George Kovacs P1732-286-L User manual

Brand: George Kovacs

Model: P1732-286-L

Type: User manual

George Kovacs P1732-286-L is a stylish and functional outdoor wall light designed to illuminate your exterior spaces with warm, inviting light. It features a sturdy construction with a durable finish, ensuring long-lasting performance. Installation is easy with all necessary hardware included. The light is compatible with AC LED 8W bulbs, delivering energy-efficient illumination.

Fig.4

INSTALLATION INSTRUCTIONS

For Model # P1731-L/P1732-L

READ AND SAVE THESE INSTRUCTIONS

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARING FOR INSTALLATION (Fig. 1)

1. Shut off power at the circuit breaker and remove the old fixture,

including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts on a clear

area. Take care not to lose any parts necessary for installation.

3. Unscrew the screws (G) and separate the mounting plate (B) (Part #

A-020-150) from back plate (H).

4. Attach the mounting plate(B) to the outlet box (not provided) with the

two outlet box screws (C) (Size: 8-32*1”).

Note: the side of mounting plate marked “GND” must face out.

GLASS INSTALLATION (Fig. 1)

5. Using Allen wrench (J) to unscrew pre-assembled Allen screws (K)

from cap (I).

6. Install glass shade (L) into cap (I) and secure it by using Allen

wrench (J) to screw Allen screws (K) through pre-drilled hole of cap

(I) and then into pre-drilled hole of the glass shade (L).

CONNECTION THE WIRES (Fig. 2)

7. Connect the electrical wires as shown in (Fig.2), making sure that all

wire connectors (D) are secured. If your outlet has a ground wire

(green or bare copper), connect the fixture ground wire to it.

Otherwise, connect the fixture ground wire directly to the mounting

plate using the green screw provided.

FINISHING THE INSTALLATION (Fig.1)

8. Align back plate (H) onto mounting plate (B) and secure with the

screws (H).

9. To prevent moisture from entering the outlet box and causing

shortage, use clear caulking (i.e. Indoor/Outdoor Silicone Sealant) to

outline the outside of fixture back-plate where it meets the wall

leaving space at bottom to allow moisture a means to escape.

(Fig.3)

10. Bulb information: (1 x AC LED 8W included for P1731-L and 1 x AC

LED 8W included for P1732-L.)

DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS

DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

Your installation is now complete. Return power to the junction box and

test the fixture.

Replacing LED module (Fig. 4)

The LED module can be replaced by a qualified electrician and shut off the

power at the circuit breaker and remove fixture from the outlet box without

cutting of wire and without damage to any decorative element to which the

fixture is attached. See installation steps for more details (Fig 4.)

a. Shut off power.

b. Taking back plate (H) off from wall and unscrew screws (K) to separate

glass shade (L) from the cap (I).

c. Remove the broken LED Module for re-lamping by taking wire connectors

away and loosening screws (O).

d. Wiring new LED Module wires through the pre-drilled hole in the back plate

(H) and secure the new LED Module by screws (O),washer (N) and plastic

tube (M) as Fig 4 showed.

Note: The LED module should be provided by a specified supplier.

Fig.1

IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A QUALIFIED

ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION.

Fig.4

(HOT)

(NEUTRAL)

HOUSE

WIRES

BLACK

HOUSE

WIRES

WHITE

BARE COPPER(GROUND)

HOUSE

GREEN OR

WIRES

FIXTUREFIXTURE

WIRES

FIXTURE

WIRES

BARE

(GROUND)

COPPER

WHITE

RIBBED

BLACK

SMOOTH

GREEN OR

Fig.2

WIRES

Fig. 3

Caulking

Backplate

George Kovacs P1732-286-L User manual

Brand: George Kovacs

Model: P1732-286-L

Type: User manual

Download PDF

report

George Kovacs P1732-286-L User manual

George Kovacs P1732-286-L User manual

Related papers

Other documents