category for the entry, then press {>}.
Select “Save”, then press {>}. Press {ih}.
L To enter a name, see the character table in the
operating instructions.
TCD210_220FX_QG(e).fm Page 4 Wednesday, January 5, 2005 11:07 AM
– 5 –
Answering system (KX-TCD220 only)
To make a call using the handset
phonebook
Press {k}. Press {e} or {v} repeatedly to
display the desired entry, then press {C}.
To adjust the handset ringer volume Press {j/OK}. Select “Handset Setup”, then
press {>}. Select “Ringer Setup”, then press
{>}. Select “Ringer Volume”, then press {>}.
Press {e} or {v} repeatedly to select the desired
volume. Press {>}, then press {ih}.
To change the ringtone used by the
handset for outside calls
Press {j/OK}. Select “Handset Setup”, then
press {>}. Select “Ringer Setup”, then press
{>}. Select “Ext. Ringtone”, then press {>}.
Select the desired ringtone, then press {>}. Press
{ih}.
To select the dialling mode Press {j/OK}. Select “Base Unit Setup”,
then press {>}. Enter “0000” (default base unit
PIN). Select “Call Options”, then press {>}.
Select “Dial Mode”, then press {>}. Select the
desired setting, then press {>}. Press {ih}.
Feature Operation
To turn the answering system on/off Press {j/OK}. Select “Answer System”, then
press {>}. Select “Answer On” or “Answer
Off”, then press {>}. Press {ih}.
To listen to new/all messages Press {j/OK}. Select “Answer System”, then
press {>}. Select “Play New Msg.” or “Play
All Msg.”, then press {>}.
Feature Operation
TCD210_220FX_QG(e).fm Page 5 Wednesday, January 5, 2005 11:07 AM
PQQW13651ZA DC0105FW0
TCD210_220FX_QG(e).fm Page 6 Wednesday, January 5, 2005 11:07 AM
-
1
-
2
-
3
-
4
-
5
-
6
Panasonic KXTCD220FX Operating instructions
- Type
- Operating instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Panasonic KXTCD203E Operating instructions
-
Panasonic KXTCD224E Operating instructions
-
-
Panasonic KXTCD220FX Owner's manual
-
-
-
Panasonic KXTCD240E Operating instructions
-
-
Panasonic KXTG8102FX Owner's manual
-