American Hearth Lincoln 26 Fireplace (VFD26FP) Owner's manual

Brand: American Hearth

Model: Lincoln 26 Fireplace (VFD26FP)

Category: Fireplaces

Type: Owner's manual

This manual is also suitable for

UNVENTED GAS

FIREPLACE MODELS:

VFD26FM(2,3)0(W,C)(N,P)-2

VFD26FP(2,3)0L(N,P)-2

VFD26FP70L(N,P)-1

VFD26FP30L10(N,P)-3

VFD26FP70L10(N,P)-1

VENT-FREE GAS FIREPLACES

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death or

property damage.

— Do not store or use gasoline or other





— WHAT TO DO IF YOU SMELL GAS

 

 



 

 





 



 





INSTALLER:



CONSUMER:

Retain this manual for future reference.

WARNING

If not installed, operated and maintained

in accordance with the manufacturer's

instructions, this product could expose you



which can cause death or serious illness.

       

    



This appliance is only for use with the type of gas in-

dicated on the rating plate. This appliance is not con-



-







WATER VAPOR: A BY-PRODUCT OF UNVENTED

ROOM HEATERS

       

     



of gas input per hour. Refer to page 8.

INSTALLATION INSTRUCTIONS

AND OWNER'S MANUAL

Page 1

30816-11-0120Page 2

TABLE OF CONTENTS

IMPORTANT SAFETY INFORMATION ..........................................................................................3

SAFETY INFORMATION FOR USERS OF PROPANE GAS .........................................................4

INTRODUCTION ............................................................................................................................5

BUILT-IN FIREPLACE INSTALLATION ..........................................................................................6

FIREPLACE DIMENSIONS ............................................................................................................7

SPECIFICATIONS ..........................................................................................................................8

WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS ........................................8

PROVISIONS FOR ADEQUATE COMBUSTION & VENTILATION AIR ...................................9-10

CONNECTING THE GAS ............................................................................................................10

GAS SUPPLY ............................................................................................................................... 11

CLEARANCES .............................................................................................................................12

COMBUSTIBLE MATERIAL ......................................................................................................... 12

INSTALLATION OF FIREPLACE AND MANTEL ....................................................................13-14

OUTER TRIM INSTRUCTIONS ...................................................................................................15

HOOD INSTRUCTIONS ...............................................................................................................15

LOG PLACEMENT ....................................................................................................................... 16

PLACEMENT OF GLOWING EMBERS (ROCK WOOL) .............................................................17

OPERATION INSTRUCTIONS/FLAME APPEARANCE .............................................................. 18

MAINTENANCE ...........................................................................................................................18

10,000 BTU MILLIVOLT LIGHTING INSTRUCTIONS .................................................................19

MILLIVOLT LIGHTING INSTRUCTIONS .....................................................................................20

INTERMITTENT PILOT LIGHTING INSTRUCTIONS ..................................................................21

HYDRAULIC THERMOSTAT LIGHTING INSTRUCTIONS .........................................................22

PILOT FLAME CHARACTERISTICS ......................................................................................23-24

MAIN BURNER AND THERMOSTAT OPERATION .....................................................................25

MILLIVOLT WIRING .....................................................................................................................26

MILLIVOLT TROUBLESHOOTING ..............................................................................................27

IP ELECTRONIC SYSTEM OPERATING INSTRUCTIONS ........................................................28

IP ELECTRONIC SYSTEM WIRING DIAGRAM .......................................................................... 29

INTERMITTENT CONTROL SYSTEM TROUBLESHOOTING ...............................................30-32

JUNCTION BOX WIRING INSTALLATION INSTRUCTIONS ......................................................33

PARTS LIST ............................................................................................................................34-35

PARTS VIEW ...............................................................................................................................36

FBBX BLOWER KIT EXTENSION INSTALLATION INSTRUCTIONS ....................................37-38

FBB4 OPTIONAL VARIABLE SPEED BLOWER .........................................................................38

FPP26E OPTIONAL BRICK LINER KIT INSTALLATION INSTRUCTIONS .................................39

MASTER PARTS DISTRIBUTOR LIST ........................................................................................ 40

HOW TO ORDER REPAIR PARTS ..............................................................................................40

WARRANTY .................................................................................................................................41

APPLIANCE SERVICE HISTORY ...........................................................................................42-43

SECTION PAGE

30816-11-0120 Page 3

IMPORTANT SAFETY INFORMATION

THIS IS A HEATING APPLIANCE

DANGER: Indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION: Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

NOTICE: Addresses practices not related to personal injury.

 



 



 



 

         

ignition.

 

the same room with the appliance.

 

appliance.

           

fresheners, etc. ) while the log set is in operation. Air fresheners

produce a residue in the air similar to candles and may produce



 

set is in operation. Candles produce a residue in the air that









of soot produced and deposited.

  QUALIFIED SERVICE

PERSON. 











 



room heater and to replace any part of the control system and



 

 

operation.

      







off during initial operation of the appliance. This is a normal





 



      

installation or operation, can settle on surfaces outside the





         













        







WARNING: DO NOT operate this appliance unless all







Log set placement instructions for correct log and twig

positioning.

      

dealer as indicated in the How to Order Repair Parts section of

the appliance manual.

 









WARNING



-

ous gas.

        

-





of instructions, refer to the National Fuel Gas Code, ANSI

      



PILOT LIGHT SAFETY SYS-

TEM designed to turn off the heater if not enough fresh air



DO NOT TAMPER WITH PILOT LIGHT SAFETY SYSTEM!





control compartment clean.

CARBON MONOXIDE POISONING MAY LEAD TO DEATH.



        

Get fresh air at



Some people — pregnant women, persons with heart or lung



         

than others.

The pilot light safety system senses the depletion of oxygen







In this type of application, a fan to circulate the structure air will









30816-11-0120Page 4

-

sions. In its natural state, propane is odorless and colorless.











exactly what to do. If, after reading the following information,

you feel you still need more information, please contact your

gas supplier.

SOME POINTS TO REMEMBER

• Your local

Propane Gas Dealer can give you a "Scratch and Sniff"

pamphlet.Useittondoutwhatthepropaneodorsmells

like. If you suspect that your Propane Gas has a weak or

abnormal odor, call your Propane Gas Dealer.

• If you are not qualied, do not light pilot lights, perform

service, or make adjustments to appliances on the Propane

Gassystem.Ifyouarequalied,consciouslythinkaboutthe

odor of Propane Gas prior to and while lighting pilot lights

or performing service or making adjustments.

• Sometimesabasementoraclosed-uphousehasamusty

smell that can cover up the Propane Gas odor. Do not try

to light pilot lights, perform service, or make adjustments

in an area where the conditions are such that you may not

detect the odor if there has been a leak of Propane Gas.

• Odorfade,duetooxidationbyrustoradsorptiononwalls

of new cylinders and tanks, is possible. Therefore, people

should be particularly alert and careful when new tanks or

cylinders are placed in service. Odor fade can occur in new

tanks,orreinstalledoldtanks,iftheyarelledandallowed

tosettoolongbeforerelling.Cylindersandtankswhich

have been out of service for a time may develop internal

rust which will cause odor fade. If such conditions are sus-

pectedtoexist,aperiodicsnifftestofthegasisadvisable.



Propane Gas Dealer. A periodic sniff test of the Propane

Gas is a good safety measure under any condition.

• If,atanytime,youdonotsmellthePropaneGasodorant

and you think you should, assume you have a leak. Then

take the same immediate action recommended above for

the occasion when you do detect the odorized Propane Gas.

• Ifyouexperienceacomplete"gas out,"(the containeris

under no vapor pressure), turn the tank valve off immediately.

If the container valve is left on, the container may draw in

someairthroughopeningssuchaspilotlightorices.Ifthis

occurs, some new internal rusting could occur. If the valve

is left open, then treat the container as a new tank. Always

be sure your container is under vapor pressure by turning

it off at the container before it goes completely empty or

havingitrelledbeforeitiscompletelyempty.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot smell



out if you can smell the odorant in propane. Smoking can

decrease your ability to smell. Being around an odor for a time

can affect your sensitivity or ability to detect that odor. Some-

times other odors in the area mask the gas odor. People may

not smell the gas odor or their minds are on something else.

Thinking about smelling a gas odor can make it easier to smell.

The odorant in Propane Gas is colorless, and it can fade

under some circumstances. For example, if there is an

underground leak, the movement of the gas through soil can

ltertheodorant.OdorantsinPropaneGasalsoaresubject

tooxidation.Thisfadingcanoccurifthereisrustinsidethe

storage tank or in iron gas pipes.

The odorant in escaped gas can adsorb or absorb onto or

into walls, masonry and other materials and fabrics in a room.

That will take some of the odorant out of the gas, reducing its

odor intensity.

Propane Gas may stratify in a closed area, and the odor inten-

sity could vary at different levels. Since it is heavier than air,

there may be more odor at lower levels. Always be sensitive

to the slightest gas odor. If you detect any odor, treat it as a

serious leak. Immediately go into action as instructed earlier.

PROPANE GAS WARNING ODOR



That's your signal to go into immediate action!

• Donotoperateelectricswitches,lightmatches,useyour

phone. Do not do anything that could ignite the gas.

• Geteveryoneoutofthebuilding,vehicle,trailer,orarea.

Do that IMMEDIATELY.

• Closeallgastankorcylindersupplyvalves.

• PropaneGasisheavierthanairandmaysettleinlowareas

such as basements. When you have reason to suspect

a gas leak, keep out of basements and other low areas.

Stayoutuntilreghtersdeclarethemtobesafe.

• Use your neighbor's phone and call a trained Propane

Gasservicepersonandtheredepartment.Eventhough

you may not continue to smell gas, do not turn on the gas

again. Do not re-enter the building, vehicle, trailer, or area.

• Finally,lettheservicemanandreghterscheckfores-

caped gas. Have them air out the area before you return.

Properly trained Propane Gas service people should repair

the leak, then check and relight the gas appliance for you.

SAFETY INFORMATION FOR USERS OF PROPANE GAS

30816-11-0120 Page 5

Important

All correspondence should refer to complete Model Number, Serial

Number and type of gas.

Attention: During initial use of ceramic log you will detect an

odor as the ceramic log cures.

Notice:Duringinitialring,itspaintwillbakeoutcausingsmoke.

To prevent triggering of smoke alarms, ventilate the room in which

the unit is installed.

Installation on Rugs and Tile

If this appliance is installed directly on carpeting, tile or other

combustiblematerialotherthanwoodooringtheapplianceshall

beinstalledonametalorwoodpanelextendingthefullwidthand

depth of the appliance.

Thebasereferredtoabovedoesnotmeanthere-proofbaseas

usedonwoodstoves.Theprotectionisforrugsthatareextremely

thick and light colored tile.

Solid-fuels shall not be burned in a masonry or UL 127 factory-

builtreplaceinwhichanunventedroomheaterisinstalled.



Installationandreplacement of gas piping, gasutilizationequip-

mentoraccessoriesandrepairandservicingofequipmentshall

be performed only by a  qualied agency.  The term "qualied

agency"meansanyindividual,rm,corporationorcompanywhich

either in person or through a representative is engaged in and is

responsible for (a) the installation or replacement of gas piping or

(b)theconnection,installation,repairorservicingofequipment,who

isexperiencedinsuchwork,familiarwithallprecautionsrequired

andhascompliedwithalltherequirementsoftheauthorityhaving

jurisdiction.

Commonwealth of Massachusetts: The installation must be

madebyalicensedplumberorgastterintheCommonwealth

of Massachusetts.

Sellersofunventedpropaneornaturalgas-redsupplemental

room heaters shall provide to each purchaser a copy of 527 CMR

30 upon sale of the unit.

In the Commonwealth of Massachusetts, unvented propane and

naturalgas-redspaceheatersshallbeprohibitedinbedrooms

and bathrooms.

The installation must conform with local codes or, in the absence

of local codes, with the National Fuel Gas Code, ANSI Z223.1.*

*Available from the American National Standards Institute, Inc. 1430

Broadway, New York, N.Y. 10018.

High Altitudes

For altitudes/elevations above 2,000 feet (610m), ratings should be

reduced at the rate of 4 percent for each 1,000 feet (305m) above

sea level. Contact the manufacturer or your gas company before

changingspud/oricesize.

WARNING



clean may result in sooting and property damage.

Instructions to Installer

1. Installer must leave instruction manual with owner after

installation.

2. Installermusthaveownerlloutandmailwarrantycardsupplied

with unvented room heater.

3. Installer should show owner how to start and operate unvented

room heater.

Always consult your local Building Department regarding regula-

tions, codes or ordinances which apply to the installation of an

unvented room heater.

This appliance may be installed in an aftermarket* manufactured

(mobile) home, where not prohibited by state or local codes.

*Aftermarket: Completion of sale, not for purpose of resale, from

the manufacturer.

Well Head Gas Installations

Some natural gas utilities use “well head” gas. This may affect

the Btu output of the unit and promote sooting. Units shall not be

converted to use well head gas.

This appliance is only for use with the type of gas indicated on the

rating plate. This appliance is not convertible for use with other gases.

WARNING



Improper installation or use of the heater can cause seri-

         

monoxide poisoning.

Operation

Thisunventedreplacerequiresnooutsideventing.Stateandlocal

codesinsomeareasprohibittheuseofunventedreplace.



The valve regulator controls the burner pressure which should be

checked at the pressure test point. Turn captured screw counter

clockwise 2 or 3 turns and then place tubing to pressure gauge over

test point (Use test point “A” closest to control knob). After taking

pressurereading,besureandturncapturedscrewclockwisermly

tore-seal.Donotovertorque.Checkforgasleaks.



When you ignite the pilot, the thermocouple produces millivolts

(electrical current) which energizes the magnet in the gas valve. After

30 seconds to 1 minute time period you can release the gas control

knobandthepilotwillstayON.Allowyourpilotametooperate

an additional one to two minutes before you turn the gas control

knob from the PILOT position to the ON position. This time period

allows the millivolts (electrical current)to build-up to a sufcient

level allowing the gas control to operate properly.

WARNING





General Information

ThisseriesisdesigncertiedinaccordancewithAmericanNational

Standard Z21.11.2 by the Canadian Standards Association as an

Unvented Room Heater and should be installed according to these

instructions.

Any alteration of the original design, installed other than as

shown in these instructions or use with a type of gas not





INTRODUCTION

30816-11-0120Page 6

BUILT-IN FIREPLACE INSTALLATION

Built-In Fireplace Installation

Built-ininstallationofthisreplaceinvolvesinstallingthereplace

intoa framed-inenclosure.Thismakes thefront ofthereplace

ush with a wall. If installing a mantel above the replace, you

must follow the clearances shown in Figure 9. Follow the instruc-

tionsbelowtoinstallthereplaceinthismanner.

Frame in rough opening. Use dimensions show in Figure 1 for a

conventional rough opening. Use dimensions shown in Figure 2

forcornerroughopening.Besuretoprovidegaslineforreplace

and electrical power for optional blower assembly.

1. Attachtwonailingangestoreboxsideswithtwo10x1/2"

screwsforeachnailingange.

2. Gas line connections must be made at this time. When facing

the appliance, the gas supply will enter on the right-hand side.

See "Gas Supply" page 11.

3. Insertreplaceintoenclosure.

4. Attachnailingangestoframingwithascrewornail.

5. Finishedwallsurfacewillbeushtotheleadingedgeofre-

place top and sides.

6. Installationofbuilt-inreplaceiscompleted.

Figure 2

Figure 1

Rough Opening for Installing in Wall

Rough Opening for Installing in Corner

Figure 3

USE ONLY

THE (4)

SIDE NAILING

FLANGES

FOR BUILT-IN

INSTALLATION

30816-11-0120 Page 7

FIREPLACE DIMENSIONS

GAS LINE

OPENING

JUNCTION BOX

ASSEMBLY

GAS

LINE

OPENING

Figure 4

VFD26 SERIES DIMENSIONS

Index Letter Dimension

30 1/4"

768mm

30"

762mm

13 1/8"

333mm

18 1/8"

460mm

26"

660mm

25"

635mm

36 1/4"

921mm

36 1/4"

921mm

51 1/4"

1302mm

30816-11-0120Page 8

SPECIFICATIONS

MODEL VFD26F(M,P)(3,7) VFD26F(M,P)2 VFD26FP(3,7)0L10

InputMaximum 20,000 20,000 10,000

Minimum 14,000 14,000 N/A

NATURAL

Orice 2.10 mm (P-288) #49 (.073") P-265 #53 (.0595") P-214

Air Shutter Opening 1/8" 1/8" 1/8"

PROPANE

Orice #55 (.052") P-182 #55 (.052") P-182 #64 (.036") P-193

Air Shutter Opening 1/4" 1/4" 1/4"

FIREPLACE DIMENSIONS

Height 30 1/4" 30 1/4" 30 1/4"

Depth 13 1/8" 13 1/8" 13 1/8"

Front Width 30" 30" 30"

Rear Width 25" 25" 25"

Gas Inlet 3/8" 3/8" 3/8"

ACCESSORIES

Model Description

FBBX BlowerExtensionKit(MUSTorderFBB4)

FBB4 Automatic Blower (MUST order FBBX)

VPS26HP Bottom Trim Kit

VP2H26HP Hammered Pewter Hood Kit

VPF26HP Hammered Pewter Trim Kit

FPP26E Brick Liner

VPL26HP Hammered Pewter Slat Louver

ACCESSORIES FOR MILLIVOLT VFD26F(M,P)(3,7) ONLY

FRBC Battery Operated Remote Control

FRBTC Battery Operated Remote Control w/Thermostat

FREC Electric Remote Control

FWS-1 Wall Switch

TMV Wall Thermostat, Millivolt - Reed Switch

TRW Wireless Remote Wall Thermostat

Water vapor is a by-product of gas combustion. An unvented room

heaterproducesapproximatelyoneounce(30ml)ofwaterforevery

1,000BTU's(.3KW's)ofgasinputperhour..

Unvented room heaters are recommended as supplemental heat (a

room) rather than a primary heat source (an entire house). In most

supplemental heat applications, the water vapor does not create a

problem. In most applications, the water vapor enhances the low

humidityatmosphereexperiencedduringcoldweather.

The following steps will help insure that water vapor does not

become a problem.

1. Be sure the heater is sized properly for the application, including

ample combustion air and circulation air.

2. Ifhighhumidityisexperienced,adehumidiermaybeusedto

help lower the water vapor content of the air.

3. Do not use an unvented room heater as the primary heat source.

WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS

30816-11-0120 Page 9

3. Add the BTU/Hr of all fuel burning appliances in the space.

Vent-free heater

BTU/Hr

Gas water heater

BTU/Hr

Gas furnace BTU/Hr

Vented gas heater BTU/Hr

Gasreplacelogs BTU/Hr

Other gas appliances* + BTU/Hr

Total = BTU/Hr

Example: Ventedgasheater 20,000 BTU/Hr

Vent-free heater + 18,000 BTU/Hr

Total = 38,000 BTU/Hr

*Do not include direct-vent gas appliances. Direct vent draws

combustion air from the outdoors and vents to the outdoors.

4. ComparethemaximumBTU/Hrthespacecansupportwiththe

actual amount of BTU/Hr used.

BTU/Hr(maximumthespacecansupport)

BTU/Hr (actual amount of BTU/Hr used)

 Example:

  25,600 BTU/Hr(maximumthespacecansupport)

38,000 BTU/Hr (actual amount of BTU/Hr used)

WARNING







         

the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Air for



Thespaceintheaboveexampleisaconnedspacebecausethe

actualBTU/HrusedismorethanthemaximumBTU/HRthespace

can support. You must provide additional fresh air. Your options

are as follows:

A. Rework worksheet, adding the space of an adjoining room. If

theextraspaceprovidesanunconnedspace,removedoor

to adjoining room or add ventilation grills between rooms. See

Ventilation Air From Inside Building.

B. Vent room directly to the outdoors. See Ventilation Air From

Outdoors.

C. Install a lower BTU/Hr heater, if lower BTU/Hr size makes room

unconned.

IftheactualBTU/HrusedislessthanthemaximumBTU/Hrthe

spacecansupport,thespaceisanunconnedspace.Youwillneed

no additional fresh air ventilation.

WARNING



space.

Thisheatershall not be installed in a conned space or unusu-

allytightconstructionunlessprovisionsareprovidedforadequate

combustion and ventilation air.

Aconnedspaceisanareawithvolumelessthan50cubicfeetper

1,000 Btuh of the combined input rates of all appliances drawing

combustionairfromthatspace.Smallareassuchasequipment

roomsareconnedspaces.Furnacesinstalledinaconnedspace

which supply heated air to areas outside the space must draw return

air from outside the space through tightly sealed return air ducts. A

connedspacemusthave2openingsintothespaceforcombus-

tion air. One opening must be within 12 inches of the ceiling and

theothermustbewithin12inchesoftheoor.Therequiredsizing

of these openings is determined by whether inside or outside air is

used to support combustion, the method by which the air is brought

to the space (vertical or horizontal duct) and by the total input rate

of all appliances in the space.

Unusually Tight Construction

The air that leaks around doors and windows may provide enough

fresh air for combustion and ventilation. However, in buildings of

unusually tight construction, you must provide additional fresh air.

      

where:

a. Wallsandceilingsexposedtotheoutsideatmospherehave

a continuous water vapor retarder with a rating of one perm

or less with openings gasketed or sealed, and

b. Weatherstripping has been added on openable windows and

doors, and

c. Caulking or sealants are applied to areas such as joints

around window and door frames, between sole plates and

oors,betweenwall-ceilingjoints,betweenwallpanels,at

penetrations for plumbing, electrical, and gas lines, and at

other openings.

If your home meets all of the three criteria above, you must provide

additional fresh air. See “Ventilation Air From Outdoors,” page

10.



Usethisworksheettodetermineifyouhaveaconnedorunconned

space.

Space: Includes the room in which you will install heater plus any

adjoining rooms with doorless passageways or ventilation grills

between the rooms.

1.Determinethevolumeofthespace(lengthxwidthxheight).

 LengthxWidthxHeight=

cu. ft. (volume of

space)

Example:Spacesize16ft.(length)x10ft.(width)x8ft.(ceiling

height) = 1,280 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills

or openings, add the volume of these rooms to the total volume

of the space.

2. Divide the space volume by 50 cubic feet to determine the

maximumBTU/Hrthespacecansupport.

(volumeofspace)÷50cu.ft.= (maximum

BTU/Hr the space can support)

Example:1,280cu.ft.(volumeofspace)÷50cu.ft.=25.6or

25,600(maximumBTU/Hrthespacecansupport)

PROVISIONS FOR ADEQUATE COMBUSTION & VENTILATION AIR

30816-11-0120Page 10

VENTILATION AIR

Ventilation Air From Inside Building

Thisfreshairwouldcomefromanadjoiningunconnedspace.When

ventilatingtoanadjoiningunconnedspace,youmustprovidetwo

permanent openings: one within 12" of the ceiling and one within

12"oftheooronthewallconnectingthetwospaces(seeoptions

1 and 2, Figure 5). You can also remove door into adjoining room

(see option 3, Figure 5). Each ventilation grill or opening shall have

aminimumfreeareaofonesquareinchper1,000BTU/HRofthe

totalinputratingofthegasequipmentintheconnedspace.

Figure 5

WARNING

       





Ventilation Air From Outdoors

Provideextrafreshairbyusingventilationgrillsorducts.Youmust

provide two permanent openings: one within 12" of the ceiling and

onewith12"oftheoor.Connecttheseitemsdirectlytotheoutdoors

or spaces open to the outdoors. These spaces include attics and

crawl spaces. In most cases for direct communication with the

outdoors or direct communication through a vertical duct a free

areaopeningofonesquareinchper4,000BTU/HRofheaterinput

rating for each grill. If a horizontal duct is used, a grill free area or

ductopeningshallhaveafreeareaopeningofonesquareinchper

2,000 BTU/HR for each grill. Follow the National Fuel Code, ANSI

Z223.1/NFPA 54, Air for Combustion and Ventilation, or applicable

local codes,forrequiredsizeofventilationgrillsorducts.

IMPORTANT: Do not provide openings for inlet or outlet air into attic

if attic has a thermostat-controlled power vent. Heated air entering

the attic will activate the power vent.

Figure 6

PROVISIONS FOR ADEQUATE COMBUSTION & VENTILATION AIR

CONNECTING THE GAS

The inlet connection is located on the right side of the gas valve.

Attach gas inlet line to gas valve.

If installing the an Optional Blower, it must be installed before

connecting the gas line.

30816-11-0120 Page 11

Checkalllocalcodesforrequirements,especiallyforthesizeand

typeofgassupplylinerequired.

RECOMMENDED GAS PIPE DIAMETER

Pipe

Length

Schedule 40 Pipe

Inside Diameter



Outside Diameter

Natural Propane Natural Propane

0-10 feet

0-3 meters

1/2”

12.7mm

3/8”

9.5mm

1/2”

12.7mm

3/8”

9.5mm

10-40 feet

4-12 meters

1/2”

12.7mm

1/2”

12.7mm

5/8”

15.9mm

1/2”

12.7mm

40-100 feet

13-30 meters

1/2”

12.7mm

1/2”

12.7mm

3/4”

19mm

1/2”

12.7mm

100-150 feet

31-46 meters

3/4”

19mm

1/2”

12.7mm

7/8”

22.2mm

3/4”

19mm

NOTICE: Neveruseplasticpipe.Checktoconrmwhetheryour

local codes allow copper tubing or galvanized.

NOTICE: Since some municipalities have additional local codes, it is

always best to consult your local authority and installation code.

Installing a New Main Gas Shut-Off

Each appliance should have its own manual gas shut-off.

A manual main gas shut-off should be located in the vicinity of the

unit.Wherenoneexists,orwhereitssizeorlocationisnotadequate,

contact your local authorized installer for installation or relocation.

Compounds used on threaded joints of gas piping shall be resistant

totheactionofliqueedpetroleumgases.Thegaslinesmustbe

checked for leaks by the installer. This should be done with a soap

solutionwatchingforbubblesonallexposedconnections,andif

unexposed,apressuretestshouldbemade.

WARNING









A gas valve and ground joint union should be installed in the gas

lineupstreamofthegascontroltoaidinservicing.Itisrequiredby

the National Fuel Gas Code that a drip line be installed near the gas

inlet. This should consist of a vertical length of pipe tee connected

into the gas line that is capped on the bottom in which condensation

and foreign particles may collect.

The use of the following gas connectors is recommended:

— ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing

and Fittings

— ANSZ21.45AssembledFlexibleApplianceConnectorsofOther

Than All-Metal Construction

The above connectors may be used if acceptable by the authority

havingjurisdiction.TheCommonwealthofMassachusettsrequires

thataexibleapplianceconnectorcannotexceedthreefeetinlength.

Pressure Testing of the Gas Supply System

1. To check the inlet pressure to the gas valve, a 1/8" (3mm) N.P.T.

plugged tapping, accessible for test gauge connection, must

be placed immediately upstream of the gas supply connection

to the appliance.

2. The appliance and its individual shut-off valve must be

disconnected from the gas supply piping system during any

pressuretestingofthatsystemattestpressuresinexcessof

1/2 psig (3.5 kPa).

3. The appliance must be isolated from the gas supply piping

system by closing its individual manual shut-off valve during

any pressure testing of the gas supply piping system at test

pressuresequaltoorlessthan1/2psig(3.5kPa).

Figure 7

WARNING









   will have a manifold pressure of

approximately3.5"w.c.(.871kPa)formaximuminputor1.7"w.c.

(.423kPa) for minimum input at the pressure regulator outlet with

the inlet pressure to the pressure regulator from a minimum of 5.0"

w.c.(1.120kPa)forthepurposeofinputadjustmenttoamaximum

of 10.5" w.c. (2.614kPa).

2 Series Hydraulic Thermostat Natural Gas will have a manifold

pressure of approximately 6.0" w.c. (1.49kPa) at the pressure

regulator outlet with the inlet pressure to the pressure regulator

from a minimum of 7.0" w.c. (1.74kPa) for the purpose of input

adjustmenttoamaximumof10.5"w.c.(2.615kPa).

     will have a manifold pressure

approximately 10.0"w.c. (2.49kPa) for maximum input or

6.3"w.c. (1.568kPa) for minimum input at the pressure regulator

outlet with the inlet pressure to the pressure regulator from

a minimum of 11.0"w.c. (2.739kPa) for the purpose of input

adjustmenttoamaximumof13.0"w.c.(3.237kPa). 

2 Series Hydraulic Thermostat Propane Gas will have a manifold

pressureapproximately10.0"w.c.(2.49kPa)atthepressureregulator

outlet with the inlet pressure to the pressure regulator from a minimum

of 11.0"w.c. (2.739kPa) for the purpose of input adjustment to a

maximumof13.0"w.c.(3.237kPa).

GAS SUPPLY

30816-11-0120Page 12

Minimum Wall and Ceiling Clearances

36”

(91.44 cm)

2” (5.08 cm)

Figure 8

         



When facing the front of the appliance the minimum clearances to

combustible construction (material) are the following:

 1. Clearancesfromtherightsideorleftsideofthereplaceopening

to any combustible wall or material should not be less than 2

inches.

 2. Clearancesfromthetopofthereplaceopeningtotheceiling

should not be less than 36 inches.

Mantel Clearances for Built-in Installation



Donotattachcombustiblematerialtothemantelofyourreplace.

Thisisarehazard.

HEAT

FLOW

Figure 10

No greeting cards, stockings or ornamentation of any type should be

placedonorattachedtothereplace.Thisisaheatingappliance.

Theowofheatcanignitecombustibles.

Figure 11

CLEARANCES

COMBUSTIBLE MATERIAL

COMBUSTIBLES

ALLOWED

4”

(10.2cm)

5½”

(14.0cm)

2½”

(63.0cm)

4 3/4”

(12.1cm)

6”

(15.2cm)

8 3/4”

(22.2cm)

8”

(20.3cm)

9½”

(24.1cm)

10”

(25.4cm)

10 1/4”

(26.0cm)

12”

(30.5cm)

11”

(27.9cm)

TOPOF FRAME

MANTEL

1. Removereplacefromcarton.

2. Remove mantel top and front base from mantel assembly.

3. Removescrewattachedtoreplacetopandthrough

"L Bracket" attached to back of breast board.

4. Removemantelassemblyfromreplace.

5. Removeshrinkwrapandlogsfromreplace.

6. Placebackbaseandreplaceindesiredlocation.

7. Connect gas line and electrical wiring at this time in accor-

dance with local codes.

ELECTRICAL

CONNECTION

OPENING

GAS LINE

CONNECTION

OPENING

8. Placemantelassemblyaroundreplaceandcenter.Replace

thescrewremovedinstep3tosecurereplacetomantel

assembly.

30816-11-0120 Page 13

INSTALLATION OF FIREPLACE AND MANTEL

11. Place mantel top onto mantel assembly.

12. Install outer trim. See Page 15.

13. InstallberlogspertheLogPlacementInstructions.See

Page 16.

14. Install hood. See Page 15.

9. Attach mantel assembly to studs in the wall through the

"back brace" using two 3" drywall screws provided.

10. Slide front base under front of mantel assembly.

30816-11-0120Page 14

INSTALLATION OF FIREPLACE AND MANTEL

30816-11-0120 Page 15

OUTER TRIM INSTRUCTIONS

1. Remove upper louver, grasp louver at left and right ends; lift and pull forward.

2. Open bottom louver, then lift to remove.

3. Installtherightframeandleftframetothereplace.Alignclearanceholesinframewithscrewholesinreplace.Attachrightframe

andleftframetoreplace.Usetwo8x1/2”Phillipsscrewsforeachframe.

4. Inserttopframeintointerior,topofreplace.Alignclearanceholesintopframewithscrewholesinreplace.Attachtopframeto

replace.Usetwo8x1/2”Phillipsscrewsfortopframe.

5. Replace bottom louver.

6. Replace top louver.

3-PIECE FRAME KIT

SIDE TRIM

HOOD INSTRUCTIONS

1. Remove upper louver, grasp louver at left and right ends; lift and pull forward.

2. Remove screen frame assembly.

3. Outer trim must be installed before installing hood.

4. Placethetophoodangeontopoftherebox,theninstallonescrew(A)atthecenteronventfreereplacethroughthereboxtop

from below.

5. Install one screw (B) at each end of the hood as shown.

6. Replace upper louver.

7. Replace screen frame assembly.

CAUTION



30816-11-0120Page 16

LOG PLACEMENT

 1. Placefrontlogs(#1and#2)betweenfrontgrateangeand

main burner. Align notches on front logs with locator tabs in

base.

2. Place middle log (#3) between front and rear loop of burner.

NOTICE: Do not place log on top of pilot assembly.

 3. Placerearlog(#4)onrearlogshelf.Bottomangeoflogmust

be placed between the log shelf and burner tube.

4. This step is optional for VFD26FP3L10 log sets. Place front

twig(#5)onto(#1)logandatareaon(#3)log.Thebottom

of the front twig is to be placed behind the grate tang that is

second from the left.

Attention: Do not use Figures 12 and 13 to order logs. Refer to

Pages 34 to 35, Parts list and Page 36, Parts View to order logs.

Refer to Figure 12 for the following warning.

CAUTION

Failure to position the parts in accordance with this diagram

    

heater may result in property damage or personal injury.

Figure 12

Figure 13

30816-11-0120 Page 17

Provided with the log set is a small bag of glowing embers (rock

wool)tobeplacedbetweenlogsontheatmetalsurfaceofthe

burner.

Placement of the embers (rock wool) is very individual and light

coverage of the areas indicated will provide your best effects. We

recommend separation of the rock wool by hand and make your

coverageaslightanduffyaspossible.

Place just enough embers (rock wool) on the burner to obtain the

glowandagoldyellowame.

Do not place rock wool over large ports in rear portion of burner.

A thin layer of rock wool should be placed under open space

between the front and middle logs.

Rock wool should not be placed in the area of the pilot assembly.

Glowing embers (rock wool) can cover the burner in between

the front and middle logs, but very little is necessary to cover this

area.Excessembermaterialcausestheyellowametobecome

orange and stringy. Apply just enough to obtain slow glow and a

gold,yellowame.

Replacement of loose material (glowing embers) must be purchased

from Empire Comfort Systems, Inc.Application of excess loose

material (glowing embers) may adversely affect performance of

the heater.

WARNING



to reapplication.

Refer to Parts List, Pages 34 to 35 to order loose material (rock wool).

NOTICE: A single layer of embers is to be used when applying

Platinum Bright Embers (alone or in combination with production

embers) to the burner.

Replacement Loose Material





Rock Wool 15998

Platinum Bright Embers PE-20-1



Figure 14

30816-11-0120Page 18

Flames from the pilot (rear right back side of the burner) as well

as the main ame should be visually checked as the log set is

installed.

Innormaloperationatfullrateafter10to15minutes,theame

appearanceshouldbesetsofyellowames.

NOTICE:Allameswillberandombydesign,ameheightwillgo

up and down.

Avoidanydraftsthatalterburneramepatterns.Donotallowfansto

blowdirectlyintoreplace.Donotplaceablowerinsidetheburner

areaoftherebox.Ceilingfansmaycreatedraftsthatalterame

patterns. Sooting and improper burning will result.

During manufacturing, fabricating and shipping, various components

ofthisappliancearetreatedwithcertainoils,lmsorbondingagents.

These chemicals are not harmful, but may produce annoying smoke

and smells as they are burned off during the initial operation of the

appliance, possibly causing headaches or eye or lung irritation. This

is a normal and temporary occurrence.

The initial break-in operation should last 2-3 hours with the burner

at the highest setting. Provide maximum ventilation by opening

windows or doors to allow odors to dissipate. Any odors remaining

after this initial break-in will be slight and will disappear with

continued use.

PERIODIC CLEANING – Refer to parts diagram for location of



• Donotusecleaninguidtocleanlogsoranypartofheater.

• Logs - brush with soft bristle brush or vacuum with brush

attachment.

• Removeloose particles and dust from the burner areas,

controls, piezo covers and grate.

• Inspectandcleanburnerairintakehole.Removelintorparticles

with brush. Failure to keep air intake hole clean will result in

sooting and poor combustion.

ANNUAL CLEANING/INSPECTION – Refer to parts diagram for



• Inspectandcleanburnerairintakehole.Removelintorparticles

with vacuum or brush. Failure to keep air intake hole clean will

result in sooting and poor combustion.

• Inspectandcleanallburnerports.

• InspectODSpilotforoperationandaccumulationoflintatair

intake holes.

• Verifyamepatternandlogplacementforproperoperation.

• Verifysmoothandresponsiveignitionofmainburner.

OPERATION INSTRUCTIONS/FLAME APPEARANCE

Keep the control compartment, logs and burner area surrounding

the logs clean by vacuuming or brushing area at least twice a year.

WARNING



Always turn off gas to the pilot before cleaning. For relighting, refer

to lighting instructions located on the rating plate of the log set.

Neverobstructtheowofthecombustionandventilationair.Keep

thefrontofthereplaceclearofallobstaclesandmaterials.

Leaveatleast36"clearancefromthefrontofthereplace.

Screen should be closed during operation.

MAINTENANCE

30816-11-0120 Page 19

          

hand. When lighting the pilot, follow these instructions

exactly.

B. BEFORE LIGHTING, smell all around the appliance area





WHAT TO DO IF YOU SMELL GAS

  

  



  

phone. Follow the gas supplier's instructions.

      

department.

C. Use only your hand to push in or turn the gas control

           





or explosion.

 



the appliance and to replace any part of the control system



1. Open bottom louver assembly (if applicable).

2. Set REMOTE/OFF/ON switch to "OFF."

3. Turn off all electric power to the appliance if service is to be

performed (if applicable).

4. Push in gas control knob slightly and turn clockwise

to "OFF". Do not force.

5. Close bottom louver assembly (if applicable).

1. STOP! Read the safety information above on this page.

2. Open bottom louver assembly (if applicable).

3. Set REMOTE/OFF/ON switch to

"OFF".

4. Turn off all electric power to the

appliance (if applicable).

5. Push in gas control knob slightly

and turn clockwise

to "OFF".

NOTE: Knob cannot be turned from "PILOT"

to "OFF" unless knob is pushed in slightly.

Do not force.

6. Wait ten minutes to clear out any gas. Then

smell for gas, including near the

oor.Ifyousmellgas,STOP!Fol-

low "B" in the safety information

above. If you do not smell gas, go

tothenextstep.

7. Find pilot - Follow metal tube from

gas control. The pilot is located

next to theburner, nearthe right

side.

8. Turn gas control knob counterclockwise

to "PILOT".

9. Push in control knob all the way and hold in. Repeatedly push

the Piezo Ignitor Button until the pilot is lit. Continue to hold

the control knob in for about one minute after the pilot is lit.

Release knob, and it will pop back up. Pilot should remain lit.

If it goes out, repeat steps 5 through 9.

 • Ifknobdoesnotpopupwhenreleased,STOPandIM-

MEDIATELY call a qualied service technician or gas

supplier.

 • Ifthepilotwillnotstaylitafterseveraltries,turnthegas

control knob to "OFF" and call your service technician or

gas supplier.

10. Turn gas control knob counterclockwise to "ON".

11. Set REMOTE/OFF/ON switch to desired setting.

12. Turn on all electric power to the appliance (if applicable).

13. Close bottom louver assembly (if applicable).

GAS CONTROL KNOB

SHOWN IN "OFF" POSITION.

THERMOCOUPLE

(NATURAL)

ELECTRODE

PILOT

THERMOPILE

REMOTE

OFF

THERMOCOUPLE

(LPG)

GAS CONTROL KNOB

SHOWN IN "OFF" POSITION.

THERMOCOUPLE

(NATURAL)

ELECTRODE

PILOT

THERMOPILE

REMOTE

OFF

THERMOCOUPLE

(LPG)

10,000 BTU MILLIVOLT LIGHTING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING

LIGHTING INSTRUCTIONS

TO TURN OFF GAS TO APPLIANCE

WARNING



personal injury or loss of life.

30816-11-0120Page 20

MILLIVOLT LIGHTING INSTRUCTIONS

          

hand. When lighting the pilot, follow these instructions

exactly.

B. BEFORE LIGHTING, smell all around the appliance area





WHAT TO DO IF YOU SMELL GAS

  

  



  

phone. Follow the gas supplier's instructions.

      

department.

C. Use only your hand to push in or turn the gas control

           





or explosion.

 



the appliance and to replace any part of the control system



1. Open bottom louver assembly (if applicable).

2. Set REMOTE/OFF/ON switch to "OFF."

3. Turn off all electric power to the appliance if service is to be

performed (if applicable).

4. Push in gas control knob slightly and turn clockwise

to "OFF". Do not force.

5. Close bottom louver assembly (if applicable).

1. STOP! Read the safety information above on this page.

2. Open bottom louver assembly (if applicable).

3. Set REMOTE/OFF/ON switch to

"OFF".

4. Turn off all electric power to the

appliance (if applicable).

5. Push in gas control knob slightly

and turn clockwise

"OFF".

NOTE: Knob cannot be turned from "PILOT"

to "OFF" unless knob is pushed in slightly.

Do not force.

6. Wait ten minutes to clear out any

gas. Then smell for gas, including

near the oor. If you smell gas,

STOP! Follow "B" in the safety

information above. If you do not

smellgas,gotothenextstep.

7. Find pilot - Follow metal tube from

gas control. The pilot is located

next to theburner, nearthe right

side.

8. Turn gas control knob counterclockwise

to "PILOT".

9. Push in control knob all the way and hold in. Repeatedly push

the Piezo Ignitor Button until the pilot is lit. Continue to hold

the control knob in for about one minute after the pilot is lit.

Release knob, and it will pop back up. Pilot should remain lit.

If it goes out, repeat steps 5 through 9.

 • Ifknobdoesnotpopupwhenreleased,STOPandIM-

MEDIATELY call a qualied service technician or gas

supplier.

 • Ifthepilotwillnotstaylitafterseveraltries,turnthegas

control knob to "OFF" and call your service technician or

gas supplier.

10. Turn gas control knob counterclockwise to "ON".

11. Set REMOTE/OFF/ON switch to desired setting.

12. Turn on all electric power to the appliance (if applicable).

13. Close bottom louver assembly (if applicable).

GAS CONTROL KNOB

SHOWN IN "OFF" POSITION.

THERMOCOUPLE

(NATURAL)

ELECTRODE

PILOT

THERMOPILE

REMOTE

OFF

THERMOCOUPLE

(LPG)

GAS CONTROL KNOB

SHOWN IN "OFF" POSITION.

THERMOCOUPLE

(NATURAL)

ELECTRODE

PILOT

THERMOPILE

REMOTE

OFF

THERMOCOUPLE

(LPG)

GAS CONTROL KNOB

SHOWN IN "OFF" POSITION.

THERMOCOUPLE

(NATURAL)

ELECTRODE

PILOT

THERMOPILE

REMOTE

OFF

THERMOCOUPLE

(LPG)

FOR YOUR SAFETY READ BEFORE LIGHTING

LIGHTING INSTRUCTIONS

TO TURN OFF GAS TO APPLIANCE

WARNING

personal injury or loss of life.

Page is loading ...

American Hearth Lincoln 26 Fireplace (VFD26FP) Owner's manual

Brand: American Hearth

Model: Lincoln 26 Fireplace (VFD26FP)

Category: Fireplaces

Type: Owner's manual

This manual is also suitable for

Download PDF

report

American Hearth Lincoln 26 Fireplace (VFD26FP) Owner's manual

This manual is also suitable for

American Hearth Lincoln 26 Fireplace (VFD26FP) Owner's manual

Related papers

Other documents