Design House 547711 Installation guide

Design House
Brand
Design House
Model
547711
Category
Sanitary ware
Type
Installation guide
SINGLE HANDLE TUB&SHOWER
FAUCET WITH PRESSURE
BALANCE DEVICE
4-8-16
Design House is a registered brand
of DHI Corp.Mequon,WI 53092
1-800-558-8700
PREPARATION
SAFETY INFORMATION
Before beginning assembly of product, make sure all parts are present.
Compare parts with package contents list and hardware contents. If any
part is missing or damaged, do not attempt to assemble the product.
Contact customer service for replacement parts.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): Adjustable Wrench, Groove
Joint Pliers, Pipe Wrench, Phillips Head Screwdriver, and Supply Lines.
Installations may vary depending on how the previous faucet was
installed. Supplies necessary for the installation of the faucet are not
all included; however, they are available wherever plumbing supplies
are sold.
Prior to beginning installation, turn off the hot and cold water lines, then
turn on the old faucet to release built-up pressure. When installing the
new faucet, hand tighten the connector nuts. DO NOT OVERTIGHTEN.
Connections that are too tight will reduce the integrity of the system.
Please read and understand this entire manual before attempting to
assemble, operate or install the product.
WARNING
• Protect your eyes with safety glasses when cutting or soldering water
supply lines.
CAUTION
• If you solder the joints during installation of the faucet, the seats,
or the warranty will be voided on these parts.
• Cover the sink drain to avoid losing parts.
MODELS
547679-Satined Nickel
547661-Polished Chrome
547687-Polished Chrome
547703-Satined Nickel
547604-Polished Chrome
547612-Satined Nickel
547711-Polished Chrome
547729-Satined Nickel
www.todaysdesignhouse.com
PRODUCT SPECIFICATIONS
SPECIFICATIONS SPECIFICATIONS
Max. Flow Rate: 2.0 GPM (7.56 LPM) Ceramic cartridge
ASME A112.18.1/CSA B125
Polish chrome or Satined Nickel
Notes: The picture in this installation instructions is for reference only, pls refer to actual
product in installation process.
2
www.todaysdesignhouse.com
ASSEMBLY INSTRUCTIONS
Recommended component locations:
(see Fig . 1)
Recommended depth for valve body
in wall is 2-1/2”(2-1/8”MIN-2-3/4”MAX) .
1A . Shower and / or spout outlet hole :
1-1/4” diameter .
1B . Valve access hole :
3-3/4” MIN - 4-3/4” MAX . diameter .
1
Assembly
A . Position valve body correctly in wall
(see Fig . 2 ) . UP marking is on up side
and DOWN marking on down side .
B . Remove valve screws of plastic valve
C . Turn on hot and cold water
supply lines .
Note : Pressure must be approximately
equal on both hot and cold sides for
valves to function properly .
D . Rotate stem to allow water to flow
From tub spout until there is no
foreign matter in discharge .
2
Assembly
A . Install A 1/2” iron pipe plug
(not included) on both shower and tub
outlets .Turn stem to full “ ON ” and check
all connections for leaks .
B. Turn stem to “OFF” .
3
4
5
A . Caution : Slowly remove pipe plugs
from shower and tub outlets .
B . After wall treatment , remove
escutcheon screws.
C . Install sleeve and screw
bonnet onto body.
D . Optional sticker for marking of “red”-hot
and “ blue ”-cold to escutcheon .
“ red ” direct to hot side and “ blue ”
direct to cold side .
E . Install the handle assembly
(see Fig . 3 ) .
A . Install tub spout and shower arm
(see Fig . 4) .
Anti-scald ring: this device limits the
maximun temperature to avoid accidental
scalding. It can be set in any of several
positions to achieve the desired
temperature.
A. Remove the handle assembly to
reveal the limiter (see Fig. 3).Located
B. Remove the inverter and the sleeve.
C. Ensure the Down limiter unmoved,
adjust theUp limiter to desired
temperature (see Fig. 5,6 and 7).
Note: Recommended location is shown
in Fig. 6.
Hot water adjustment
Position in the middle is
recommended
Cold water adjustment
protector.
on the front of the cartridge.
3
www.todaysdesignhouse.com
CARE AND MAINTENANCE
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Clean peridodically with a soft cloth.Avoid abraisive cleaners,steel wool, and harsh chemicals as these will dull
the finish and void your warranty
3
www.todaysdesignhouse.com
CARE AND MAINTENANCE
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Clean peridodically with a soft cloth.Avoid abraisive cleaners,steel wool, and harsh chemicals as these will dull
1. Remove faucet handle, cartridge, housing and valve spool to
check the rubber valve seal. Clean it or replace by calling
Customer Service.
Leaks from
spout
Damaged or dirty valve
seat.
Bonnet is loose
or bottom
gasket on
cartridge is
dirty or twisted.
Bonnet is loose or
bottom gasket on
cartridge is dirty or
twisted.
1.
Remove faucet handle. Tighten the bonnet. Clean or replace
O-ring.
4
www.todaysdesignhouse.com
LIMITED LIFETIME WARRANTY
The distributor warrants to the original consumer purchaser this product to be free from defects in material and
workmanship under normal use in residential applications.At its option, the Company will provide repair parts or
replace defective product when the product is used in accordance with the manufacturer's specifications.
The distributor provides a limited warranty on the finish of this product to the original purchaser.At its option, the
distributor will provide repair parts or replace defective product when the product is used in accordance with the
manufacturer's specifications.Use of mild abrasive,abrasive or chemical cleaners may damage the finish of the
faucet.We recommend cleaning your faucet with a soft cloth, moistened with water.Damage resulting from the
use of abrasive or chemical cleaners SHALL VOID THIS WARRANTY.
This warranty is not applicable to any products or parts of products where damage is caused by use of non-
genuine parts; is due to installation error, product misuse, negligence or faulty maintenance; or where the
product is not installed according to local building codes.
This warranty excludes labor charges or damage incurred during installation, repair or replacement, and any
indirect, incidental or consequential damages, losses, injury or costs of any nature. This warranty is in lieu of
and excludes all other warranties, conditions and guarantees, whether expressed or implied, including without
restriction those of merchantability or fitness of use.Liability under this warranty will not exceed the purchase
price for the product claimed to be defective by the original consumer purchaser. Some states or provinces do
not allow the exclusion or limitation of consequential damages so the above limitations or exclusions may not
apply. This warranty gives you specific legal rights and you may also have other rights which vary from state to
state, or province to province.
Inquiries regarding warranty claims can be directed to 1-800-558-8700,8 a.m. - 5 p.m., CST, Monday - Friday.
  • Page 1 1
  • Page 2 2

Design House 547711 Installation guide

Design House
Brand
Design House
Model
547711
Category
Sanitary ware
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents