Aurora Health & Beauty STM311 User manual

Brand
Aurora Health & Beauty
Model
STM311
Category
Massagers
Type
User manual
STM311
REMOVE THE MESH COVER
To remove the mesh cover, place your
thumb on the notch, pull downward as
shown in figure (A) above
INSTALL THE MASSAGE HEAD
To install the massage head, first select
the desired head and then connect it by
pressing the head upward onto the
bottom piece of the massager as shown
in figure (C) above.
REMOVE THE MASSAGE HEAD
To remove the massage head, place your
thumb on the notch, pull downward to
remove the massage head as shown in
figure (B) above.
INSTALL THE MESH COVER
To install the mesh cover, place the mesh
cover over the massage head by pressing
the mesh cover upward as shown in figure
(D) above.
210x285mm
IMPORTANT SAFETY INSTRUCTIONS
When using the electrical appliance, basic safety precautions as listed below should always be followed:
Read all instructions before using this handheld Massager.
– To reduce the risk of electric shock
1) Always unplug this appliance from the electrical outlet immediately after using or before cleaning.
2) Do not reach for an appliance that has fallen into water. Unplug immediately.
3) Do not use while bathing or in a shower.
4) Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
– To reduce the risk of burns, fire, electric shock, or injury to individuals :
1) An appliance should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or
taking off parts.
2) Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury to individuals.
3) Close supervision is necessary when this appliance is used by, on, or near children, invalids, or disabled persons.
4) Use this appliance only for its intended use as described in this manual. Do not use attachments which are not recommended
by the manufacturer.
5) Never operate this appliance if it has a damaged cord or plug, if it is not working properly, dropped into water or damaged.
Please return the appliance to a service center for examination and repair.
6) Do not carry this appliance by supply cord or use cord as a handle.
7) Keep the cord away from heated surfaces.
8) Never operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and the like. Never operate
on a soft surface such as a bed or couch where the air openings may be blocked.
9) Never drop or insert any object into any opening.
10) Do not use in outdoors.
11) Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
12) To disconnect,remove plug from outlet.
13) The appliance is intended for household and indoor use only.
14) Please ensure the power is off before open mesh cover.
Scraping Therapy Massager
ASSEMBLY INSTRUCTIONS
OPERATION PROCEDURES
Specifications
FEATURES
RELAX
The Scraping Therapy Massager combines ancient Chinese acupuncture techniques with modern technology to loosen
and relax stiff muscles.
It’s a great way to bounceback after the most intense workday or workout.
- Speed control which allows you to adjust different massaging needs.
- lnterchangeable heads, including a soft mesh cover.
- The easy-to-grip handle helps reach every part of your body.
1. Insert the plug securely into the wall socket.
2. Turn the switch on activates massage operation and controls speed.
3. Turn clockwise to increase the massager speed.
4. Turn counter-clockwise to decrease the massager speed.
5. Turn the switch off deactivate massage operation and disconnect power.
Product Name: Scraping Therapy Massager
Item NO.: STM311
Input power: AC 110V~60Hz
Power consumption: 12W
Speed: 3000±10%RPM
Replaceable wave
massager head
Mesh cover
Replaceable rolling
massager head
TROUBLESHOOTING
If the problem occur is not listed above, please follow the steps below:
1. Pull out the power plug from the wall scoket.
2. Let the device remain turned off for 60 minutes.
3. After 60 minutes, plug the device into the wall socket and turn on the switch.
If the problem persists, please contact the authorized service center immediately.
If you can not solve the problem with the following information, please contact the authorized service center.
Problem Possible Cause Solution
Plug is disconnected.
An excessive weight has been placed on
the appliance (e.g. someone stood on the
appliance, or put a heavy object on it).
Unplug the device, remove the excessive weight
and switch on the device again.
The device is warm.
The device has performed several 15-minutes
sessions in a row.
Unplug the device and let it cool down. Keep
unplug the device after use.
The device is making
some sounds.
This sound is caused by the mechanical
structure of the device.
This is normal and does not mean the device is
malfunctioning.
Cord is broken, or
smoke is coming from
the device.
Stop using the product immediately and contact
the authorized service center.
The device does
not work.
Insert the plug securely into the wall socket.
SAVE THESE INSTRUCTIONS.
A B
C D
  • Page 1 1

Aurora Health & Beauty STM311 User manual

Brand
Aurora Health & Beauty
Model
STM311
Category
Massagers
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents