Contec CPS-PAV-AE01-JP Owner's manual

Brand: Contec

Model: CPS-PAV-AE01-JP

Type: Owner's manual

Technical Guide

CONTENTS

Signal Tower Light Sensor

CPS-PAV-AE Series

Introduction .................................................................. 4

Screen Menu .............................................................. 13

HMI Controls .............................................................. 40

Customizing ................................................................ 46

Appendix ...................................................................... 64

FAQ ................................................................................ 78

Customer Support and Inquiry ............................ 88

— 2 —

Table of Contents

Introduction ...................................................................... 4

1. CPS-PAV-AE Series Technical Guide ................................................................................................................5

2. Related Manuals ......................................................................................................................................................6

3. Check Your Environment Before Using the Product. ................................................................................7

4. Precautions on Handling the Product ............................................................................................................8

Screen Menu ................................................................... 13

1. Top-Menu ............................................................................................................................................................... 14

1. Start Up CONPROSYS WEB Setting ........................................................................................................ 14

2. Open the Top-Menu .................................................................................................................................... 14

2. Setting Menus ....................................................................................................................................................... 16

1. Screen Transition ........................................................................................................................................... 16

2. Transmitter Information .............................................................................................................................. 17

3. Transmitter Settings ..................................................................................................................................... 19

4. Condition Name Assignment List ........................................................................................................... 21

5. Condition Name Assignment ................................................................................................................... 22

6. Sensitivity Setting .......................................................................................................................................... 24

7. Abnormal State Alert Mail Setting ......................................................................................................... 25

8. Low Battery Mail Notification Setting ................................................................................................... 26

9. Duplicate Settings ......................................................................................................................................... 27

10. Light State Management ............................................................................................................................ 28

11. Receiver Information .................................................................................................................................... 29

3. Monitoring Screens............................................................................................................................................. 31

1. Screen Transition ........................................................................................................................................... 31

2. Condition Monitoring (Andon Style Group Monitoring) ........................................................... 32

3. Condition Monitoring (Timeline Bars) .................................................................................................. 34

4. Graphical Monitoring (Facility Map) ...................................................................................................... 37

4. Log Files ................................................................................................................................................................... 38

1. Screen Transition ........................................................................................................................................... 38

2. Display Files ..................................................................................................................................................... 39

HMI Controls .................................................................. 40

1. Tower Light Controls .......................................................................................................................................... 41

1. Optional Settings .......................................................................................................................................... 41

2. Controlling the Lighting ............................................................................................................................. 42

2. Andon Controls .................................................................................................................................................... 43

1. Optional Settings .......................................................................................................................................... 43

2. Controlling the Condition .......................................................................................................................... 44

3. Pictograph Display Patterns ...................................................................................................................... 45

Customizing .................................................................... 46

1. Register Facility Map .......................................................................................................................................... 47

1. How to Register Facility Map Image ...................................................................................................... 47

— 3 —

Table of Contents

2. Placing the Tower Light Controls ............................................................................................................ 51

2. Add States............................................................................................................................................................... 54

1. Register a State Name ................................................................................................................................. 54

2. Assign Light Condition ................................................................................................................................ 56

3. Add a Condition/State Name to the Condition Monitoring Screen ......................................... 58

3. Add VTC ................................................................................................................................................................... 63

Appendix ........................................................................ 64

1. Measurement Data Management (Common Variables) ....................................................................... 65

1. Common Variables Data List ..................................................................................................................... 65

2. Data Retained for Common Variables .................................................................................................. 67

2. Alert Mail Task ....................................................................................................................................................... 69

1. Subroutine ....................................................................................................................................................... 69

2. Tasks ................................................................................................................................................................... 70

3. Cautions ............................................................................................................................................................ 73

3. Light Blinking Specification ............................................................................................................................. 74

4. About Data Files ................................................................................................................................................... 75

1. Log Data CSV File .......................................................................................................................................... 75

2. Graph CSV File ................................................................................................................................................ 76

3. Cautions ............................................................................................................................................................ 77

FAQ .................................................................................. 78

1. Want to Update Firmware ................................................................................................................................ 79

1. Check Your Firmware Version ................................................................................................................... 79

2. Check the Registered Version .................................................................................................................. 79

3. Update Your Firmware Version ................................................................................................................ 79

2. Want to Restore Defaults .................................................................................................................................. 80

1. Set the Dip Switches .................................................................................................................................... 80

2. Reboot the CONPROSYS ............................................................................................................................ 80

3. Complete Defaults Restoring ................................................................................................................... 80

3. Unable to Confirm the Light ON/OFF Properly ....................................................................................... 81

1. Check the Measured Value When the Tower Light is OFF ............................................................ 83

2. Check the Measured Value When the Tower Light is ON ............................................................. 84

3. Calculate the sensitivity .............................................................................................................................. 84

4. Save the Adjustments .................................................................................................................................. 85

4. Supported Models .............................................................................................................................................. 86

1. M2M Controller ............................................................................................................................................. 86

Customer Support and Inquiry ..................................... 88

1. Services .................................................................................................................................................................... 89

— 4 —

Introduction

This section provides necessary information of the product

such as the outline and manuals before actual use.

—

Introduction

—

CPS-PAV-AE Series Technical Guide

— 5 —

1. CPS-PAV-AE Series Technical Guide

This guide describes the details on the screen of the Signal Tower Light Sensor system.

Furthermore, the technical information is provided for users to help them customize the programs

with their equipment.

- About HMI controls for this product

- About common variables (information on TAG, STAG)

- About alert mail task (VTC)

- About log file

- How to customize a monitoring screen

Please use this manual as information materials to build the environment that fits your own

conventions.

—

Introduction

—

CPS-PAV-AE Series Technical Guide

— 6 —

2. Related Manuals

The manuals related to the product are listed below. Read them as necessary along with this guide.

 Must Read the Following Manuals.

Name

Purpose

Contents

How to get

Setup Guide

Must read this after

opening the package.

This lists the product

configuration and describes

the precautions.

Included in the package

(Printed matter)

Technical Guide

(this manual)

Read this when setting up

the "CONPROSYS WEB

Setting"

This describes how to set

each function of

"CONPROSYS WEB Setting".

Download from

the Contec

website (PDF)

 Download Manuals

Download the manuals accordingly from the following URL.

Download

https://www.contec.com/download/

—

Introduction

—

CPS-PAV-AE Series Technical Guide

— 7 —

3. Check Your Environment Before Using

the Product.

This section describes requirements for using the product.

 Firmware Versions

The firmware in The CONPROSYS supports the following versions.

Compatible Web browsers

Supported Versions

Integrated type

Ver. 3.4.1 or later

Configurable type

Ver. 3.5.1 or later

Gateway model

Ver. 3.4.1 or later

If your system is using a different version from the ones listed above, visit our website and download

the CONPROSYS firmware, then update to the latest one.

Download

https://www.contec.com/download/

 Web Browsers and Versions

Settings and the monitoring screen display are performed through a web browser.

The following web browsers and versions are supported.

Compatible Web browsers

Supported Versions

Microsoft Internet Explorer

Ver. 11 or later

Google Chrome

Ver. 52 or later

Mozilla Firefox

Ver. 55 or later

* Problems may arise due to the use of incompatible browser. Be sure to use the web browser

that is compatible.

—

Introduction

—

CPS-PAV-AE Series Technical Guide

— 8 —

4. Precautions on Handling the Product

This section describes precautions when handling the product.

 About Date and Time on the product

If your CONPROSYS model has no RTC backup battery, the date and time on the product return to

their initial settings when booting the CONPROSYS. If you start monitoring with wrong date and time

on the Condition monitoring screen (Timeline Bars), the bars cannot be updated and it fails to

monitor properly.

The warning dialog box appears upon selecting the product menu if the date and time are incorrect.

(This applies to the product with Ver1.0.3 or later versions, and the warning is displayed one time

only when booting the CONPROSYS.)

Setting the correct date and time is required before you start monitoring on the Condition

monitoring (Timeline Bars).

 Setting date and time

Refer to "9. Time" in the "CONPROSYS Reference Manual (Software)".

 Checking which CONPROSYS has a RTC backup battery

Refer to the "FAQ - 4. Supported Models" in this guide and check the lists.

Note that the time settings has no effect on Condition monitoring (Andon) and Graphical monitoring.

—

Introduction

—

CPS-PAV-AE Series Technical Guide

— 9 —

 When Turning the Power Off

When turning off the power of the CONPROSYS, perform the "Shutdown" in the sub-menu in Setting

Menus first.

If you physically turn off the power, it may damage the files stored on the SD card. This could result

in failure to update the Condition monitoring (Timeline Bars).

 When Rebooting the Product

When you reboot the CONPROSYS, perform the "Reboot" in the sub-menu in Setting Menus for the

same reason mentioned above.

—

Introduction

—

CPS-PAV-AE Series Technical Guide

— 10 —

 Updating firmware to Version 1.0.3

The screen of the Condition monitoring (Timeline Bars) will be changed.

If you have performed the "Save the monitoring screens to ROM" with the former version, updating

firmware to version1.0.3 cannot be applied automatically to the latest screen.

Follow the procedure described below to apply the updated firmware to the screen.

Open the Monitoring Screens

From Top Menu, click the "Editor" of the Condition monitoring (Timeline Bars).

The condition monitoring (Timeline Bars) opens as an editor.

—

Introduction

—

CPS-PAV-AE Series Technical Guide

— 11 —

Open the latest template of the Timeline Bars

From File menu, select the "Open page", and select /template/OpeGraph103.page in the [Open page]

dialog box to open the latest template.

Save the template

From File menu, select the "Save page as", and select /user/OpeGraph.page in the [Save page] dialog

box to overwrite and save the template.

—

Introduction

—

CPS-PAV-AE Series Technical Guide

— 12 —

Save the settings to ROM

From File menu, perform the "Save the settings to ROM".

— 13 —

Screen Menu

This section describes the details on setting menus and

monitoring screens of the product.

—

Screen Menu

—

CPS-PAV-AE Series Technical Guide

— 14 —

1. Top-Menu

This section describes the details on setting menus and monitoring screens of the product.

1. Start Up CONPROSYS WEB Setting

Settings are performed through the "CONPROSYS WEB Setting".

For start-up procedure, refer to the "Setup Guide" included in the package.

2. Open the Top-Menu

The image below is the top-menu of the Setting Menu.

From the sub-menu in the CONPROSYS WEB Setting, click the Signal Tower Light Sensor to open the

menu.

—

Screen Menu

—

CPS-PAV-AE Series Technical Guide

— 15 —

No.

Name

Function

Setting Menus

This is a menu to the screens that display settings and status definitions of

the transmitter as well as receiver information.

The details are explained in the "2. Setting Menus".

Monitoring Screens

This is a menu to the monitoring screens that display condition

monitoring and facilities map.

The details are explained in the "3.Monitoring Screens".

Log Files

This is a menu to the screens that display data file output at the time of

operation. The details are explained in the "4. Log Files".

Click the [Return] to return to the top screen of the “CONPROSYS WEB Setting”.

—

Screen Menu

—

CPS-PAV-AE Series Technical Guide

— 16 —

2. Setting Menus

This section describes the various types of setting on the screen.

1. Screen Transition

The transition from Top Menu to each setting is listed below.

The details of each setting are described on the following pages.

—

Screen Menu

—

CPS-PAV-AE Series Technical Guide

— 17 —

2. Transmitter Information

This screen lists the information of registered transmitters to be monitored.

No.

Name

Function

Transmitter Information

The information of registered transmitters is listed.

The Information of transmitter registration No., transmitter ID, facility

name, radio strength level, and battery level are displayed.

Change, Delete

[Change] Click this button to change the selected transmitter information.

[Delete] Click this button to delete the selected transmitter information.

Advanced Setting

Click this button to configure the advanced setting on the selected

transmitter. The following buttons appear when clicking this button.

Add

Click this button to register a new transmitter.

Click the [Return] to return to TOP-Menu.

—

Screen Menu

—

CPS-PAV-AE Series Technical Guide

— 18 —

 When A Transmitter Cannot Be Identified

Click the [Add] button, and the warning dialog box appears instead of the [Transmitter Settings]

screen.

Check the installed Transmitter, then click the Update button. Confirm that the screen changes to the

Transmitter Settings.

—

Screen Menu

—

CPS-PAV-AE Series Technical Guide

— 19 —

3. Transmitter Settings

The transmitter that performs monitoring can be added or changed on this screen.

No.

Name

Function

This number is uniquely assigned to each connectable transmitter with

the product.

Transmitter ID

Assign ID of transmitter.

IDs of the operating transmitters in the facilities are automatically

identified, and they are displayed in the list as shown below, by clicking

the ▼ button.

Select the ID of transmitter to be assigned.

Facility Name

Decide the facility name of which the transmitters are set.

Set

Click the "Set" button to complete the transmitter settings.

Click the [Return] to return to Top-Menu.

—

Screen Menu

—

CPS-PAV-AE Series Technical Guide

— 20 —

 About Transmitter No.

This number is uniquely assigned to each connectable transmitter with the product.

(Number 1 to 16 are automatically assigned.)

The transmitter No. specified when linking with HMI controls (Tower Light controls, ANDON controls)

for this product, or the common variables that contain the measurement data are assigned to each

of these numbers.

 About Transmitter ID

This ID is uniquely assigned to each EnOcean transmitter.

For data communication between the transmitter and the receiver in the product, this ID is used to

determine which facility (transmitter) the data has been received from.

The "ID" is labeled on the side of the transmitter.

Page is loading ...

Contec CPS-PAV-AE01-JP Owner's manual

Contec CPS-PAV-AE01-JP Owner's manual

Contec CPS-PAV-AE01-JP Owner's manual

Related papers

Other documents